Search Documents

By Henry Lloyd Smyth

In 1891-92 1 was entrusted with the geological survey of part of the large area lying between the Marquette and Menominee iron-ranges in the Upper Peninsula of Michigan, and extending from the Republic trough on the north, through portions of the valleys of the Michigamme and Fence rivers, to and including the intermediate Felch mountain range on the south. Until a few years back the larger part of this area has been very difficult of access, and much of it is difficult still. The rock-surface is for the most part covered with swamp, forest and glacial deposits of various kinds, and therefore has not invited geological study. For these reasons the district, as a whole, with the exception of the Felch mountain range, remained almost unknown from a geological standpoint until our work in 1892. Our main object was to map the pre-Cambrian rocks, particularly the iron-bearing formations of Algonkian or Huronian age, and to obtain as much information as possible with reference to their sequence and structure, In carrying out this purpose, the use of simple magnetic instruments was found to be of the greatest assistance, and indeed indispensable. In this paper the results of our experience in tracing magnetic rocks by means of the disturbances produced in these instruments, have been brought together in systematic form, with such references to the particular area as are necessary in order to illustrate general principles, with the hope that they will prove useful to other workers in the same region, or in other regions where similar conditions may be encountered. The writer was efficiently aided in the field-work by Messrs. Samuel Sanford and Charlea N. Fairchild for nearly the whole period, and E. B. Mathews and H. F. Phillips for part of it,

Jan 1, 1897

By A. Lubinski, C. R. Stewart, K. A. Blenkarn

Storage porosity has been considered one of the important pore geometry characteristics of heterogeneous-porosity limestones. Storage pores are only containers for fluids, in contrast to flow channel pores which both contain fluids and provide continuity for fluid flow. The concept of another geometry characteristic, "poro-striction", is presented as a second pertinent variable in describing limestone pore space. In simple terms, poro-striction is a measure of the flow resistance between storage and flow channel pores. Alternating-flow core-testing theory provides flow relationships which can be used to divide the pore space of heterogeneous-porosity media into flow channel and storage pores and to measure the "porostriction" of the latter. Experimental application of this theory to naturally occurring heterogeneous limestones shows that "porostriction" and the ratio of storage to flow channel pores can be estimated. Porostriction and porosity ratio are microscopic characteristics which should influence oil-recovery efficiencies during certain types of displacement processes. A knowledge of pore geometry should be valuable in designing or selecting the most effective oil-recovery process for heterogeneous limestones containing storage porosity. INTRODUCTION The primary and secondary recovery of oil from limestone (carbonate) reservoirs has been and will continue to be a major source of the world's supply of petroleum. Oil recovery from this type of formation is strongly influenced by the size, shape and arrangement of the pore spaces which hold the formation fluids. Therefore, it is expected that better knowledge of pore geometry would lead to design of more effective recovery processes. The concept of storage and flow channel pores has been presented as an important characteristic of limestone porosity.1 In this concept, storage pores are only containers for fluids, whereas flow channel pores are those pores which both contain and transmit the fluids. The work reported herein involves the concept of an additional pore characteristic called "porostriction". This characteristic can be visualized as the flow resistance between the storage and flow channel pores. This resistance is an important pore geometry characteristic because it determines how easily gas and oil can replenish fluids removed from the flow channel pores. Fatt and co-workers at the U. of California have studied the effect of storage porosity and a factor similar to porostriction on transient-flow response of models of porous media during a pressure build-up or drawdown test.55 These models consisted of porous sandstone cores with artificially simulated storage pores. It is the purpose of this paper to describe tests which permit the storage porosity and porostriction of actual reservoir core samples to be estimated. The tests used for this purpose involved not transient tests but, rather, an alternating-flow technique in which pressure and flow are varied according to a sine-wave relationship. This technique may offer advantages over transient methods. THE POROSTRICTION CONCEPT Before discussing alternating-flow (A.F.) tests in core samples, it is necessary to define the porostriction parameter. For this purpose attention is focused upon an elemental volume v representative of a porous medium having both flow channel pores and restricted-access storage pores. For such an elemental volume, it is considered that the storage porosity is combined to form a single pore and that the access into the storage porosity may be represented by a single capillary tube connecting the single pore to the flow channels of the elemental volume. Let the radius of the capillary tube be designated as Rc and its length as L,. When fluid flows into or out of the pore, the following equation (Poiseuille's law) relates flow rate q to pressure drop p, and the physical characteristics of the tube and the fluid of viscosity jx.

By W. F. Wheeler

IN the study of the coals of Illinois now being carried on by the State Geological Survey, an attempt is being made to determine the most satisfactory basis of comparison between different coals. The following discussion is based upon work done for the survey in the laboratories of the State University and under the general direction of Prof. S. W. Parr. " Pure coal " has been defined by Mr. A. Bement1 as ash- and moisture-free coal, and the use of this " pure coal " as a basis for comparing different bituminous coals has lately been much discussed among engineers in the middle West. By some the B.t.u. of the pure coal is being used to check calorimetric results, and to calculate the calorific value of different coal-samples from the same seam, for which purposes it is necessary to assume-first, that the composition and calorific value of pure coal from different parts of the same coal-seam are uniform, and, second, that these values remain constant after the coal is mined, both of which assumptions there are reasons to believe are inconsistent with the facts. Certain variables are included in pure coal, as ordinarily defined, and disregard of them may lead to serious error. In any event, where delicate shades of difference are involved, no sure interpretation of results can be made, unless these variables be eliminated. As a basis of comparison between coals, ash- and moisture-free coal is much to be preferred to " dry coal," and still more is it to be preferred to " moist coal," as ordinarily reported in analyses. There are, however, two constituents other than ash and moisture which are similar in effect to them, and which

Jan 1, 1908

By W. L. Saunders

(Wilkes-Barre Meeting, June, 1911.) I. INTRODUCTION. IT is now generally admitted by experts that at least so far as rapid progress is concerned the Alpine system of tunnel-driving is superior to any other. This is perhaps natural in view of the record of experience in driving tunnels through the Alps. These great mountain-chains cannot be treated in the ordinary way by shaft-sinking and driving headings, thus multiplying the points of attack. The work must be done from the ends only, hence speed in driving is of the utmost importance; and, as necessity is the mother of invention, the concentration of effort to make progress has resulted in an organization and in mechanical appliances that have produced results so much in excess of the usual practice, even in America, that a discussion of the subject in detail should be of much value to the engineer and contractor. The first Alpine tunnel was the Mont Cenis, length 7.5 miles, driven with a progress that averaged about 7.75 ft. per day. Next came the Saint Gothard, 9.5 miles long, 18 ft. per day; Arlberg, 6.5 miles long, 27.25 ft. per day; Simplon, 12.25 miles long, 36 ft. per day. The figures represent progress when driving from two headings, so that by dividing them in two we get the daily single-heading progress. The latest of the Alpine tunnels is the Loetschberg, now being driven. In this work the world's record has been beaten by a single day's record in one heading of 36 ft. and by an average daily record in. one heading of 29.5 feet. The Alpine range forms a natural barrier between a large section of northern and southern Europe. This range extends from the southeast of France to the frontier of Hungary, between Italy and the plains of southern Germany. The contour

Jul 1, 1911

By Albert J. Phillips

The effect of impurities on the flowsheet in the smelting and refining circuits for copper, lead and zinc is reviewed and the interflow of by-poduct metals from copper, lead and zinc plants is pointed out. The principal points of separation of all impurities in the circuits are indicated and the additional steps added to these circuits in order to effect impurity separation me shown. In this day and age, when difficult metallurgy is mentioned, one thinks of the extraction of more refractory or possibly the alkaline earth or rare-earth metals. It is true that the extraction of metals having a high affinity for oxygen and deleterious solubility for that element in the liquid metal, affords some of the most difficult extractive metallurgy problems. When this is coupled with an affinity for hydrogen, nitrogen, and carbon a devious approach is required that sometimes rivals the complexity of the metallurgy with which this paper deals. However, in all such cases the aim is for a simple

Jan 1, 1962

By C. R. Kuzell

IN COMPARISON with recent years 1932 has yielded much less tangible evidence of progress in copper reduction and refining. The industry has been extremely quiet, especially in the United States. Design and construction has been throttled by lack of new capital expenditures. The excess producing capacity of the whole industry and the extremely gloomy outlook for the future have made it unwise to tie up more capital except under special conditions. The plants built during the previous year have, however, been placed in operation. Older plants have been abandoned, temporarily shut down, placed on part time operating basis, or continue to operate at a low percentage of normal capacity. In the United States the Phelps Dodge Corporation at Douglas, Ariz., has completed the remodeling of the former Calumet & Arizona smelter. A new roaster and Cottrell plant chimney was completed this year. Though operations have been limited the new equipment has been found to justify all expectations. The reverberatory plant addition consists of two furnaces 26 by 107 ft. inside dimensions, with a high arch, and modern steel binding of excellent design. Natural gas fuel gives good results. One of these furnaces will treat 1000 tons of solid charge per day with a fuel consumption of approximately 3,000,000 B.t.u. per ton. The larger converters have not only yielded the expected lower costs, but have simplified operations in the converter department. One of the noticeable results is the greater cleanliness in the environment and the absence

Jan 1, 1933

By R. E. Allen, A. C. Jephson

ELECTROLYTIC zinc plants of the American Smelting and Refining Co. are located adjacent to the present city limits of Corpus Christi, Texas. The original plant commenced operations during 1942, and is designed for the production of special high grade zinc from zinc sulfide concentrates.' Subsequent changes include the erection of an additional acid plant during 1950, and additions for increased generating and production capacity during 1951. New Electrolytic Plant—The new electrolytic plant is a separate unit erected for the treatment of densified fume produced at Asarco plants located in El Paso, Texas and Chihuahua, Mexico. Construction was completed and operation commenced during June, 1953. Decision for the erection of a separate plant for the treatment of densified fume is based on several factors. One of the principal reasons is the assurance of continued production rate of the original plant, which might have been jeopardized by combined treatment of calcine and fume. Of equal importance is the advantage of locating a plant on a site with adequate space for eventual expansion. General Description—The new plant for the treatment of densified fume consists of four main buildings for the following operations: storage and grinding of fume, leaching and purification, electrolyzing and casting, and rectifier units. Auxiliary buildings include a baghouse, reagent storage, and a lunch room. Leaching of ground fume with electrolyte from the cells is a batch type operation in tanks equipped with mechanical agitators and weightometers. Completed leaches are pressure filtered, the resultant residue being recovered for shipment to El Paso by conventional use of thickeners, drum type vacuum filters, and a direct-fired dryer. Filtrates from the filter section are purified in mechanically agitated tanks, filtered after completion through plate and frame presses, and then pumped to an evaporative type cooling tower. Solution discharged from the basin of the cooling tower is collected in storage tanks for use in the cells. The cool purified solutions are pumped as required from storage to the solution circuit for circulation of electrolyte through the cells. Except for the addition of purified feed solution and withdrawal of electrolyte for leaching, the circulating system for the cells is essentially a closed continuous circuit that includes the use of evaporative cooling towers for control of solution temperatures. Aluminum cathodes and Ag-Pb anodes are used for electrolysis, which is maintained at a current density of about 82 amp per sq ft. Cathode zinc produced is melted in a gas-fired reverberatory furnace and then cast into slabs on a straight line casting machine. Unloading and Storage—Fume produced by the Chihuahua plant is shipped in box cars, and fume by the El Paso plant in hopper bottom dump cars. Shipments as received are weighed on a 7 5-ton capacity railroad scale, sampled, and then moved over one of the two unloading hoppers with a car puller. The cars are then unloaded with mechanized equipment, a car scoop being used for unloading of box cars and a car shaker for the hopper bottom cars

Jan 1, 1958

?AARONSON, ALFRED E, .Vice-Pres, Mid-Co Petroleum Co , Mid-Co Bldg, Tulsa, Okla '18 ABADIE, EMILE R, Min Engr - Box 927, Porterville, Cal '76 ||ABADILLA, QuiRiCo A, Student, Colorado School of Mines, Golden, Colo. '20 ABBOTT, CLARENCE E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co , 1405 Minnesota Ave, Bessemer, Ala. '04 ABBOTT, Louis BENJAMIN, Chief Engr, Consolidation Coal Co-, Elkhorn Div, Jenkins, Ky '15 ABBOTT, ROBERT R Met. Engr, Peerless Motor Car Co, Cleveland, Ohio. '12 ABE, ASAKA Fujita Min Co, Dojima, Osaka, Japan '14 ABEEL, GEORGE H, JR, Cons Min Engr, 633 St Paul Ave, Los Angeles, Cal '18 ABEL, ALBERT E, Mgr., Pittsburgh Dist, Valley Mould & Iron Corpn, 28th St & R R Ave, Pittsburgh, Pa '19 ABEL, W D, Min. Engr. 3897 Sacramento St , San Francisco, Cal. '19 ABELL, 0 J, Pres & Treas, Abell-Howe Co, 332 South Michigan Ave, Chicago, Ill '19 ABERNATHY, G E Willow Springs, Mo '20 ABEY, HIROSHI, Min & Met Engr, Arakawa Mine, Mitsubishi Co, Senpoku-gun, Akitaken, Japan '17

Jan 1, 1923

By E. R. Johnson

THE copper concentrator of the Braden Copper Co. is at Sewell, Chile, on the western flank of the main Cordillera of the Andes, at an air distance of approximately 50 miles southeast of Santiago, the capital of Chile. The region is mountainous and space is at a premium because of the rough terrain and the danger of snowslides. The ore, a porphyry copper, is mined by a block-caving method in the El Teniente mine. It is hauled to the crushing plant, a distance of 2.6 miles, through a tunnel because of the severe climatic conditions. The usual large, coarsely set, primary reduction machines found in many ore-treating plants are not required because of the mining method employed and the limiting 12-in. spacing of the grizzlies at the head of each ore pass in the mine. It is the purpose of this paper to describe the numerous improvements made in the crushing section of this large flotation concentrator during the past 15 years to increase the efficiency of the plant and to raise the daily output from around 20,000 to 30,000 tons. The reader should keep in mind that all changes were made within the existing building because of the limited space and the high cost of the heavy mill construction required to withstand the snow loads. The present plant, as well as the former, operates on a 24-hr, 7 days a week basis. FORMER PLANT The crushing plant commenced operations at its present site in 1921, the main equipment being No. 7 1/2 gyratories, followed by 48-in. horizontal Symons disk crushers. Fines were removed by 1-in. stationary grizzlies ahead of each unit. In 1924 a third stage of crushing was provided by the addition of 55 1/2-in. rolls in open circuit. During 1925, the Symons disks were replaced by 73 1/2-in. rolls. All the rolls were changed to closed circuit, with elevators and screens to give a final product of 9 pct plus 3-mesh. The flowsheet of a typical crushing section of this period is shown in Fig I. The ore was withdrawn from a common bin serving the five crushing sections in the plant by means of any number up to six 36-in. wide-apron feeders, which discharged onto a common conveyor belt. This conveyor was equipped with a magnetic head pulley and the crusher attendant was stationed near the discharge end to pick out pieces of mine timber that might be in the ore. The ore was discharged over a 1 3/4-in. spaced bar grizzly and the oversize of this grizzly was crushed by a No. 7 1/2 McCully gyratory crusher set at 1 3/4-in. opening on the closed side. The grizzly undersize joined the gyratory discharge and was conveyed to a set of 73 1/2 by 20-in. Garfield rolls set at I in. These rolls operated in closed circuit with a bucket elevator and two vibrating screens placed in parallel.

Jan 1, 1947

By C. W. Chen

MARTENSITE transformations in ß Cu-Al alloys have been studied by Greninger1 and other investigators. According to Greninger, the parent phase ß1 an ordered body-centered-cubic structure obtained from ß phase by suppressing the eutectoid decomposition, transforms into an ordered hexagonal-close-packed phase in composition containing 12.9 to 14.7 pct Al. The M, temperature decreases with increasing aluminum content; for the alloy containing 14.5 pct Al, for example, the ß1??' transformation occurs below room temperature. More recently, Kurjumow2 studied the transformation in ß Cu-Al alloys with the addition of nickel. His report stimulated new interest in the subject due to the observation of completely reversible transformation without hysteresis in the transformation temperature ranging from 10° to —10°C. In the present paper some characteristics are described of the transformation of Cu-Al-Ni alloys that were partly studied by Kurjumow. Experimental Procedure High purity copper (99.999 pct) and aluminum (99.99 pct) and electrolytic nickel were used in the preparation, by the Bridgman technique, of single crystal specimens which contained aluminum and nickel of 14.5 and 0.5 to 3.0 pct, respectively. Polished surfaces were prepared mechanically. Specimens were then chemically etched to remove distorted material, homogenized at 1000°C for several hours, and quenched drastically to room temperature in a 10 pct NaOH bath to produce the parent phase ß1. The transformation was studied under a microscope and, in some cases, recorded by means of motion pictures. A device similar to that designed by Greninger and Mooradian3 was used to cool and reheat the specimens. Results and Discussion When the specimens were cooled below room temperature, the ß1 to ?' transformation began at 10°C with the appearance of ?' crystals In relief, Fig. la. As the specimen temperature dropped further, the transformation continued, either by the growth of the ?' crystals, with the ß1 — ?' interface moving into the ß1 phase, Fig. 1c and 1d, or by the formation of new ?' crystals, Fig. 1b. As a consequence of the former process, banded structure is observed as a common feature of the low temperature phase. According to the theory of the formation of martensite by Wechsler, Lieberman, and Read,' the bands of ?' phase are probably twin-related, as is the case in the diffusionless phase change of In-T1 alloys,5 but this was not revealed by X-ray tech- niques. New ?' crystals, in needle form, often emerged suddenly across the ?' bands during the transformation. These acicular crystals then grew, both in length and in width, see Fig. 2a through 2d. The transformation on cooling is completed at about -35°C. Upon heating, the reverse transformation started at —10° C, in a manner nearly opposite to the transformation on cooling, and completed at 35°C. There was no noticeable change in the transformation temperature when the nickel content was varied within the limits previously mentioned. Through control of the specimen temperature, the transformation can be started, stopped, or reversed at will. This phenomenon has frequently been observed in the martensite transformation of many nonferrous alloy systems. Other systems are Au-Cd6 and In-Tl.5 ow-- ever, in the latter systems, the transformation is accomplished by single interface motion if the specimen composition is homogeneous and the temperature gradient in the specimen is uniform and sharp, whereas in the Cu-Al-Ni specimens, only multiple interface transformation is observed. The speed of the interface motion appears to be a functionof the rate of temperature change and the temperature gradient across the specimen length. In one case, in which the temperature increased at the rate of 10°C per min and there was no temperature gradient along the specimen axis, the speed of the disappearance of a ?' plate was determined, by the study of the motion pictures made, to be 26 µ per sec. Quench markings were observed on the polished surfaces of specimens. The markings were grouped into one or more sets of different orientations, and were parallel in each set. The ?' plates formed in subsequent transformation were parallel to the markings, indicating that the ?' plates and the quench markings had the same geometric relation-ship to the ß1 matrix. The quench markings on two intersecting surfaces of a specimen were therefore used in the determination of the habit plane of transformation, by the trace method suggested by Barrett.' Results obtained from five sets of markings in three specimens indicate that the habit plane is an irrational plane about 2" from one of the {221} planes. This is very close to the habit plane (3" from 221 planes) of ß Cu-Al alloys containing more than 13.0 pct Al.1 The martensite transformation of Cu-Al-Ni alloys is reproducible. No sluggishness was found between consecutive transformation cycles, although a slight difference in the distribution pattern of the ?' plates was observed, compare Figs. Id and 2d. The transformation can be strain-induced. This characteristic has been tested by a simple method. When a specimen was elastically strained slowly in a vise, ?' plates were gradually produced in the same fashion as during transformation on cooling, This test was done at room temperature, and thus above the M,

Jan 1, 1958

Jan 1, 1887

O. S. GARRETSON, Buffalo, N. Y.: If I may judge from the half-tone illustration engraved from a photograph of this medal and accompanying Dr. Prazer's paper, I do not think the cast ing is exceptionally fine. I have often made castings of simi lar character which I think were equally good. For instance, I have taken a coin, moulded it directly in fine sand, and cast from it in Scotch (or the equally good, if not better, Ameri can Scotch ") foundry-iron a copy quite as sharp and smooth as the original. The secret is in using very fine sifted sand. In fact, I have used for this purpose the dust which had accumulated on the beams overhead in my foundry, riddling it with a very fine sieve before using it. ['NOTE BY THE SECRETARY.—After the session at which these remarks were made by him, Mr. Garretson cast at his Buffalo foundry, in the presence of a number of members of the Institute, copies of the bronze pin furnished to visiting members by the Local Committee of the Buffalo meeting. The accom panying illustration, Fig. I, has been reproduced from a photograph of such a casting, made in green sand, under the conditions of ordinary foundry-practice, and not subsequently polished in any .way. I can also certify that the photo graphic negative was not touched, to improve its clearness of definition, before the production of the " half-tone" plate from which Fig. 1 has been printed. As, in the case of the Kytchtym medal, it was the thin, ribbon-like sprue, rather than the low-relief features of the medal itself, which indicated the fluidity of the metal and the sharpness of the casting, so in this work of Mr. Garretson it is the long and slender pin which offers the strongest evidence of these qualities. It is scarcely neccssary to point out that the filling in the mould of a long and nar row opening, such as this pin presents, is the severest test that could be imposed upon the casting, and that the sharpness of the point of the pin in the casting is striking evidence of the success with which this test has been met. The Pittsburgh Testing Laboratory .has made for the American Manufacturer measurements of this casting and an analysis of the sprue. The thickness of the main casting is from 0.049 to 0.068 inch. That of the tag bearing the stamped number is 0.024 inch. The analysis, which represents the iron ordinarily employed by Mr. Garretson for thin castings, is as follows :

Jan 1, 1899

By R. E. Fryxell, E. C. Duderstadt, P. K. Conn

Permeation rates for nitrogen through are-cast tungsten were measured in the temperature range 1800° to 2600°C at nitrogen pressure differentials of 1.0 and 0.1 atm. Gas chromatography was used to measure the quantities of nitrogen which permeated through 0.26-and 0.53-mm-thick membranes. Permeation rates were proportional to the difference between the square roots of the nitrogen pressure on each side of the membrane and inversely proportional to membrane thickness, indicating that atomic nitrogen was the difjusing species and that diffusion was the rate-limiting step of the process. Permeation coefficients calculated from the rates may be represented by the equation: where P is expressed in the units cu cm (stP)-mm per 1/2 sq cm-min-atm"' and 70.0 * 0.8 is the activation energy in kcal per mole of permeating species. In a previous paper' permeation rates were reported for hydrogen and for oxygen through tungsten. The permeation cells used for the hydrogen measurements were suitable for measuring nitrogen permeation under similar conditions, so the study was extended to include nitrogen. Permeation rates of nitrogen through the polycrys-talline arc-cast tungsten membranes were measured in the temperature range 1800" to 2600°C using two membrane thicknesses and two nitrogen pressure differentials. Permeation coefficients were calculated and the activation energy of the process determined. THEORY For diatomic gases which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at an elevated temperature where bulk diffusion is the rate-limiting step of the process is given by the equation: where: q = total amount of gas permeating a membrane, P = temperature-dependent permeation coefficient, A = area of membrane, t = time, p1 = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, and d = thickness of membrane. When bulk diffusion is the rate-controlling step, and the solubility of the gas obeys Henry's law, a further relationship is that, for any given temperature and pressure, the permeation is the product of diffusivity and the amount in solution. The permeation coefficient, P, is temperature-dependent according to the equation: where: Po = permeation constant, Q = activation energy, R = gas constant, and T = absolute temperature. EXPERIMENTAL PROCEDURES Cell Design and Experimental Apparatus. Two of the permeation cells used for the previous measurements of hydrogen permeation are shown in Fig. 1. Each consisted of a cylindrical chamber divided into two parts by a permeation membrane fabricated from high-purity (>99.9 pct W) wrought tungsten sheet made from vacuum arc-cast tungsten. The membrane in one cell was 0.26 mm thick and the other was 0.53 mm. The fabrication of these cells was described previously.' The permeation cells were mounted vertically in a high-temperature tungsten resistance furnace and the membranes and the center portions heated to test temperatures. Temperatures were measured by sighting an optical pyrometer on the edge of the membrane through a small hole in a tungsten plate which was fastened to the side of the cell. This arrangement provided an approximate black-body condition and eliminated the need for emittance corrections. Appropriate corrections were made for the quartz window through which the temperatures were measured. Argon gas flowed through the 10-liter volume of the furnace at the rate of 4.7 liters per min. An impurity

Jan 1, 1969

By Roy P. Full, Robert M. Grantham

Regional structural adjustments in early Tertiary time resulted in the development of the Republic graben, a major down-dropped block that is from 6 to 10 miles in width and more than fifty miles in length. The graben became the center of extensive volcanic activity during Eocene and Oligocene time, resulting in a thick sequence of water-laid tuffaceous sediments, volcanic flows, and associated intrusives. A younger series of sediments, pyroclastics, and flows were deposited in structural depressions within the graben following the period of widespread volcanic activity. The Republic mining district is located along one of the major intragraben structural zones, where continuing subsidence during the period of volcanic activity resulted in an increased thickness of flows and associated flow breccias and pyroclastics. Intrusive masses in part healed early graben-forming faults, but later subsidence reopened old faults and created new fracture zones which later became the control for the gold-quartz veins. Considerable block adjustment along the subsidence area is evidenced by the structural pattern in the mines, and telescoped vein structures indicate north-south compressional stresses and east-west graben-forming tensional stresses prior to and during the emplacement of the veins. The veins, varying from a few feet to more than 50 feet in width, are filled primarily by fine-grained quartz, commonly chalcedonic or porcelain-like in appearance. Finely laminated dark-gray to black concentric banding within the veins generally distinguishes the better-grade ore zones, which contain finely disseminated sulfides and ore minerals that include principally electrum, stephanite, naumannite, and native silver.

Jan 1, 1968

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By N. Tiner

The mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed com-rnercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques,1"4 and Achenbach, Nippcr and Piwowarsky,% ased principally on thermal analysis, ascribe the grain-refilling action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the cffect of superheating on grain size of magilesium alloys. .ittempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. Thc preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. Preparation of Samples and Grain-size TestiNg The alloys investigated in this paper were taken from ingots made by Permanente the Or or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1946

By C.P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By C. P. Clingerman

The recent iastallation of a combination dust catcher, gas washer and precipitator at Carrie blast furnaces of the Homestead Steel Works has given very satisfactory results. The following description of the gas-cleaning installation is based on actual operating experience. When Carrie blast furnace No. 3 was rebuilt the decision was made to fine-clean all the gas produced by the furnace, because the management wanted fine-cleaned gas for fuel in the stoves and boilers. In order to keep the installation cost as low as possible, the gas-cleaning system was streamlined. All by-pass lines and goggle valves for bypass lines were eliminated from the system. A radical departure from the use of 8-in. tubes in the Cottrell-type precipitators was made by using 12-in. diameter tubes in a single compartment, the single compartment being divided into two units by a single partition wall in the top header. The Furnace Proper A few of the characteristic points and dimensions of the furnace proper are: Hearth diameter.............. 26 ft. o in. Bosh diameter............... 29 ft. 1 3/4 in. Stock-line diameter........... 20 ft. o in. Large-bell diameter........... 14 ft. 8 in. Small-bell diameter........... 6 ft. 6 in. Height of furnace from center of iron notch to bottom of large bell, closed............ 94 ft. 4 in. Height of furnace from center of iron notch to main platform ...................... 105 ft. o in. The furnace top is equipped with a MC-Kee revolving distributor, the operation of which is electrically interlocked with the skips, bell hoists, and coke-weighing and charging apparatus through a Freyn automatic charging control. The gas leaves the furnace first through four offtakes, 5 ft. 9 in. in diameter, then through uptakes that, are approximately 85 ft. high, which feed into a single down-comer that is 9 ft. in diameter. Dust Catcher The primary dust catcher installed (Fig. I) may be described as a single-cone type. The inlet pipe at the top of the dust catchei is 9 ft. in diameter; it is flared to a conical shape as it extends down inside the dust-catcher shell, which is 35 ft. in diameter, 37 ft. high on the straight side, and has a conical top and bottom. The slope of the bottom is so0 with the horizontal. The cone-shaped pipe inside the dust-catcher shell is 42 ft. high and is 19 ft. 7 in. in diameter at its bottom lip where it releases the gas inside the dust catcher. The ratio of the area of the inside cone at its bottom lip to the

Jan 1, 1943

By Richard Paul Seelig

The following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. 'The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which mag stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. 'The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. Inasmuch as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a com-pressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Although these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself," alls attention to the fact that the properties

Jan 1, 1947

By Richard Paul Seelig

The following review covers published information on pressing of metal powders at room temperature. Only those operations are considered which occur between the time the powder is filled into the cavity and the compact is ejected from the die. Thus, this review does not concern hot pressing, coining or sizing feed or flow problems, commercial presses nor designs. It was also necessary to disregard to a large extent the effect of pressing on subsequent operations and on properties after sintering. 'The pressing operation is considered independently in its function to compact loose metal powder into useful shapes which can subsequently be handled. There are some comments by the writer in connection with a few of the findings quoted in the literature in order to stimulate thought and discussion. The selection of references quoted in the text is in some cases arbitrary although an attempt was made to favor papers containing novel ideas, techniques or results which mag stimulate future research. In order to enable the reader to check further into the subjects mentioned, the original, rather extensive, bibliography is appended even though not all the references are touched on in the printed version of this review. The equipment used by various workers, for example a die design created by Bridgman,22 is very interesting. 'The die insert has a conical external surface. The vertical pressure exerted on the punch transmits itself to the die which in turn is pushed harder into its tapered retainer. Thus, the higher the pressure exerted on the punch, the higher also the pressure exerted inwards on the die inserts. Inasmuch as this pressure counteracts the internal pressure from the compact the two stresses balance each other so that it is possible to obtain tremendous pressures without breaking the die. The die collar was made from an oil hardening tool steel, heat treated to a tensile strength of some 300,000 psi. The die was closed at the bottom by a plug made from special tool steels. Bridgman found that there is no steel which will withstand a com-pressive stress of 700,000 psi without continuous slow flow or immediate fracture. Therefore, the only material suitable for use in the pressing punch was sintered carbide. In view of the ingenious design it was possible to use special tool steel as die material. Jones22 raises the question whether this method of pressing has practical application in powder metallurgy. Although these tremendous pressures cannot readily be utilized without many special precautions, the tapered die and retainer idea is believed to be useful even for lower pressures. Bridgman, himself," alls attention to the fact that the properties

Jan 1, 1947