Search Documents

By M V. Van Bers, A L. McAnuff, A Curic

During the Summer of 1997, rock excavation was carried out for construction of the Centre Block Underground Services building (CBUS) abutting the most historically significant structural complex in Canada, the Parliament Buildings in Ottawa. Controlled blasting was required for the removal of 25,000 cubic metres of limestone bedrock within the ten week time window of Parliamentary recess. A test blast program carried out in 1996 had established that close blasting was viable even within the very restrictive limits considered necessary to preserve the structural and cosmetic integrity of these historic structures. In total 300 blasting operations were required to complete the excavation, including the 20 test blasts conducted in 1996. Based on attenuation characteristics established for the site during the trial blast phase, the blasting contractor proposed excavating the CBUS site in three zones. Each zone contained differing drill patterns, depths and explosive loads. Vibration intensities, air concussion levels and displacements across representative existing cracks were measured and recorded at numerous observation points within and around the Centre Block and the Library of Parliament, as well as on the grounds of the Parliamentary Precinct. The blasting portion of the excavation was completed within budget in less than eight weeks, well within the tune window available. Comparison of very extensive pre and post-blast condition surveys revealed no damage to the existing structures on Parliament Hill as a result of these operations.

Jan 1, 1999

By D. M. Dunbar, H. C. SCHLILTZ

HE Chile Exploration Co.'s mine and reduction plant are at Chuquicamata, Chile, on the eastern edge of the Atacama Desert, 163 miles northeast of Antofagasta, 80 miles from the Pacific Ocean, and 70 miles from the Bolivian border and at an altitude of 10,000 ft. Guggenheim Brothers started prospecting in -4pri1, 1912, and purchased the main property, in October of that year; the property is now controlled by the Anaconda Copper Mining Co., which acquired it in January, 1923. The orebody strikes north 10" east, and has a dip of about 64" west. The length, as far as developed, is approximately 1% miles; the width averages sightless than mile.

Jan 1, 1925

By Joe Atalla, Jesse Desrochers, Rodrigo Hayashida, Joseph Mukendi Kabuya

The Mont-Wright mine stands as a prominent open-pit operation in Canada, renowned for its vast iron-ore reserves. However, the efficacy of its blasting operations, crucial for efficient production, has encountered challenges due to the diverse lithological compositions across multiple pits. This study presents a comprehensive approach to optimize blasting practices at Mont-Wright mine, tailored to the specific lithological characteristics of each rock domain. Through systematic analysis and experimentation, blasting guidelines were meticulously developed, aiming to enhance grindability and equipment productivity. The implementation of these guidelines promises significant improvements in operational efficiency and resource utilization, positioning Mont-Wright mine at the forefront of sustainable iron-ore extraction.

Jan 21, 2025

By B. Corrêa, M. Cavalcante

A large open pit iron ore mine in Brazil, which has a heterogeneous lithology, faces a challenge in defining drill and blast patterns to achieve the expected results. The mine needed to obtain an automated representation of the fragmentation curves and correlate them to the respective blasts, lithologies and quality parameters, seeking the continuous optimization of the fragmentation process and its benefits to the subsequent comminution processes. Trials were carried out for 5 months to demonstrate the functionality of an autonomous fragmentation monitoring system that analyzes the granulometric curve of the material throughout the muckpile and makes the results available online and in real time. The system, which contains a binocular camera, a processing unit and an antenna, was installed in a shovel, to evaluate the following KPI's: monitoring failures, monitoring capacity, physical availability and reportability of oversized boulders. The system analyzed 33,060 samples, with an average capacity of 285 photos every 24 hours, 127 during the day and 158 at night, all measured, analyzed, stored, and made available on its online platform, reporting 223 alerts of P80 above 400mm (15.7 in) and 38 particle sizes above 900mm (35.4 in). The inactive and operational hours of the monitoring system corresponded, respectively, to the idle and worked hours of the shovel, according to dispatch data. There were no camera or processor failures, and rain, dust or poor internet conditions did not impact sampling and fragmentation analysis, indicating 100% physical availability of the system. The autonomous monitoring analyzed 139 times more samples compared to the currently used manual method. In addition to increasing sampling representativeness and automating the process, it increases the safety, quality, and productivity of granulometric analysis, eliminating the exposure of people in the mine and human bias in the analyses. Additional analyses were performed by correlating digitally centralized drill and blast data, data from autonomous drills and fragmentation results. Automated obtention of granulometric curves favors quick decision-making and optimization of blasts to achieve better results in productivity and cost reduction in the plant and mine operation. The autonomous fragmentation monitoring system met the need presented by the mine, proving to be a key tool in continuous improvement projects, including Mine to Plant.

Jan 1, 2024

By R. Franfield

This paper describes a situation that many drilling and blasting contractors have found themselves in – a client?s fear of the use of explosives. In the summer of 2007 Blasting Services Ltd was asked to undertake some drilling and blasting work in an abandoned quarry that was being restored for a housing development. Previous quarrying operations had left a series of overhangs that were considered unsafe and required removing. The site contractor considered that the best and safest way to carry out this work was by drilling and blasting. Blasting Services Ltd, with the technical assistance of Exchem Explosives, designed a drilling and blasting regime to accomplish this work with a series of trim blasts. The design took into account the close proximity of a structure in very poor condition and the imposed vibration limit of 6.0 mm/s (0.24 i.p.s.). The faces were profiled, holes drilled and explosives ordered. A few days before the first blast was due to be carried out the client decided that the poor condition of the nearby structure meant that the use of explosives could not be permitted. This decision was made despite the blast design indicating that the vibration level would be well below the 6.0 mm/s (0.24 i.p.s.) limit.

Jan 1, 2009

By Chris G. Dobson

Introduction The Britannia mine is at Britannia Beach, on Howe sound, approximately thirty miles from Vancouver. The first claims were staked in 1898, and a local company was formed at that time to develop them. In 1904, Mr. Grant B. Schley became actively interested in the property and in the following year the Britannia Mining and Smelting Company, Limited, was incorporated to operate it. This Company was taken over a few years later by the Howe Sound Company, Limited. The mine comprises five more or less separate ore-bodies, which have produced approximately 20,000,000 tons of ore to date. The East Bluff ore-body, with which the present paper deals, is well suited to large-scale mining by means of carefully placed powder blasts. It covers approximately an acre and lies in the slate footwall, in a bay produced by a fault. The hanging-wall side, on the west, forms the face of the Bluff glory-hole, which extends to the 1,200 level. A portion of this ore was available for breaking into this old glory-hole, below which four bulldoze chambers could quickly be built. Mining of this block is complicated by a very soft footwall, which 'runs' badly when broken. In stoping, care is taken to guard against the hazard of dilution by deliberately leaving a small portion of ore on the footwall. Some of this will undoubtedly be lost, but it is hoped to recover a fair amount of it after the major drawing is completed. The deposit occurs in a greenstone which has been highly silicified following brecciation. The chief minerals are chalcopyrite, sphalerite, and pyrite. Concentrates of copper, zinc, and pyrite are made at the mill. The average grade of ore runs 0.7 per cent copper, 1.5 per cent zinc, and 0.03 oz. gold per ton. The rock, which is practically a chert, is extremely hard, but shatters well. Both in stoping and drifting, holes must be closely spaced and powder used generously. Development When development work started in the East Bluff, there were no raises and only one drift on each level in this section of the mine. After blocking out the ore by thorough diamond drilling, a production of two thousand tons per day was set as a goal. To obtain this tonnage from so small an area required a great deal of carefully planned and well timed development work.

Jan 1, 1935

By Edward J. Karkoska

The film you see is a slow motion view of a typical half million ton taconite blast at one of Erie's mines. This blast is made up of 220 drill holes and a total of 325 thousand pounds of blasting agent. The second view of the same shot is taken by a remote control hi speed camera located 1500' directly in front of the blast. Shortly you will see some violent camera movement as the air blast shock wave strikes the camera location. As the blasting sequence progresses the rock fly becomes evident, and if you will look closely amidst the clouds of smoke, rock fragments weighing up to 1/2 ton begin to cascade into view. These missles are the chief concern of blast security. The next camera shot at 4000 frames/second vividly describes the primacord firing lines detonating the blast. Travelling at 22,000 ft./sec., this white snake of fire travels to each hole, detonating the blasting agent. Before we get into the matter of blast security, let me locate our operation for those of you not acquainted with Minnesota's iron ranges and tell you something about our company.

Jan 1, 1969

By C. J. Gilbert

The mining method at the Cannon Mine uses heading and bench stopes, which are subsequently backfilled with cemented high-strength fill prior to pillar removal. The dimensions of the pillars, 24 feet wide by G5 to 95 feet high, re-quire careful blasting in order to not damage the rock, compromising pillar strength and complicating later removal. Additionally, the proximity of dwellings makes vibration control a must for good-neighbor relations. A blast monitoring study was conducted in order to optimize bench blasting practices to maximize fragmentation, reduce costs, minimize well damage, and minimize ground vibration.

Jan 1, 1989

By L. H. Bergmann

THE blasting practices described are fairly representative of those employed in the coal mines of Eastern Canada. As such, they may be of interest to Western Canadian coal mine operators. The treatment of the subject is general, no attempt being made to discuss blasting operations at any particular coal mine in detail. All the mines dealt with are mining bituminous coal and are classified under the Coal Mines Regulation Act of the Province of Nova Scotia as 'closed light' mines. As such, they are required to use only 'permitted' explosives and to apply them in a 'permitted' manner, except where authority is given by the Mines Department to do otherwise.

Jan 1, 1945

By Victor C. Bryan

"One of the more challenging issues facing operators of U.S. mines and quarries is blasting in an environmentally acceptable way. It is quite important that industry management understand and apply guidance, discipline, and control in the exercise of blasting operations. This presentation is a discussion of problems related to that environment away from the blasthole that may or may not be adversely affected by blasting and the steps management may consider in resolving resultant problems. In any case, one of the main concerns that will continuously be brought up is thatmanagement procedures inherent to good blasting is a uxporate responsibility of the mine or quarry business entity; and can not be delegated to the explosive manufacturer or supplier. This management attitude, based on education, training, and the comprehension that the process of production begins with drilling and blasting and consumes a significant amount of overall production costs."

Jan 1, 1995

By Frank Sames

Most Blasting Programs are developed focussing on the environmental impact with respect to blast vibration and airblast. Compliance with existing regulations or policies limiting the immissions are generally achieved through constrains in the blast design, or monitoring programs. Efficient monitoring programs combine compliance monitoring and blast assessment. Signals, which are obtained in the area of direct influence of the seismic source, can contain valuable information about the blast design parameters. Techniques to analyze blast vibration signals have advanced and can assist in understanding the contribution of individual blast parameters to blast vibration and airblast. Advanced signal analysis encompasses magnitude analysis, Fast Fourier Transforms (FFT) and frequency scans in the frequency domain, as well as filtering in the time domain. Through examples, the advanced signal analysis techniques and their limitations are described and discussed, showing the impact of blast timing, timing accuracy, charge configuration and the geology dependent transmission behavior. Optimization criteria and pragmatic monitoring programs can be developed on the basis of the most influential blast parameters. In addition, however, safety and the cost efficiency of the blasting program are essential to the success of an operation. That is where advanced signal analysis techniques can interface with blast planning, computer assisted modeling and information systems. A valuable process can be developed to ensure compliance with existing regulations and efficient risk management for mining operations, while tracking cost and supporting operational decisions. A conceptual blasting information system is presented.

Jan 1, 2000

By J Jackson, E Sellers

Blasting related indices were developed to quantify variation in rock strength and structure for each stope, and for each lift of each stope, as part of a Mine to Mill study at an underground open stope mine. The indices were derived from combinations of data from underground diamond drilling because the simplifying assumptions contained in the block model prevented sufficient differentiation in rock mass characteristics to enable adjustments to the blast design.Application of combinations of blasting related indices enabled the identification of stopes with a high potential for inconsistent and oversize fragmentation, underbreak and overbreak. The indices also fragmentation outcomes to deliver increased material flow within stopes, better digability and predict indicative mill throughput. The stopes with issuesCalibration of the results enabled adjustments to the blast design based on the rock mass conditions and accordingly improved the blast outcomes. This enabled improved productivity by reducing underbreak and overbreak, having a more appropriate fragmentation, which reduces unplanned rock handling and improves bogging. The reduction in recovery drilling creates huge opportunities to improve output by reducing production delays and decreasing the overall cost per tonne. By understanding the explosive performance and blast energy distribution in relation to rock mass blastability poor, performing designs in blind upholes and convex stopes were identified.The conclusion of the work is that value improvement, regarding increased revenue and reduced costs, can be achieved across the whole underground Mine to Mill process chain by developing stope based indices from the existing geological information to correctly tailor the blast design to the rock within, and surrounding, the stope.CITATION:Jackson, J and Sellers, E, 2017. Blasting related indices as the key to underground blasting improvements in a challenging rock mass, in Proceedings 13th AusIMM Underground Operators’ Conference 2017, pp 23–32 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Oct 16, 2017

By R. F. Favreau, G. E. Larocque

The objective of the study is development of an analytic process based on rock and explosive properties which allows the prediction of the stress distributions and fracture zone around explosive charges. A computer program has been written for this purpose, using a finite difference approximation to the momentum equation, to describe the motion of the surrounding rock by step-wise integration. Its application provides ground motion data such as stress components, displacement and particle velocity as a function of position and time with respect to a spherical charge. The effect of tensile and shear failure on these ground motion parameters can be included. The analytic procedure contained within this program has been used to predict peak stress as a function of distance in rock for rock-explosive combinations for which field data exists to determine peak stress levels directly. Two methods have been used for the spherical charge which in the analysis replaces the actual cylindrical charges: instantaneous application of peak pressure to a charge having a radius equivalent in contained volume to a charge having a length to diameter ratio of 1, and gradual pressure build up to peak pressure with a charge radius equivalent in contained volume to the total charge used in the field test. The agreement with field data would appear best with the latter treatment. The peak stresses obtained are in closer agreement with field measured peak-stress and a better approximation to field stress wave duration exists in the case of gradual pressure build up. One of the assumptions made in the analysis is that, in the case of cylindrical charges, the explosion pressure rather than the detonation pressure of an explosive establishes the peak stresses in the

Jan 1, 1971

By B. J. Kochanowsky

To improve blasting methods it is necessary to know how the explosive force acts and how rock resists this force. Because of the tremendous power developed within milliseconds and the great number of other factors directly affecting the technical and economic results, an analysis of the fundamentals of blasting theory is difficult. But since the rules used for layout design and for calculations of size of explosive charges are based on theoretical assumptions, complete knowledge of blasting theory has great practical importance in mining. Analysis of Blasting Theory: It is interesting to note the opinion of blasting experts with respect to contemporary blasting theories. F. Stussi,' Professor of the University of Zurich, stated: "We do not have enough experience yet to change our army engineering regulations in blasting and base it on new fundamentals. It is our duty to collect more practical data and to do more research in blasting to close this gap." K. H. Fraenkel,' editor of the Manual on Rock Blasting published in 1953 in Sweden and written by well-known Swedish, German, Swiss, and French blasting and explosive experts, said: "To the best of our knowledge no suitable formulas for civil blasting work are to be found in the American, French or German literature."

Sep 1, 1955

Recent analysis of backfilling material has shown that a finer size distribution is preferable for stope filling. In order to increase crusher throughput and pit productivity, a reassessment of the quarrying operation was conducted. Part of that reassessment was a review of blasting practice. Six means of reducing the average muckpile fragment size were examined. Different blast initiation and charging options were compared, and patterns using smaller hole sizes were designed, analysed with the JKMRC 3x3o software, then drilled and fired. The ground vibration and face movement was recorded and compared. To determine whether the Kuz-Ram model could be used in an economic analysis of the quarry operation, the fragmentation distribution of the small diameter hole blasts was determined. Photographs of the muckpiles were taken and digitised. However subsequent analysis indicated that a satisfactorily large photo sample was only obtained from the smallest diameter hole blast. The Kuz-Ram fragmentation model prediction was found to be within the confidence limits of those results. An engineering and cost comparison between the blasts was made.

Jan 1, 1995

By Thomas E. Lobb, Harry C. Verakis

Significant progress has been made in the reduction of serious injuries and fatalities resulting from mine blasting operations. Despite the progress, injuries and fatalities continue to occur. A leading cause of injuries and fatalities from blasting continues to be inadequate blast area security. Even though significant improvements in technology have been made, insuring adequate blast area security remains a challenge and requires constant vigilance. The advances in technology have created safer blasting products and have improved productivity and economics by enabling large, more efficient and effective blasts. However, as blasts grow larger in size, the complexity of adequately securing the blast area increases even more. Periodically the basic fundamentals involved in blasting safety should be reviewed, particularly for securing a blast site regardless of the size of the planned blast. Factors such as flyrock and toxic fumes must be taken into account to insure the safety of persons and property from the results of a blast. This paper examines the factors related to injuries due to inadequate blasting shelters and blast area security, and identifies mitigation techniques. The key concepts are: (a) accurate determination of the bounds of the blast area, (b) clearing employees from the blast area, (c) effective access control, (d) use of adequate blasting shelters, (e) efficient communications, and (f) training. Fundamentals are reviewed with an emphasis on analyzing task elements and identifying root causes for selected blasting accidents. Mitigating techniques are presented along with discussions and examples.

By Kenneth Eltschlager, Jim Ratcliff, Michael Mann, Edward Sheehan

The Appalachian Blaster Certification Delegation initiated a study to compare the consistency of measurements from blasting seismographs. Six blasts were monitored at surface coal mines in West Virginia, Maryland, and Ohio. A total of seven different makes were deployed during the tests, with as many as seven models from five different manufacturers compared during any one blast. Great care was taken to bury the geophones in identical fashion. The variations in seismograph readings were compared to the International Society of Explosives Engineers’ Performance Specifications for Blasting Seismographs. Between 4 and 125 Hertz, the ground vibration amplitudes should be within ±5% and airblast amplitudes should be ±1 decibel. For each of the three mutually perpendicular ground vibration channels and the acoustic channel, the median value of all the units was used as a baseline for comparison. The six blasts monitored had median peak particle velocities ranging from 0.42 to 3.47 inches per second (in/s) (10.7 – 88.1 mm/s) and median airblasts ranging from 124 to 135 decibels (dB). There were 46 seismograph recordings for the six blasts. Eighteen (39%) of the 46 maximum peak particle velocities varied more than ±5% from the median. A total of 138 (3 × 46) component particle velocities were recorded, with 50 (36%) of the readings varying more than ±5% from the median. For airblast comparison, 43 recordings were obtained, with seven (16%) varying more than ±1 dB of the median. Variances may be attributable to blasting seismograph differences, variations in field deployment, and relative locations of the geophones. Full waveform seismic and acoustic overlays for individual blasts showed encouraging conformity with some slight anomalies

Jan 1, 2015

"In this work a blasting seismograph was tested on a vibration shaker controlled by a single-point laser Doppler vibrometer (LDV). A total of 43 tests were made to measure the transfer properties(transmissibility and phase shift) of the basic elements of the full monitoring chain and investigate theperformance of the full system. The main elements of the seismograph are described by second ordertransfer functions with typical parameters calibrated through nonlinear fit of the measured responses. The resulting transfer function is used to compare the behavior of the tested seismograph with fourtheoretical seismographs representative of those used in blasting. Fifteen theoretical inputs are runthrough the transfer function of each seismograph to assess their steady-response. The error (expressed as gain) in the peak velocity has been assessed. It varies from -1.5 to 2.3 dB (equivalent to atransmissibility of 0.84 to 1.3, respectively) depending on the seismograph and frequencies of the input.The largest errors occurred for input signals with frequencies in the low (<32 Hz) or high ranges (>125Hz), where the mechanical, electronics and digital parts of the seismograph modify the signals. Seismographs with the nominal transfer function described by DIN 45669:1:2010 are ranked with the smallest errors. Monitoring devices with transmissibility around one in a narrow bandwidth, in line with ISEE suggested criteria for amplitude response, involve large phase shifts at low and high frequencies, resulting in a worst performance."

Jan 1, 2017

By H. B. Farnam

"THE IRON ORE Company of Canada has been using do-it-yourself type explosives for three years. During the last 12 months we have used over 10 million pounds of ammonium nitrate-fuel oil explosives and either purchased or formulated one million pounds of slurried explosives.W e have been moving approximately one million cubic yards of stripping and ore per month and we expect our production rate to in-crease. Eighty per cent of our strip-ping and ore is soft enough to be blasted successfully with ammonium nitrate-fuel oil mixtures. Twenty per cent of our material is extremely hard and requires an explosive having greater strength than an AN-fuel oil mixture.W e had been using canned am-monium nitrate base explosives and TNT pellets to give maximum bottom loading density to fracture hard rock. As AN -fuel oil became widely used, it was apparent that other types of explosives could be formulated to fit our blasting requirements. Dr. M. A. Cook of the University of Utah was consulted regarding new explosives and together we developed the blasting slurries.Figure 1 shows a general view of one of our hard rock pits. The foot wall is on the right-hand side and this material is called iron forma-Figure 1.-General view of hard rock pitstion by our Company but is called 'Taconite by the operators on the Mesabi Range. This material runs 35 to 45 per cent iron and many pieces are hard enough to scratch glass. The formation is tilted at an angle of 55 degrees as can be seen in Figure 3.The bedding planes of this rock are about 24 to 36 inches apart and if the material is not well broken or fragmented, large chunks or slabs must be handled by the shovels which reduces shovel capacity and efficiency and increases maintenance costs."

Jan 1, 1960

By Benjamin Cebrian

Metallurgical testing at Cobre Las Cruces prior to production at the mill was done with overburden gossan. Some of that test gossan was a very fine material, wet by the water conditions at the bottom of the pit. When processed and stored wet at the fines material 3000 tonne (3307 tons) silo, this material cemented in a very unusual manner.

Jan 1, 2010