Search Documents

By J. E. Armstrong

"IntroductionT'HE PRODUCTION of gravel and sand may be considered to be the major mining operation in the Lower Fraser Valley of British Columbia. At least thirty pits are in operation with a yearly production probably in excess of two million yards and a value in excess of one million five hundred thousand dollars before crushing, washing, and sizing. The value of the finished products would probably be double the above figure.Since 1949, the writer and his co-workers have been engaged in the geological investigation of the Lower Fraser valley and adjoining Coast mountains for the Geological Survey of Canada. The study, which is not yet completed, includes both bed-rock geology and geology of the unconsolidated sediments lying above bed-rock. In a rapidly expanding industrial area, .an advance knowledge of the geology may• greatly aid in future 'planning, and in many cases may .prevent not only the wastage of large sums of money, 'but possible disaster. Some of the present and future applications in which geological information in the Lower Fraser valley should be of value are as follows: the development of domestic, irrigation, industrial, and municipal groundwater supplies; drainage for industrial sites,, roadbeds, and farmlands; flood control along the Fraser river and smaller streams in the area; the location of dam sites, of major tunnels for water supply •and sewage, of road-beds, of foundation sites for large buildings .and other engineering undertakings in which geology may aid; the evaluation of oil and gas •possibilities; the production of building stone; and the production of sand and gravel, the subject with which this paper is primarily concerned."

Jan 1, 1953

By W. L. Hunter

The preparation of coal for the commercial market is a study both varied and wide, and can be viewed from many angles and in different ways. This short paper can but touch upon the subject and is intended to discuss briefly preparation plants which in some cases would seem to be quite inadequate. The conditions confronting most operators are similar, inasmuch as the existing plants were not built specifically to prepare a product for the market of today, but rather of yesterday. The tremendous strides made in the field of combustion in recent years require that the product be of the highest grade procurable, and in a glutted and somewhat restricted market the buyer may be more pernickety than otherwise. These would appear to be the conditions of today. Where a mine is operated individually, better all-round results seem more readily procurable than in a consolidated effort where so many different conditions are sure to arise demanding cognizance, and in many cases requiring to be incorporated in the scheme of things. In the case of a number of mines being administered to form a central source, that source not having had anything to do with the bringing into being of the institutions over which it presides, we find some of the mines well equipped with facilities to properly screen and load the coal, while in others the facilities are not so good, but are doing their share towards delivering a product that will pass muster and in such quantities that they can be counted on.

Jan 1, 1930

By J. E. Ryan

General Description Due to the extreme cold weather experienced in Flin Flon during the winter months, thought and precaution were necessary in the design of the plant buildings. The machine shop, carpenter shop, drill shop, and coal plant buildings are similar in the building materials used in their construction. They are sided with two-inch shiplap, insulated with celotex and asbestos paper, and covered with corrugated iron on all side-walls. Roofing consists of 2 by 4 lumber on edge, laminated, and further covered by celotex and three-ply roofing. These buildings are heated by means of unit heaters. The heaters are primarily steam-heated radiators, through which the air of the buildings is circulated by electrically-driven fans. Our machine shop is located to the east of, but central to, the main operating buildings of the mine and plant, and is so connected by a net work of tracks as to be able to serve all portions of the entire plant conveniently. The building is divided into two bays, the main bay 53 ft. by 340 ft., and the east bay 24 ft. by 340 ft. The shop office and drafting room, a two-story annex 24 ft. by 30 ft., is located on the west side of the shop. The arrangement within the shop is such as to house conveniently the several departments, namely, heavy machine tool section, repair floor section, boiler shop heavy tool and floor section, blacksmith heavy tool and forge section, tool room, electric welding rooms, stock room, tin and copper shop, and electrical parts and armature winding and repair shop (see Figure 1). All the heavy tools, the repair floor section, and railway tracks are so located in the large open bay as to be fully serviced by an electrically operated 15-ton bridge crane, with a span of 50 feet and a travel the full length of the shop. A standard-gauge railway track, branched off the main line, penetrates the full depth of the building. This track lies along the extreme east side of the main bay, allowing easy entrance and movement of rolling stock and heavy machinery, loaded on standard flat-cars, to the repair floors in the main bay. Eight jib cranes, affixed to building columns, further facilitate the heavy repair work throughout the various shop divisions. Our light and heavy machine tools are standard equipment, not unlike tools used in mine, mill, and railway shops.

Jan 1, 1935

By L. Frost

"Since the late 1990s, increased prevalence of severe lung disease among US coal miners has been observed, particularly in central Appalachia where thin-seam mining is prevalent. While respirable silica exposures have been implicated in many cases, the available dust monitoring data from mines shows no explanatory trends. One possible factor could be differences in the relative toxicity of silica particles based on their surface condition. Previous research has indicated that particles with occluded surfaces (e.g., by a thin layer of clay) may be less toxic than those with non-occluded surfaces. However, this dust characteristic has not been investigated before now in central Appalachian mines. In the present study, 18 respirable dust samples from seven central Appalachian mines and two northern Appalachian mines were analyzed to assess the relative occurrence of surface-occluded silica. Results showed that the dust from central Appalachian mines actually had higher fractions of occluded silica, which may be due to extraction of large amounts of rock strata along with the coal. However, the central Appalachian mines also more silica particles overall (i.e., occluded + non-occluded) in terms of total number percentage of respirable particles.INTRODUCTIONResurgence of occupational lung disease among US coal miners, especially in the central Appalachian region, has been observed since the late 1990’s (Gibson, 2016; Zosky et al., 2016; Suarthana et al., 2011; Gamble et al., 2011; Antao et al., 2005; Attfield & Sexias, 1995). In addition to increased prevalence of simple Coal Workers’ Pneumoconiosis (CWP, or “black lung”), the prevalence of severe and rapidly progressive disease has risen dramatically (Almberg et al., 2018; Blackley et al., 2018a, 2018b, 2016, 2014; Graber et al., 2017; Cohen et al., 2016). While exposures to respirable silica have long been known to cause or play a role in diseases such as silicosis or progressive massive fibrosis (PMF), which is conventionally considered as the most advanced form of CWP, it is unclear whether silica is the only culprit in the recent outbreak of severe disease. Indeed, as disease rates have risen, both total respirable dust and silica concentrations generally appear to have declined since the late 1980s, based on regulatory monitoring data in the most affected mining districts (i.e., MSHA coal Districts 4, 5 and 12, which cover central WV, eastern KY and southwestern VA, and southern WV, respectively) (Figure 1). Of course, the latency of disease can vary and may be or more 10 years, but many of the most recent cases are likely to have resulted from exposures that occurred since the late 1980s."

Jan 1, 2019

By J. W. Reynolds

Introduction The Sullivan mine, at Kimberley, B.C., is the principal source of ore for the Consolidated Mining and Smelting Company of Canada, Limited. Current production amounts to about 2,500,000 tons of lead-zinc ore a year. With approximately 1,600,000 feet of percussion drilling and 700,000 feet of diamond drilling being carried on each year, any improvements in drilling practice are important. Testing of new equipment and drill bits is a major function of the Testing Department at the mine. Tungsten carbide bits have been the subject of many tests since 1947 and have been used in operations since 1948. This paper details with the methods of testing and gives comparative data on performance and costs for tungsten carbide bits as compared to steel bits. Operational use of tungsten carbide bits started in April, 1948, and the extent of application has increased considerably since that time. The scale of employment is illustrated in Table I, which also shows other statistics on the use of carbide bits. Up to the present time eighteen types of carbide bits or tipped steel, as made by six different manufacturers, have been tested. In general, one supplier's bits have been used in operations, but some large-scale operational tests have been carried out with other types. The types tried are shown in Table II. To date they have been, the subject of 33 tests, covering the destruction of 804 bits over an observed footage of 42,586 feet.

Jan 1, 1951

By John D. Carr

Introduction The Flin Flon zinc plant operates on what is known as the low density or standard sulphate process, that is, the zinc is carried through the plant solution circuit attached to the SO4 or sulphate radical at a concentration not exceeding 175 grams per litre zinc. The process may be described briefly as follows: The zinc is received in the zinc concentrate chemically combined with sulphur and mixed with many other impurities. The concentrate is roasted and most of the sulphur is burned to a gas, which is discharged from the plant. The roasted concentrate, or calcine as it is called, is leached with a weak sulphuric acid solution so that the resulting leach solution contains a high zinc content but a very small proportion of the impurities. The solution is separated from the solids and is purified further by agitation with zinc dust to remove copper, cadmium, and cobalt. This purified zinc sulphate solution is then pumped to the electrolytic department. The solids from the first leach are again leached, but this time with a stronger acid solution to dissolve all of the remaining zinc which is soluble in the strength of acid available. The solids and solution from the leach are then separated. The solids are stock-piled for further treatment at some future date and the solution, carrying a relatively high amount of impurities, is sent to the first leach, where the chemical action is such that the contained impurities are precipitated as solids. The electrolytic department is nothing more than a large number of electroplating cells in which the zinc is plated on aluminium sheets. Since zinc does not plate tightly to aluminium, the zinc plating or sheet is easily stripped from the aluminium and the sheets are collected to be melted and cast into the standard market bars or slabs. In the electro-deposition cells, the zinc sulphate (ZnS04) is split to metallic zinc (Zn) which plates out, and sulphate (S04) which combines with the hydrogen of the water of the solution to form sulphuric acid (H2S04). When one pound of zinc is deposited, about one and one-half pounds of sulphuric acid are formed. This acid is sent to the leaching section, where it dissolves one pound of zinc from the calcine. The solution is purified and is again pumped to the plating cells. The solution travel forms a complete circuit.

Jan 1, 1935

By R. Matusewicz

The key drivers for the copper smelting industry are a complex mix of economic and "human" factors which combine to drive technology in new directions and can provide a strong indication of future industry trends. Recent examples have been the drive to achieve increased scale of production and resultant cost efficiencies by using a single furnace high intensity smelting vessel, and the broad acceptance of Top Submerged Lancing (TSL) technology for this duty. The development and adoption of continuous converting processes to counter the increased pressures faced by the Peirce Smith converting process is another example of the need for innovation. This paper discusses the merits of the continuous converting process, describes how the Ausmelt TSL batch converting process has been adapted to the new Ausmelt Continuous Copper Converting (C3) process in response to these industry trends and examines the Ausmelt continuous converting flowsheet options available to the end user.

Jan 1, 2007

By F. R. Jones, B. W. Taylor, A. R. MacPherson, L. J. Lamb

"The Lake St. Joseph Iron Deposit is in Northwestern Ontario. Exploration to date by Steep Rock Iron Mines Limited has indicated an ore reserve of 683 million long tons. Metallurgical investigations have proved that suitable oxide pellets and/or superconcentrates can be economically produced from this ore. Studies of the Lake St. Joseph iron ore deposits have covered the period 1956-71, and have embodied applications of the improvement in mining and processing technology over this period. Market demand in the early 1960's for high-grade oxide pellets as a replacement for natural iron ores for the blast furnace first drew attention to the potential of the Lake St. Joseph deposit. The current market trend toward utilization of sponge iron to replace steel scrap as feed to electric furnaces and cupolas now suggests that the deposit can better be exploited as a prime source of superconcentrates."

Jan 1, 1972

By J. C. Kingston

Introduction The sliding-form method of erecting concrete structures was first devised and used in the early part of this century by the Sante Fe Railroad Company for the erection of a grain elevator at Santa Fe, New Mexico. A somewhat related principle has been employed for a number of years in shaft lining work and, to our knowledge, was perfected in Butte, Montana, but until the building of the concrete headframe at the Jeffrey mine of the Canadian Johns-Manville Company, Ltd., at Asbestos, Que., the method, as applied to surface structures, was quite foreign to the mining industry in Canada. The current shortage and cost of structural steel shapes has no doubt contributed more than any other single factor to the investigations that have led to the use of reinforced concrete as a headframe building material. Mining men in western Quebec and northern Ontario have shown a great deal of interest in the design and construction of the headframe at the East Sullivan mine in Bourlamaque township, Que., and we have had many queries regarding the methods used and, in particular, for an explanation of the sliding-form principle. This article is written in an attempt to set forth the conditions which were to be met; to explain the construction methods used, and to discuss the economy of concrete headframes as compared with the conventional steel structures with which the mining fraternity is familiar.

Jan 1, 1949

By M. F. Goudge

BRUCITE associated with highly metamorphosed Precambrian limestone was discovered in the vicinity of Rutherglen in northern Ontario by the writer during field work on the limestones of that district in 1937, and later was identified in similar limestone at Bryson and Wakefield, Quebec. The brucite occurs as granules disseminated through the limestone (Figure 1) and comprises from 20 to 35 per cent of the rock. Such rocks may be referred to as predazzites or pencatites, depending on the proportions of the constituent minerals. In this paper, however, the general term brucitic limestone is used to designate limestone containing brucite. In none of the deposits does the magnesia content of the rock approach that of magnesite, and in the deposits near Bryson and Wakefield the magnesia content is only that of dolomite. Therefore, without some method of concentrating the brucite, the deposits would be of little or no more value as a source of magnesia than is ordinary pure dolomite, which is abundant in many parts of Canada. Investigations in the laboratories of the Bureau of Mines have, however, resulted in the development of a method whereby, from certain of the deposits, pure calcined brucite, or magnesia, in granular form can be obtained, apparently at a cost that will enable it to compete in eastern Canada with imported magnesia. The granular magnesia so obtained appears to be highly suitable for use in basic refractories, for making magnesium metal, and for various other purposes for which magnesia is commonly used. Prospecting in the neighbourhoods of the original discoveries has resulted in a number of other deposits being found in each of the three areas, and there is now apparently available s1.dficient brucitic limestone of a grade that will lend itself to commercial exploitation to supply for many years a large part of the present and prospective Canadian market for magnesia and its products. Furthermore, it is expected that additional deposits will be discovered as prospectors and others become more familiar with the appearance of brucitic limestone.

Jan 1, 1940

By Matthew D. Meyer

SMART, an association of surface mining companies formed in 1995 to develop a coordinated approach to technology development for the mining industry, has recognized the need for the establishment of a worldwide database that continuously collects mining equipment data and provides metrics related to productivity and cost. Under the auspices of SMART, Syncrude Canada, Suncor Energy and Albian Sands Energy (three oil sands mining operations located in northern Alberta) have established a pilot project for mine benchmarking. This presentation will include a review of the pilot progress including: ???Data gathering techniques: means of collection and storage, proposed practice for data control and normalization, access to data/reports and format for data. ???Reports/analyses for individuals, across groups, within the total industry pool and publicly. ???Security and confidentiality of information belonging to identified parties. ???Sharing of best practices among members. SMART has identified two key deliverables to ensure success of the project. First, data supplied from surface mines must be validated and normalized to common definitions and then analyzed to provide participating companies with regular reports that allow them to understand their position and resultant opportunities to achieve world-class performance. This model maintains granularity of the data for each operation that can then be recombined into standard comparisons or specific indices as required. The general categories of: operating delays, maintenance downtime, standby, and scheduled downtime, have been used to frame comparisons. Second, participating companies are looking to go behind the indices to identify and share best practices that distinguish particular operations. The spirit of cooperation between the companies involved in the pilot project is meant to be a model for future expansion of the benchmarking project.

Apr 1, 2005

The Autogenous milling of ores holds an increasing attraction as the focus moves towards reducing energy usage, both direct and embodied in grinding media. However, most of the early AG mills were converted to SAG for improved stability and increased throughput. This imposes a huge penalty in steel grinding media consumption. The LKAB iron ore operations in Sweden process highgrade magnetite through fully-autogenous milling lines to a final product P80 of about 45µm. The outcomes of P9O AMIRA research surveys, covering a wide range of mill fillings and throughputs and with different feed blends, are presented. Insights are provided on operational strategies, opportunities, the influence of feed size control and balancing the blend of competent gangue and softer magnetite. Areas of importance in the successful operation and control of energy-efficient autogenous circuits are highlighted.

Jan 1, 2012

By P. O. Sandstrom

"Atlas Copco is introducing a new patented method for full-face boring. This paper presents the basic principles of the boring action and discusses the present experience regarding performance and costs. The Atlas Copco ""Full-facers"" are designed for hard-rock applications, although they are successfully boring in soft ground without major changes. The unique patented boring principle referred to as the 'Undercutting Method' permits these machines to bore, economically, in harder ground than machines based on the 'crushing principle'. This is mainly due to considerably lower cutting-tool costs, as the tungsten carbide tips only are in contact with one-third of the bored volume. The remaining rock is 'undercut' and peels off from a slight back pressure.The undercutting method also permits boring of non-circular headings and Atlas Copco has already manufactured two machines for rectangular drifts. This concept could revolutionize development work in mines employing trackless equipment."

Jan 1, 1971

By J. M. Cummings

DURING the past year, the writer has investigated the treatment of a variety of British Columbia tungsten-bearing ores. Much of the test-work described in this paper was carried out in collaboration with Mr. A. G. Lyle in association with the British Columbia War Metals Research Board at the University of British Columbia. The remainder was completed in the laboratories of the Department of Mines at Victoria. Two mills in the Province are at present treating tungsten ores. Descriptions of these are included through the co-operation of Messrs. S. Gray (1) and A. A. Almstrom (2). MINERALOGY, OCCURRENCE, AND SPECIFICATIONS In the present paper, attention is directed solely to scheclite, inasmuch as known occurrences of other tungstcn minerals in British Columbia are of mineralogical interest only. The properties of scheclite are listed below: Percent W03 .. 80.6 Tenacity ...... Very brittle Çrystallization Tetragonal Lustre ........ Vitreous to resinous Cleavage ...... Good in 4 directions Magnetism ... Non-magnetic Specifie gravity 6.05 Diaphaneity .. Transparent to translucent Hardness. . . . . . 4.5-5.0 Scheelite may contain as much as ten per cent of molybdenum in solid solution, but most of the specimens from British Columbia examined by the writer were relatively pure.

Jan 1, 1943

By A. Aaltonen, S. Paloranta, H. Myllykangas

A property based dynamic model of flotation was built and validated for training purposes. The model is based on the work of the AMIRA P9 project. The recovery of each particle with composition and size is calculated in a given simulation step. The model takes into account machine and operational parameters such as air flowrate and froth height. The model was created using fullscale test data on Pyhlisalmi Cu-Zn-pyrite ore with flotation kinetics of multiphase particles determined. Simulation and validation shows that model can predict the dynamic behavior of the process accurately enough for training purposes.

Jan 1, 2009

By Robert S. Penczak

Red Lake Gold Deposits ? Descriptive Classification (modified from Pirie, 1982) VHR Au -- Volcanic-hosted (vein & wall-rock) replacement Au deposits ~93% of camp production Q-(T) Au -- Quartz-(tourmaline) vein Au deposits ~7% of camp production Quartz-sulphide Au deposits Porphyry-hosted sulphide Au deposits Current & Significant Past Producers Camp Production 21.6 M oz / 672 tonnes Au Other Deposits / Occurrences (Intermittent Exploration

Apr 1, 2005

By E. Wraith, W. W. Culver, B. Wesstrom, P. J. Mackey

Electrodeposited copper of the 1860s was of unprecedented purity, although the profound significance of this achievement was not fully realised until the dawn of the electrical age a decade or so later. By the 1870s there were three somewhat large (4 to 4.5 tonnes Cu/day) electrolytic copper refineries in Germany based on J. B. Elkington’s process, first patented in the United Kingdom in 1865. More such refineries were planned throughout Europe. At the same time, copper output in the U.S.A. was starting to expand and with the spread of European electrolytic copper refining technology across the Atlantic, the door opened to major increases in North American output. The technology was first taken up in 1879 by James Douglas at the Chemical Copper Company in Phoenixville, Pennsylvania, where he was Superintendent. Douglas was assisted in this pioneering work by Edward Weston. The copper refinery at the Chemical Copper Company was small, not unlike the first plants in Europe. The present authors contend that the electrolytic copper refinery at the Chemical Copper should be regarded as the first copper refinery in the United States. The Balbach Copper Refinery in New Jersey, which commenced operations in 1883 with an initial production of about 2 tonnes Cu/day, has been erroneously considered as the “first commercial refinery”; it rightly belongs in second place. The early developments at these plants are discussed in this paper. INTRODUCTION In the mid-1800s, the main uses for copper were as sheathing on the wooden sailing ships of the day to protect from marine growth, boiler components in locomotives and steam engines, along with some construction uses. Copper ores were generally smelted, and further fire-refined for market. The recovery of gold and silver, if present in payable amounts, was a slow and relatively expensive step. This situation regarding copper would change by the 1870s with advances in the generation and use of electricity. The introduction of the dynamo led to major developments in electrorefining. First demonstrated in principle by Faraday in 1831 (Faraday, 1832), the dynamo was subsequently adapted and further developed by J.S. Woolrich for electro-metallurgical applications in 1842 (Woolrich, 1842; Napier, 1845). It provided a new source of power with the unprecedented potential to significantly change the scale of metal production by electrometallurgy. Interestingly enough, copper would be needed for the electrical age just beginning. By 1869, advances in dynamo design offered relatively reliable large machines, which enabled J. B. Elkington in the United Kingdom to use the dynamo in the radically new Pembrey copper electrorefinery — the first copper electrorefinery in the world (Wraith, 2013). Initial production at Pembrey was small — in the range of 1 to 2 tonnes/day — while gold and silver were recovered more readily by the treatment of the slimes than with methods used hitherto.

Jan 1, 2019

By Linda Dufour

"Autoclaves have been in commercial use in the mining industry since the early 1950's the initial applications included tin, uranium, cobalt, nickel and copper extraction under both acidic and alkaline conditions. These circuits varied in batch or continuous operation. The geometry has been spherical, vertical, and horizontal type with up to six agitators, with throughput as high as 1000 stpd.Presently autoclaves are a good process selection for many refractory sulphide gold bearing ores. The first application of pressure oxidation in the gold industry was at the Homestake Mcglaughlin's Mine which was commissioned in 1985. This was an acidic pressure oxidation process treating 3000 stpd in three four compartment horizontal autoclaves 14' diameter and 53' long. Since the initiation of autoclaves for the treatment of gold bearing sulphides, there are presently 16 gold autoclaves operating worldwide varying in size up to 18'4"" inside diameter. There are seven autoclaves for the treatment of refractory sulphide gold bearing ores to be commissioned in 1997 and 1998.Autoclave technology has progressed extensively since the mid-eighties. Operational experience has made rapid progress and the result is much smoother and safer autoclave operation. There have been many advances in autoclave technology design. For example, the use of exotic materials for corrosion resistance to reduce down time for maintenance. The instrumentation involved in autoclave operation is very sophisticated which allows for many safety features. The advanced design has allowed for greater availability and as a result operating costs and maintenance costs have decreased. These technological advancements have made autoclave technology more safe and this has resulted in a greater acceptance of this type of operation. Many of the gold autoclave facilities operate up to 9 months continuously without shutdowns. The advancement of autoclave technology has inspired many new applications.Because of the outstanding operation of autoclaves in the gold industry, many other applications for autoclave technology are being considered. The following is a list of autoclave applications:"

Jan 1, 1997

By Andrew R. Marchbank

The application of biologically assisted methods for metal extraction in the mining industry has a long history, but development of modern techniques has been relatively slow. There is, however, a resurgence of interest in the industry with the recent development of methods to successfully treat base metals concentrates. Two major pilot plant programs for treatment of chalcopyrite concentrates have been initiated in the past year and results from one are beginning to be released. This paper provides an overview of methods that have been applied in the past; from the earliest deliberate applications of the technology, through the copper and uranium heap and dump leach applications, the more highly engineered agitated tank leach gold applications and the developments currently taking place in the industry.

May 1, 2002

By George F. Crocker

Introduction The Helen mine and the Victoria mine of Algoma Ore Properties, Limited, in the Michipicoten district, Ontario, are 120 miles north of Sault Ste. Marie, on the north shore of lake Superior. They are on the Algoma Central railway between Hawk Junction and Michipicoten Harbour. Between them, these mines have produced 10,757,113 tons of iron ore. From 1900 to 1918, 2,823,369 gross tons of brown ore was shipped, and from 1939 to the end of 1949, 7,933,744 tons of siderite was produced from the open-pit operations and underground development. The finished product, known as 'Algoma sinter', is shipped to blast furnaces both in Canada and the United States. The iron-ore bodies are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 feet and has maximum width of 1,000 feet. The two siderite orebodies, known as the Helen and Victoria, are separated by two diabase dykes. The Helen orebody is 1,600 feet long with a maximum width of 250 feet and the Victoria is 1,200 feet long with a width comparable to the Helen. These orebodies are considered to be a replacement of the original rock by iron carbonate. The introduction of the iron-1bearing material probably occurred after the development of the major folded structures. The open-pit mining of siderite started in the Helen ore body in 1939 and continued until 1945. During this period, 3,853,395 tons of ore was mined. Open-pit mining started in the Victoria body in 1946 and is still being carried on. Underground development commenced in September, 1947. Diamond drilling and surface sampling had shown the Helen deposit to average 35.61 per cent Fe and 7.28 per cent SiO2, and the Vi.otoria deposit 33.73 per cent Fe and 10347 per cent SiO2?

Jan 1, 1950