Search Documents

By R. G. Vardiman, M. R. Achter

Observations of dislocation structure in niobium are presented using two techniques. Triangular pits developed by electroetching are confined to orientations in the stereographic triangle between the (111) pole and planes of the (1ll) zone and require the presence of carbon. Some unusual electroetching phenomena at other orientations are noted. A chemical etch of dislocations decorated by the addition of carbon to 50 ppm reveals the complete dislocation line structure in a surface layer up to 30 p deep, with a resolution of less than 1 p. This effect is independent of surface orientation. The structure of subboundary nets may be resolved for misorientations up to about 1'. Dislocation structures found in strain anneal grown crystals, such as helices, prismatic loops, and high-density areas, are observed. The measurement of dislocation density is discussed and values obtained in different ways are compared. IN the course of some work on the response of refractory metals to thermal-mechanical treatments, it was desired to examine the defect structure of relatively low dislocation density crystals of niobium in bulk form. Surface and bulk methods for the observation of dislocations have been reviewed by ~melinckx,' and include etch pitting, decoration, and various X-ray techniques. The dislocation line structure has been developed by decoration in a few metals, although observations were limited to certain orientations, or by the coarseness and nonselectivity of the precipitate. The most commonly used technique is etch pitting. In niobium, etch pits have been developed chemically'0," in material of high impurity content and electrolyti-cally'' in relatively pure material. In this paper, etch pits developed electrolytically, and the dislocation line structure of a surface layer developed by decoration and chemical etching, are examined, and observations are presented from both techniques. EXPERIMENTAL METHODS Our starting material was electron-beam-melted niobium, swaged to 4 or -in.-diam rod. Chemical analysis is given in Table I. Single crystals were grown by a strain anneal technique using 1 to 2.5 pct of strain and growth temperatures of 1700" to 2300"~.'~ Some crystals grown by zone melting were also examined. The desired surface orientation was exposed either by spark machining or by sectioning with a cut-off wheel and prepared for etching by electro-polishing.

Jan 1, 1969

By David Bigby

In the UK, it is becoming increasingly necessary to open new longwall mining areas above old, abandoned workings. In such cases, strategic and gate roadways must often be driven and maintained across highly stressed areas and pre-existing and sometimes only recently formed subsidence troughs. Ground control at the edges of the subsidence trough can be particularly problematic, with complex combinations of stress and rock conditions being encountered depending upon the precise position in relation to underlying pillar edges. For economic recovery of these reserves, it is essential that rockbolt support is used wherever possible. It is therefore very important to the industry to develop its understanding of ground conditions and support requirements in these areas. This paper describes; ? the historical background to these problems and a series of documented UK case studies from the last 20 years. ? the experiences at UK Coal?s Riccall colliery, where a number of longwall panels were worked at a depth of around 800m, some 65m above previously worked longwalls. Actual experience is compared with pre-mining expectations and model predictions. ? design considerations and experience to date at UK Coal?s Welbeck and Thoresby collieries, which are embarking upon a series of longwalls in the Deep Soft seam, 30-40m above previously worked longwalls. The paper outlines numerical modelling techniques used to optimise such mine layouts within the complex geological and geometric constraints of a mature coalfield. These involve combinations of 2D and 3D finite difference and 3D boundary element models. It also discuss new modelling approaches which will be investigated in forthcoming EU funded research.

Jan 1, 2007

By Marcelo Fernandes Mercier

A presença de inclusões nos aços está diretamente associada à sua limpidez, sendo que os diferentes tipos de inclusões não-metálicas podem prejudicar desde o processo de fabricação e conformação até as propriedades finais do aço exigidas para a sua aplicação. As inclusões se formam e se modificam ao longo do processo produtivo, e estão relacionadas principalmente às técnicas de refino secundário e lingotamento contínuo. Neste trabalho será desenvolvido um método de cálculo para a adição de CaSi em função do seu rendimento, nível de oxidação, composição química e temperatura do banho, objetivando atingir a “janela líquida” do aço. Espera-se que o cálculo da quantidade de CaSi a ser adicionada (atualmente utilizase uma taxa fixa) nos aços durante o processo de rinsagem, conduza, com mais segurança, a obtenção de inclusões líquidas e consequentemente uma melhor limpidez do produto.

Aug 8, 2018

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966

By John J. Vieaux

Allowable loads on Dynamically-Cast-In-Place Piles (the Franki type) can be correlated with N values from the Standard Penetration Test. Using a constant developed by Nordlund, a conservative value for load-carrying capability of a DCIP pile is developed. The DCIP pile and method of installation is briefly described.

Jan 1, 1984

By R. L. F. Kay, T. A. Fletcher, A. J. Boyce, C. M. Rice

Paper presented at Mineralisation in the Caledonides, the Mike Gallagher memorial meeting held in Edinburgh, 27-28 June 1996. The synorogenic, mafic Ordovician intrusion comprises orthopyroxene-rich xenoliths and mafic-ultramafic cumulates with low-grade pyrrhotite, chalcopyrite and pentlandite mineralisation. Despite abundant textural, mineralogical and O isotope evidence for significant assimilation of country rocks, S isotopes indicate only a modest uptake and suggest that mineralisation is dominated by magmatic sulphur. The preferred explanantion is that the magma was close to S saturation on emplacement. Uptake of elements such as Si and O led to early crystallisation of orthopyroxene, resorption of olivine and early segregation of a sulphide liquid. Post-magmatic interaction with a high-temperature, surface-derived fluid, whose movement may have been controlled by regional shear zones, reset biotite and whole-rock O isotope values but not those of orthopyroxene. This model identifies the presence of olivine-rich rocks and evidence of extensive assimilation as guides to prospectivity

Jun 19, 1905

These proceedings consist of an overview of the in situ mining research currently being carried out by the Bureau of Mines. The following papers emphasize two general aspects of the in situ mining method: the environment and productivity. Both areas are extremely important, particularly because in situ leach mining is a relatively new mining method from a commercial point of view. Topics covered include the restoration of ground water, the selection of lixiviants, in situ mining of commodities other than uranium, in situ mining costs, the application of resistance measurements to in situ mining, an acid leach mining case history, and the use of branched boreholes for in situ mining. A bibliography of Bureau of Mines publications on in situ mining is appended.

Jan 1, 1981

By W. J. Miles

Many years ago, a relationship was established between dust inhalation and pneumoconiosis. Since then, various government agencies have regulated crystalline and amorphous forms of silica material in the workplace. In 1987, the International Agency for Research on Cancer (IARC) classified crystalline silica as a probable carcinogen. With this listing, crystalline silica became a regulated substance under the Hazard Communication Standard. The minerals and chemicals industries have responded in various ways. They have: • developed worker and user training programs and literature; • labeled products with appropriate warnings; • continued to implement dust reduction programs; and • developed meaningful epidemiological studies of workers. • begun development of reliable analytical methods for measuring crystalline silica at the 0.1 % threshold level; Background Silicosis historically has been the major health hazard resulting from exposure to crystalline silica. Silicosis is the scarring of the lung from excessive exposure to crystalline silica. It has been recognized as an occupational disease for more than 2000 years, since early Greek physicians noted the respiratory problems of miners, stonecutters, and quarrymen who were exposed to excessive quantities of mineral dust. During the industrial revolution, the incidence of the disease was greatly increased by the use of machinery that increased dust levels. Subsequently, the need for dust control was recognized and measures were instituted. Silicosis is characterized by progressive breathlessness on exertion and develops over the course of years. Xray images of the lungs show

Jan 1, 1990

By James J. Cahill

Contractor's working in an urban environment face a multitude of working conditions. There is no typical "Downtown" job site. From afar we just see the skyline, or up close a specific building. This, of course, does not give us a clue as to the site conditions the foundation contractor faced in doing his work. The open, downtown building site is still available on some projects, but they are becoming rare as our cities are becoming more developed. A typical site today might include any one or several of the following problems: A. Deep pit with no ramp access B. Multi-type known or unknown obstructions C. Height limitations D. Load restrictions E. Existing adjacent building founded on shallow foundation F. Existing foundations G. Existing tunnels, utilities or subways

Jan 1, 1991

By G. L. Oldright

The studies previously made on Smelting in the Lead Blast Furnace have dealt with the custom smelter of the International Smelting Co. at Tooele, Utah,4 and on the smelter of the Bunker Hill & Sullivan Mining & Smelting Co.5 at Kellogg, Idaho. The International plant may be considered representative of the traditional custom smelter. The lead smelter of the future seemingly will have to treat increasingly richer lead charges. This feature was then stressed in describing the Bunker Hill plant.

Jan 1, 1934

By G. E. McElroy

The purpose of tins paper is not to present new date on the pressure losses due to bends and chances of area in mine openings through which air flows, but rather to correlate existing data, determined mainly on small duct systems and expressed in a variety of ways, according to uniform methods that facilitate their use in pressure-loss computations. These are required in such, air-flow problems as determining the quantity that will flow through is mine openings under a certain pressure difference or, conversely, the pressure difference that will be required to maintain a certain rate of flow. Air flowing through h ducts, such as mine airways, encounters resistance to flow due to interference of the individual air streams with each other caused by the wall surfaces. The result is that part of the kinetic energy of the flowing stream is converted to heat; and constant renewal of the kinetic energy from the total energy of the flow is required to maintain it. This process manifests itself by a decrease of the total pressure (static pressure plus velocity pressure; of the air in the direction of flow; in order that flow pray occur, there must necessarily be a differences in total pressure between the two cads of the air-ay equivalent to the pressure losses occasioned by the flow, which automatically adjusts itself in magnitude to the pressure difference maintained.

Jan 1, 1932

By Gene F. ] [Faufaul

This contract was concerned with the design, development, fabrication and testing of an improved tamper-proof filter cassette assembly for use in the, collection and evaluation of dust particulates, primarily in mining areas. This report presents the design effort, fabrication and tenting of five- prototypre unit$ as well as the design and production of 1000 filter cassettes with sampling heads. This new improved filter cassette has been tested and approved by NIOSH as meeting the requirements specified in the contract.

Jan 1, 1978

By B. Jago

From the perspective of metallurgical processing, gold ores can be classified into freemilling and refractory ores. Their extractive metallurgy is largely driven by mineralogical factors such as gold particle size, association with other minerals, coatings and rimmings, presence of cyanicides, oxygen consumers and preg-robbers, presence of refractory gold minerals, and invisible gold in sulphide and sulpharsenide minerals. Gold process mineralogy helps address issues and problems related to gold ore processing. It is widely used as a predictive and trouble-shooting tool in gold ore processing, and provides useful information on process selection, flowsheet development, recovery improvement, and reagent consumption optimization. By combining classic mineralogical techniques, modern instrumental analysis, and diagnostic metallurgy, the mineralogist is able to balance the various types of gold occurrence in an ore.

Jan 1, 2006

By J. I. Paige

As part of a continuing effort to develop technology that maximizes mineral and metal recovery from domestic resources, the Bureau of Mines investigated a method to totally utilize copper converter slags without recycling them back through the matte smelting furnace. The research was directed toward (1) recovering the contained copper in converting slags by producing a recyclable copper-iron matte, (2) carbothermically reducing the slags to recover the iron, and (3) producing slag wool from the depleted slags. This report deals with the reduction of three industrial converting slags, containing 2.0 to 7.3 wt-pct Cu, in an 800-kVA electric arc furnace to produce a recyclable copper-iron matte. The addition of sufficient iron pyrite to provide 29 to 113 pct of the stoichiometric sulfur (based on producing 40-pct-Cu matte) produced a recyclable matte (36 to 61 pct Cu) at an energy consumption of 520 to 700 kWh per ton of solid material charged. The expected energy saving for treating molten slag in an electric furnace (5-to 9-MVA range) is about 400 kWh per ton of molten slag treated.

Jan 1, 1982

By S. F. Radtke

The properties and characteristics of lead and zinc have made these metals useful to man in many ways since the days of antiquity. Despite their long history of use, however, these metals have proved to be extremely resilient and responsive to modern needs. New alloys and compounds continue to be developed, adding to the growth of these metals. Consumption data is given for 1969 and compared with one and two decades ago. Trends in major markets also are cited and explained. Uses for lead and zinc which have come into prominence within the past few years are described and explained, with emphasis on the role played by the industry's cooperative research program. Current efforts in the research phase are discussed, with details given on major efforts for both metals, including new alloys, process developments, applications research, finishes, coating, paints and pigments, batteries and fundamental research. A forecast is given of promising new areas and a projection made on a longer term of new applications that may emerge from current research.

Jan 1, 1970

By William C. McBee

Sulfur concretes have been developed by the Bureau of Mines as construction materials with physical and mechanical properties that suit them for use in acid and salt corrosive environments where conventional concretes fail. Mixture design methods were established for preparing sulfur concretes using different types of aggregates and recently developed mixed-modified sulfur cements Bench-scale testing of the sulfur concretes has shown their potential value. Corrosion resistance, strength, and durability of sulfur concrete are superior to those of conventional materials. Field in situ evaluation tests of the sulfur concretes as replacement for conventional concrete materials are in progress in corrosive areas of 24 commercial chemical, fertilizer, and metallurgical plants.

Jan 1, 1983

By Fisher N. I

Disequilibrium ratios (U3O8/eU3O8), which assess the degree to which gamma activity represents the uranium content of a sample, have been measured on a representative set of samples from the ore zone of a carnotite ranium deposit located at Yeelirrie, Western Australia. A statistical analysis has been performed to investigate the dependence of the ratios on lithology and on the location of the sample in the orebody. The analysis indicates that dependence on lithology and on position across the orebody is negligible. Samples from the western end of the orebody and those from below the water table level tend to have slightly lower ratios than samples from other positions, although these trends are small compared with a large random variation in the data. The large random variation could result from some redistribution of the daughter isotopes of uranium within the orebody. On the basis of the results from all the samples, the estimated deficiency of uranium relative to radium in the ore zone of the deposit is 11 per cent.

Jan 1, 1980

By D. Mohapatra

The possibility of using 2,2,4-trimethyl-1,3-pentanediol dissolved in tetrachloromethane as extractant for boron recovery is discussed. The parameters optimized for this purpose are contact time, boron concentration in the aqueous phase, extractant concentration, equilibrium pH and phase ratio. NaOH is used as stripping agent for boron recovery from the loaded organic phase. Boron extraction is found to be a slow process (equilibrium time 20 minutes) compared to boron stripping, which is reasonably fast (equilibrium time 5 min). Maximum boron extraction is possible at a broad pH range from 1.0 to 6.0. Using 1.0M extractant concentration, a 1:1 phase ratio (organic: aqueous) and two stages, ~99% boron extraction is achieved. More than 97% boron stripping is possible using 0.5M NaOH at a 1:1 (organic: aqueous) phase ratio in two stages. Overall, a 95.6% boron recovery was achieved. Loss of solvent into the aqueous phase and co-extraction of Ca, Na and K into the organic phase at higher equilibrium pH are two major concerns in his process.

Jan 1, 2008

bauma 2004 will feature a couple of firsts for one of the world’s largest construction and building materials machinery exhibitions. The event is scheduled for March 29 through April 4 of next year at the New Munich Trade Fair Center in Munich, Germany. For the first time, bauma will feature an exhibition area dedicated to mining equipment and technology. Also for the first time, the Commonwealth of Independent States (CIS) will be a partner region of bauma.

Jan 1, 2003

If the industry keeps doing what it has always done, it will continue to get what it has always got - rising operating costs. Why is this so? Generally grades being chased are becoming lower, stripping ratios becoming higher, ability to attract personnel to the industry becoming harder and/or more expensive, higher safety standards are being demanded and environmental governance is being enforced.   How then should the surface mining industry plan for the future whilst delivering on improved safety and the environment? In-pit crushing and conveying (IPCC) points the way, as a partial or complete substitute for trucks.   IPCC systems promise significant advantages over traditional truck and shovel operations, including improved safety, reduced operating costs, reduced dust and noise emissions, far greater efficiency in energy use (electric versus diesel motors predominantly and the ability to regenerate electricity back into the local grid for downhill situations), reduced carbon emissions (dependent on power generation source) and reduced water consumption. Despite these advantages, there is a general industry reluctance to migrate from truck and shovel operations. This reluctance stems from a familiarity with truck and shovel operations and a perceived concern that IPCC lacks flexibility which will negatively impact on the mining operation.   In studies conducted since 2007 (with the new modular builds) comparing IPCC with truck-optimised pit designs, IPCC has delivered up to USD$0.82 per tonne moved less than an equivalent truck operation. In addition, IPCC is easily automated from a central control room (local or remote) - something that trucks have yet to commercially achieve.   IPCC is a proven process that, with a fresh mindset, can make a significant improvement to mining operations - its safety, the impact on the environment and its costs. It maybe of interest to note that there is over 200 IPCC installations worldwide today.   This paper and presentation will assist in furthering the understanding of IPCC and its applicability.

Jun 1, 2010