Search Documents

By Kenji Morinaga, Shigeru Fujino

"Preparation and vacuum ultraviolet (VUV) transmission spectra of aluminum fluoroberyllate glasses, MgF2-CaF2-SrF2-A1Fr BeF2 (MCSA-Be) and MgF2-CaF2-SrF2-AlFrYFrBeF2 (MCSAY-Be), were studied. The influence of YF3 and BeF2 on the thermal stabilization against crystallization and VUV transmittance was investigated. With increasing the BeF2 content, the crystallization tendency decreased and the absorption edge shifted to shorter wavelength in the MCSA-Be and MCSAY-Be glasses. The MCSA-20Be glass composition exhibited the shortest wavelength UV absorption edge (-147 nm) and the highest transmittance at 157 nm (60% for 2 mm sample thickness). The transmission values at 157 nm and the slope (steepness) of the absorption edge were found to be significantly influenced by the trace amount of Fe2+ derived from the BeF2 raw materials.IntroductionPure beryllium fluoride is known to be an only fluoride that forms one component glass on cooling from the molten state and is structurally similar to silica with [SiO4]4- tetrahedra. Molten BeF2 is highly viscous with a viscosity of about 106 poise near its liquidus temperature at 550""C[l]. The addition of modifying fluorides such as LiF, NaF or KF to BeF2 substantially decreases the viscosity[2]. Glass forming region of binary fluoroberyllate glasses has been mainly reported by several authors [3]. LiFBeF2 binary system is structually analogy for Mg0-Si02 system from their phase diagram and ratio of ionic radius for each cation and anion, respectively. LiF-BeF2 binary glasses seems to be promising candidates for the extreme deep vacuum ultraviolet (VUV) transmitting optical materials owing to their larger band gap. However, it is chemically unstable, and so, have no practical application for lens systems in micro lithography equipments and substrate materials for F2 (157nm) excimer laser[4]. There are also few reports on the VUV transparency of multicomponent aluminium fluoroberyllate glasses from the view point of their compositional dependencies. The purpose of this paper is to prepare deep VUV transmitting optical materials and determine the optimum glass compositions for aluminium fluoroberyllate glasses investigating their thermal stabilization against crystallization."

Jan 1, 2000

By K. Narayan Prabhu, W. D. Griffiths

"Heat transfer during the unidirectional solidification of a cast iron alloy against cast iron chills was investigated using an inverse modelling approach. Chills of thickness 100 mm and 10 mm were used, to simulate gravity die cruiting conditions and the use of chills in sand moulds. In both cases transient heat transfer, measured by the interfacial heat flux and heat transfer coeffieient; declined from initially high values in the first few seconds of solidification, to values about an order of magnitude lower which persisted for the remainder of the experiments. In the case of the thin chill it became saturated with heat until it was no longer in a position to extract further heat from ·the casting. These results were interpreted by studying the resistance to heat transfer from the casting offered by the ·casting-chill interface and the chill itself for example, the thermal resistance of the casting-chill interface can be influenced by the deformation of their respective surfaces and their subsequent relationship.IntroductionDie casting cast iron offers several advantages such as energy savings, higher mould yield, and better surface quality over the sand casting process1 • The process is· environmentally' friendly because of the elimination of the sand. However the design and construction of metallic moulds is expensive and a faulty die design may result in a defective casting: A simulation based process design of die castings would enable die designers and solidification modellings to try better designs of dies on the computer and arrive at a cost effective solution more quickly. This has numerous benefits for the die caster, as he would be able to produce sound castings with very short lead times.The success of a solidification model to predict accurately the thermal history and the location of hot, spots inside a solidifying casting depends to a large extent on the heat transfer data prescribed at the metal/mould interface. Many measurements of the heat transfer coeffident (or the heat flux) between a solidifying aluminum alloy and a chill have shown that the heat transfer coefficient is a function of most of the variables of the casting process2 - 8. However heat transfer studies during the solidification of ferrous alloys are rather limited. The high temperatures involved suggest that the contribution due to radiation heat transfer cannot be neglected."

Jan 1, 2000

By Jean Igor Margem, Rômulo Loiola, Sergio N. Monteiro, Foluke S. de Assis, Frederico M. Margem

"Fibers extracted from the ramie plant have been traditionally used in textile and are now being considered as polymeric composite reinforcement owing to their superior strength. Recently the mechanical behavior of ramie fiber reinforced polyester composites was investigated but no significant improvement was found. Therefore, the objective of this work was to carry out a similar investigation by changing the type of polymeric matrix. Specimens with up to 30% in volume of ramie fibers incorporated into epoxy were bend-tested until fracture. The results showed a moderate improvement with a tendency of decreasing stress for higher amounts of ramie fibers due to the weak interface developed with the epoxy matrix.IntroductionThe engineering application of natural fibers extracted from cellulose-containing vegetables, also recognized as lignocellulosic fibers, is presently considered an environmentally correct alternative to replace more expensive, non recyclable and energy-intensive synthetic fibers [1-3]. In fact, composites reinforced with traditional fibers such as coconut, sisal, jute, hemp, etc ... are already on the market in substitution for common glass fiber automobile components [4-6]. Even less known fibers like curaua from the Amazon region are being industrially used [7]. Economical and environmental reasons sustain a promising future trend for natural fiber composites. In comparison with the less expensive glass fiber among energy-intensive synthetics, lignocellulosic fibers are approximately five times cheaper. For the current situation of our planet, natural fibers are regarded as ""green"" environmentally friendly materials. They are abundant, renewable, biodegradable, and recyclable, above all, neutral with respect to carbon dioxide emission, associated with global warming.Several relatively unknown lignocellulosic fibers such as piassava [8], sponge gourd [9], sugar cane bagasse [10], buriti [11] and ramie [12], with simple and limited applications, or just byproducts, are now being investigated for their potential as composite reinforcement. This could widen the offer of new lignocellulosic fibers for composite reinforcement. The banana fiber, in particular, has a tensile strength around 700 MPa [13], which is comparable to the strongest lignocellulosic fibers used as composite reinforcement.In addition to polyester, the epoxy is another relatively strong polymer used as composite matrix. Therefore, the objective of the present work was to assess the mechanical properties obtained by flexural test, for epoxy composites reinforced with different amounts of banana fibers."

Jan 1, 2013

By D. F. Liub, Z. Y. Liu, W. Y. Xue, Y. F. Shenb, Y. D. Wang

"The microstructure characteristics and deformation behavior of ultrafme grained (UFO) 304SS fabricated by accumulative rolling and armealing have been investigated by means of tensile tests, electron-backscatter-diffraction (EBSD) and transmission electron microscopy (TEM) techniques. The volume fraction of martensite phase decreases with increasing armealing temperature. In the grain sizes ranging from 300 nm to 10 µm, the strength held Hall-Petch relationship. The sample with an average grain size of 300 nm exhibited extra high yield strength of 1700 MPa and a tensile strength of 1780 MPa, while the elongation retains 12%. The limited uniform elongation in the UFO materials could be explained in terms of plastic instability. Very interestingly, for the bulk material with an average grain size of 1.200 µm, the high yield strength and uniform elongation were simultaneously achieved to be as 1000 MPa and 18%, respectively.IntroductionUltra-high strengths have been achieved in elemental metals by employing heavy plastic deformation, or by creating ultra-fine-grained (UFO) structure. Here UFO materials are defined as polycrystalline solids with property-controlling microstructural features below the 1 µm level. Typical processing routes include severe plastic deformation (SPD) [1, 2], which decomposes the grains through dislocation accumulation and reorganization (polygonization). Several different kinds of SPD process for bulk materials are typically as equal-charmel angular pressing (ECAP) [3], high-pressure torsion (HPT) [4] and accumulative roll-bonding (ARB) [5]. One of the main motivations for such a push for the very small grain sizes stems from the expectation of unprecedented mechanical strength, as predicted by the well-known Hall-Petch relationship that projects a continuous rise of strength with decreasing grain size [6]. However, these ultra-high strength metals no longer have the high ductility typical of their conventional coarse-grained counterparts, because the undesirable inhomogeneous deformation on the microstructure level can lead to the early onset of failure, severely limiting the useful ductility [2]. Recently, the interesting strategies have been performed to increasing simultaneously the ductility and strength ofUFG pure copper and nanostructured alloys by Zhao et al [7, 8]. In a pure copper, a high ductility has been achieved without sacrificing strength by introducing a high density of pre-existing twins and a large fraction of high-angle grain boundaries. Their encouraging results trigger our motivation to obtain high strength and ductility from the commercially bulk material."

Jan 1, 2013

By Masahiro Yoshimura, Sergiy Korablov

"Hydi-othermal corrosion ofTiN, TlAlN and CrN PVD films (3 µm thick) deposited on SUS-304 substrate was studied in 100MPa water in 20-950°C temperature range up , to 750h. The beginning temperature of their reaction was determined as 200°c for TiN and TiAlN and 500°C for CrN films, which are quite low in comparison with that of air oxidation of those powders. Very thin oxide scales. of TinO; n-I homologous series phases were formed above 300°C. TiO2 anatare. is observed for TIN and TiAlN films at 400°C. The· feature of hydrothermal corrosion of CrN films seems to be CrNxOy phase formation.Distinguishable weight changes were observed at higher temperature than 700°C for TiN, 750°C for· TiAlN and 800°C for CrN respectively. Hydrothermal corrosion kinetics .was constructed to calculate the activation energy of hydrothermal corrosions. On the base of obtained data, hydrothermal corrosion resistance was as follows: TiN – TiAlN - CrN. Facetted oxide crystals were formed at higher temperature than 500°C for TiN, TiAlN and 850°C forCrN.IntroductionThe metallic nitride (TiN; TiAlN, CrN) PVD films have high hardness, strength and wear resistance. Therefore these films are widely used in industry for wear resistij.nce application such as cutting tools and die molds. Their performances depend on not only the mechanical properties but also corrosion resistance of coated films. High temperature oxidation of metalliq nitride and nitride films was well studied [1-5]. However there are no reliable data concerning the .corrosion resistance of coated nitride materials. In high-temperature and high-pressure water. There are a few reports on hydrothermal corrosion of nitride films [6,7]. The increase of corrosion resistance of CVD films was observed in following succession TiC - TiCNO - TiCN - TiN at 300-680°C temperature interval and I 00 MPa pressure water according to data of the first report. Kawana et al. [7] have reported about excellent corrosion resistance of CrN films under 290°C and 8, 6 MPa water during I 000 h in the circulating type experimental loop. The films thickness was about 7-10 µm in both cases. However it remains unclear the chemical state of the surface species and especially in-depth distribution, oxide scale thickness and its growth, and defects formation in the oxide film."

Jan 1, 2000

By Jie Li, Thomas A. Rawdanowicz, W. J. Collis, S. Venkatraman, S. Iyer

"InSb being the lowest band gap. material amongst the 111-V semiconductors with low effective mass has long attracted research interest, due to its potential application in far infrared devices and for high speed circuit elements. In this paper, we report, for the first time, Te-doping of InSb on GaAs substrate using SnTe doping source with molecular beam epitaxy (MBE) technique and its electrical characterization. The undoped epilayers are n-type in the temperature range of 10 K to 300 K investigated. The room temperature (RT) mobility as high as 64,810 cm2/V·s (1.9x1016 cm-3) have been measured on a 4.8 µm thick epilayer. Sn Te doping at different doping levels were investigated. 5. 7 µm thick doped layers with RT carrier concentrations ranging from 2x1016 cm-3 to 3.2x1018 cm-3 with corresponding full width at half maximum (FWHM) of x-ray (400) rocking curve varying from 170-200 arc-seconds have been achieved. The Hall mobility of 20,000 cm2/V·s at 1.3xl018 cm-3 carrier concentration was obtained indicating that SnTe is a good candidate as source material for n-type doping of InSb.IntroductionThe thin films of InSb and InSb-based alloys have found considerable interest because of potential applications in III-V semiconductor-based infrared optoelectronic devices1• In addition, the advantage of the small effective mass and the consequent high mobility can be utilized in high frequency and high-speed circuit devices2 InSb can also be used in magnetoresistive sensors for position sensing3. Epitaxial InSb films grown by MBE may be doped n-type with Si or Sn, or with the group VI elements, namely, S, Se, or Te. Of the group VI elements, Te may be advantageous because of its relatively low vapor pressure. However, the vapor pressure is high enough to have sufficient memory effect during MBE growth. Hence different telluride compounds such as GaTe45, PbTe6 and Sb2Te37 have been used as the dopant source for Sb-based compounds. SnTe has also been used as a successful n-type dopant in the MBE growth ofGaSb8 But, to our knowledge, there is no report on the investigation of SnTe doping of InSb. In this paper, we report the first doping characteristics of SnTe in InSb layers grown on GaAs substrate."

Jan 1, 1998

By M. M. Sadawy

"The increased rate of exploitation of iron ores has resulted in a rapid depletion of high-grade iron ore deposits in Egypt. New iron reserves have to be discovered to secure the iron ore for steel production. This paper aims to study the characterization and magnetic separation of low grade Aswan iron ore. The results showed that Aswan iron ore is composed of oolitic hematite, goethite, quartz and kaolinite. The screen analysis indicated that Aswan iron ore had a uniform distribution of iron and silica in the different particle size fractions and there is no any particle size has high amount of iron or low content of silica. On the other hand the results of dry high intensity magnetic separation illustrated that this technique is not suitable for upgrading this ore.IntroductionIron is one of the common metals used in industry, as well as being the fundamental raw material used in iron-steel industry; products are wide spread even in daily uses. The total iron ore reserves of the world have been estimated as 3 70 billion tones; 160 billion tones is classified as economical, while 210 billion tones as potentially economical [1]. An estimated 98% of the iron ore exploited in the world is used in the manufacture of pig iron and steel, which are non-substitutable backbones of modem society. The rapid increase of world steel production over the last few years have required an equal increase in iron ore production, from 876.8 Mt in 2006 to 948.1 Mt in 2007 [2]. The increased rate of exploitation of iron ores has resulted in a rapid depletion of known high-grade iron ore deposits. This, in turn, has led to a dramatic increase of prices. In the absence of any major new discoveries of high-grade iron ore deposits, mining companies have turned to lower-grade materials to assess their beneficiation potential to expand their production base and beneficiation capacity, in order to satisfy future demand. Egypt is going to face shortage in iron production, consequently new iron reserves have to be discovered to secure the iron needed for the country [3]. Exploitation of low grade ores requires special equipments and techniques for recovery of minerals values. High gradient magnetic separators offer promise and great potential of application both technologically and economically in the processing of fine particles containing weakly or feebly paramagnetic components [4-6]. Within this existing framework, this research was initiated to assess the beneficiation potential of low-grade Aswan iron ore by high intensity magnetic separation."

Jan 1, 2013

By Yuanyuan Wang, Hong Li, Xueting Liu, Hao Bai, Kang Zhou

"Phase change materials are widely used in efficient utilization of energy and new energy technology. Especially, more attention has been paid to composite phase material, which is applied on architectural energy-saving and efficient working fluid. In this paper, stearic acid-silicon dioxide composite material was prepared by sol-gel process from tetraethyl orthosilicate (TEOS) and stearic acid (SA). The material was investigated by Field emission scanning electron microscopy (FE-SEM), Fourier transform infrared spectroscopy (FT-IR) and Differential scanning calorimeter (DSC). The FE-SEM results show that 3D-grids of silicon dioxide were formed clearly and SA was encapsulated in the silicon dioxide shell. The FT-IR results show that there were no chemical reactions between silicon dioxide and SA, which is the chemical property of the composite material, is stable. The DSC results show that the composite phase change material has favorable heat capacity. This material is expected to be used to make a cooling working fluid.1. IntroductionEnergy thermal storage becomes increasingly prominent issue in recent years, because thermal storage has been used in many aspects, for example, it can be added into building materials to improve heat conditioning. Another potential application of thermal storage materials is that the intermittent waste heat can be collected and recycled effectively by using the thermal storage facility. Thus, energy thermal storage plays a significant role in conserving available energy and improving its utilization [1]. Energy thermal storage includes sensible heat storage and latent heat storage. The latent heat storage has great heat density with a constant temperature during the phase change process [2-5]. Large quantities of latent heat storage will be absorbed and released when phase change takes place. Based on the former researches, some phase change material (PCM), such as fatty acid and paraffin waxes, has been proved to have high latent heat storage capacity and appropriate thermal properties [5-6]. However, using the PCM in energy storage systems directly is restricted, e.g. some properties of organic PCM, like form-stability and thermal conductivity, are not good enough to use. Meanwhile, almost all the inorganic PCMs are corrosive and most materials may cause sub cooling and segregation [7-9].The other problem is that the leakage when the temperature reaches the phase change point. Therefore, encapsulated composite phase change material (CPCM) emerged in order to solve the problem of leaking out, minimize the sub cooling and prevent phase segregation. [10-13] However, the easy flammability of fatty acid also has hindered the development of PCM. Accordingly, it has been found out that silicon compounds are environmentally friendly promising substitutes for halogen-containing flame retardants. Especially, silsesquioxanes are excellent in the flame retardancy. So CPCM can be encapsulated with SiO2 acting supporting material."

Jan 1, 2014

By Gerald Onyedika, Tochi Onwumere, Martin Ogwuegbu

"The kinetic study for the leaching of iron from cassiterite ore in KOH solution was studied. The effects of KOH concentration, particle size and reaction temperature on the leaching rate of iron were also examined. The results of leaching studies showed that the leaching of iron from cassiterite ore in KOH solution is significantly influenced by the reaction temperature, KOH concentration, and decrease in particle size. The study showed that 90.62% of iron ore was leached in 8M KOH solution at 80°C within 120 minutes. The experimental data were well evaluated using the shrinking model for surface chemical reaction and diffusion control through the product layer. The activation energies for the iron ore dissolution using the two models were calculated to be 32.06KJmor1 and 97.97 KJmor' respectively.IntroductionIn recent times, there has been increasing attention on the kinetic study of mineral dissolution. In most of these studies, the experimental results were analyzed with a suitable shrinking core model under the assumption that the ore is a homogeneous spherical solid phase [1-4]. A study of the dissolution kinetics of a Nigerian cassiterite ore by hydrochloric acid showed that increase in the hydrochloric acid concentration is accompanied with increase in the amount of cassiterite ore dissolved at various times [4]. The optimal concentration was found to be 4.0M HCl, after which there was a decline in the amount of the ore dissolved, which showed that the concentration of the reagent has a significant effect on the leaching rate of the ore. Also in studying the effect of stirring speed on the rate of cassiterite ore dissolution while keeping other conditions constant for 120 minutes, the result showed that the rate of cassiterite ore dissolution was dependent on the stirring speed over a range of 0 to 630 rpm. Above 360 rpm, the stirring speed no longer had any effect on the solid dissolution. The dissolution rates of cassiterite were analyzed using a suitable shrinking model. The results showed that the reaction was controlled by the diffusion of tin through the porous product layer, a reaction order with respect to hydrogen ion concentration of 0.92 M and activation energy of 50.05KJmor'. In another kinetic study on the leaching of a low grade niobium-tantalum ore with concentrated KOH solution the effect ofreaction temperature, KOH concentration, agitation speed, particle size and alkali-to-ore mass ratio on the dissolution rate of niobium were examined [5]. The result of niobium leaching from low grade niobium-tantalum ore with concentrated KOH, solution at different agitation speeds showed that the dissolution rate increased with increase in agitation rate. In the case of particle size effect, the results show that small particles require much shorter time for complete dissolution than the large ones."

Jan 1, 2013

By E. S. Geskin, W. L. Chen, A. Vora

"This paper is concerned with the application of an abrasive waterjet for metal shaping. The waterjet cutting technology uses water compressed to the pressure up to 55,000 psia which is accelerated in a cylindric nozzle. Abrasive particles are then supplied into the water stream and accelerated by the water. Cutting occurs via the interaction between the water-particles stream and a workpiece that causes material erosion at the impingement zone. The mechanism of this interaction enables shaping of practically any material with a minimal effect on the metallurgy of subsurface. The motion of the jet penetrating through a material body is guided by a robotic arm. A waterjet cutter is becoming one of the principal tools for shaping titanium, super-alloys and other hard-to-machine metals and composites. The shaping, resulting from the waterjet cutter, is very similar to laser beam cutting. However, unlike laser processing, there is no damage to the subsurface structure.The presented work discusses the experimental study of cutting of titanium plates. The results of these experiments demonstrate the potential of the abrasive waterjet as a shaping tool. IntroductionOne of the main avenues in the development of metal shaping is the use of high energy beams as cutting tools (1,2). There are a number of advanced beam oriented material removal technologies, such as laser, electron beam, plasma and abrasive waterjet (AWJ) cutting. The advantages of AWJ cutting are well understood and documented (3-14). This technology has the potential of becoming the principal tool for netshaping and netsurfacing of parts. However, the use of AWJ is currently limited to cutting of hard-to-machine materials such as titanium, superalloys, glass, composites, etc. The cost of A W J cutting is much higher and the productivity is much lower than those of the thermal cutting. At the same time abrasive waterjet can be used for shaping any existing technological material from fabrics, plastics, aluminum to glass, composites, and diamonds. The material losses during AWJ shaping are minimal. The roughness and waveness of the surfaces generated during AWJ cutting are substantially less than those of the thermal cutting. Due to the size of the jet cross-section total force exerted by the jet on a workpiece does not exceed 30-50 newtons. This terminates the need in the use of complex fixture for material holding. Low applied forces and low surface temperature prevent the damage of metal subsurface in the course of cutting. The small size of the impingement area will determine the limited width of the kerf. Due to the size of kerf and unidirectional character of the water jet the formation of practically any metal contour is possible."

Jan 1, 1988

By Masatsugu Morimitsu

"The novel smart anode, MSA ™, for electrowinning of non-ferrous metals such as copper, zinc, nickel, and cobalt has been developed by thermal decomposition. The smart anode consists of a titanium substrate coated with a catalytic oxide layer which comprises amorphous or less crystalline oxide coatings. The catalytic layer contains an iridium oxide-based mixture or a ruthenium oxide-based mixture. The smart anode provides a remarkable reduction in cell voltage compared to other anodes, e.g., commercially available coated titanium electrodes and lead alloy electrodes. The test data has demonstrated that a maximum voltage reduction by ca. 30% is possible compared to lead alloy anodes. The smart anode also gives some additional merits in suppressing unwanted deposits on the anode; i.e., deposition of MnOOH, Pb02, or CoOOH. The electrowinning with the smart anode is possible to be an environmentally friendly process with less energy consumption and less anode deposits.IntroductionA coated titanium electrode iridium oxide-based or ruthenium oxide-based catalytic layers is well known as an insoluble anode for oxygen or chlorine evolution in industrial electrolysis such as chloro-alkali electrolysis, electrogalvanizing or electrotinning of a steel, a thin film production by electrodeposition such as copper foil production (CFP), water electrolysis, and electrowinning of nonferrous metals. The anode is commercially produced by thermal decomposition of a precursor solution painted on a titanium substrate, and the decomposition is usually performed at 450 °C or more. The obtained catalytic oxide coating formed on the substrate contains crystalline oxide as an active component to oxygen or chlorine evolution. The author of this paper had met a problem of such a crystalline oxide coating in the application of copper foil production; the anode was unable to use for a long period because of a large amount of lead oxide (Pb02) deposited on the anode, and the cell voltage was seen to continuously increase and drastically rise by the accumulated Pb02. In this case, the voltage reduction by replacing a lead alloy anode with the dimensionally stable anode was initially observed, but was gradually lost and disappeared. Therefore, the author of this paper aimed and investigated to suppress the unwanted side reaction on the anode, and finally invented a new class of coating based on an amorphous iridium oxide mixture in 2003 [!]. The invented coating was obtained at a low temperature thermal decomposition, e.g., 360 °C, and the coating consisted of amorphous iridium oxide and amorphous tantalum oxide. This invention achieved that oxygen evolution potential shifted more negative so that the cell voltage was reduced, and no Pb02 was deposited in the electrolyte of CFP [2,3]."

Jan 1, 2012

By Guozhu Ye, Mikael Larsson, Eric Burström, Sten Ångström

"Increased use of scrap in steelmaking including scrap use in BOF has a high economic and environmental potential in terms of increased productivity, energy saving and reduced emission of CO2. Preheating and surface cleaning of steel scrap is a concept developed by MEFOS in a four year research program funded by MISTRA, Swedish Foundation of Strategic Environmental Research. The process concept consists of four major steps: 1) Combustion of ASR or other waste fuel and composing of the gas composition. 2) Scrap heating and cleaning in a shaft where the coated zinc is removed as ZnCl2 and scrap is heated to about 600 ºC. 3) Dust separation for recovery of metal zinc. 4) Gas cleaning. This paper will describe the process concept and highlight the major results from preliminary trials around the scrap heating and cleaning shaft.IntroductionSteel is often coated to increase the corrosion resistance. Share of coated and galvanized steel in the world marked is steadily increasing. This results in increased amounts of scrap with different types of coatings. Use of galvanized scrap in EAF plant results in an EAF dust with high content of zinc ferrite and many other impurities like Pb, Hg, Cd and halide. EAF dust is classified as hazardous waste in most of the developed countries and the steel plant has to pay for external treatment for zinc recovery. For use in BOF plant this will result in a BOF dust containing typically 1-5%Zn making it impossible for recycling to the blast furnace.Different approaches for surface cleaning have been investigated in past. Dapper et al. [1] examined the possibility to evaporate Zn, Ni, Cr, Sn from coated materials using chlorine. Chlorinated rinsing of non iron oxides and metals using HCl from combustion of PVC was discussed by Fray [2]. Further studies by Tee and Fray [3-5] have been concentrated on the possibility to vaporize coatings with an air and chlorine gas mixture. The O2:Cl2 ratio in the gas mixture was found to have great importance for control of the process. To avoid the chlorination of iron, this ratio should be kept at a level of 10:1.Scrap pre-heating up to about 600 ºC is a well known method and this alone could save up to 100 kWh per ton steel. The technology has been established since many years and efficient processes were developed in the 90’s. However, no process has fully gained the expected energy savings as the large quantity of the exhaust gas has to be reheated to over 1000 ºC again to destroy the hazardous components like dioxins."

Jan 1, 2008

By Suleyman Tekeli, Serdar Salman, Bulent Aktas

"The effect of La2O3 content up to 15 wt% on phase stability, sintering and microstructure of cubic zirconia (8YSZ) was investigated. XRD results showed that the specimens containing up to 15 wt% La2O3 were composed of only cubic structure. Also, the specimens doped up to 5 wt% La2O3 revealed no La2O3 peaks, indicating that La2O3 was completely solubilized in the cubic structure. However, when> 5 wt% La2O3 was added, the peak of La2Zr2O7 compound emerged, showing that the overdoped La2O3 was not solubilized in the 8YSZ matrix. The lattice parameter of the 8YSZ slightly decreased with the increasing La2O3 content up to 1 wt% but further increase in the La203 amount resulted in an increased lattice parameter. The comparison of grain size of the 8YSZ specimens with various La2O3 content showed that grain size slightly increased with the increasing La2O3 content up to 1 wt% but further increase in the La2O3 amount resulted in a decreased grain size.IntroductionAt atmospheric pressures, three polymorphic forms of Zr02 are stable at different temperatures i.e. monoclinic, tetragonal and cubic. A high-pressure orthorhombic form of Zr02 has also been reported[l]. The successful production of pure Zr02 bodies is not possible all the time due to the large volume expansion associated with the martensitic tetragonal-monoclinic transformation. This fact restricts the applications of zirconia, in spite of its excellent mechanical and thermal properties. However, the stabilization of the high temperature polymorphs at room temperature as stable phases is made possible by addition of suitable dopants. Fully stabilized cubic Zr02 and partially stabilized tetragonal Zr02 show interesting properties and are widely used as ionic conductors, coatings and gas sensors in solid oxide fuel cells and structural applications[2]. Most frequently used dopants include Y203, CaO, MgO and Ce02, although other oxides, such as those of rare earth elements, can also act as stabilizers of the high temperature structures. The incorporation of aliovalent cations to the lattice, forming substitutional solid solutions, allows to control the concentration of anionic vacancies in the structure. This aspect is particularly important in designing ionic conductors[3], and is also determinant in the stabilization process[ 4]. The process of stabilization with larger ionic radii dopants is rationalized by the crystal chemistry model[ 5], that describes the dopant cations as typical stabilizer when they have larger ionic size, lower charged state and higher ionicity than Zr4+ The ionic radius of Zr4+ is 0.84 Å and that for La3+ is 1.016 Å [6]."

Jan 1, 2012

By Norbert Hort, Karl Ulrich Kainer, Carsten Blawert, Daniel Fechner

"With the development of new heat resistant magnesium alloys, the automotive industry has introduced several parts to the drive train. The rising number of large magnesium components will result in a higher quantity of automotive post consumer scrap and the changing legislation will force car manufacturers to take magnesium recycling into consideration. So far post consumer scrap has not been used for magnesium alloy production. Quite a reasonable amount of automotive scrap is likely to end up in a mixed light metal shredder fraction. The separation of mixed magnesium scrap according to several alloys is complex. Therefore secondary magnesium alloys made from blended post consumer scrap would be useful. For this work a matrix of potential recycling alloys was prepared by chill casting and high pressure die casting. The materials were investigated for their microstructure, mechanical properties, heat resistance and corrosion properties. The results will be presented in this paper.IntroductionWithin the last ten to fifteen years several heavy magnesium parts have been assembled in passenger cars, such as gear box housings and crank cases [1, 2]. Reasons are the lately developed new heat resistant alloys and the increasing responsibility of automotive manufacturers to reduce the vehicles weight and thereby CO2 emissions. The latter is pushed by international legislation [3, 4]. The rising quantity of magnesium in automobiles will result in an increasing amount of so called post consumer scrap at the end of the vehicles life.So far magnesium recycling was done only for clean scrap that is free from impurities, contaminations and sorted according to a chemical composition or a single alloy respectively [5- 15]. The latter is also called class 1 scrap and mainly consists of sprues and runners from magnesium die casters [15, 16]. For the upcoming automotive post consumer scrap the materials quality strongly depends on the way end of life vehicles are treated. By proper dismantling of old cars, the bigger magnesium components could be collected and possibly treated similar to class 1 scrap [15]. Up to date automotive manufacturers have no uniform recycling system for end of live vehicles. Most probably a considerable quantity of old cars will be shredded. The resulting light metal shredder fraction will contain aluminium and magnesium scrap, both from several alloys. A separation of mixed magnesium and aluminium scrap is feasible according to [17]. Other authors claimed that the grade of separation of magnesium from aluminium is still not sufficient for a proper industrial recycling process of magnesium post consumer scrap [15, 16]. If an automatic sorting is possible it will probably be very expensive [18]. Therefore, so far the main use of post consumer scrap has been the steel desulphurisation and aluminium production [15]. The use of post consumer scrap for magnesium alloy production has been considered already by [15] and [16] but some problems have to be approached."

Jan 1, 2008

By S. Goto, S. Yamashita, K. Hata

"The average consumption of zinc dust for purification of zinc leaching solution is more than 25 kg per tonne of electrolytic zinc. Authors proposed to remove impurities in zinc leaching solution by electrolysis instead of cementation by zinc dust. The effects of copper and arsenic on electrodeposition of cobalt in zinc sulfate solution were examined fundamentally using a potentiostat. It is observed that cobalt is easily deposited on a cathode at potentials under -480mV with arsenic. Mesh cathodes of stainless steel and lead anodes were used in a small electrolytic cell and the electrolyte was circulated through 'the electrodes during the electrolysis. The effect of electrolyte circulating rate , pH, cell temperature, current density, and concentration of copper and arsenious ions on removal of cobalt were studied. Removal of Cd and Ni are also examined.IntroductionCobalt is difficult to remove from a zinc leaching solution by a simple cementation reaction using zinc dust. However, it is easily precipitated by zinc dust with co-addition of arsenious or stibinous oxide and copper ion in practical operations(I), (2), (3). The consumption of zinc dust for purification is 16-152 kg per tonne of electrolytic zinc and 65% of this zinc dust consumption is used for cobalt purification. The average retention time for purification of cobalt is 4.5 hours (1). A more economical process for purification is desired instead of zinc dust. The mechanism of this acceleration effect of copper and arsenious oxide on removal of cobalt are explained by the authorsas follows; a galvanic cell is formed between zinc dust and copper which is precipitated firstly, and cobalt is reduced on copper as Co-As alloy by this galvanic current(2). This assumption was confirmed in experiments using a galvanic cell with a membrane( 4). The following galvanic reactions occur between zinc dust and copper precipitate; on copper cathode,2H+ + 2e -= Hz(g)2Coz+ + 2HAs02 + 6H ++ 10e -= 2CoAs + 4HzOand on zinc anode,Zn = Zn = 2+ 2e –This galvanic current becomes almost zero in a zinc sulfate solution which includes only cobalt and no arsenious oxide, and cobalt is weakly deposited on a copper cathode. Cobalt deposition requiers a high degree of cathodic polarization. However, the galvanic current flows almost constantly in an electrolyte, which includes arsenious oxide, and the cathode potential is kept at about -500mV. Cobalt is precipitated as Co-As on the cathode.The authors assumed that cobalt may be removed by electrolysis at a very low current density instead of zinc dust and the following experiments were carried out. In the first part of this paper, the fundamental experiments using a potentiostat on the behaviour of cobalt in zinc sulfate solution are described. In the second part, the results of the electrolysis are reported. Cobalt is removed by a new type of an electrolytic cell, which was desigoed to <Iccelerate the rate of deposition of cobalt. The removal of cadmium and nickel in a solution which includes cobalt and arsenic are also examined."

Jan 1, 1997

By M. F. Hochella

Transmission electron microscopy (TEM) and energy dispersive X-ray (EDX) analysis have been used to study the mode of occurrence and mineral associations of gold in partially oxidized high grade gold ore from the Carlin sediment-hosted deposit. Rounded.gold particles have been observed that range in size from 0.03 to 0.1 p.m (300 to 1000 A) in diameter. The gold is associated with maghemite h-Fep3l and a K-Al-Si-bearing phase that is suspected to be illite. Detailed descriptions of gold and its mineral associations in &apos;Carlin-type&apos; gold deposits are critical not only to understanding the mechanism of fluid transport and precipitation of gold, but also to developing improved metallurgical techniques for the recovery of gold from refractory ore. Direct observation of gold in unoxidized ore is rare due to its relatively high degree of dissemination and low average bulk concentration which averages 9 ppm according to Radtke (1). Hausen and Kerr (2) observed 1 to 5 p.m grains of gold directly in oxidized ore but these microscopically visible particles account for only a small percentage of gold present in the ore. The samples used in this study were selected from individual beds of high grade, partially oxidized ore (4.55 oz/ton or 156 ppm gold) that were collected in the Main pit of the Carlin mine. The samples were collected from several thinly laminated carbonate micrite beds within the top 50 meters of the Roberts Mountains Formation. The carbonate micrite has been altered by hydrothermal fluids to a calcite-absent, moderately silicified rock referred to as alteration zone #3 by Bakken and Einaudi (3). Based on petrographic and SEM studies, the samples contain carbonaceous matter, and both pyrite and iron oxide pseudomorphs after pyrite. The oxidation of pyrite may be a pro-duct of deep weathering, in which case limited remobilization of gold may have occurred. TEM sections of the rock were prepared by first embedding small chips in low viscosity epoxy. The epoxy blocks were cut with a Reichert Ultracut E ultramicrotome, producing thin sections less than 0.1 p.m thick. The sections were examined with a Phil-lips 400ST TEM at 120 keV in both imaging and selected area diffraction modes. Native golci*was easily detected in TEM bright field images due to the large electron density contrast between gold and all other phases that are present (Figs. 1 and 2), Gold was positively identified with high spatial resolution EDX analysis in the transmission electron microscope, although selected area diffraction of individual grains was not successful EDX analyses of the platy and massive minerals immediately surrounding the gold particles typically indicate the presence of Si, AI, K, and Fe, However, the d-spacings derived from selected area diffraction of these polycrystalline masses (as, for example, in Fig. 2) give an exact match for maghemite. As a result, there is no diffraction information to identify the K-AI-Si-bearing phase(s). The lack of a diffraction pattern could be due to either electron beam damage or to a poorly crystalline phase(s).

Jan 1, 1987

By Xin-liang Gao, Qing Li, Gui-qin Fu, Duo Jin, Miao-yong Zhu

"Optical microscope together with alternative wet-dry cyclic accelerated corrosion tests and XRD, SEM were employed on bridge weathering steel samples with different Mn and Ni contents which were vacuum induction melted and rolled to study their effects on the microstructure and rust layer evolution in er' containing condition. The results show that the microstructure is mainly ferrite and pearlite when Mn and Ni contents are 0.75 %, 0.42 %, respectively. Both the increase of Mn and Ni contents will make pearlite disappear while granular bainite appear, meanwhile the grain size decreases. With the increase of Mn content, the corrosion rate decreases in the initial stage, but the effect becomes little in the later stage. The increase of Ni not only improves the corrosion resistance of steel base at the initial stage but also hinders the tendency of further corrosion. As Mn content increases, a-FeOOH contents in rust layer decreases. With increase of Ni content, the content of a-FeOOH in the rust increases while that ofy-FeOOH decreases.IntroductionWeathering steels had been ~radually applied in manufacture of bridges owing to reducing the corrosion rate remarkably [I- l .Good weldability was needed for high performance bridge weathering steels. Since carbon was thought to be bad for weldability, low carbon content steel was adopted and Mn was added to amend the mechanical strength loss. Some scholars[6, 7l believed that Mn was beneficial for increasing corrosion resistance performance of the steel in marine atmospheric environment. Some scholars [S, 9l thought that Mn had little effect on corrosion resistance in marine atmospheric environment. Presently, the effect of Mn on bridge weathering steel in marine atmospheric environment still remained poorly understood. Ni was considered to be beneficial for increasing corrosion resistance performance in marine atmospheric environment [JO-l4l However, the high cost limited its application range. What would bring to the rust and corrosion by decreasing Ni content needed further research.Most researchers assumed that microstructures only affected the corrosion behavior of bare steel. But the study of Guo et al. P5l showed that the homogenous microstructures were beneficial for the corrosion resistance of steels. The effect of Mn, Ni content change on microstructure and microstructure on corrosion still remained poorly understood. In the present work, the effect of Mn and Ni on the microstructures of steel matrix, as well as the microstructures on the rust and corrosion was investigated."

Jan 1, 2014

By Corby G. Anderson

Today, with a stringent economic and environmental climate prevailing in the copper business, there is increased interest in evaluating new processing alternatives for production. Hydrometallurgical pressure oxidation of copper concentrates is one of the more viable approaches and several technological candidates have emerged. Of these, an overlooked but, ironically the first industrially proven methodology, utilized nitrogen species catalyzation in the oxidizing pressure leach system to produce copper via SX!EW. Given its many inherent process advantages, this may prove to be a feasible process alternative for the future. In this paper, the history of the system and its application to chalcopyrite concentrates will be outlined. In particular, a novel methodology for effective recovery of precious metals from chalcopyrite concentrates will be discussed. Finally, the perceived economics of this unique industrially proven process will be delineated.

Jan 1, 2000

By Kosei Morita, Osamu Nakano, Katsuhiko Nagai, Kazuhiro Mori

"The Sumitomo Toyo Smelter and Refinery commenced its operation in 1971 with three Peirce- Smith (PS) converters. “2 hot – 1 blowing” operation was practiced, that is one of two available converters was blowing and the other was standby in a hot state while the third converter was under repair. After several improvements, the stack time ratio reached around 90%; and processing 5 batches a day became possible.As a result of the expansion program of the Toyo smelter and refinery that started in 2001, the converter operation pattern was shifted from “2 hot – 1 blowing” to “2 hot – 2 blowing” with the installation of second converter blowers and an additional ladle crane.In 2005 a, the fourth converter was installed and “3 hot – 2 blowing” operation began. Also, with improvements experienced in the anode furnaces and the anode-casting wheel operation, today, the number of cycles has been increased up to more than 8.5 a day.The treatment techniques of fugitive gas containing sulfur dioxide from converter furnaces have been gradually reinforced, and the fixation rate of treated sulfur is currently being maintained at more than 99.9%. This paper introduces the operations described above, and the improvements in environmental management techniques for the Toyo PS converter operation."

Jan 1, 2009

By Akira Kaneda

Mitsubishi continuous process employs an electric furnace for settling matte from slag. Electrodes are immersed into the slag layer in the slag-cleaning furnace and the temperature of the melt is maintained at a predetermined level by Joule&apos;s heat. Electrodes are immersed to the depth where the current of each electrode is kept at a set value, and they are raised or lowered automatically to compensate for the deviation from it. Because electric resistance of the bath is varied with the matte level in the furnace and the composition and temperature of the slag, the immersion depth of the electrodes is affected by them. Therefore by monitoring the immersion depth and its change with time, abnormal situations in the furnace, such a~ rise of matte level or local abnormal state of melt, can be detected. In this paper, relations between state of the furnace and electrode behavior are discussed based on the plant data, and then a new and simple monitoring method of the condition of the furnace is proposed.

Jan 1, 2001