Search Documents

By H. H. Einstein

This paper reviews how uncertainty has been dealt with over the past 40 years using the decision making cycle as a frame of reference. The review of the phases of this cycle, as applied to rockmechanics and rock engineering, namely characterization, performance analysis, updating and decision making shows that in each, progress has been made over the past 40 years, although most of the basic concepts existed already in the 1960’s. Characterization is the area in which the greatest scientific steps were taken, this phase and performance analysis also gained from the tremendously expanded computational capabilities which allow one to use both more complex and more practically oriented models. The greatest practical advance is without using any doubt in risk based decision making although its acceptance shows interesting differences between different professions. Dans l’article suivant on utilise le cycle de décision pour illustrer le développement du traitement des incertitudes en mécanique des roches et en construction en roche dans les quarante années passées. La revue des phases du cycle de décision montre qu’on a fait du progrès dans chaque phase du cycle de décision, c’est à dire dans la caractérisation, dans l’analyse et la prédiction du comportement, dans l’actualisation et dans l’acte de décision, même si les concepts fondamentaux existaient déjà dans les années 1960. Les plus grands avancements scientifiques se trouvent dans le domaine de la caractérisation tandis que l’analyse prédictive profitait du développement de l’informatique qui a mené à des modèles plus complexes mais aussi plus pratiques. Le plus grand progrès est sans doute dans le domaine de l’acte de décision sur la base des risques. Ce procédé est devenu assez commun même s’il y a encore des différences d’acceptation entre différentes professions. Im vorliegenden Artikel wird der Entscheidungszyklus gebraucht, um darzustellen wie sich derUmgang mit Unsicherheiten im Felsbau während der letzen 40 Jahre entwickelt hat. DerÜberblick über die Phasen des Entscheidungsprozesses zeigt, dass bei der Anwendung in derFelsmechanik und im Felsbau, in allen Phasen d.h. bei der Charakterisierung, bei der analytischenVorhersage, beim Aktualisieren und bei der Entscheidungsfindung Fortschritte gemacht wurden,obwohl die grundlegenden Konzepte bereits in den 1960er Jahren existierten. Im Gebiet derCharakterisierung gab es wohl die grössten wissenschaftlichen Entwicklungen, während dieanalytische Vorhersage vor allem von den Fortschritten der Informatik profitierte, welchekomplexere wie auch praktischere Modelle möglich machte. Der grösste Fortschritt ist ganz sicherin der Entscheidungsfindung zu beobachten, wo Risikobetrachtungen gang und gäbe sind, obwohlhier noch einige Unterschiede zwischen verschiedenen Berufsgattungen zu finden sind.

Jan 1, 2003

The reactions between molten aluminium and cryoIite have been determined from a material balance of all components involved in the process. The interpretation of results were supported by x-ray diffraction studies of the evolved vapours, quenched electrolyte samples, and side-reaction products.The most important reaction involves the formation of both Na2F (sodium subfluoride) and chiolite in the fused electrolyte. The Na2F accelerates vaporization of the melt. Some AIF (aluminium monofluoride) may also be formed but the proportion of this is much less than for the former subvalent compound.

Jan 1, 1968

By W. A. Tiller, J. D. Harrison

HOT pressing of powder particles has gained importance recently, since it affords a method in which high densities are rapidly attained. In a recent study on hot pressing of alumina powders, Mangsen, Lam-bertson, and Best1 have shown within the limits of their experiment, the validity the rate equation for densification in hot pressing, originally proposed by Murray, Livey, and Williams.2 i.e., where D = fraction of theoretical density, t = time, P = pressure and 77 is the viscosity, all in appropriate units. This equation was derived from earlier work of Shuttleworth and Mackenzie3 which is based on the closing of spherical pores under the action of surface tension. The integrated form of this equation yields a straight-line relation between log (1 - D) and t. Such conditions were found by Felten4 to be true only after extended periods of pressing. In an endeavor to quantitatively evaluate the exactitude of this equation in the initial sintering stage, i.e., prior to sealing of the pores, spherical anti-

Jan 1, 1962

By A. Bascetin

Waste materials caused by mining activities are an important environmental problem. Paste technology is a good alternative for waste management because it has many benefits in the aspects of environment, cost and safety. Disposal of process wastes in paste form is an attractive option for waste management, as it eliminates or reduces the risks associated with conventional methods. Due to the geotechnical characteristics of the paste, it is very similar to soil materials. So determining the geotechnical properties of the paste material is essential to durability of the paste. The some important geotechnical properties are compressive strength, porosity, shear strength, hydraulic conductivity, water content, consolidation, etc. In this study, the important parameters and the relation between them were investigated and obtained some results which will affect for optimum design of waste management.

Jan 1, 2012

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the third report of investigations by the Bureau of Mines in cooperation with industry to establish the value of electrolytic manganese in the manufacture of ferrous and nonferrous alloys. The manganese was produced by the Bureau at its Boulder City pilot plant from domestic ores and by the process developed by it. 4/ The work was done under the direction of R.S. Dean, assistant director, Bureau of Mines, and R. G. Knickerbocker, chief, metallurgical branch. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steels 5/ and the second with its use in acid electric or open-hearth low- and medium-carbon steel castings. 6/The present report treats of the use of electrolytic manganese in the manufacture of low—carbon rimmed and killed steels. A résumé of these three investigations and two others appeared in the magazine STEEL. 7/ Further reports will be published as tests are completed at some 70 industrial plants. All tests were made on full—scale heats or melts, and the resultant product was processed and used commercially."

Jul 1, 1945

By Gary E. Sherman

Preliminary economic mining feasibility studies were conducted by the Bureau of Mines to estimate mining costs in the Juneau gold belt area of the Juneau Mining District, southeastern Alaska. Investigations were conducted on the economics of two mineral deposit types: (1.) Berners Bay vein gold deposits, and (2.) stockwork gold deposits containing gold, silver, and lead. Cost estimates were developed using the Bureau of Mines Cost Estimating System (CES). Discounted cash flow return on investment (DeFROI) was calculated using the Bureau's MINSIM computer program. Underground mining of a Berners Bay vein gold deposit was found to be economic (15 pct DCFROI) at a recoverable metal value of $353.67/mt for a 100 mtpd shrinkage stoping mine with a 10 yr mine life, $324.76/mt for a 20 yr mine life, $138.63/mt for a 500 mtpd longhole stoping mine with a 10 yr mine 1 ffe, and $127.50/mt for a 20 yr mine life. Block caving mining of a large stockwork gold deposit was found to be economic at a recoverable metal value of $15.28/mt for a 18,000 mtpd mine with a 20 yr mine life.

Jan 1, 2011

By Donald A. Bruce

Various types of contemporary Deep Mixing Method (DMM) techniques have been used in the United States since 1986. Such techniques owe their origins to Japanese and Scandinavian developments, which began almost three decades ago. The growing demands of urban infrastructure development and rehabilitation have created a very active and rapidly expanding market demand in the United States especially since the early 1990s, and there is a clear need for a new and fundamental review of the surprisingly large number of DMM techniques that are being used domestically, or are available in other parts of the world. Following a summary tracing the historical development of DMM, and a generic classification of applications, the paper provides a review of each of the many different proprietary methods, which the authors have identified during preparation of an international survey funded by the Federal Highway Administration (FHWA). Data are also provided on commercial aspects of the various DMM techniques worldwide.

Jan 1, 1998

Removal of Arsenic in Enargite from Copper Ores by Flotation and Leaching in NaHS Media

Sep 13, 2010

By G. F. Skala

Additional testing of two prototype instruments for the discrete detec­tion of submicrometer particles in metal and nonmetal underground mines is described. The detectors are designed to utilize properties of submicrometer particles to distinguish between those produced by fires from mine ambient particles primarily resulting from diesel engine exhaust. One instrument is based on the ability to pyrolyze fire produced parti­cles, but not diesel exhaust particles. An alarm is produced when the ratio of pyrolyzed to unpyrolyzed particles exceeds a preset value. The other detector utilizes a continuous flow ion chamber preceded by a denuder to remove charged particles. Discrimination against diesel produced submicrometer particles results because the diesel particles are naturally more highly charged than fire produced particles. In-mine testing was conducted over a period of several months. Both in­struments exhibited an ability to discriminate against diesel exhaust. However, problems with the recording equipment, and with the instruments themselves, due to large ambient dust particles, prevented enough data from being obtained to choose between the two methods. Recommendations to correct the problems are made.

Jan 1, 1982

By N. B. Devi

The extraction of copper(II) from sulphate solution was investigated using LIX®984N in kerosene. The parameters that could affect the extraction, such as equilibrium pH, extractant concentration, salt concentration, various diluents, and temperature, were separately investigated. On the basis of slope analysis, the complex formed in the organic phase is proposed to be CuR2, where R is the anionic part of LIX®984N. The extraction equilibrium constant and Gibbs free energy ( G) of the extraction process were determined. The positive value of H obtained from temperature variation studies showed that the extraction process is endothermic. The extraction of copper was lowest when chloroform was used as the diluent. Separation and recovery of copper from a synthetic copper-nickel solution containing 6.35 g/L Cu(II) and 0.58 g/L Ni(II) was carried out using 20%(v/v) LIX® 984N. The separation factor ( = DCu/DNi) was found to be pH-dependent. A two-stage batch countercurrent extraction was carried out at an O:A ratio of 3:4 at equilibrium pH 1.05 for extraction of copper from copper-nickel solution, followed by copper stripping from the loaded organic phase with 15% H2SO4 at an O:A ratio of 3:1.

Jan 1, 2014

By R. W. Watson, H. D. Peer

"This paper outlines the history of steel linings in the Autogenous Mills, the factors influencing the decision to convert to rubber lining, and the operating and cost experience with the rubber liners to date. INTRODUCTIONSherman Mine is an open pit iron ore mining, concentrating and pelletizing operation located at Temagami, Ontario. The operation employs 392 hourly employees and 81 salaried employees and has an annual capacity of over one million L.T. of high quality iron ore pellets produced from low-grade magnetite ore.The Sherman Mine is a joint venture; 90% owned by Dominion Foundries and Steel Limited (Dofasco) of Hamilton, Ontario, and 10% owned by the Tetapaga Mining Company, a wholly-owned subsidiary of the Cleveland Cliffs Iron Company of Cleveland, Ohio. The operation and management of the mine is by Cliffs of Canada, Limited. Development of the property was started in 1965, with pellet plant production beginning on March 17, 1968. At the present time, the orebodies contain sufficient reserves to sustain operations at current production levels for 30 years. Mining was originally carried out in three orebodies, the North, South, and West pits. The North Pit has been exhausted and mining operations ceased in the spring of 1980. A fourth pit, the East Pit, will be developed during the early 1980's."

Jan 1, 1981

Experimental Study of Ore Characterisation Methods for AG/SAG Mills Mining companies have long recognised the importance of ore breakage characterisation in design and optimisation of their crushing and grinding circuits. In one of the industry standard methods relevant to AG/SAG milling, ore is characterised using mainly high energy single impact tests. However recent DEM studies have suggested that breakage in AG/SAG mills is mainly due to low energy repetitive (or multiple) collisions rather than single high energy impacts. Hence a study was initiated at the JKMRC to investigate the behaviour of ores under such conditions. Carefully designed experiments have been performed using two laboratory mill sizes (0.6 m and 1.1 m diameter) to mimic the reported low energy repetitive impact breakage under low load conditions. The breakage characterisation parameters derived from standard high energy single impact tests on the same ores was then used to predict the low energy repetitive impact breakage. Significant bias was found in the simulations which clearly warranted further investigation. The extensive experimental program which followed employed three separate methods: the JKRBT (JK Rotary Breakage Tester) for high energy single impact and low energy repetitive impacts, gravity drops for low energy repetitive impacts, and laboratory mills to provide an extended number of low energy repetitive impacts. The breakage energies associated with these experiments were accurately measured with a high speed video camera. Two breakage indices, the degree of breakage (t10) and the breakage probability (S) were used to describe the breakage test results. This paper summarises the major results from this experimental study, which has facilitated the development of a new breakage characterization method relevant to AG/SAG mill modelling.

Sep 13, 2010

By John S. Hutchins, David L. Wassum

Mining engineers are ready to take a big step into a new field-oil mining. To understand the subject, one must look at the world's oil supply and demand as well as petroleum technology successes and failures. The US has an abundance of solid hydrocarbon and uranium energy resources, but 75% of its energy for industry, transportation, manufacturing, and space heating comes from liquid petroleum and natural gas. So there are increasing efforts to discover new oil reserves; today the number of drilling rigs operating in the US is at an all-time high. But with 80% of the world's wells already located in the US and Canada, good new exploration prospects are difficult to find. The cost of drilling deep new wells has also greatly increased. The US faced a similar situation in the early 1950s, when primary oil production declines began. During that time, the petroleum researcher introduced secondary recovery techniques such as water flooding and gas injection. This increased the average amount of extractable oil from discovered US reservoirs from 17% to 33%. Production soared and the world petroleum price remained stable until the end of the 1960s. Secondary recovery techniques were then supplemented by tertiary oil recovery technologies-increasing sweep efficiency with such things as CO2 injection-that are, so far, only partially successful in most petroleum fields. Even so, these technologies could raise cumulative recovery expectations to 35-38%. The "lost" oil in depleted US reservoirs equals 48 km3 (300 billion bbl) of conventional oil, or 12 times the current recoverable reserve base. At the present rate of US consumption-1 km3/a or 6 billion bbl/a-this is enough to run the US for 50 years without importing any oil. Moreover, there are 16-24 km3 (100-150 billion bbl) of as-yet unrecoverable heavy oil and tar sands in the US.

Jan 12, 1981

By Arthur A. F, MacKenzie I. H

Copper in zinc/lead sinter charged to the Imperial Smelting Furnace operated by Sulphide Corporation Pty Limited at Cockle Creek, New South Wales, concentrates in a complex lead dross which forms as the bullion is cooled to around 400°C. The 0.35 mm portion of this dross, containing approximatelY 67 per cent of the total copper, is treated via a hydrometallurgical route to produce 5000 tonne/yr of CuSO4 5H2O crystal.Around 3000 tonne/yr of copper-lead dross containing 49 per cent copper is leached at 55°C in continuous leach reactors with ammoniacal ammonium carbonate leach liquors to convert copper to soluble copper amine complexes. Leach ettlciencies of 80-85 per cent are obtained. Leach residues are repulped with ammoniacal liquid diluents from the plant and heated in a four stage steam distillation unit to reduce ammonia levels to between 0.5 and 1.0 g/Iitre. The resultant slurry is directed to an effluent treatment plant for final treatment, and separation and return of solids to the sinter plant.Copper is extracted from leach liquor by solvent extraction techniques based on the use of L1X 54 diluted 3:1 with Shellsol 2046 to give a nominal copper loading of 30 g/litre. The loaded organic is contacted with a sulfuric acid solution of pH 5 to remove the bulk of ammonia and zinc, then stripped at 55°C with a 60 g/Iitre H2SO4 95 g/Iitre copper solution to yield a 15 g/Iitre H2SO4 125 g/Iitre copper solution.This liquor is fed to an adiabatic vacuum crvstalliser operating at 35°C and 5 kPa vacuum where crystals of CuSO4 5H2O are formed. Crystals are separated from mother liquor and washed in a two stage pusher centrifuge, then dried in a hot air rotary drier. The crystal product obtained is of a high chemical purity and readily conforms to both Australian and overseas standards.

Jan 1, 1983

By Avery H. Reed

[The Bureau of rides is making a general study of the occurrence of the Clinton red iron ores of Alabama. In the course of this study, it developed that the iron-ore seams of the Woodstock and Bucksville areas were virtually unexplored., and the nature and extent of the ore deposits were undetermined. As a part of the work of the project, the Bureau investigated the occurrence of red iron ore in the .areas. Eighty-four channel samples, representing 317.6 linear feet, were taken from l2 locations along the outcrop of the red iron-ore seams, Ten diamond-drill holes, amounting to 3915.5 linear feet, were drilled. In these areas, commercial- and marginal-grade ores of minable thickness have been shown. It is estimated that 4,500,000 tons of indicated ore and 6,700,000 tens of inferred commercial-grade ore averaging 5.1 feet thick, 47.6 percent Fe, 26.1 percent insoluble, 0.1 percent CaO, and 0.04 percent P; 7,200,000 tins of inferred marginal grade ore averaging 6.1 feet thick, 36.2 percent Fe, .35.0 percent insoluble, 3.9 percent CaO, and 0.14 percent P; and 18,500,000 tons of ferruginous sandstone averaging 12.2 feet thick, 19.2 percent re, 50.1 percent insoluble, 9.6 percent CaO, and 0.14 percent P are present in the areas.. All tonnages are estimated as gross tons of recoverable ore in place, based' on 65-percent mining recovery. In accordance with established policy of the Bureau of Mines of publishing factual data as soon as possible after completion of field work, this description of the Woodstock and Bucksville areas is presented. As soon as work is completed in other areas additional reports will be prepared.]

Jan 1, 1953

By Ronald M. Hays

The White Pine Copper Division of Copper Range Company is a large copper producer operating an underground mine, mill, and smelter on Michigan's Upper Peninsula. Principal water discharges are from the tailings basin where these discharges are high in dissolved solids because of mine water pumped into the basin. Principal air emissions are from the smelter where SO2 emissions are uncontrolled. Although water discharges and air emissions have not had significant environmental impacts, environmental regulations could require additional control procedures. Because of low copper prices and poor profitability, cost of compliance with possible new environmental regulations could have serious impact on White Pine with no apparent significant beneficial environmental impacts.

Jan 1, 1979

By S. J. Jung

The most frequent causes of accidental injury and fatality are carelessness and ignorance; and the most common accidents are haulage accidents, fall, drowning, and fire. However, in this modern day and age, severe injury has become the dire consequence of an ever-increasing number of industrial and mining accidents as well as sport-, military- , etc. Mine accidents have declined dramatically in number and severity through decades of research, technology, and preventive programs. However, preventing recurrence of disasters like those of the past remains a top priority requiring constant vigilance by management, labor, and government. The goal of the present research is to investigate and identify root causes associated with types of mining accidents (victim being caught by an equipment, bodily motion, over exertion, etc) and nature of injuries such as (sprain and strains, fracture, dislocation, amputation, etc). Further, we hope to discover the impetus of the root causes occurring more and more often in this modern day of technology and quality awareness. With the different dimensions of accidents and injuries brought into the fold, there is the need for researchers and mining operators to comprehend and better still visualize significant patterns of associations among these variables of interest. We assume that, there is a high correlation between many dimensions of nature of injuries and types of accidents. This suggested a principal component analysis to reduce the dimensions for easy and amenable interpretation.

Jan 1, 2012

By Fred C. Schmednecht

For years, the strategy was to contain waste and in many applications, is still the recommended method. Recently, it has become acceptable to create filters below ground for the in-situ treatment of waste. Consequently, in lieu of the waste being contained, it is desirable that the waste flow through a pervious treatment zone. For instance, subterranean pervious walls comprised of iron sand are particularly useful in treating chlorinated solvents in contaminated groundwater. The iron acts as a corrective filter to treat the contaminated groundwater. How are these impervious and pervious walls being constructed? One effective means of constructing an impervious barrier is the vibrated beam method. This method, in brief, involves the use of a fabricated steel beam, a vibrator, a pile driving crane, and a mixing plant. This method results in a 4-6" wide wall with depths up to and exceeding 100'. Over one hundred slurry walls have been installed using this method in the United States. The need for the vibrated beam method continues to escalate due to its reduced health and safety considerations, high level of quality control, lack of excavation, narrow working area, and ability to achieve depths greater than 100'. A recent project was in Marinette, Wisconsin at the ANSUL facility. The project consisted of a 28,000 square foot slurry wall and was completed in January of 1999. Another effective means of creating an impervious barrier, where structural support from the barrier is needed, is the Waterloo® Barrier System. This system involves the use of a pile driving crane, Waterloo® steel sheet piles which are patented steel sheet piles due to their groutable interlocks, and a grout plant. This system results in a water-tight barrier due to the grouted interlocks and provides structural support. A project was completed at Beta Steel in Portage, IN for a retention pond to protect Lake Michigan. Due to the new concept of "filtering", there are few accepted construction techniques available. One effective field proven construction technique is the patent pending mandrel emplacement technique. This technique involves the use of a fabricated hollow steel mandrel with a shoe, a vibrator, a heavy duty crane, and a material feeder. This technique results in a pervious wall which may be comprised of pure iron sand or any other flowable media. Using this technique, the pervious wall may be constructed in varying widths to depths in excess of 100'. A successful installation occurred in October 1997 at Cape Canaveral Air Station in Florida.

Jan 1, 1999

By H. Tudeshki, A. Tayebi

"The large extent of global production and consumption of aggregates from quarries, grabs one´s attention and makes its substantial and essential standpoint in the world today pretty clear. A great amount of aggregates is utilized in civil engineering applications such as road construction, railway industry, concrete production, etc. Considering this fact that igneous rocks display a higher strength and abrasion resistance, this type of rock is preferred in the field of civil engineering. For all these applications, rock quality assurance is a key factor and certainly unavoidable, and it has great influence on the quality of constructions in civil engineering. One of the major problems encountered by both the producers and users of igneous rock is the fact that, with the passage of time, some specific rocks lose their strength, up to a complete loss of structure or in other words, their disintegration and degradation. In the last decades, different methods and procedures such as Glycol test, methylene blue dye test, as well as the Los Angeles test have been introduced to distinguish these rock properties, and to identify these problems. However, as these methods are time consuming, hard to perform, only to be applied to hand-piece samples, requiring special laboratory equipments, and only possible to be accomplished under laboratory conditions, their application has always been limited to some specific cases, and they are neither recommendable nor advantageous. In addition, these methods provide partially different results for the same rock. To address this widespread quality management problem of the quarry industry, a relatively quick, easy and user-friendly approach is necessary. It calls for a systematic solution with a device that can simply be used day to day in a mine for quality control of the quarry´s daily production. This scientific research is concentrated on developing a systematic method for early recognition and diagnosis of rock quality, in order to control and manage the quality of the quarry production in advance. This method was developed, based on the procedure of the magnetic susceptibility measurement. The obtained values can lead to valuable information regarding the quality of the rock and allows the quality control process to be accomplished and performed at the borehole location. This approach has been assessed through extensive field and laboratory studies. A detailed and comprehensive discussion will be made on the results of the experiments. The advantages and impacts of the application of this method, on increasing the reserves and environmental protection are also discussed."

Jan 1, 2011

By J. R. Long, A. H. Roberson, T. R. Graham, R. S. Dean

EXPERIMENTAL work on the properties of high-purity alloys of the copper-manganese-zinc system has necessarily required extensive metallographic work to determine the equilibrium conditions in this system. Previous work on these alloys is fragmentary and, unfortunately, based on alloys made with impure grades of manganese, thus introducing significant amounts of iron, silicon, aluminum and carbon. Since these elements are known to affect equilibrium conditions, it became desirable to re-examine these alloys made from the pure metals. The alpha solid solution field was of particular interest and, therefore, was chosen for the initial work, which was outlined to determine the composition limits of this field. PREVIOUS WORK Heusler1 conducted an extensive survey of the liquid-solid regions of this system and also made an estimate of the solid-phase boundaries at 340°C. The pertinent part of his diagram is given in Fig. I, but it is of limited usefulness, since it applied to a single temperature only and is based on impure alloys under admittedly nonequilibrium conditions. Bauer and Hansen,2 likewise working with impure alloys, have determined the phase boundaries for alphabeta brasses containing small amounts of manganese and indicate an increase in the extent of the alpha field with increasing manganese. This is not in accordance with Heusler or with data obtained on pure alloys.3 They also described a third constituent precipitating in the alpha plus beta field below 350° to 400°C. but did not identify this constituent. Guillet4 and Heike and Ledibur5 have also noted this precipitate Each of these investigators recognized that impurities present in the manganese could and did have an effect on the structure and properties of their alloys. Corson6 in particular pointed out the hardening effects of silicon, aluminum, and carbon in copper-manganese alloys and Heusler reported that his alloys containing more than 25 per cent manganese were extremely brittle. In all probability this brittleness was due to the impurities present. This early work, therefore, should be taken as a general guide for preliminary studies only, and high-purity alloys may be expected to produce different results. The work of the Bureau of Mines laboratories with electrolytic manganese has been briefly summarized by Dean7 but includes only a short section on this system. Later work3 outlined a limited portion of the alpha field in the neighborhood of 65 per cent copper, 10 per cent manganese, and 25 per cent zinc. The present work was under-

Jan 1, 1945