Search Documents

By Jorge D. Vier, Raúl B. Rebak, Alicia E. Ares, Natalia S. Zadorozne

Recent worldwide demand has driven nickel and molybdenum prices to record high values. Alloys containing significant amounts of nickel and molybde- num, such as the austenitic and duplex grades, have experienced significant price increases and some spot shortages have resulted in some regions. With low or no nickel content and reasonable molybdenum content, super-ferritic stainless steels are now proving to be the most cost effective corrosion resistant materials. The electrochemical behavior APMT® (Fe–21Cr–5Al–3Mo–0.04C) and 4C54® (Fe–26.5Cr–0.8Mn–0.5Si) super-ferritic stainless steel in NaCl solutions has been studied using open circuit potential measurements, potentiodynamic polarization curves, and electrochemical impedance spectroscopy. The aim is to compare the behavior of these materials with austenitic stainless steel alloy 316 (Fe–18Cr–10Ni– 2.5Mo). The results indicate that the APMT alloy presents a better performance than the AISI 316 stainless steel, while 4C54® does not, especially at anodic potentials. The good behavior of APMT® may be attributed to Al and Mo content in its composition.

Mar 1, 2017

By Scott A. Shuey

Keywords: E-Waste, Pyrometallurgy Many might think addressing the issue of e-waste is a new area of study. Electronics disposal has been discussed in some circles for at least the past 25 years. The recycling of electronic waste (e-waste) tends to be a rather complex undertaking when considering the intimate bonding of materials in the average printed circuit board. The development of a recycling process is further complicated when considering the wide variety of products being generated under the heading of ?electronics.? Focusing only on the primary constituents (polymers, Cu, Al, Fe, etc.) tends to lead one to fairly simple flowsheets. Ignoring trace elements, and the various halide species generated, will lead process engineers down a development path that is sure to cause material handling issues. Researchers at Colorado School of Mines are modeling the complex chemistry that exists within the body of e-waste?comprising 39 of the known elements. An understanding of the systems thermodynamic behavior will result in the development of a more robust, long-term process for the recovery of valuable materials from the e-waste stream.

Jan 1, 2005

By W. S. Kirk

World cobalt production in 1987 was estimated to be about 26,600 metric tons (MT) of which Market Economy Country (MEC) production was estimated to be about 22,000 MT. Zaire and Zambia produce about 80 percent of the primary cobalt produced among Market Economy Countries (MEC). Production cutbacks. lowering cobalt grades and mining curtailments in Finland and Zambia in 1987, resulted in lower production than that of 1986. The trend is expected to continue through 1988. Cobalt production from Canadian ores and from Botswana is expected to increase significantly in 1988 as a result of increased nickel production. MEC production in 1988 is estimated to be 22,100 MT, only slightly higher than that of 1987. There are currently no primary cobalt mines. Virtually all cobalt is recovered as a byproduct of copper and/or nickel mining. Zaire, which produces cobalt as a byproduct of copper, is the worlds largest cobalt producer, with over 50 percent of total estimated world cobalt production and nearly 65 percent of MEC production. Zambia follows with about 14 percent and 17 percent, respectively. Zambia's cobalt production also results from copper production.

Jan 1, 1988

By Pengfu Tan

Converter slag chemistry control has played an important role in optimizing converter operations. A thermodynamic model of copper P-S converter has been developed to predict the behavior of magnetite in the converter slag. Predictions of bath temperature, slag and matte compositions, and magnetite content in the slag have been validated by industrial data. The effects of fluxing strategy, returns and skim charges, oxygen enrichment, and temperature on the magnetite formation in the slag have been predicted and discussed. Some improvements of the industrial operations have been presented.

Jan 1, 2005

By Nam-Il Um

Bottom ash contains several ferrous materials (ferrous metals, Fe3O4, Fe2O3, FeS, etc.). In particular, ferrous metals contain heavy metal because Ni and Cr are chemically attracted to iron. Likewise, Cu is used to coat Ni and Cr metals as polish or to prevent corrosion. In this study, an Fe3O4-Fe2O3 double layer (similar to pure Fe) was found to have been formed in ferrous metal during air-annealing in an incinerator (1000°C). A strong thermal shock such as one that occurs during the water-cooling of bottom ash results in the breakdown of this oxidation layer, facilitating the degradation of ferrous metals and formation of corrosion products. Therefore, Fe-ion (heavy metal) oxides may be formed on ferrous metals and may be separated from bottom ash via magnetic separation. This study sought to investigate the separation ratio of heavy metals as magnetic separation and mineralogical formation of Fe-ion (heavy metal).

Jan 1, 2006

By Patricia Martínez Nicolás

Nickel and ferronickel are some of the major components in the production of special alloys; however, the energy consumption for their production greatly increases their price. A cheaper option could be to use NiO and a reducing agent. This work presents experimental and theoretical analysis to estimate the effect of slag basicity and amount of reducing agents on the NiO reduction from the slag which interacted with molten steel at 1600 °C in an EAF. The slag system contained CaO, SiO2, CaF2 and NiO together with a reducing agent, ferrosilicon or carbon. The NiO content in the slag was 25 mass%. The amounts of the reducing agents (Si and C) were 1 to 4 times the stoichiometric mass to reduce NiO. The CaO/SiO2 ratio was 1.5 and 2.5. The kinetics of the process was very fast since after few minutes the maximum nickel yield was obtained. The slag basicity had a negligible effect on the reduction of NiO.

Jan 1, 2006

By Hang Goo Kim

A computer simulation has been carried out to predict the distribution behavior of minor elements such as Pb. Zn, Bi, Sb and As in recently proposed copper smelting and converting processes with submerged oxygen injection in which tonnage oxygen is used with a shielding gas. In this study the technique of stepwise equilibrium modeling was employed and some of the thermodynamic data were updated or reassessed. The volatilization and slagging of undesirable elements were investigated in copper smelting (steady-state) system, copper matte converting (batch) system, and the combined (smelting + converting) system at extremly high oxygen-enrichment levels. The predicted minor-element behavior under high oxygen- enrichment was compared with that in the Noranda process (normally 42% oxygen-enrichment in smelting and 24% in converting) and the reverberatory process using air. The effects of various operating parameters such as temperature, the final matte grade in smelting, the initial matte grade in converting and the O/Fe ratio in slag on the behavior of minor elements are discussed.

Jan 1, 1991

By K. Narayana Swamy

The traditional approach to improving the operating efficiency of a metallurgical plant has been to study individual unit operations and focus on improving the poor-performing unit operations. The complex nature of most metallurgical plants call for a holistic approach that will consider the whole rather than just focus on the individual units of a plant. This holistic approach is part of the systems thinking principles. Numerous case studies highlight the importance of the need to apply systems thinking principles in improving the effectiveness of metallurgical operations. Improving the efficiency of one unit operation without considering its effect on the performance of other unit operations has in many cases lead to lower overall operational efficiency. Modeling and simulation are key to the application of the systems thinking principles. Standard flowsheet models are very useful in scenario analyses though they have to be supplemented with other models for useful predictions.

Jan 1, 2006

By Vincent Menard

The purpose of the present work is to demonstrate the removal of manganese from a neutral leach zinc-rich solution ([Zn] =150 g/L) at 80°C by oxidative precipitation using a gas mixture of sulphur dioxide (SO2) and oxygen (O2). In order to determine the optimum conditions for manganese removal, several bench-scale semi-batch experiments were performed, where the effects of ORP and gas mixing were investigated. These tests showed that SO2/O2 is a fast and effective oxidant for removing manganese down to ppm level as long as the appropriate ORP is attained/maintained and gas transfer kinetics are optimized.

Jan 1, 2006

By J. Antrekowitsch

Keywords: residues, fluorides, chlorides, zinc, steel mill dust The recyclability of various nonferrous metal wastes often suffers from a relatively high fluorine and chlorine content. Both are inserted in most cases by the use of plastic contaminated scrap and a wide variety of different coatings. These halogens lead to poor product qualities and off gas contamination. Especially the history of zinc recovery from steel mill dusts shows, that the today common hydrometallurgical options are on their limit and therefore are not sufficient in most cases. This thermochemical study should give more information about different pyrometallurgical options, that offer both a chlorine and fluorine reduction and efficient zinc recovery, preferably in one process step. Selective evaporation in different atmospheres and conversion with the use of hydrogen are the main parts in this study. The results combined with the relatively small information available from literature should provide a basis for further investigations in this field.

Jan 1, 2005

By David Arana

The use of gas-water dispersion of a molten material flow onto a vibrating surface is developed as a process to minimize water pumping requirements, minimize the risks of explosions, and minimize the post solidification dewatering and fines handling equipment requirements. The process uses existing vibration transport technologies and common plant utilities. Plant trials using the smaller footprint and the progressive molten particle cooling time have yielded encouraging results. The results are analyzed and reported.

Jan 1, 2006

By Jin Qiu

Experiments were performed to determine the extent of minor element elimination that occurred when mixtures of copper smelter dust and copper concentrate, were calcined under vacuum. Almost complete removal of the As, Sb, Bi and Pb occurred due to the conversion of the minor element compounds of these elements into their highly volatile sulphides by reaction with sulphur from the concentrate. Heat and mass balance calculations of the slag-blow in a copper converter found that ~30 tonnes of the vacuum calcine could be used to produce 100 tonnes of copper as white metal. The use of dirty concentrate as the sulphidizing agent in the vacuum calcination means that the minor element treatment capacity of the smelter complex could be increased by 60 %. Also the productivity of the converters may be increased by up to 8 % due to the supply of copper values and oxygen in the calcined mixture.

Jan 1, 2005

By Antonio Huerta

The effects of potassium ethyl xanthate collector and potassium dichromate used as a depressor on a PbS mineral were studied by high frequency impedance technique. Measurements of complex permittivity, at 100 MHz suggested that is possible to obtain from isotherm adsorption the adequate industrial collector concentration being this in the range of lE-3 to 5E-3M of KEX. The e' values (320-420) in the PbS-KEX system was increased as the KEX concentration was lowered). In the other hand the PbS- K2Cr2O7 system showed higher values of e' (420-510) as the K2Cr2O7 concentration was increased. The PbS-KEX-K2Cr2O7 system was evaluated.

Jan 1, 1997

By Li Zhang

Air was blown into the molten slag as oxygen resource during the dynamic oxidation. It was found that the oxidation is not only in favour of Ti components into perovskite phase, but also the increase of slag temperature and decrease of slag viscosity during the dynamic oxidation promote the precipitation and growth of perovskite phase, average crystal size of perovskite phase is 48 µm. The experimental result realizes the selective enrichment of Ti components and coarsening of perovskite phase, perovskite phase can be separated by mineral dressing method.

Jan 1, 2009

By Holger Cordes

X-ray diffraction has long been used for qualitative and quantitative mineral analysis but Rietveld data analysis is still an under utilized method for mineral exploration and processing applications. In this full-profile approach the structural parameters of each mineral phase, together with experimental parameters, are refined by least-squares methods to minimize the difference between observed and calculated diffraction patterns. The result is a standard-less, quantitative analysis of the mineral abundance in the sample that is more accurate and considerably faster compared to traditional methods. The TOPAS software package combines a user-friendly interface with a unique approach to resolve overlapping peaks. Automated analysis options are also available and significantly reduce analysis time for routine samples. Several examples on a wide range of naturally occurring rock types are shown that illustrate the capabilities and limitations of the method. The examples include several options for the quantification of amorphous constituents like volcanic glasses.

Jan 1, 2006

By Viviane Tavares

The liquid crystal display (LCD) are currently known by its vast application in electro ? electronic devices, amongst them can be detached the devices of TV, laptops, electronic date, calculators and even though the mobile telephones (mobiles). The mobiles are changed more frequent of the TV for example, this happens due to the technology advance. With the constantly mobile exchange, the batteries, printed circuit board and liquid crystal display accumulation its become an environmental problem. To minimize the environmental impacts caused by mobile telephones residues are considered the segregation process of the LCDs main components, to goal to recover the recycle material. This process involves the use of treatment ore techniques with disc, hammers and balls mills. The process with best efficiency (about 98%) of LCD glass release was the hammers mill. The glass recovered can be used in the glass recycling and the sand substitution in the production of concrete blocks.

Jan 1, 2009

By J. G. Eacott

This paper reviews the role of oxygen potential and the advances that have been made in the application of tonnage oxygen in copper smelting. Brief reference is made to reaction kinetics before attention is turned to the thermodynamic considerations in copper melting to illustrate the importance of oxygen and. oxygen potential in the component parts of the overall smelting process. The chemical potential diagram for the Cu-Fe-S-O-Si02 system is used to elucidate the difference b etween the conventional matte smelting process and the modern continuous processes. A progressive oxidation scale' is constructed to show the common elements which exist, and the matte grades produced, during the smelting of concentrates to blister copper in commercially available copper smelting processes and those under development. The common route in producing blister copper from molten mattes, regardless of process, is illustrated on the Cu-Fe-S equilibrium phase diagram. The essential features of oxygen enrichment, in terms of its effect on combustion conditions (i.e. oxidation of fuel and sulphide minerals) and the heat balance are outlined. The benefits of oxygen enrichment are listed. The influence of tonnage oxygen and its effect on productivity, fuel savings, gas volume and strength in various copper melting processes are examined as a state-of-the-art review. Reference is made to the economics of tonnage oxygen utilization.

Jan 1, 1983

By Ari I. Kogut

Impurity minerals in fluorspar ores and concentrates from a deposit in Southern Africa have been studied by reflected light, transmitted light, and cathodoluminescence microscopy. The principal impurities are quartz, calcite, aegirine, apatite, ankerite, magnetite, goethite, and synchysite [Ca(La,Ce,Nd)(C03l2Fj. Cathodoluminescence microscopy was found to be very useful in studying the character of the fluorite and especially for recognizing the presence of apatite and calcite impurities. Fluorite exhibits blue, calcite shows yellow, and apatite has white, light purple, and pink cathodoluminescence. The cathodoluminescent character of apatite varies with its geological environment and position in the orebody. The results of this microscopic study show that phosphorus present in flUorite concentrates occurs principally in binary locked apatite-fluorite particles. Successive fluorite cleaner concentrates contain progressively smaller amounts of locked apatite-fluorite particles. Free apatite has been effectively partitioned to the final tailings.

Jan 1, 1995

By N. E. Idenyi

The effects of compositions and firing temperatures on the physico-mechanical properties of blended Nsu fireclay and Nkalaha redbrick clay have been investigated. The clay samples were compounded according to the following ratios: 10:90, 20:80, 30:70, 40:60 50:50, 60:40, 70:30, 80:20 and 90:10 in the order Nsu: Nkalaha respectively, and test samples made and fired at 9000C, 10000C 11000C and 12000C. The properties tested for were the modulus of rupture, porosity, shrinkage, apparent density, water absorption and bulk density. From the results obtained, it is inferred that the blends have a maximum service temperature of 11000C, with the 30: 70 blend presenting the best characteristics. A conclusion is drawn to the effect that the blend could be adapted for the production of ceramic earthenware, electrical porcelain pin insulators, cement manufacture and for refractory linings where temperature requirements are less severe.

Jan 1, 2006

By Michael P. Sudbury

Non-ferrous slags are granulated and stockpiled as an alternative to pit cooling or transporting molten slag to a dump. The chemical composition of such slag is determined by the pyrometallurgical process in which it is produced, while the size distribution is set by safety concerns or a desire to reduce wear of pumps, pipelines and other equipment. Relatively few operations give consideration to the effect of granulation conditions on other properties of the granulate as the material is typically accumulated on the smelter site. It is becoming recognized that slag has many potential commercial uses and carries much of the energy applied to the smelting operation. This paper outlines the findings of extensive work to identify uses for granulated non-ferrous slag, the importance of preparation conditions on the properties, impediments to more extensive use of granulated slag, the real costs of slag stockpiling and the opportunities for further productive research.

Jan 1, 2006