Search Documents

By Marc Dondelinger

Interlocking H sections with deep webs and high section modulus are being used for cofferdams and shore enclosures where pressures are excessive. The H sections can be as much as a meter deep; they can be used as continuous interlocked wall. A steel saving alternate is spacing the H and driving deep for stability then filling between with shorter interlocking sheet piles. Templates provide for exact positioning.

Jan 1, 1985

By Jorge Beim

Helical Piles are increasingly being used to support and rehabilitate structures subjected to compressive axial loads. Traditionally, empirical correlations between installation torque and load capacity of helical screw piles are used as the field quality control. Load tests, however, are always recommended to validate the installation process and design methodology. This paper describes a test program performed on helical piles installed at the National Geotechnical Experimentation Site of the University of Massachusetts - Amherst campus (UMass-Amherst), well known for its deep varved clay deposit. Seven of these piles were submitted to Dynamic Load Tests using the Pile Driving Analyzer® (PDA), and also to Static Load Tests. Good agreements were obtained between the results of the dynamic and static load tests, encouraging the use of the former testing method as a viable alternative to the latter for determining the compressive load capacity of helical piles installed in cohesive soils. The results of the load tests were also compared to the predictions based on torque correlations, resulting in correlation coefficients which were higher than the ones traditionally used.

Jan 1, 2012

By Dilip Khatri

Helical pile anchors have gained acceptance over the past sixty years. Most recently they have been commonplace in the 20th century for the power utility industry in anchoring transmission towers, equipment platforms, street lighting, telephone poles, and radio tower applications. They have a strong proven industrial track record in these industries. As the cost of conventional deep pile foundations rises, the practical benefits of helical pile anchors becomes evident as a practical alternative. Noted for their uplift capacity, helical piles demonstrate equally strong compressive capacity as a structural foundation element. This paper summarizes the history, practical benefits, and technical requirements for helical piles. Significant structural testing has been completed at various universities. The practical benefits of these tests are discussed. One case example of proven performance is presented to demonstrate the advantages and disadvantages of helical pile anchors as suitable foundation elements.

Jan 1, 2003

By Matthew Janes

Quality control procedures are increasingly important with today's higher capacity foundations and complex loading conditions. The need for a mobile, repeatable, nondestructive and economical load test method led to the development of an entirely new approach. The system described involves using solid propellant fuels to accelerate a reaction mass off the test pile. The force required to accelerate the reaction mass upward acts equally downward on the pile. Very high forces may be applied to the pile in a controlled, linearly increasing manner. The duration of the applied load is approximately 100 milliseconds. This rate of loading is slow enough to allow the pile and soil to react together as a composite rigid body. Pile/soil accelerations and velocities are low, typically 1 g and 1 m/s respectively. The effects combine to produce pile and soil response no longer dominated by the transfer of force via stress pulse (as with impact). Instead the pile force increases throughout the length of the pile, with pile top and toe stresses building in unison with time. This emulates the stress condition during static pile loading. Finally, state of the art instrumentation systems are used to obtain test data. Displacement is monitored directly using a laser datum and integrated receiver located at the centre axis of the pile. Force is also monitored directly using a calibrated load cell. Data is acquired and digitized using a 386 PC with user friendly software capable of producing load deflection curves and time histories in the field seconds after testing.

Jan 1, 1990

By A. R. Jambekar

City of Bombay has been developed out of former 7 islands. Landmass of 434 sq.km. of Bombay, started looking inadequate for further growth and expansion of Bombay City. In order to develope twin city of New Bombay, State Government formed fully owned Company "City and Industrial Development Corporation of Maharashtra Limited", (CIDCO) in 1971 and entrusted it with planning and development including social and physical infrastructure of New Bombay.Hence, Trans - Thane Creek area is being planned and developed, to serve as counter-magnet to Bombay. Area of 343 sq.km located on the main land, is fast developing into a satellite community, for India's overcrowded financial capital. Thane Creek, running in almost North-South direction, separates Bombay City from main land and posed a significant barrier, to further expansion of city's sprawling suburbs, until, it was bridged for the first time in 1972. On the basis of traffic study, CIDCO decided to construct an additional road link across Thane creek to cope up with future projected traffic. This bridge will connect Airoli in New Bombay and Eastern Express highway near Mulund. Bridging the vast, exposed tidal Thane Creek, have always posed challenging conditions, during constructions of these bridges. In this paper, case history of deep open foundations provided for Airoli Bridge is presented.

Jan 1, 1996

By Lucien P. Weber

Over the last few years, increased customer demands as well as strong competition from substitute materials have accelerated the development of advanced technologies to improve both the performance and the cost-effectiveness of steel H-piles. On the material side, the development of an in-line heat treatment, combined with the most advanced steelmaking and rolling techniques, allowed to create a new generation of high-strength low-alloy steel grades, called HISTAR, achieving yield points up to 500 MPa (~72 ksi) and yet maintaining excellent weldability properties thanks to a low carbon equivalent. The topic of this paper is to illustrate the performance of H-bearing piles in HISTAR steel grades. In 1989, a major test program was started at different locations in Hong Kong, which is renowned for its difficult soil and severe driving conditions. After the successful completion of these tests, the HISTAR bearing piles were accepted by the local building authorities. Thanks to their cost-effectiveness, the HISTAR bearing piles have subsequently been used with great success in areas with appropriate soil conditions, especially in Asia and more recently in Europe.

Jan 1, 1997

By W. Tom Witherspoon

Many Engineers are skeptical and cautious about skin friction factors for the portion of drilled piers where temporary casing is used. This has led Texas engineers in many cases to eliminate skin friction values for the cased section, which necessitates deepening the drilled shaft to compensate for the loss in the cased section. This paper has provided field test data that supports inclusion of skin friction in the temporarily cased hole section as a contributing factor in total axial capacity as comparable to open hole shafts of the same diameter. Reasons for the resultant friction values are provided including; remolding of the cased clay section and the increased pier circumference necessitated by the oversized casing required for adherence to the engineers shaft diameter specification.

Jan 1, 2009

By Martin C. Jones

This paper outlines the development of small diameter grouted piling, to deal with foundation problems in difficult soils conditions and in very restricted access areas. A number of applications are outlined to show the way in which these piles have been used over the last sixteen years in Canada. PICKERING GENERATING STATION - ONTARIO HYDRO UNDERPINNING OF SCREENHOUSE - TRASH DISPOSAL AREAS Between 12th July and 29th September 1971, 40 small diameter grouted piles were installed in the screenhouse at Pickering Generating Station. Access was extremely restricted as the screenhouse had been completed and the majority of mechanical equipment had been installed. The two ends of the screenhouse had been built on granular fill which overlies till and shale bedrock and settlements had been observed which it was decided had to be halted even though the rate of subsidence had decreased. Two diamond drills were employed to install 8 inch

Jan 1, 1987

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By Sun Shao Xian

The Port of Shekou is situated at Shenzhen Bay on the east side of the Pearl River estuary. Geological condition of the site is quite complicated. On top of the sea bed, there is a layer of soft silt 8 - 14 m thick. Under the soft silt, there are intercalated layers of sand, silt and clay. Average surface elevation of the underlying undulatory weathered bed rock is about - 20 m, with a variation of about 10 m. In certain locations, the weathered bed rock is covered with a layer of silt 3 - 4 m thick. This paper gives brief account of three types of wharf structures which are of particular interest, constructed in the last few years: (A) Platform type wharf structure with frontal sheet piling and steel raking pile in the rear; (B) Relieving Platform type structure with steel sheet piling and inclined anchoring HP pile ; (C) Steel pipe pile row supported apron added to a marginal quay. Average construction time of a deepwater berth is about six months.

Jan 1, 1991

By W. Sondermann

"AbstractWith the increasing demand in reuse of inner city areas and the urgent need for deeper foundation pits under cramped circumstances, adjacent structures close to and high ground water level, the well-known established technologies especially with small to mid-sized dimensions are often too time consuming and occasionally not economic to install lateral support systems. The alternatives for these specific cases could be the usage of the deep mixing technology to create lateral support systems in reinforcing the deep mixing elements additionally to transfer the horizontal loads from earth – and water-pressure.With increasing demand in depth and water tightness, verticality and overlapping of single column solutions are becoming the key in execution. In addition, for some applications subsoil-conditions were not ideal for wet deep mixing technologies. The tubular soil mixing system (TSM) as a combination of mechanical mixing and support of hydraulic cutting by jet grouting can provide solutions toovercome these challenges.1. Current market conditions and trendsThe present financial crisis and the efforts not only to consolidate national budgets, but also to rescue certain banks, have not left the building industry unaffected either. Some drastic cutbacks to public budgets, along with the increasingly restrictive granting of credit for the financing of construction projects, have led to enormous over-capacities in the building sector, with purely negative impact. As a consequence of these negative developments, many companies are experiencing the pressure to restructure more quickly and to reduce costs but at the same time to keep the consequences of all activities, both externally and internally, within limits acceptable to employees, owners and finance institutions and last but not least consumers."

Jan 1, 2014

Jan 1, 1988

By Karl A. H iggins, James P. Racine

"Displacement Cast-in-Place (DCIP) piles are not a common deep foundation type in the Washington, DC Metro Area market. As a result, less regional data is available for these foundations compared to other alternate deep foundation types. Displacement cast-in-place piles (DCIP) differ from traditional Auger Cast-In-Place (ACIP) piles in that the pile annulus is formed by pushing a partially-flighted, auger bit to depth via a large mandrel. The auger bit includes a displacing body near the bottom of the tooling. Therefore, little to no spoils are generated during installation and the soil around the annulus is largely densified in-place due to the displacing body being slightly larger than the mandrel it is attached to.Due to this densification, one would expect that the theoretical DCIP capacities (compression or tension) would be greater than an ACIP pile (assuming a pile of similar length and diameter). After 20 static load tests and the installation of over 6,000+ piles on the MGM National Harbor Casino Project, the differences in pile support characteristics between DCIP and ACIP piles of same size and depth was small. The performance of both pile types depended on the density and type of soil within the bearing stratum. In some early cases of DCIP use, the performance exceeded expectations and appeared to be more in line (or better) than typical capacities obtained from driven displacement piles. Other times, the tip elevations could not be achieved or were so difficult to achieve that installation delays occurred and/or significant additional engineering effort was required to address piles short of their requirement embedment.This paper will discuss the limitations of DCIP pile installation in dense Coastal Plain soils and will present the lessons learned during this project. The paper will also compare the DCIP pile type to both conventional ACIP and driven displacement piles utilizing regional and site-specific load test and installation data."

Jan 1, 2017

By Abdul Aziz Hanifah

A novel instrumentation and analysis technique, called GLOSTREXT method has recently been introduced for bored pile load tests in Malaysia. This technique provides an innovative and improved alternative for conventional bored pile instrumentation methods commonly practiced for the past few decades. Results for five case histories involving full scale static load tests for high capacity bored piles with both new and conventional instrumentation details placed in within the same instrumented piles are presented to demonstrate the advantages of this novel technique. Results show good agreement between the new and conventional instrumentation.

Jan 1, 2006

By Mark Maday

As part of the I-94 North-South Corridor reconstruction program, the Wisconsin Department of Transportation (department) is reconstructing the Mitchell Interchange in Milwaukee, Wisconsin. Located on the south side of Milwaukee near Mitchell International Airport, The Mitchell Interchange interconnects I-94, I-43 and I-894. Reconstruction began in 2009 with the letting of the first advance contract for local crossroad bridge reconstruction. A second advance contract for construction of collector-distributer roads on each side of the I-94 mainline was completed in 2010. The main contract involving reconstruction of the core of the Mitchell Interchange was let in the summer of 2010, and is scheduled to be completed by the end of 2012. The core contract includes construction of three cut and cover tunnels along two system interchange ramps. Construction of the three tunnel structures is on the critical construction path. The contract includes an interim contract completion date that requires the tunnels to be open to traffic by the end of 2011. A top down method of construction using drilled shaft secant piles for the sidewalls of the cut and cover tunnel structures was selected as the preferred structure type to address subsurface and construction schedule challenges. The department identified in pre bid coordination that no cost reduction incentives would be reviewed or accepted for changes in tunnel wall type. A major component of the tunnel structures requires the installation of 1,500, 4-foot diameter secant piles. This paper presents mitigation strategies to manage construction risks associated with the installation of the secant piles including; prequalification of the secant pile subcontractors, requirement for use of full depth temporary casing, a site specific quality control plan, specifying drilling equipment, and developing a geotechnical baseline report for this critical component of the Mitchell Interchange reconstruction project.

Jan 1, 2011

By Onur Kacar

A numerical approach has been implemented to assess the settlements of pile groups bearing in clay. A three-dimensional finite element program has been utilized to model a vertically loaded spread footing, a single pile and a pile group. The soil-pile interaction was modeled with elastoplastic soil and interface elements. The model has been calibrated using a full scale load test results of the spread footing. The load transfer between the pile cap and the piles was assessed and compared with the measured load transfer. The predicted settlements for the pile group were compared with the settlements measured in the load test. Two analytical methods were adopted to predict the pile group settlements and they were compared with the measured values. The group effect determined from the analysis and load tests was compared with the interaction factor approach. It was shown that three-dimensional finite element approach can be successfully utilized to assess the soil-structure interaction and hence the load transfer between the piles and pile cap. Also, it was shown that the interaction factors method and equivalent footing method work well in the working stress range, however they underpredict the settlements at larger loads. INTRODUCTION The settlement and stress distribution of pile groups have been traditionally estimated based on load test results of single piles and accounting for the group effect using various approaches. The most widely used approaches are group interaction factor method, equivalent footing method and equivalent pier method. These approximate solutions are used very commonly in practice as full-scale load tests on pile groups are very expensive and time consuming. These approximate solutions are also adopted in design guidelines such as AASHTO LRFD Bridge Design Guidelines (2014) and FHWA Design and Construction of Driven Pile Foundations (2016). In this paper, a full-scale foundation load tests performed by Nagai et al. (1961) and reported by Koizumi and Ito (1967) is modelled using a three-dimensional numerical method. The settlements and the stress distribution on foundations were then compared with the traditional equivalent footing method and interaction factor methods.

Jan 1, 2018

By George Piscsalko

"Quality control of drilled shafts and CFA piles is greatly dependent upon the practices of the site personnel. In many applications it is difficult or not possible to fully inspect the shaft prior to concreting, such as when the shaft is drilled under slurry. CFA piles are cast with no ability to inspect the shaft prior to concreting. There are numerous methods currently available to assess the integrity of drilled shafts and CFA piles. This paper will compare evaluations by three existing non-destructive test (NDT) methods with a new method of Thermal Integrity Profiling for assessing integrity in drilled shafts and CFA piles. This Thermal Integrity Profiling method determines the integrity over 100% of the shaft cross section, both inside and outside the reinforcing cage, by measuring the hydration temperature of the concrete along the length of the shaft. These temperature measurements are made typically only 12 to 48 hours after concrete placement, thus accelerating the construction process. Thermal Integrity Profiling will be described in detail and the Thermal Integrity Profile (TIP) results from several shafts with purpose built defects will be discussed along with several case histories from drilled shafts and CFA piles where Thermal Integrity Profiling was used. The case histories will compare TIP with various other NDT tests utilized on these particular piles including comparisons with Low Strain Integrity Testing and Cross Hole Sonic Logging. Test results for the various methods will be discussed and the excavation of the upper portion of one drilled shaft will be shown and discussed. IntroductionDrilled shafts can be a desirable foundation element in many applications due to the large axial and lateral capacities which are attainable for very large drilled shafts. Drilled shafts can be cast in a dry hole which allows for inspection of the hole prior to casting, but the casting process is very difficult to nearly impossible to inspect with any accuracy. Drilled shafts are frequently cast under slurry as a means to stabilize the surrounding soils during the construction process. When casting a drilled shaft under slurry, it is very difficult to accurately inspect the hole prior to casting and it is equally difficult to inspect the shaft during the casting process. CFA piles are another popular choice for their relative ease and speed of installation. The trend has been larger CFA piles carrying greater loads, which makes quality control critical for these piles. Many of the above mentioned processes are blind to inspection and therefore the chances increase for having defects present in the completed elements."

Jan 1, 2014

By Lu Peiyan

A computation model of soil-pile (wall) interaction under lateral loading is presented in this paper. The model has been applied to some engineering projects, and the comparison between computation result and measured result shows good agreement, so the model is proved to be correct and practical.

Jan 1, 1991

By David J. Baxter

Use of bored displacement piles has experienced significant growth in the UK piling market sector, largely due to their environmental advantages over other piling methods and through cost benefits. Bored displacement piles are a cast-in-situ construction which can be formed with minimal production of spoil and offer low noise and vibration compared to driven displacement piles. A large variety of bored displacement piles have been developed. This paper describes a standard system for their classification. The development of the different types is described along with the factors which have led to their increased use. Consideration is given to processes undergone by the soil during pile installation and design approaches for bored displacement piles are compared. Comparisons are made between the different classifications of bored displacement pile. Comments are also made on the installation of such piles. It is concluded that complex changes occur in the stress states of the surrounding soils. Such effect of the pile installation on the soil should be accounted for and there is a need, therefore, to further refine the design process for these piles.

Jan 1, 2006

By C. Van der Veen

The use of the quasi static (Dutch) Cone Penetration Test (CPT) is described as a tool to predetermine the ultimate bearing capacity of the pile point. An analysis is given why a purely theoritical approach does not meet with success. A practical method is explained of extrapolating the cone resistance to predict the pile point resistance. The method has been calibrated against the result of 32 selected high standard loading tests on pile points in the Netherlands.

Jan 1, 1989