Search Documents

By R. F. Mehl, C. S. Barrett, A. G. Guy

INTRODUCTION IN the last few years this laboratory has published a series of papers on the mecha¬nism of age -hardening.14,1,6,11,20 Briefly stated it has been proposed that hardening is caused by lattice strains created by lat¬tice coherency between matrix and precipi¬tate; much experimental evidence has been advanced to support this thesis. The system Cu-Be is an attractive one to study. It is a system that exhibits marked age hardening; it ought to be subject to the type of analysis of structural changes hitherto explored and it is a prominent example of "discontinuous precipitation," which, though studied in other cases, 6,20 remains largely unexplained. This research shows that hardening in the Cu-Be system proceeds essentially as proposed earlier.14 Guinier-Preston zones have been observed to form on the {100) planes of the matrix; no transition lattice was found. Aging and overaging were ob¬served to occur most rapidly in the region of discontinuous precipitation-the grain boundary-apparently accelerated there by strain. The Constitution of the Cu-Be System The Cu-Be constitution diagram is shown in Fig I. The structure of the ? phase was determined by Misch16 as of the caesium-chloride type with a lattice con¬stant of 2.598 Å High temperature X ray photograms of 7.2 pct Be alloy made by Kossolapow and Trapesnikow13 led them to conclude that the structure of the P phase is simply disordered body-centered cubic with [ao] = 2.79 Å at 750°C. Previous Work The initial work on the age-hardening of Cu-Be alloys was that of Masing, Dahl, Holm, and Haase. Their numerous papers were published in book form in 1929, sub¬sequently translated.18 The effects of Be content, solution temperature, aging tem¬perature, and cold work on the hardness developed in these alloys were studied. An initial decrease in the electrical conduc¬tivity was observed when strips of a 2.5 pct Be alloy were aged at temperatures from 200 to 350°C; a wire of the same analysis failed to exhibit this decrease when aged at 350°C. A volume decrease of 0.6 pct oc¬curred during aging at 250°C. Microscopic investigations of quenched and aged alloys disclosed a regularly ori¬ented "striping" (ripples) on the a and on the ß grains. In the case of the ß the cause of the striping was held to be decomposition

Jan 1, 1948

By R. B. BRINSJIADE

THE following is an attempt to form a formula by which a mine call be quickly evaluated, after all pertinent physical data have been collected from observations on the ground by a competent mining engineer. ASSUMPTIONS. Let G = price to be paid for the mining property. M = cost of developing the mining property to yield y tons of ore daily. P = cost of suitable plant to treat y tons of ore daily. p = value of said plant when the mine has.been exhausted. C = total fixed capital investment. W = working capital investment

Jan 1, 1908

By J. T. Crawford

Although nearly 10 pct of the total tonnage of coal produced annually within the United States is handled by bulk freighters on the Great Lakes, very little of the detail connected with it has been published other than occasional newspaper stories and publication of tonnage statistics. Of the total tonnage floated on the Lakes each year some 10,000,000 is stored and distributed from the port of Duluth-Superior, at the western end of Lake Superior commonly known as the Head of the Lakes. This port has the largest single area concentration of coal docks in the world. Since this area contains the largest ore docks, the largest movable material handling bridge, the largest and highest grain elevator and the largest coal bri-quetting plant in the world, it is entirely fitting and proper that here also should be located the largest coal dock and what we believe to be the world's largest clam shell. Of the sixteen coal docks operated by ten companies, five are owned and operated by the North Western-Hanna Fuel Co. which has two docks on the Superior, Wis., waterfront and three docks in Duluth, Minn. It is with these five docks that we are primarily concerned, General History In the summer of 1871 a small sailing vessel entered the harbor of Duluth-Superior with the first commercial coal cargo. All the coal brought up that first year did not amount to more than 3000 tons. During the year 1877 the first dock equipped for handling coal was built in Duluth. Coal receipts increased to 52,785 tons in 1879 the first year for which an official record was kept. Since then the volume of water-borne coal to the Head of the Lakes steadily increased to a maximum of 12,688,321 tons in the year 1923. This tonnage was nearly equalled in the year 1927 and the next highest tonnage recent year was in 1946 when 10,105,703 tons were unloaded. The average annual bring-up over a ten year period 1938 to 1947 was 8,605,231 tons. Approximately 30 pct of the coal unloaded at the Head of the Lakes is handled over the docks of the North Western-Hanna Fuel Co. Competition of other fuels coupled with expansion of coal fields in the mid-west have held coal receipts for Duluth-Superior at a relatively constant figure during the last eight years although the total tonnage of coal floated on the Great Lakes has more than doubled in the past 25 years. From the shovel and wheelbarrow method of unloading early cargoes to the horsepowered windlass derrick with a wooden tub was but a short step. The first movable coal handling, steam operated,

Jan 1, 1949

By C. F. Jenkins, G. V. Smith

Serrated plastic flow in stable austenitic alloys based on Fe/Ni has been shown to be related to the presence of carbon and/or chromium in the systems. Strength peaks and plateaus in the serrated-flow temperature region for a commercial alloy correlate with an increased dislocation content, arising, presumably, from enhanced multiplication as a result of a strong interaction between dislocations and solute atoms. The data generally support a mechanism controlled by migration of vacancies, with the energy for vacancy motion being modified by the presence of chromium. Chromium atom -dislocation interaction is responsible for effects above 500°C, whereas the defect interacting with dislocations between 200" and 500°C is suggested to be a carbon-vacancy Pair. ThE phenomenon of jerky flow, serrated flow, or the Portevin-le Chatelier (P-C) effect in austenitic stainless steels is usually attributed to substitutional at1,2 mospheres1,2 or to precipitates&apos;-4 which form at dislocations during plastic deformation. On the other hand, evidence exists which supports a direct inter-stitial-dislocation interaction mechanism for serrated flow in fcc Ni-C,5,6 Ni-H7-9 and in nickel-austenites containing carbon." The present work consists in a study of serrated plastic flow in stable austenitic al-loys. The effects of carbon and of chromium were investigated separately, and a commercial stainless steel with different levels of interstitial impurity concentration was studied in an attempt to delineate the combined effects of the alloying elements. EXPERIMENTAL TECHNIQUES a) Materials and Fabrication. A commercial AISI 330 stainless steel and several specially prepared aus-tenitic alloys have been studied. The experimental alloys were prepared by arc melting the constituents under purified argon. Analyses of the materials are given in Table I. The commercial alloy was obtained as 5/8 in. bar stock and rolled to 0.092 in. sq, with several intermediate anneals. At this stage some of the material was annealed in Pd-purified hydrogen at 1100°C to establish different levels of interstitial content. All other heat treatments were in vacuum (10-5 torr). The "pure" alloy ingots were swaged to 0.120-in. rod and annealed in Pd-purified hydrogen at 1100°C. The analyses for these conditions are also contained in Table I. Following the above treatment, the final wire sizes Table I. Chemical Analyses of Test Materials Hrin Hydrogen at Cr, Ni, Alloy 1lOO°C wt pct wt pct C, ppm* N, ppm* Type 330 As-received 14.78 33.25 430 300 Type 330 64 14.78 33.25 40 50 Type 330 200 14.78 33.25 27 21 Fe/35 Ni 72 - 35.10 <10 62 Fe/35 Ni 200 35.10 <I0 44 Fe/35 Nil15 Cr 72 14.95 34.94 <I0 61 Fe/35 Ni/15Cr 200 14.95 34.94 <10 45 Fe/35 Ni/C $ 35.OM 380 *Sensitivity: N t 5 ppm Ct10ppm. f Nominal Ni content. % A master NiC alloy was used in preparation of this material; courtesy of D.E. Sonon. were obtained by either swaging or cold drawing. The test results did not vary with these techniques. b) Specimen Preparation. Two sizes of specimen and two gripping systems were used. i) 0.070-in. wire with a chemically milled gage section: 0.75 in. long, 0.060 in. in diam. These were fastened into grips containing tapped grooves. ii) 0.050 in. wire, gage length 1.5 in. Ball bearings were welded to the ends of the wires and the gage length was taken to include all material between the welds. Socket-type grips were used with these specimens. With specimens of type ii), joining was performed in a specially constructed brass jig, under argon, and automatic timing was utilized in the procedure. No adverse effects of welding were noted. Specimens were encapsulated and solution treated for 1 hr at temperatures selected to produce the same average grain size, -50 µ. Annealing twin boundaries as well as normal crystal boundaries were counted. The temperatures used are listed in Table 11. Table 11. Specimen Size. Temperature of Heat Treatment and Resulting Grain Diameters for Test Materials Recrystallization Resulting Material Condition Temperature Grain Sue AISI 330 Not H purified 0.070 120O°C 45 to 55µ in, wire AlSl 330 H , pure, 0.070 in. 1150°C 45to55µ wire Fc/35Nil15Cr Pure, 0.070 in. wire 1000°C 45tossp Fe/Ni Pure. 0.070 in. wire 775°C 45 to 55µ Fe/Ni/C Pure, 0.050 in. wire 850°C 10 to 20p AlSl 330 Not purified, 0.050 1150CC 45to55p in. wire AlSl 330 ti, pure, 0.050 in. 1150°C 45to55p wire

Jan 1, 1970

By T. J. Smolik, Harman, D. W. Fuerstenau

By means of electrokinetic measurements, the surface properties of the aluminosilicate polymorphs (sillimanite, andalusite, and kyanite) and also mullite have been found to depend on the ratio of A10 bonds to SiO bonds in the surface. The Al-toSi ratio in the surface is dependent upon the crystal lographic properties of the mineral, which in turn determine coordination numbers of A1 and of Si, cleavage characteristics, and density of the various solids. Mullite with a greater bulk Al-toSi ratio has the highest zpc of the aluminosilicates. By treatment in dilute acids or by cycling between acidic and basic solutions, alumina is selectively dissolved from the surface of these orthosilicates. This shifts the apparent zpc to lower pH values as the fraction of SiO groups in the surface increases. Thus, surface properties can be altered by procedures that alter the A l-to-Si ratio in the surface. Flotation of these aluminosilicates results from electrostatic interaction of the collector ions with the mineral surfaces. As a result, flotation response shifts in accord with any shift in apparent zpc by pretreatment. Separation of minerals by flotation is based on differences in the physicochemical properties of their surfaces.&apos;-3 For many minerals, adsorption of flotation collectors results from their functioning as counter ions in the electrical double layer at solid-water interface. In such systems, separation depends on differences in the zero point of charge (zpc) of the various minerals. The zpc is defined as the concentration of potential determining ions in solution at which the surface is uncharged. The potential determining ions for inorganic oxide-water interfaces are hydrogen and hydroxyl.4,5 This work is concerned with the effects of crystal structure, composition, and surface preparation on the surface properties and flotation behavior of aluminosilicates. Differences resulting from crystal structure were studied by measuring electrokinetic potentials and determining the flotation behavior of three different aluminosilicate materials having the same chemical composition (Al2O3 SiO2), namely andalusite, kyanite, and sillimanite. Furthermore, the effect of the Al2O3-to-SiO2 ratio on flotation behavior and surface properties was investigated by including synthetic mullite, 3A12O3 .2SiO2. Gaudin and co-workers 6,7 have clearly shown how crystal structure determines the native floatability of certain minerals. Those solids in which the surface is comprised mainly of broken residual bonds possess naturally hydrophobic surfaces. It was found by Bakakin8 that for a number of oxidized lead minerals, differences in floatability were due to the distance of Pb atom from the surface. Only limited work has been done on relating electrical properties of surfaces to crystal structure and composition. Healy et. a1.9 found that the zero points of charge of various manganese dioxides ranged from about pH 1.5 to pH 7.5, and these differences in the zpc&apos;s were interpreted in terms of the atomic packing in the various crystals. The research presented here clearly shows that crystal structure and chemical composition do affect the surface properties of aluminosilicates and, in addition, that these effects can be altered by changing conditions under which the surfaces are prepared. CRYSTAL STRUCTURE OF THE ALUMINOSILICATES Sillimanite, andalusite, and kyanite are composed of regionally metamorphosed rocks differing mainly in degree of metamorphism. All three minerals have the same chemical composition, Al2O3 - SiO2, of which sillimanite is the high temperature polymorph and kyanite and andalusite the lower temperature polymorphs. Andalusite and sillimanite crystallize in the orthorhombic system while kyanite crystallizes in the triclinic system. The structure of these three minerals is essentially chains of aluminum-oxygen octahedra linked laterally by silicon and aluminum. The arrangement of these chains in the three minerals is shown in Fig. 1.l4

Jan 1, 1967

By T. J. Koppenaal, M. E. Fine

A yield point effect attributed to short-range ordevi?g (SRO) occurs in Cu base Al. At at 296°K varies with heat treatment, decreasing as the annealing ternperature is raised .from 433Oto 598°K. Davies aid Cahn&apos; observed a corresponding decrease in SRO. (523 °K anneal, measured at 77°K) is approximateZy proportional to the variations of A7 with strain rate and testing temperature are also Consistent with the idea that is associated with SRO. A preliminary investigation of the tensile properties of a Cu-Al single crystals showed the presence of a rather strong yield-point effect (drop in flow stress after initial yielding). The object of this research was to investigate its origin and behavior. a Cu-Al alloys are particularly interesting because diffuse X-ray scattering measurements by Davies and Cahn,&apos; Houska and Averbach,&apos; and Borie established the presence of short-range order. The degree of local order may be changed with heat treatment.&apos; cottrel14 suggested that the presence of local order might result in a yield-point effect, and thus the possibility exists here for experimentally ascertaining the importance of short-range order with respect to yield points in these alloys. Since a 12 pct difference exists between the atomic sizes, elastic or Cottrell locking5 must also be considered. Further, Howie and swanne have shown that the stacking fault energy of copper is reduced by aluminum additions. The width of extended dislocations should thereby increase. hus the conditions appear attractive for Suzuki locking.&apos; Finally, the possibility of stress-induced order at dislocations, schoeck locking,&apos; must also be examined, EXPERIMENTAL PROCEDURE Alloys up to 14 at. pct Al were prepared by induction melting high-purity (99.999 pct) Cu and (99.996 pct) Al in a graphite boat under a dynamic vacuum of 5 X 10o mm of Hg. After homogenizing the ingots at 900°C for at least 24 hr under vacuum, they were rolled with intermediate anneals to strips 1.55 mm thick. Single crystals 10 in. long were grown by lowering strips, contained in a split graphite mold sealed in fused quartz at 5 X lo-&apos; mm of Hg, through a single coil induction heater at a constant rate of 1/2 in. per hr. Tensile specimens 1.25 in. long were cut from the single crystal strips and reduced cross sections about 0.7 in. long and 3.0 to 3.5 mm2 in area were introduced by filing and abrading.8 To remove the worked portion about 10 pct of the cross-sectional area was removed by etching. Back-reflection Laue photographs of a filed and etched specimen were taken before and after annealing at 900°c for 24 hr. Small, well defined Laue spots were obtained with no visual difference in the two photographs. Further, specimens with and without the reduced sections began yielding at about the same stress. Hence, for our purposes, filing and abrading did not affect the structure of the specimens. Each single crystal specimen was annealed at 900° c in vacuum for at least 24 hr and furnace cooled; while cooling through the range of 250o to 200°c, the rate was about 55°C per hr. Orientations were determined by the usual back-reflection Laue

Jan 1, 1962

By AIME AIME

THE fall meeting at El Paso this year (Oct. 13¬15) will be of unusual interest due to the international atmosphere imparted by the many engineers from Mexico, who are making arrangements to attend this meeting. The meeting will be held jointly with the Western Division of the American Mining Congress. Cooperating in the program will be the representative society of Mexican engineers known as Centro National de Ingenieros of Mexico City, who are plan¬ning on sending many delegates and well known Mexican engineers to the convention. The cooperation of the West Texas Geological Society and the American Association of Petroleum Geologists has also been secured. Brent N. Rickard, manager of the El Paso Smelting Works of the American Smelting & Refining Co. at El Paso, Tex., is general chairman in charge of arrangements. He is receiving splendid cooperation from the Mining Department of the El Paso Chamber of Commerce and from the business people of El Paso, who feel highly honored in having these mining societies meet with them this year.

Jan 1, 1930

By Ta M. Li

How do you convert a copper-zinc resource into a viable economic mining operation? This problem, unlike most, was complicated by the additional presence of a sub-arctic climate, highest labor costs in the world, low-grade copper-zinc values, depressed market prices, and a complex mineralization.

Jan 12, 1977

By Clyde E. Williams

THROUGHOUT its history the American iron and steel industry has constantly striven to improve the quality and reduce the cost of its products. No one needs to be told how well it has succeeded. Its success in making steel products at such a low cost has been achieved mainly through large-scale production. While costs have gone down as the rate of production and the degree of mechanization increased, quality of product has been actually improved. Thus high-tonnage records are important only in the light of high quality of the steel. Quality is the watchword! Continual improvement in quality has come as a result of research, not only in the laboratory but in the large commercial units in the plant. In fact, so many operations of the industry are on such a huge scale that experimental work must be done under commercial operating conditions so every progressive steel plant is a research laboratory.

Jan 1, 1938

By W. R. Crane

THE effect of mining in the red-ore mines of the Birmingham district has been observed for some time, but, except in a few localities, little difficulty has been experienced from disturbance of cover. Cave-ins near the outcrop and fracturing of the surface at greater distances are the most pronounced manifestations of disturbance, while limited areas at points distant from the outcrop and under greater depth of cover have actually subsided. There is no doubt but that in time, because of failure of pillars, extensive fracturing and widespread settlement of the surface will result, particularly along the slope of Red Mountain, where mining has been under way for many years. Were it not that the orebed is overlain by one or more water-bearing formations, the fracturing or settlement of the surface would not be serious; but because of these formations, fracturing of the top rock may in itself be of sufficient importance to warrant the adoption of protective measures. Until development openings and surface plants are transferred to Shades Valley, protection of the surface will probably not be considered imperative, as the area involved is not of particular value for agricultural or building purposes. Further, the collapse of pillars over a wide area may develop squeezes that, if not controlled, may jeopardize the integrity of the mines and necessitate a change in development, from slopes to vertical shafts, at a much earlier period than is now contemplated. The occurrence of heavy beds of strong tough materials at varying distances above the orebed make it doubtful whether any serious disturbance of the surface will be experienced at any considerable distance from the outcrop, although some settlement will probably take place. It is certain, however, that no great volume of water will enter the mines from fracturing of the Fort Payne chert bed, as this is known to be a compact and practically impervious formation beyond the leached zone. Not so much can be said, however, regarding other possible sources of water, as pervious beds and through faults that may be encountered in future mining operations.

Jan 8, 1925

By Joan Melcher

The oil embargo and increasing disillusionment with nu- clear power have put this country&apos;s abundant coal reserves in growing demand. Both the government and industry are looking toward increased coal mining, and with this goes an increased interest in new and advanced methods of coal utilization. One advanced coal system stands out among the rest-magnetohydrodynamics (MHD). Its high efficiency, strong probability of sulfur dioxide control, and limited consumption of cooling water place MHD in a unique position to help the power generation industry. Another point in MHD&apos;s favor is the capital costs of operation, which are lower than those of other advanced technologies. However, initial costs are higher and realization of a commercial MHD plant in this country may be more than a decade away.

Jan 12, 1977

By Charles S. Barrett

THERE is a road into the microscopic realm that has remained untraveled through all these years of intense activity with high-power optical and electron microscopy. The road is worthy of careful scouting by metallurgists and other investigators, for it leads into relatively new country and it makes some areas accessible that heretofore could be reached only by very indirect paths or by the use of imagination. And when the road passes through familiar territory it frequently permits a new view of commonplace things that should prove of value from time to time. An accepted way to interest people in new sights such as this is to present an illustrated travelogue. This I propose to do, using many pictures taken in my recent exploration of this road. In the manner of travelogues, I shall touch briefly upon a large number of different subjects in physical metallurgy and shall, attempt to give an exhaustive treatment of none, for the objective is to provide a means for further research, to interest others in it, and to indicate what appears at the moment to be profitable directions for it to take. The method I shall present involves X-rays, but does not make use of the usual accompaniments of X-ray research such as reciprocal lattices, Fourier series, or the stereographic projection. The method is so simple in its fundamentals that it could have been developed 20 years ago, or perhaps even 30 years ago. It is well to have a destination for our travels, so that when we are through we shall have explored some region of importance, despite our preoccupation with the novel means of transportation and our interest in the sights to be seen along the way. So let us name the Cold Worked State as our destination, and make side trips into the territories known as Recovery, Recrystallization, and Precipitation-hardening. A great many investigations have been made of the nature of cold-worked metal, and a great variety of methods used, many of which are indirect, such as X-ray line intensities, X-ray line widths, calorimetric measurements, and magnetic measurements. Since comprehensive reviews of these investigations have been published in recent years, they need not be discussed here. The investigations that were the direct forerunners of the present work should be first mentioned. In 1931 I became interested in the structure of individual spots in X-ray diffraction patterns.1 When a crystal is placed in the narrow pencil of X-rays in a Laue camera, the spots recorded on the film are not always uniformly black, but may have an internal structure. The meaning of this may be understood from Fig. 1, which represents a narrow beam containing X-rays of many wave lengths ("general radiation") penetrating a crystal in the direction of the arrow and forming a pattern on the vertical film at the right.

Jan 1, 1945

By Roland Kammel

For electrolytic recovery of silver from dilute aqueous solutions improved mass transfer is necessary to achieve favourable current efficiencies and high space-time yields. The many cell designs proposed for this application can be divided into two different groups: cells from which the silver must be redissolved and cells from which the deposit can be reclaimed as a metal. Introduction Electrolytic silver recovery methods have proven advantageous under technical and economic aspects for the treatment of rinse water, still rinses and spent silver solutions in the electroplating and surface finishing industry, of exhausted fixing baths from photographic processing, bleed electrolytes from silver refining processes and leach liquors. Examples of the compositions of typical dilute silver solutions are listed in Table I.

Jan 1, 1984

By Alicia O&apos, Overbeck, Reardon

DIFFIDENTLY, because don&apos;ts are rarely greeted with cheers; humbly, because I, myself, have never lined up with the irreproachables, I venture on the subject of manners for the mining camp matron. Mining camps can be divided roughly into two types-the large, opulent settlement that blooms like the rose about a strong mine in full operation; and the puny group of adobe huts, or calamina shacks, or even canvas tents flung down in the wilderness to shelter the gay pioneers of a shining prospect or the shattered survivors of a lost hope. Of the first, I know nothing; but in the second, I have spent some of my best years, and from its curious code of morals and manners, its comic hates and its unreasoning loves, its high impatience and its engulfing kindness, I have charted the narrow .and pitted path which must be trod by the woman who would success¬fully live therein.

Jan 1, 1936

By Arthur Mackwell

The role of the precious metals is changing rapidly. They are becoming primarily materials of modern industry, and their decorative and monetary functions are diminishing in relative importance. Certainly gold is still the premier metal for jewelry, as silver is for silverware. But these uses are not growing nearly so fast as are the uses of these metals in a variety of industries. This is even more true of the platinum metals. Moreover, this is true despite the fact that the precious metals are highly expensive and liable to substitution by the base metals in cases where this is feasible. For the fact is that the physical and chemical properties of the precious metals make them relatively invulnerable to substitution; where they can be replaced by the base metals, they have been, and the opportunity for further substitution is, therefore, limited. SILVER In November 1969 the United States Treasury stopped minting the only remaining coin with any silver content. That was the silver-clad Kennedy half dollar, which had a silver content of approximately 40%. The step was taken out of necessity, because of the rising shortfall between world mine production and consumption. It was important to divert the 35 to 40 million oz of silver per year used for the minting of this coin into the open market, where it would be available for industrial consumption. This decision was important, not only for its practical effect but also for what it symbolized. Only four years earlier, in 1965, the Treasury had used 320 million oz of silver" for the full range of coinage. Now not an ounce of silver goes into the United States coinage. The reason is simple and yet complicated. For many years the U.S. Treasury had purchased silver at prices which provided a subsidy to domestic producers. As a result, silver producers were eager to sell to the Treasury, and that agency built up a huge supply of the metal -almost 2 billion oz by- 1961. But, as the free-market price neared $1.29, the basic melt value of the coinage, the Treasury became a seller of silver, not a buyer, and its stock was depleted rapidly. The Treasury lost more :than a billion ounces of silver in the years 1962 through 1965, and it continued to lose silver, both through coinage and through sales to consumers, through 1969. The Government continued to sell silver to consumers at the rate of 1.5 million oz a week, even after terminating the 40% silver Kennedy half dollar. But it was apparent that the Government stocks could last no more

Jan 1, 1976

By E. S. Moore

ALTHOUGH nickel was in use in alloys long before the Christian era, the metal was not discovered until 1751, when Cronstedt recognized it in niccolite from Sweden. The Chinese apparently used a nickel alloy, known as "pahfong" thousands of years ago and Persian coins dating farther back than 200 B.C. consist of a copper-nickel alloy similar to some of those now in use in coins. The pure metal was first prepared about 1775 and the metal was refined for commercial purposes some years later. The nickel industry did not attain much prominence until the ores in New Caledonia were discovered. Exports of ore from that country began in 1875 and since that date there has been an ever-increasing world output of nickel and a great expansion in the uses of the metal except during short periods of commercial and industrial depression. Previous to 1875, for a number of years, Norway was the chief producer, although the metal was mined also in Sweden, Finland, Italy, Germany, Austria, France, China, the United States and other countries. With the dis-covery of nickel deposits in the Sudbury district, Ontario, a new factor was introduced into the nickel industry and Sudbury has since become the overwhelmingly dominant feature in the world&apos;s nickel markets. Although nickel was first discovered in Canada as early as 1848 near the north shore of Lake Huron and nickel-copper sulfides were found in 1856 by surveyors working close to the present location of the important mine at Creighton, in the Sudbury field, it was not until 188.3 that any importance was attached to this field. In that year copper sulfide attracted attention where the main line of the Canadian Pacific railroad was being projected across Canada to the Pacific coast. Mining began near this discovery in 1889 but in the meantime operations had begun in 1886 in other parts of the field and by 1890 about 100,000 tons of ore had been raised. In the Sudbury field, as in Norway and at the old Lancaster Gap mine in Pennsylvania, the ore was first mined for its copper content and difficulty in the refining of the copper led to the discovery of the important proportions of nickel in the ore. No. 3 property of the Inter-national Nickel Co., now known as the Frood, the greatest deposit in the

Jan 1, 1932

By AIME AIME

PERHAPS the outstanding characteristic of the newly elected President of the Institute is his rare ability to set aside nonessentials, and pick out the few basic elements on which a valid conclusion on any question can be drawn. This holds whether he is appraising a mining enterprise, selecting a man for an important position, deciding whether to buy or sell a bond, or choosing the best method for mining a huge body of ore. For example, he has pointed out that the two primary factors that make for success in a copper-mining venture are a large reserve of reasonably good ore and competent management. Usually the first is not as difficult to gauge accurately as the second. In a big enterprise the quality of the management

Jan 1, 1939

By Clyde E. Williams

IN planning a postwar program for manufactured products, it is essential that the bases for the plans be wisely chosen. First we must make certain assumptions as to the war&apos;s ending. Let us assume: (1) complete victory by the United Nations, (2) peace terms that will ensure the direction of the economy of all nations of the world toward peaceful pursuits, and (3) an early ending of the war, that is, before the nations of the world, excluding the enemy, are near the point of physical and spiritual exhaustion. Thus, our manufacturing plants and transportation facilities will still be in good shape. The plants and transportation facilities, as well as the cities of a large part of Europe, however, will be badly crippled. The rich mineral and other raw material resources of the world, little of which was under control. of the Axis powers before the war or will be after the war, will not be used up. Control of these raw materials, or at least an important part of them, will remain in the hands of the strong peaceful nations.

Jan 1, 1943

By D. Hanson

Fox most of their practical applications metals are required to with-stand stresses of appreciable magnitude: indeed, it is because they possess the quality of resisting stress without becoming permanently deformed that they find such extensive use in the service of man. Metals and alloys must, in service, usually behave as elastic substances-or nearly so. It is not difficult to satisfy this condition at ordinary temperatures. Iron and its alloys, especially the steels, are at normal temperatures excellent elastic bodies, capable of satisfying most of the mechanical requirements of the engineer: where electrical, chemical or other properties are impor-tant, which cannot be met by steels, it is usually possible to find a non-ferrous alloy such as nickel, copper or aluminum, which will prove satisfactory. When the metals or alloys are not inherently sufficiently elastic, cold-working or heat-treatment may develop elastic properties to a sufficient extent for practical needs. By means of relatively simple, rapid tests we can measure such properties as elastic modulus, limit of proportionality and proof stress, upon which design can be based with confidence. The case of the soft metals, such as lead and tin, is well known to be exceptional. They possess no definite limit of elasticity, and the value of proof stress or tensile strength depends to a great extent on the speed with which the test is carried out. Design here must be based on other considerations than a well-established theory of the proportionality of stress and strain. It is now generally recognized that steels and non-ferrous alloys possess at temperatures not greatly exceeding that of the atmosphere, characteristics quite different from those existing at ordinary temperatures, and that they assume qualities similar to those of the soft metals. Not only have they no limit of elasticity, but the proof stress and the ultimate stress depend on the time of application of the load. Flow under load may persist for long periods of time, possibly indefinitely, and the determination of a true maximum stress becomes a matter of great difficulty.

Jan 1, 1939

By L. Weaver

THE Tennessee Copper Co.&apos;s mines are in the southeast corner of the state of Tennessee, Polk Co., in the well-known Ducktown copper basin. Their new circular production shaft will eventually be the only ore hoisting shaft, and is located for handling ore from Boyd, Calloway, Mary, and Cherokee mines. A circular, rather than a rectangular, shaft was decided upon because: 1-The circular shaft section is stronger when lined with concrete. Reinforcing steel was not required, thus reducing lining cost by one- quarter. 2-Water sealing was desired; it was thought it could best be done with a concrete lining followed by pressure grouting to eliminate water seeps. 3-The shaft labor saving equipment could best be used in a large opening, so the round section was made for economy, sinking, mucking, concreting and water sealing. Less shaft steel is used than could have been possible with steel sets. There are no posts required; center beams and Tee plate assembly placed at 10 ft hold the 100 lb steel guide rails.

Jan 1, 1950