Search Documents

By Antonio Adel dos Santos, Carmos Antonio Gandra, Fabricio Mazola da Silva Paiva, Vicente Tadeu Lopes Buono

Abstract Usiminas Steel Plant in Ipatinga installed an accelerated cooling device named CLC (Continuous On-Line Control) in 2010, enabling it to supply steels produced by TMCP (Thermo Mechanical Control Process) technology. This technology complements the TMCR (Thermo Mechanical Control Rolling), with the inclusion of the accelerated cooling process after controlled rolling. There are various gains in terms of quality and productivity associated to the application of such technology. However, the flatness control for API steel becomes crucial because large thermal stresses may be generated due to thermal heterogeneity during the fast cooling when the austenite phase decomposes mostly into ferrite and bainite. In literature, there is lack of knowledge regarding a full understanding of the relation among cooling conditions and plate flatness. Therefore, this work has focused on the effect of the cooling strategy for API steels, aiming at optimizing flatness and keeping the mechanical properties within the specified ranges. The starting point was dilatometer simulation, where cooling conditions such as start cooling temperature, SCT, finish rolling temperature, FRT, and cooling rate, CR, were changed in order to evaluate their effect on microstructure. Those laboratory conditions supposed to give the best results were transposed to industrial scale, so as to produce experimental lots of plates with five different cooling strategies. It was shown the possibility to find a cooling profile that guarantees the balance between mechanical properties and flatness requirements. The influence of cooling strategy on flatness was explained by the varied heat transfer regimes occurring from hot steel surface to the ambient

Oct 1, 2019

By Anna Carolina Cerqueira Neves

Synthetic fibers have been gradually replaced by lignocellulosic fibers. Compared to the synthetic fiber, natural fiber showed economic and environmental advantages presenting interfacial characteristics with polymer matrices that favor the impact energy absorption by the composite structure. However, so far little has been reported about the hemp fiber embedded in polymer matrices, such as tensile properties. This study aims to evaluate the resistance in tensile tests of epoxies composites reinforced with different percentages of hemp fiber. Tensile tests were submitted with percentage of 0%, 10%, 20% and 30% incorporated hemp fiber in epoxy matrix. The tensile strength and deformation substantially increased the relative amount of hemp fibers incorporated into the polymeric matrix.

Aug 16, 2017

By Guilherme Corrêa Soares

Deeper understanding about the strain hardening behavior of steels has become necessary due to its importance in industrial processes such as mechanical cold forming, rolling and drawing. In this work, the strain hardening behavior of AISI 304, non-grain oriented electrical (NGO) and dual phase steels was investigated. Tensile tests were performed and the strain hardening behavior of each steel was studied by the Hollomon’s equation. X-ray diffraction measurements and hardness tests were also carried out in order to characterize the specimens. Different work hardening stages were observed in each steel during the deformation process. The results obtained are discussed in terms of the relationship among the instantaneous strain hardening coefficient, hardness and eventual phase transformations. The instantaneous strain hardening coefficient of dual phase and NGO increases after the yield point, rapidly reaching its maximum and then steadily decreases until tensile strength is reached. In AISI 304’s case, the strain hardening coefficient keeps raising to high values in response to a large strain and then rapidly decreases before reaching the tensile strength. In comparison to the other steels, AISI 304 shows higher instantaneous strain hardening coefficient value, which persists even in large strains. This is a consequence of its strain hardening mechanism based on stress-induced martensite transformation.

Aug 16, 2017

By John Hinton

Electromagnetic based (EM) sensor technology has been shown to detect changes in the magnetic permeability of steel strip travelling down the run out table after rolling. Measuring below the Curie temperature, these changes can be interpreted in terms of the phase transformation from austenite (paramagnetic) to ferrite (ferromagnetic). These real time measurements provide a detailed insight into the changes in the structure at high temperature providing the steel producer with feedback on quality control, product consistency and product development. However unlike mill microstructure models, the sensor measurement provides a point reading at a distance through the cooling course. To map the transformation in more detail, a sensor array is required along the length of the Run Out Table i.e. to measure points on the austenite to ferrite transformation curve. This paper describes the process and metallurgical factors that should be considered in the optimum design of a sensor array, i.e. the number and location of the sensor heads. Examples of cooling strategies for different steel grades e.g. low carbon, structural and dual phase steels are used to demonstrate the importance of sensor location. In addition, the effect of variability within typical industrial parameters e.g. cooling speed, on the sensitivity of sensor output and location will be considered.

Oct 1, 2019

By José Aparecido Pereira

The customer asked for a 5” angle roll pass design. For this angle, in a normal pass design, a 160mm billet is required. For the production of this billet would be necessary a new 160mm mold for the Continuous Casting Machine, which produces 150mm billets, increasing the complexity of the melt shop. The rolling mill is designed to produce angles up to 4", technical information recommended the replacement of a gearbox because this process would generate torque up to 15% above nominal. An innovative roll pass design was done using 150mm billet using the Aparecido-W Method that cause a higher spread in the first three passes, thus reaching the desired leg length. As this method is not used in any other known rolling mill, a FES (Finite Element Simulation) and FEM (Finite Element Modeling) was done by a Research & Development center which demonstrated that the design was viable. From July, 2018, three tests were done being produced around 700 t of good quality products without difficulty of set up. The rolling mill team carried out this project at a very low cost and in record time of five months. The average torque of the motors was 36%, without overload for the equipment.

Oct 1, 2019

By Cristina Escudero Martinez

The purpose of the Basic Oxygen Steelmaking (BOS) is to refine the hot metal produced in the blast furnace into raw liquid steel, which may be subsequently refined in the secondary steelmaking shop. Appropriated fluxes for the BOF could require low melting point to reduce the energy consumption, to reduce the energy to fluidity the slag at lower temperature and to melt at lower temperature than steel. It is necessary a good Tumble test result and the fluxes do not generate fines which could obstruct the blowing plugs, so we would have a homogeneous flux. A homogeneous chemistry that allows to control the basicity (Si and MgO levels) and a high absorption characteristics to combine the flux with P, S, Si, etc. are necessary. PASEK Dunite is an ultramaphic rock exploited in the north of Spain with a basic chemical classification being olivine and serpentine its principal minerals. It is formed by orthopyroxene, clinopyroxene and olivine in variable proportion. Dunite is a very homogeneous and hard stone. The main characteristics are: High hot and cold resistance to mechanical stress (shatter / crushing / abrasion), softening and melting points of a flux, not a refractory material, large porosity which is increased more than 20% when dunite is heated at BOF process temperature, and high absorption level, and stable components with low melting points. PASEK Dunite is a good flux in BOF process and its use is recommended if the BOF process produces pig iron with low Si content, generates high levels of slag and it is necessary maintaining the basicity index and the MgO amount and with high value of hot metal ratio (high amount of phosphorus to remove).

Aug 16, 2017

By Daniel Antonio Kapper Fabricio

A avaliação das propriedades de mecânica da fratura dos materiais é uma necessidade crescente, sobretudo no setor de óleo e gás. Esse cenário exige a garantia da qualidade na execução de ensaios de tenacidade à fratura. Esse trabalho tem como objetivo realizar uma comparação intralaboratorial para o ensaio de tenacidade à fratura KIC variando o executante do ensaio, visando atender ao requisito de garantia da qualidade da norma NBR ISO/IEC 17025. Os resultados foram comparados através de análise de variância. As diferenças entre os operadores não foram significativas frente ao erro residual a um nível de confiança de 95%, sendo tal resultado considerado satisfatório.

Aug 16, 2017

By Rainer Fackert

3D-Measurements for slabs and heavy plate are now available and close the gap in the production chain. The measuring systems described in this presentation must be seen as high-tech solutions in the field of casting and rolling technology. The measuring systems were developed taking into consideration the harsh casting and rolling mill environment in which they are to be used, with the aim of achieving high operational reliability and eliminating disturbances. Interconnected quality management systems enable optimization across the complete production process. New limits are being defined constantly for all these developments. What is technically feasible today becomes normal practice tomorrow, and will probably be replaced by completely new technologies the day after.

Aug 16, 2017

By Günther Staudinger

Aperam is a global player in producing of stainless, electrical and special steel qualities. The steelmaking plant in Timoteo Brasil is equipped with one AODconverter for stainless steel and one MRPL-converter for special steel production. The MRP-L converter is almost in operation for 20 years. In order to improve production Aperam decided to install a new converter with increased reaction volume equipped with DANIELI state of art technology. This paper describes the major changes and improvements of the new converter installation.

Aug 16, 2017

By Armando Vazquez

This paper will provide an overall technology update on Tenova’s modular i BOF® technology package for improved endpoint detection (Carbon and Temperature), slop detection and auto-tapping control, with a primary focus will be on Tenova's Slop Detection System (SDS). Accurate Slopping prediction is a critical tool in the operation of a BOF. It provides the steelmaker with an additional protective system to increase yield & productivity while reducing operating costs. Tenova Goodfellow's i BOF® slop-detection technology uses lance vibration analysis with real-time alerts to give steel makers advance warning of the onset of a slop and a measurement of the slop severity. The system is designed to provide direct feedback control of lance position and oxygen flow rate, for rapid mitigation of potential slopping events. This paper will provide a summary on how the i BOF® technology package has been implemented, including trials and general results.

Jul 30, 2018

By Michael Breuer, Christian Mengel, Luis Acainas Caballero, Olaf Jepsen

Stability of the hot strip mill rolling process remains a main topic when it comes to processing thin and hard materials. Strip steering especially at the end of rolling and tail out rips are a main source of unscheduled down times in a hot strip mill. Main focus of this paper is the new X-Roll® Guide system to improve mill stability and quality. An overview of SMS group developments in the recent years regarding equipment and control strategies is given. The new side guiding system in the entry area of the finishing mill is introduced and explained with operational examples. The system provides reproducible conditions for the threading process and during rolling. Steering control has a direct benefit on the availability of the mill. New developments of the roll alignment control strategies based on roll force and mill stand entry guide force measurement will be presented. Additionally a camera based measuring system is introduced that generates a direct process feedback of the strip position. It provides together with the roll alignment control the necessary control parameters for adjusting the roll gap and guiding the strip correct centered through the mill. As a summary the SMS group system is explained combining all features.

Oct 1, 2019

By Michael Brandner

In the past the research and development of new materials for hot mill rolls was mostly done by trials. Such trials are expensive and difficult to transform from small size to the big size of a solid roll. Computation is the cheaper way to get ideas processed and can be varied in different directions. The main part before simulation is the generation of the needed basic data of the specific materials. Some data is already well known and can be bought from databases; others have to be done specifically for our materials. The evaluation of such results has to be done still with solid trials, but the number of trials can be reduced. The advanced techniques of finite element calculation offer a wide range of possibilities to get answers about alloys, solidification, casting parameters and their influence. The possibility to calculate a heat treatment cycle and to get an answer about the internal stress modification during the cycle is a great help to understand the principle of transformation. Examples of different calculations in various fields will be given. The close cooperation with universities and other research institutes as well as the in-house possibilities will be presented.

Jul 30, 2018

By Mark Gilliam

Control of true steel level in the tundish during casting is desired in order to maintain the correct pressure head and thus provide a stable flow to the mold. Also the control of tundish draining prevents slag carryover and can increase yield at each end of cast sequence. At Steel of West Virginia (part of the SDI Group), it was understood that to be able to measure the true steel running level and control the drain level at the end of casting would be a great benefit during production at their three strand billet caster. This paper sets out to show how an evaluation process was started to find the best method to determine steel level in the tundish and to prevent the steel level dropping low enough to allow slag to enter the mold. Also how the decision was taken and a real time molten steel measurement system was installed and by utilizing the resulting data in the process, how slag in the mold was removed as an issue, how lost production was reduced and how consistent steel level has provided constant casting speeds and improved stream integrity, all leading to realized quality improvements. Other areas discussed within the paper will be the training of operational staff, the difficulties to be overcome when first installing new equipment and how these teething problems were cured by close co-operation between the steel plant and the equipment suppliers. In conclusion the paper will discuss the production improvements achieved, production cost savings at the plant and how the generated data was integrated into the plants process control system.

Aug 16, 2017

By Rene Grabowski

Optimization of workflows and intelligent stock management; Slab stacking improvement by automated transport orders; and System automatically registers any slab movements even in manual operation. Case story: Steel producer ArcelorMittal Eisenhüttenstadt GmbH in Germany uses Primetals Technologie’s new stock yard logistics system in its finishing department. An exact image of its slab storage at any times is given by the warehouse logistics system to the company. It not only enhances the composition of the stacks of slabs, but also automates recording of manual restacking operations. Therefore the solution improves workflows and simplifies stock control. Cycle times have also been reduced due to the fact that the slabs can be charged to reheating furnaces ahead of the rolling mill due to less restacking operations within the slab storage. The expandable, modular system is based on the Siemens Simatic IT and Primetals Technologies’ IT4METALS Logistics product platform. It provides a large number of organizational and commercial features in the form of sophisticated graphics and tabular evaluations. For example, it can show how many crane movements have been made per shift for any category of slab, so that the time and cost for each operation can be calculated accurately.

Aug 16, 2017

By Douglas Glenn Stalheim

The uniformity of the final cross sectional microstructure and subsequent final mechanical properties and shape of structural steels is dependent on the type or types of recrystallization behaviors that are created. There are three main recrystallization behaviors that are the foundation of the metallurgy created during production. Alloy design and subsequent processing design strategy drive how much of each recrystallization behavior is created through the cross section of the product. Carbon manganese steels create only one basic behavior while the addition of microalloys, in particular niobium, can add two additional behaviors. The behaviors are intertwined with each other and build upon each other. The three behaviors are Type I, static recrystallization, Type II, no-recrystallization, and Type III, metadynamic/dynamic recrystallization. How much of each behavior is generated through the cross section through the production influences the final transformed microstructure and corresponding mechanical properties and shape performance. This paper will discuss the three behaviors, how they are generated, how to identify which behavior is occurring through modeling or actual mill data. Actual examples from production will be discussed.

Aug 16, 2017

By Pedro Antunes Amaral

Currently there is a constant and essential concern of preserving nature. Over the years the concern with the environment is increasing, new environmental laws are emerging and being applied more rigorously and consequently emerge economic needs and mineral processing practices and other materials. In this sense briquetting becomes an alternative to fine particles agglomeration by means of pressure and or temperature, with the aid or not of a binder, which allows to get a product not only compressed, which presents shape, size, and adequate mechanical properties. The reduction in volume of the material in some cases (beyond the technological benefits) also allows fine materials can be transported and stored more economically, safely and effectively. The production of coke is greater as the content of better coking coal is, thus he low capacity coking coal is not much used in coke ovens. This research aims to demonstrate that briquetting of mineral coals with low coking coal capacity is possible, additionally allows increased coke production, obtaining then a better yield of coke. Basically they take advantage of low price of no coking coals without changing the quality of the coke produced. Anyway, briquetting became a smart alternative to aggregate values, economy and care for the environment.

Oct 30, 2017

By Sébastien Gérardin

Developed for more than 30 years, continuously improved, cored wire is nowadays a reliable solution for the improvement of sustainability, safety, health and doing quality and cost saving. Cored wire allows the addition of ferroalloys and treatment of liquid steel, especially concerning the calcium treatment. Amongst all the processes in secondary metallurgy, calcium treatment is certainly the most critical one before casting. Besides the traditional CaSi and CaFe wires, new types of wire have been designed for becoming the new reference in calcium treatment. PapCal (calcium insulated wire) and HDx (high density calcium wire) are a very versatile range of products. Indeed, according to the steelmaking process parameters (steel grade, treatment temperature, ladle size, calcium content targeted in tundish and even injection conditions), their technical specifications may be adapted in order to optimize the calcium treatment as high as possible.

Aug 16, 2017

By Jônatas Venancio Barbosa, Dagoberto Brandão Santos, Túlio Magno Füzessy de Melo

In this work, the mechanical and metallurgical behavior of titanium added ultra-low carbon (ULC-Ti) steel under hot and warm working conditions was studied by means of dilatometer compression tests. Double compression schedules were performed at temperatures between 700°C and 1000°C, inter-pass times of 0.5-100 s, and deformations of 0.5 and 0.3 in the first and second stages, respectively, with strain rate of 1 s-1. The analysis of the flow curves obtained allowed the evaluation of the softening characteristics of the steel. The softening and microstructure features indicate different restoration mechanisms depending on the temperature range. Static recrystallization with rapid microstructure restoration is observed at temperatures within the austenitic and intercritical field. Strain induced boundary motion and recovery mechanisms apparently control the restoration process in the ferrite region. In general, flow stress curves showed dynamic recovery behavior. Only the deformation in the intercritical region produced a peak in the flow stress curves. Isothermal holding tests associated with single hit compression indicated the presence of dynamic strain induced transformation, accelerating the softening kinetics at the intercritical region.

Oct 1, 2019

By Samuel F. Rodrigues, Clodualdo Aranas Jr., Fulvio Siciliano

The application of thermo-mechanical control processing (TMCP) in hot rolling of steels has become a common routine since the last 60 years. The understanding of the physical metallurgy behind TMCP played a major role in the early developments. Physical and numerical simulation works are performed firstly to derive the fundamental metallurgical knowledge and secondly to conceive existing TMCP practices. In this paper, a summary TMCP techniques is presented. The occurrence of dynamic transformation of ferrite in the austenite region is shown by means of synchrotron light diffraction methods. This phase transformation mechanism is taken into consideration and its effects on TMCP are proposed in an exploratory way.

Oct 1, 2019

By Luca Tommasi

Danieli complemented its wide range of production plants for the iron and steel industry with a further step upstream into iron ore pelletizing and beneficiation. Danieli has engineered and constructed a state of the art and fully automated pilot plant facility – pot grate and sinter box – at Altos Hornos de Mexico S.A. (AHMSA) Pelletizing Plant, Monclova, Mexico. Installation and commissioning were completed in October 2009. Key features of the pot grate include the avoidance of the need for operator intervention during the test, automatic system preheat, absence of dead time, heat recuperation system with an air/air heat exchanger, oxygen control in preheating and firing with zirconia oxygen analyzer, possibility to test deep beds up to 625 mm. A series of projects have been accomplished by AHMSA availing of the pot grate facility with the aim to enhance pellet plant productivity and to reduce operating costs. The results obtained by use of Danieli pot grate combined with the experience and skill of plant operators has shown significant technical and economical benefits thus fully justifying the initial investment made by AHMSA and confirming the importance of having an in-house testing facility in order to optimize industrial plant operations.

Aug 16, 2017