Search Documents

THOUGH the literature on the chamber process is considerable, it mostly refers to European conditions. Owing to the demand for acid for flotation and leaching at the mine, it may be necessary to work the process under other conditions. Consequently, some results obtained during the chlorination days at Mount Morgan, within the Tropic of Capricorn, may be useful for reference when working in a similar climate. Though the chambers must be protected against tropical storms, thorough ventilation should be provided, with plenty of space between the chambers, which are almost invariably crowded together. Not only does the space assist in the cooling of the chambers, but it is very desirable during repairs, when lead andtimber have to be hoisted up. The connecting flues between the chambers, which are fairly efficient mixers and condensers, should be round, supported from above, and with the least possible timber about them. Their position and arrangement deserve careful attention. Lattice work will be sufficient protection for the sides of the chambers, and the roof should be high and well ventilated. The Mount Morgan plant, crowded and not well situated, consisted of seven chambers (four over 50 ft. in length), one Glover tower 7 ft. 2 in sq. x 20 ft. high, one Gay Lussac 9 ft. sq. x 30 ft. higb, also one 5 ft. diam. x 25 ft. high. There was one pipe column 4: ft. sq. x 14 ft. 6 in. high. The chambers were run as one unit, and were much lower than those usually constructed in Europe-less than 15 ft. high. Provided that suitable timber can be obtained, 20 ft. is quite low enough. It should be quite satisfactory to use round poles for the studs, and so admit more air space between studs andlead.

Jan 1, 1920

Underground Mine Drainage may be conveniently divided into two operations:(a) Collecting and transporting drainage water to the pump eastern.(b) Elevating water to the surfacc by pumping.This short paper describes a system which automatically performs operation "a" and which has been developed on the South mine at Broken Hill, under the supervision of the mine foreman, Mr. F. McDonell. Operation "a" does not come under the heading of "subsidiary mine" drainage.SUMMARY(1) All drainage waters are collected by gravity flow into sumps.(2) Automatic control boxes operate syphons which transfer water from level to level to pump cisterns or to feed water service.EQUIPMENTSyphon Control Boar - Constructed of 10 ft. x 2 ft. oregon timber, suitably bolted together and equipped with a Bailey's cistern valve, with copper ball float control, and 12 in. pipcs and fittings forming a syphon (Fig. 1). One of these boxes is placed on each level at the shaft.The valve and float are so arranged that when the float is up (ie, box full) the valve will be fully open, and when the float is down (ie, box empty) the valve is closed. The vertical range between the cxtreme positions can be altercd by lengthening orshortening the adjustable arm of the float. The ideal valve is one...

Jan 1, 1927

By R. A. Strehlow

This is the final report for U.S. Bureau of Mines contract HO-122122, which was in effect from June 30, 1972 through January 4, 1976. The work resulted in the design and construction of a large laboratory scale coal dust burner and the use of this burner to study gaseous and coal dust flammability. A new technique for determining gas phase flammability was developed and the effect of solid and gaseous suppressants on the propagation of coal dust flames was studied. In addition, a technique for measuring the C/H ratio in the flame was developed and the C/H ratio that was measured in a coal dust flame on this burner showed that the burning process was preceeded by pyroysis of the coal dust. Both experimental and theoretical studies showed that radiative trans-port is very important to the propagation of a coal dust flame.

Jan 1, 1977

By Max F. Lee, Warren A. Peck

The applicability of the Q-system [Barton et al. 1974] to Australian underground metal mines is discussed with reference to two common design issues: ground support for horizontal mine development, and assessing the stability of bored raises. Installed ground support in mine development is com-pared to empirical estimates using the Q-system and associated support capacity calculations. Data are graphically presented from 59 specially selected sites at 15 contributing mines. The actual performance of large-diameter raise-bored shafts is also compared to empirical stability assessments using a modified version of Q (Qr, after McCracken and Stacey [1989]). Lower-bound Qr values are plotted against raise diameter for 47 selected sites at 23 mines in Australia and Papua New Guinea. The influence on Q and Qr of some geotechnical aspects of the Australian landscape, the dynamic nature of mines (compared to civil construction), and occupational health and safety regulations are discussed. Stability and support assessments that are based just on Q or Qr are not always conclusive. It is often necessary to consider other rock mass parameters, the regulatory environment, and risk issues. These results are interim; further data collection and analysis are required with regard to comparing actual performance versus empirical assessments.

Jan 5, 2007

By Browner R, Lincoln F. J

The activity of silver in solid gold-silver alloys (electrum) has been measured with an electrochemical concentration cell based on the super ionic conductor silver-i3-alumina in the temperature range 200 to 80oaC.The measurements of the silver activity in the range 0.5 to 90.0 atom per eent silver were found to be highly reproducible although there is some disagreement with an earlier study which used a similar technique. At temperatures above 400° the silver activity exhibits both positive and negative deviations from ideality in the silver rich region.This method suggests a simple technique for the nondestructive determination of silver in electrum alloys.

Jan 1, 1983

By D. Shin

The gold leaching using cyanide from ore or waste has been almost universally in use [1]. Recently, biological gold bioleaching using cyanide producing bacteria, e.g. Chromobacterium violaceum, Pseudomonas fluorescens, or P. aeruginosa, has been investigated as environmental friendly and cost effective method. Among them, C. violaceum has been reported as effective cyanide producing bacterium on gold leaching [2, 3]. C. violaceum produces cyanide using glycine as a direct precursor and subsequently detoxify the cyanide by ß-cyanoalanine synthase [4]. However, until today only 0.026 ? 16.9 mg/L of cyanide production in YP medium has been reported in the literatures by C. violaceum [4-6]. Comparing with adding cyanide chemical, biogenic cyanide concentration is lower than the cyanide concentration added in traditional cyanidation. Since cyanide also forms complexes with a number of other elements such as iron, nickel, zinc, silver, copper, and platinum, it is very important for gold recovery to investigate the enhancement of biological cyanide production and set optimal experimental condition. Most of early studies on gold bioleaching by C. violaceum have been performed to investigate gold leaching mechanism using gold powder, and recently various resources such as ores, electronic scrap, and printed circuit boards of waste electronics [7]. Few studies have dealt with gold bioleaching from low-grade ore. In this research the feasibility of gold bioleaching by C. violaceum from low-grade ores containing gold was evaluated and fundamental study was performed for further scale-up study. The aim of this study was to improve the potential of gold bioleaching by C. violaceum from gold-containing ore; in particular, enhancement of biological cyanide production.

Jan 1, 2012

By M. Faraji

Inclusions formed in a high-carbon, manganese-silicon killed plain steel (Fe-0.77C wt%) were studied. Various techniques were used to characterise the inclusions, and the latter were classified according to their chemical composition, size and morphology. The main constituent elements entering the inclusions were Mn, S, Al, and oxygen. Alongside MnS and some Al2O3 inclusions many non-metallic inclusions appeared in complex forms, consisting of silicates, sulphides and oxides. Duplex oxy-sulphides, mainly MnS combined with Al2O3, or SiO2 were the most common complex multiphase inclusions in this steel. The nanoindentation technique was used to assess and rate different types of inclusions and data of the hardness and elastic modulus of individual inclusions at room temperature are presented.

Jan 1, 2010

By William H. Pomroy

Fire on surface mining equipment is a serious hazard to life and property. The Bureau of Mines, through a program of contract and in-house research, has developed and in-mine demonstrated reasonably priced, reliable automatic fire protection systems to deal with this problem. This report reviews the development and subsequent testing of systems for haulage trucks, front end loaders, coal augers, dozers, drills, and shovels. A variety of fire sensors, extinguishing agents, and control systems arc discussed in the context of mine equipment designs and operating environments

Jan 1, 1980

The passage of chloroform vapour in a carrier of oxygen through two nickel sulphide ores heated to 380°C converted the nickel to the water soluble chloride form. In one ore the nickel (2·75 per cent) was presentas violarite ((Ni, Fe)3S4) whereas in the second it was present as pentlandite, ((Fe, Ni)9S8) (4·9 per cent Ni).A similar technique was utilized to convert nickel in nickeliferous laterites (1·6 per cent Ni) into a soluble chloride using town gas instead of oxygen as a carrier.With both techniques greater than 90 per cent extraction was achieved.

Jan 1, 1972

By C. R. Summers

In response to the Coal Mine Health and Safety Act of 1969, mandatory noise standards have been developed that specify time-noise limits of mine personnel exposure. Most affected by elevated noise levels is the pneumatic roof bolter operator, both in terms of levels near or in excess of 115 dbA and in terms of length of exposure. Therefore, the principal emphasis of this Bureau of Mines report is on pneumatic drill noise control. It is not the intent of this report to suggest any drill redesign; instead, methods are suggested to reduce the noise level by complementing existing machines. An integral muffler system and a separate muffler system were tested in an attempt to lower pneumatic drill noise levels. Pneumatic drills, when new, operate at about 115 dbA when drilling in sandstone. Using the drill muffler systems, it was possible to decrease the noise level of a 115-dbA stope drill to approximately 100 dbA.

Jan 1, 1974

By S Dunham

A cross-discipline approach combining geology, metallurgy and mine planning, geometallurgy is seen as the next logical advance in improving the design and operation of mining businesses. This rapidly evolving field is focused on realising the value that has often been lost in the chasms between the aforementioned technical silos. When successful, the geometallurgical approach promises the ability to tailor mining and mineral processing development and operational options more closely to the characteristics of the resource with resulting lower costs (both capital and operating), improved recoveries and fewer project failures.As with any technological (or managerial) change, there will be side effects from the success of the geometallurgical approach that will impact areas beyond obvious linkages between geology and processing. Some of these effects have the potential to be beneficial to the resource industry and society in general. Beyond the basic geometallurgical promise of closer alignment between processing design/strategy and the multivariate 3D spatial characteristics of the mineralisation, this paper discusses the broader implications and ramifications of the emergent geometallurgical approach: enhancing exploration and discovery; improving project development success; achieving sustainability in an industry working with non-renewable resources; in a world of increasingly hard won license to operate, improving the management of potentially harmful by-products and waste materials (with knock on effects for proactive management of closure issues); smarter approaches to energy management and thus optimisation of projects with respect to carbon footprint; and potential to re-value assets and thus realise a strategic advantage in the area of acquisitions, divestments, mergers and take overs. The authors strongly believe that companies that actively engage with the above issues (and ensure that technical efforts in the area of geometallurgy are not isolated from the larger value chain activities of the firm) will be able to exploit the opportunities that consequentially arise. These early adopters will gain first mover advantages. Firms taking the broad view of geometallurgy will have an opportunity to maximise stakeholder value and win greater success than their less insightful competitors.

Sep 5, 2011

By Jai-Woon Moon, Wonnyon Kim

Deep-sea hydrothermal vents (hereafter chimneys) are commonly found on the new crust forming along divergent plate boundaries. Related to the chimney cycle from birth to death, it is hard to define the growth stage of the chimney due to a brief life span of the venting hydrothermal plume. Here we try to categorize the mineral magnetic properties of the chimneys according to their venting fluid-temperatures. Hydrothermal sulfide deposits in the Southwest Pacific were explored in 2012 and chimneys were collected using remotely operated vehicle (ROV) and Grab with AV camera (GTV). In the present study, mineral magnetic properties of three Cu-rich chimneys were measured: a high-temperature chimney showing a venting fluid-temperature of about 200°C (ROV01); a lowtemperature chimney of about 80°C (GTV01); and an inactive chimney (ROV02). The chimneys were sliced to ~1 cm intervals from core to outer margin. Magnetic properties of ROV01 are dominated by pyrrhotite, except for the most outer part that experienced severe oxidation. Concentration and grain-size of pyrrhotite are relatively low and fine respectively. In the GTV01, pyrrhotite, dominant in the core, is gradually mixed with hematite toward the outer margin of the chimney due to secondary oxidation. Both the concentration and grain-size of the magnetic minerals are greater compared to the GTV01. High concentration and large grain-size of magnetic minerals characterize ROV02. Dominant magnetic phases are pyrrhotite, hematite, and goethite. In particular, the most outer margin shows the presence of magnetite produced possibly by magnetotactic bacterial activity. Such distinctive contrast in magnetic concentration, grain-size, and mineralogy among three different types of chimneys enables the life stage of the Cu-rich chimneys to be determined through a mineral magnetic study.

Sep 1, 2014

By Turker Hudaverdi, Yasar Agan

This study tries to predict blast-induced flyrock using intelligent modelling techniques. Flyrock is a site-specific phenomenon. Design variables and rock properties highly influence flyrock throw distance. Site investigations were conducted in a sandstone quarry. Fundamental operational parameters, blast dimensions, bench face condition, and rock mass structure were monitored. Stepwise regression technique was applied for variable selection. Burden–hole diameter ratio, in situ block size, and powder factor were determined as the most significant parameters. Considering output of stepwise regression, artificial neural network, ANFIS, and Gaussian process regression techniques were applied to predict flyrock throw. A comprehensive validation was performed using twelve different performance indices. Pre-determination of input parameters supported development of successful soft computing applications. Rock block size was found to be an appropriate input variable for flyrock modelling. In addition to classical performance indices, standardized and symmetric accuracy metrics were quite useful in model validation process. The intelligent models predict flyrock range with an error less than 6 m. The mean percentage errors are lower than 10%. ANFIS seems to be the best model for flyrock prediction. The calculated mean absolute error is 5.36 for ANFIS model.

Nov 12, 2023

By Wendy L. Naysmith

This paper deals with the various options considered and factors that influenced the final selection of the headframe, shaft layout and hoisting systems required at the Impala No 16 Shaft in order to hoist both the required 3 Mt of ore per annum, and transport men, material and equipment between the surface and the underground workings to a depth of 1640 m. The layout and construction method used for what is at present the world?s tallest concrete headframe is discussed together with the integrated hoist room foundations designed to suit multiple mechanical and electrical hoist supplier?s solutions. The mechanical components of the two tower mounted 6,5m 4 rope Koepe hoists and deflection sheaves and their layout is dealt with in detail. Various features of the bearing type, brake units and brake control system are also discussed. Installation of the mechanical and electrical hoist equipment in the headframe took place during the sinking phase of the project and placed severe restrictions on the use of the heavy lifting facilities. This required a well-managed and systematic approach to delivery of the hoist components and associated equipment, as well as close co-operation between all contractors on site.

Oct 1, 2010

By N. Ward

The Gualcamayo Mine is located in the Andes Mountains north of San Juan, Argentina (Figure 1). A property of Yamana Gold Inc, it declared commercial production in July 2009 and has a total mineral reserve and resource base of approximately 88,000 kg of gold. Crushing operations for the open-pit mine are located in a 13,500 m3 underground cavern with a ceiling height of 22 m. More than 3,600 m of tunnels are used to access the cavern and convey the ore. The Project as described in this paper relates to the design and construction of the Main Cavern, Conveyor System Exit Tunnel, the Mechanical System Access Tunnels, and two 4.20 m diameter shafts (Ore Pass #1 and Ore Pass #2) as shown in Figure 2. [ ] Preliminary engineering for the Project was performed by Hatch Chile. Rizzo Associates Argentina, S.A., a division of Paul C. Rizzo Associates, Inc (Rizzo) was contracted to provide geomechanical and geotechnical support for the construction of the access tunnel system and geomechanical design and construction supervision for the cavern and shafts.

Jan 1, 2011

By L. Nichols, H. Keele, K. Czajewski

"The oil sands industry in northern Alberta disposes of the by-products of bitumen extraction into tailings ponds. The mix of tailings sand and mature fines, with gypsum added as a flocculent, constitute a waste stream called consolidated tailings or composite tails (CT). The two main challenges of the tailings disposal process are a chronic shortage of economical containment and the potential mobility of CT deposits in the event of breaching by, for example, long-term erosion, which makes abandonment of tailings ponds more complicated. Thick deposits of CT do not consolidate in adequate time to provide reassurance for abandonment of the CT containment facilities and that is why the containment must be adequately robust or the properties of CT improved for long-term stability. This paper addresses potential solutions to these problems by applying the gravity drainage of CT and quasi-homogeneous construction for containment facilities.Gravity drainage is suggested as a mechanism to facilitate the consolidation of CT in critical areas of the ponds by inserting internal sand layers within the body of the deposit. Critical CT areas are defined as areas around the perimeter of containment. The advantages of this solution are longterm stability of the disposal area by creation of stiff deposits around its perimeter and facilitation of reclamation efforts on its surface.The present solution for containment of CT deposits is not favourable from a materials balance point of view. In general, sand has become a valuable resource as it both forms the primary component of the CT matrix and becomes the containment building material. If sand is required for CT, less is available for dyke construction. This puts additional pressure on the industry as a whole to maximize the use of overburden and interburden for construction of tailings containment structures. Typically, only 50 percent of dry mine waste (overburden + interburden) is incorporated into dyke construction. The remainder of dry waste is stored either in waste dumps or in tailings ponds, consuming valuable in-pond space originally allocated to CT material. Quasi-homogeneous dykes are proposed to contain CT deposits rather than traditional minimum cross-section dykes built of overburden and/or cell sand. The quasi-homogeneous dyke may change the unfavourable material balance and lessen the construction constraints that are presently imposed on the mine/waste disposal process."

Jan 1, 2008

By Dana T. Updyke

The objective of this project was to develop technical data and evaluate performance and utility of leaky feeder communications systems currently used in North American underground mines. The desired information was obtained principally through on-site surveys. Altogether, six of the seven mining companies known to be using leafy feeder communications were visited. This report covers the findings of these surveys. In addition, the report provides a brief background summary of mine communications, a technical discussion of leaky feeder systems, and conclusions and recommendations based on the results of the survey.

Jan 1, 1980

Mining steeply dipping coal seams is a difficult task in the mining industry. Prior to 1996, fully mechanized longwall mining methods along the seam strike direction were tried in China and other countries. Due to its larger coal reserve in steep seams, China made more but still limited progresses on mining in such seams than the other major coal-mining countries. In the last two decades, accelerated research efforts have been made to improve the mining technology in steeply dipping coal seams. Based on these works, a dynamic model of ?R-S-F? system under asymmetrical constrains in mining steep seam is established and the theory of strata control and hazard prevention begin to be formed. The key technologies for mining steep coal seams include: global and regional strata control methods in longwall face, methods for the longwall face machines to sustain static and dynamic loads, and flexible protection technology. These theory and technologies have been successfully applied to mining of steep coal seams of varying thickness and hardness, with hard and soft roof and floor, and with high potential of spontaneous combustion in China. In the recent years, the technology has been introduced to Russia, India, Uzbekistan and other countries where steep coal seams are mined.

Jan 1, 2012

By Linda Gaines

Use of vehicles with electric drive, which could reduce our oil dependence, will depend on lithium-ion batteries. But is there enough lithium? Will we need to import it from a new cartel? Are there other materials with supply constraints? We project the maximum demand for lithium and other materials if electric-drive vehicles expanded their market share rapidly, estimating material demand per vehicle for four battery chemistries. Total demand for the United States is based on market shares from an Argonne scenario that reflects high demand for electric-drive vehicles, and total demand for the rest of the world is based on a similar International Energy Agency scenario. Total material demand is then compared to estimates of production and reserves, and the quantity that could be recovered by recycling, to evaluate the adequacy of supply. We also identify producing countries to examine potential dependencies on unstable regions or future cartels.

Jan 1, 2010

By F. T. Wang, Y. Yuan, S. H. Tu, X. G. Zhang

Hydraulic support instability (HSI) is one of the most common causes of disasters in underground coal mining, posing a threat to the safety of mine workers and normal operation of the equipment. It is prone to occur in fully-mechanized mining faces with a large mining height (FMMLMH), especially when the dip angle of the coal seam is large. The key to controlling HSI is to deduce its mechanism and employ effective control techniques. This paper focuses on the analysis of HSI types, the key parameters and techniques to control HSI in FMMLMH, the establishment of a model of HSI in FMMLMH, and a multi-parameter sensitivity mechanical model of different HSI forms in the no. 7219 longwall face in Xutuan Coal Mine, Huaibei Mining Group, by using sensitivity analysis . The results show that HSI mainly presents in three forms: hydraulic support gliding (HSG), hydraulic support tilting (HST), and hydraulic support tail twisting (HSTT). The occurrence of the above three forms depends mainly on support anti-instability capability. In the no. 7219 longwall face, HSG and HST are the main two forms of HSI. The dip angle of the working face and the friction coefficient between floor and hydraulic support are the sensitive parameters for HSG, while HST is strongly dependent on the dip angle of the working face and the friction coefficient between roof and hydraulic support. By the applications of measures such as the oblique layout of the working face, cutting the floor into a step pattern, moving the support under pressure, and raising the setting load, the support stability was controlled effectively.

Jan 1, 2015