Search Documents

By Ken Dyck, Chuck Edwards

"Cameco's McArthur River is the world's largest high grade uranium mine. Production started in late 1999. Cameco carried out the engineering design and construction management for the McArthur River project, including all aspects of mining, ore handling and ore transportation. The ore composition was expected to vary dramatically (0 to 30% U3O8; 0 to 25% clay; etc). To cope with the composition swings, sizing screens were selected to provide classification in the grinding circuit. The grinding circuit started up close to the design to provide minus 500 micron slurry. The 50% solids (wt) ground ore slurry proved to be difficult to transport to and process at the Key Lake Mill. Slurry containing high concentrations of high density pitchblende (about spgr 8.0) and low concentration of stabilizing clays, would settle in containers. Ore transport efficiency to Key Lake was found to be unacceptable.A test classification cyclone was installed in the grinding circuit at McArthur River early in 2002. The cyclone operating parameters were not typical, but the cyclone was made to work very successfully. Transportation efficiency to Key Lake increased due to more stable slurry. Preferentially ground (fine) pitchblende particles were easier to leach at Key Lake. The radiation exposure for operators and maintenance personnel to handle the more stable slurry was also reduced.The classification sizing screens were removed from the McArthur River grinding circuit and replaced by permanent classification cyclones late in 2002.INTRODUCTIONThe McArthur River mine and Key Lake mill operations are located in northern Saskatchewan, approximately 650 and 720 kilometres from Saskatoon, respectively. Figure 1 is a location map. McArthur River is the world's largest, high-grade uranium mine, with a production capacity of 18.7 million pounds U3O8 annually. (Rosner and Edwards 1998, Dyck 2000, Jamrozek 2000, Rodgers 2001) Proven and probable reserves are more than 473 million pounds U3O8. McArthur River ore, grading on average 21% U3O8, is milled at Cameco's Key Lake operation, 80 kilometres southwest by road. McArthur River production began in December 1999."

Jan 1, 2004

By John Trefny

Although mining is currently one of the smallest academic units on the Colorado School of Mines(CSM) campus, it is alive and well, with nearly 100 undergraduate and graduate students. For many years, Mines has had undergraduate and graduate programs in hard-rock mining. The school has recently transferred its physical mineral processing activities to the Mining Department. The program has also expanded to include tunneling, underground construction and industrial minerals. There are current discussions about increased research activities on cement and other construction materials. The Mining Department also teaches its share of what is called the “distributed core” courses with curricular requirements common to related programs, as well as mining safety and health, in conjunction with our continuing education department.

Jan 1, 2002

The Physiographical Features of the Region The Middleback; Range proper, from the Iron Duke in the south to the Iron Prince in the north, extends in a meridional direction for 21 miles, but may well be taken to embrace also the Iron Knob and Iron Monarch prominences so that the total length of the Range is 37 miles.Although no great altitudes are reached, the slopes of the high country are steep and the Range stands out prominently above the peneplaned surface of upper Eyre Peninsula. The Range is built up of sub-parallel ridges at some places, and its continuity is interrupted by transverse breaks or gaps resulting from normal stream erosion and corrosion during earlier periods when precipitation was heavier and streams were more active. Traces of high-level gravels remain on the flanks of Kimba Gap. A former mature stream on the western side of the Range has had its lower reaches blocked by sand and the old stream channel has been converted into an eiongated basin of internal drainage. The sand dunes in this area appear to be practically stationary at present, being fixed by mallee vegetation. Their trend is west-northwest.The relief of the Range is regarded as having been determined primarily by meridional strike faulting and selective silification of some of the beds. Dip faulting on the Iron Duchess leases has produced subsidiary features only.The Rocks of the Region: In order that some of the points made in the discussion of the genesis of the ore bodies may be appreciated it is necessary to consider the stratigraphical succession and the igneous types represented. This classification may be...

Jan 1, 1949

By Kurt Oakes, Paul Worsey, Braden Lusk, Tony Brasier, Jerry Chambers, Scott Crabtree, Randy Wheeler

Destructive wave interference has been studied in theory for many years. In application however, limited information can be found. Recently, circumstances have enabled a multidisciplinary team to utilize electronic detonators and seismograph analysis to create destructive wave interference in an underground production blasting application. Springfield Underground, located in Springfield, MO, in conjunction with Orica, ETI, White Industrial Seismology, and the University of Missouri – Rolla has shown the ability to use destructive wave interference in underground blasting to reduce ground vibrations directly above.

Jan 1, 2006

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005

On the basis of field observation, four principal styles of hydraulic breccia are recognised, and their characteristic features noted. In practice, hybrid styles are most commonly encountered. Numerous examples will be illustrated during the oral presentation, and the potential for definition of a formative environment is emphasised. In one example presented, it is suggested that more than 50 episodes of hydraulic fracturing can be recognised. In all cases at least sane useful conclusions can be drawn in the context of modeling for drill targets.

Jan 1, 1987

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By Guowen Dong, Qiyong Li, Qiang Li, Tiejun Chen, Zhihong Wu, Junying Wan

In order to search for a more economical and effective roasting additive for extracting vanadium from stone coal and solve the question of the disposal of PVC waste, PVC waste was proposed as a novel roasting additive to enhance extraction of vanadium from stone coal and realize the comprehensive utilization of resources. By adding this roasting additive, the leaching rate of vanadium reached 94.5% under the conditions that the PVC waste addition was 10 wt%, the roasting temperature was 800 °C, the roasting time was 1 h, the sulfuric acid concentration was 15 vol%, the liquid-to-solid ratio was 1.5 cm3 /g, the leaching temperature was 95 °C, and leaching time was 4 h, which increased by 8.4% compared with that of blank roasting. The thermodynamics calculation showed that the decomposition reaction of mica was performed easier with the participation of HCl produced by pyrolysis of PVC. Meanwhile, The SEM-EDS and aperture test analyses demonstrated that more cracks and voids appeared in the roasted sample by roasting with PVC waste, which could facilitate the release and extraction of vanadium. Additionally, the TG-DSC analyses indicated that PVC could provide large amounts of heat for the roasting process to promote the decarbonization and roasting efficiency of stone coal because of its high calorific value.

By N. Sahay

Open fire in coal mines is one of the most serious threats to miners, as well as to the mine. Open fire can often be effectively dealt with by prompt local action, otherwise it very quickly becomes uncontrollable. In one incident, none of the available open fire control technologies, viz., water deluge and sprinkler systems, high-expansion foam, high-pressure high-stability nitrogen foam, water misting, and ventilation and pressure control techniques, were effective for saving the mine without sealing from surface, since the fuel-rich environment prohibited underground access due to the methane explosion hazard. The authors have developed a methodology for dealing with advancedstage open fires underground by the application of a modified ventilation control technique. It is based primarily on a better understanding of the behaviour of open fires, proper diagnosis of the problem, application of judicious ventilation control techniques, and selection of suitable fire indices for assessing the status of an open fire. This methodology was used to successfully control an open fire in Surakachhar 3 and 4 incline mine Surakachhar, central India. The fire area was sealed underground and production subsequently resumed in record time. The paper discusses the behaviour of open fires, particulars of the mine, diagnosis of the problem, experimentation methods, and the results obtained.

Jan 1, 2014

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Mahmut Altiner

This study aimed to produce magnesium oxide (MgO) particles with different properties from dolomite ore using an experimental procedure comprising four stages: sample preparation (S1), HCl leaching (S2), precipitation (S3), and calcination (S4). Three different base sources (NaOH, KOH, and NH4OH) were used as precipitant in the third stage to obtain magnesium hydroxide [Mg(OH)2] from a leachate solution, which was obtained in the second stage. Next, Mg(OH)2 particles generated by different alkali sources were calcined at various temperatures from 600–1000 °C for different durations (1–5 h). The effect of these base types on the properties of each product was investigated by X-ray diffraction (XRD), scanning electron microscopy (SEM), Brunauer–Emmett–Teller (BET), atomic force microscopy (AFM), and wet chemical analyses. The experimental results indicated that each product was identified as periclase (MgO) mineral, which was produced with a specific surface area (SSA) of 4.49–44.54 m2 /g depending on the production conditions. The surface roughness of the MgO particles increased with increasing calcination temperature. SEM analyses showed that MgO particles produced at a temperature of 600 or 800 °C were amorphous, indicating that the process was not influenced by the base type, but MgO crystals were smooth when the calcination temperature was 1000 °C. Finally, it was determined from all experimental findings that MgO particles produced via the addition of NaOH have superior properties (such as higher SSA and lower surface roughness) compared with MgO particles produced with KOH or NH4OH as the alkali source. These properties led to great improvement of its usability in industry.

By Célia Aparecida Lino dos Santos

Os métodos convencionais e os mais recentes de proteção contra a corrosão (revestimentos metálicos aplicados por eletrodeposição, deposição química (electroless), deposição química em fase vapor, deposição física de vapor e aplicação de tintas) empregados paras as ligas de aço-carbono também são empregados para as ligas à base de TR-Fe-B. Essa proteção torna-se necessária, uma vez que essas ligas possuem microestrutura muito mais complexa que as dos aços-carbono e apresentam em sua composição metais de terras raras os quais são intrinsicamente susceptíveis à corrosão. Os revestimentos utilizados são, no geral, constituídos de metais mais nobres do que as ligas, sendo por isso de extrema importância que sejam mantidos íntegros durante o manuseio individual dos ímãs e durante a sua montagem, ou, o posicionamento nos diversos dispositivos em que eles são empregados atualmente. O rompimento do revestimento implicará a diminuição da vida útil dos dispositivos.

Oct 30, 2017

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By Congling Shi, Marek Borowski, Yue Wang, Jianwei Cheng, Xixi Zhang, Xuan Xu

As the first barrier to prevent accidents caused by explosions in underground coal mines, the integrity and stability of mine seals have great effects on mine workers’ lives and underground production safety. In this paper, the mechanical responding performance of typical mine seals under the impact load are studied by using numerical simulation method. By such simulation studies, the safety of different seals subjected to the explosion load is evaluated. Seals’stability are also investigated under effects caused by various influence factors including thickness of mine seal, cutting depth into surrounding rocks, rock type, and the roof-tofloor convergence under given the explosion load. The research results can provide theoretical basis and reasonable improvements for mine seal’s construction practices for improving its anti-explosion performance.

By Paulo von Krüger

Nas condições adversas do mercado atual, aliadas à exacerbada competição é uma questão de sobrevivência a otimização de resultados. Para tal é imprescindível que os principais insumos, particularmente os mais gravosos sejam criteriosamente selecionados. Os eletrodos de grafite estão entre os itens principais na operação dos fornos elétricos a arco, tanto do ponto de vista técnico, quanto econômico e a escolha correta deste insumo deve contemplar aqueles dois enfoques. Esta escolha se faz dentre as diversas classes, disponibilizadas no mercado: RP, HP, SHP, UHP. O que se pretende no presente trabalho é sugerir uma metodologia que, contemplando o elenco de parâmetros influentes, permita fazer a escolha correta do eletrodo, dentro daquelas classes, tanto sob o enfoque técnico, quanto econômico.

Aug 17, 2017

By I M. Platten, C J. S Sangster, Y Xie

The Cononish gold-silver deposit is a steep, relatively narrow quartz-vein system, with a current total mineral resource of 154 000 oz Au and 589 000 oz Ag. The northeast-southwest trending system was emplaced into late Proterozoic metasediments, and postdates metamorphism and associated Caledonian Orogenic foliations. Assay and mineralogical data show that gold and silver is spatially associated with sulfides in quartz. The main sulfide is pyrite, but galena, chalcopyrite and sphalerite occur in small amounts. Gold occurs as electrum, with minor native gold, and silver occurs additionally as tellurides and native metal. The gold/electrum is fine-grained, generally less than 100 microns in size. The main ore shoots plunge 45¦ south-west, have a 40 m to 80 m intersection with the existing underground development and extend between 40 m and 260 m down plunge. Small-scale sulfide-bearing domains within the vein carry the highest gold grades. They collectively define the ore shoots, where one or two, and rarely three, of the domains are present at an individual site in the vein. Discontinuity of individual domains, variation in domain thickness and internal heterogeneity results in short scale variation in grade across the structure. Geological mapping along a 1.2 km exploration adit has provided critical æconditioningÆ data to support resource evaluation based on development and relatively wide spaced drilling. In addition, it has provided an indication of potential challenges that could be encountered during production.

Jan 1, 2009

By W. S. Steinberg

In 1963, the full-scale engineering study for the development of an iron, steel, and vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steelworks that produced steel and vanadium-bearing slag from a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for prereduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to open slag bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of the higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By Raíra Morais Alcântara Nunes

No laboratório de fundição da Universidade Federal do Ceará, foi desenvolvido novas técnicas de fundição de precisão visando reduzir os custos utilizando materiais reciclados, como sucatas e cinzas residuais de termoelétrica. Ademais, ocorreu a preparação das peças modelo, utilização de silicone para a produção de moldes, preparação das peças em cera e canais de vazamento, fabricação da casca cerâmica refratária, vazamento da liga metálica (ZAMAC), obtenção da peça rústica e processo de usinagem. Desse modo, concluímos nosso projeto dando utilidade para um material poluente e reciclando sucata de zinco e, por consequência, baixando os custos desse processo e podendo haver, também, a geração de emprego para comunidades carentes.

Oct 30, 2017

By Masanobu Masukawa, Toshio Shiota

The shaft-type ferromanganese smelting furnace (SF) at Mizushima Ferroalloy Co., Ltd. has been in operation since startup in 1985 and is continuing to perform smoothly. Production has been increased from the original design capacity of 270t/d to 350t/d by various operational improvements. As a productivity index of the shaft-type furnace, production of 350t/d is equivalent to productivity of 0.9t/m3/d (daily production/cubic capacity of furnace). Recently, various operational improvements were implemented to achieve productivity of 1.0t/m3/d or higher, including oxygen enrichment operation, increased tapping frequency, maintenance of the throat profile, and operation with small lump coke. The target productivity of 1.0 t/m3/d was achieved in January 2005. This report describes the improvements introduced as part of this high productivity technology.

Jan 1, 2007

By Cynara Christ Klippel

Devido às exigências de teores de fosforo cada vez menores no aço, o processo de desfosforação tem ganhado destaque nas indústrias. Para aproveitamento das melhores condições termodinâmicas a etapa mais eficiente para o processo de desfosforação ocorre no ferro-gusa. Esse trabalho utilizou quatro misturas iniciais de composição definida com base na literatura, juntamente com o ferro-gusa para ser simulado o processo de desfosforação. A simulação foi feita através do software de cálculos termodinâmicos FactSage e através dos resultados obtidos do programa foram feitos cálculos para avalição da eficiência do processo. Além disso, também foram feitos cálculos baseados na literatura para comparação de resultados e estudo mais aprofundado dos resultados. Os resultados obtidos comprovaram a teoria inicial de que menores temperaturas favorecem o processo.

Aug 17, 2017