Search Documents

By J. Howarth

Two electrochemical processing methodologies have been used to electrogenerate bromine-laden solutions for gold-leaching purposes. In the first process, a laboratory-scale cell in which the anode and cathode compartments were separated by a cation-exchange membrane was employed. The bromine produced by electrolysis of a 4% bromide solution was used to leach gold from a low-grade ore. The pregnant leach solution was then returned to the cell to recommence the cycle. High current efficiencies (90-93%) were maintained over six cycles. In the second process, an undivided hypochlorite generating cell (Chloropac"') was used to generate bromine from a simulated leach solution. Electrolyses were performed on a pilot-scale (100-150 gallons) with solutions containing different levels of bromide ion. The current efficiencies were also high (80-90%) and unaffected by the bromide concentration (over the range 2.5-5%) provided the electrolysis was run to low conversion « 15%). The Chloropac module was capable of delivering 0.6 kg bromine per hour at a power cost of $0.09 per kg. Using these figures, a detailed economic assessment for a 1000 metric tonnes (MT) per day gold ore processing plant was made. Electrolytic regeneration of bromine in a gold leach/recovery circuit dramatically improves the process economics over cyanidation.

Jan 1, 1991

By Xiaojie Gao, Jingshe Li, Chengsong Liu, Haiyan Tang

In order to clarify the reaction between MnO-SiO2 oxides with low FeO content and Fe-Mn-Si alloy, two diffusion couples were produced by the new method using confocal scanning laser microscopy (CSLM). The interface of the alloy and oxide, content of Mn and Si in the alloy near the interface, size distribution and composition of the particles which precipitated in the alloy were observed and analyzed using the electron probe microanalysis (EPMA). Results show that though the FeO content in the oxides decrease to 1% which is lower than the equilibrium with the molten steel at 1873K, the diffusion of oxygen from oxide to alloy still exists during the heat treatment at 1473K and causes shorter Particle Precipitated Zone (PPZ) and Manganese Depleted Zone (MDZ) normally for the reduction of diffusion flux of oxygen.

Jan 1, 2015

By R. Hurman Eric

The flow of molten slag and matte and the estimation of the mass of settled matte in electric furnaces is discussed and the action of the electric furnace as a settler is considered. Particle size of the concentrate and its grade are major contributors to settler dimensions. Discussion on the production capacity of the electric furnace with reference to operating current, power input, furnace dimensions such as width and length and electrode diameter are given. These discussions are based on considerations derived mainly from experimentally determined properties of the slag such as its resistivity, viscosity and liquidus temperature. Extension of the design and operating considerations to circular furnace symmetry is also discussed.

Jan 1, 1995

By Md. Maniruzzaman

The quenching performance of a liquid quenchant can be controlled by controlling the agitation in the quench tank. Without agitation, a vapor layer or bubbles form at the hot part surface and the natural convention of the quenchant limit the heat extraction rate at the quenched part surface. Resistance to the heat extraction rate can be reduced by breaking the vapor layer or by inducing a turbulent convection at the part surface through agitation (Le. forced circulation of the quenchant). To determine the effects of agitation on the quench performance of a mineral oil based quenchant, the CHTE quench probe system was used with AISI4140 steel probe tip. Quenching performance of the oil is evaluated by computing the effective heat transfer coefficients of the steel probe as a function of surface temperature using Lumped Parameter Analysis. In addition, computational fluid dynamics (CFO) simulation of the quench tank with an impeller type agitator has been done to understand and predict the fluid flow pattern in the tank. CFO simulation also provides insights for determination of optimal location of the impeller and the quench probe tip. Keywords: CHTE Quench Probe, agitation, CFD simulation, liquid quenchant, 4140 steel

Jan 1, 2003

By Donald Voit

"The reaction between zirconia/zircon, coke, and chlorine involves a slow reaction between the coke and the zirconia/zircon and a fast reaction with chlorine. Because of the fast chlorine reaction, the reaction rate for zirconia/zircon is nearly independent of chlorine concentration for most conditions. The reaction between zirconia/zircon and coke is particle size controlled and related to the degree of physical contact between the zirconia/zircon and the coke. Since particle-particle contact is critical, compaction of finely ground coke and zirconia/zircon produces the highest reaction rates. Uncompacted, coarse coke and zirconia/zircon has the slowest reaction behavior with static bed tests.SummaryZirconia reacts with chlorine in the presence of carbon to form zirconium tetrachloride, carbon monoxide, and carbon dioxide. A similar reaction occurs with zirconium silicate with the additional formation of silicon tetrachloride. The reaction rate depends primarily on temperature and the intimacy of contact between the zirconia and the coke. The reaction is multi-stepped with a slow reaction between coke and zirconia to form an intermediate that reacts rapidly with chlorine, causing the order of the reaction for chlorine to be near zero. Chlorination rates in the range of 1 µmole/hr/cm2 are seen for fluid bed reactors. Plug flow, and static bed reactors have reaction rates of the order of 1 mmole/hr/cm2, where the area is based on the zircon surface area in plug flow and fluid bed reactors and the boat cross sectional area in a static bed. Chlorination rates measured in zirconia/coke briquettes are higher with rates as high as 400 mmole/hr/cm2 reported. High chlorine diffusion resistance, not accounted for in the analysis of experimental results, has led to a lot of confusion in the literature interpretation of chlorination data.In general coke and zirconia/zircon particle size, coke and zirconia/zircon intimacy, coke to zirconia/zircon ratio, chlorine concentration, and temperature are important variables for chlorination. Decreasing the coke and zirconia/zircon particle size generally increase the reaction rate. The coke to zirconia/zircon ratio affects the reaction in a more complex way. Increasing the chlorine concentration generally increases the reaction rate, but the effect appears to be more related to the concentration dependency of diffusion than to its role in the kinetics. The reaction rate increases with temperature but the exact behavior is complicated by temperature effects on diffusion."

Jan 1, 2011

By R. Hurman Eric

The electrode in a slag-resistance electric furnace is the central factor in the design and operation of the furnace by its role of conveying the smelting power, i.e. heat needed for the operation. The control parameters are the size and positioning in the slag bath which are defined by slag resistivity, furnace resistance, cell constant and power input sequence all of which are closely interrelated. The flow of heat generated by the electrode current determines the energy distributions and thus the furnace dimensions. Heat flow models concerning vertical, horizontal and combined two-dimensional flows are discussed. All these considerations are based on the experimentally determined slag properties such as its resistivity.

Jan 1, 1995

By Matthew C. Binsfield

The simultaneous electro winning of zinc and manganese from waste water treatment plant sludge was studied as a part of the overall research program, which was conducted to develop the methods for removal of environmentally hazardous metals from the Bunker Hill Superfund Site. This paper discusses the electrolytic method for recovery of zinc and manganese from the solution produced by leaching of sludge with S02 + H2S04. After three stage purification of the leaching solution, zinc and manganese were electro won simultaneously in an undivided electrolytic cell. Zinc was deposited on an aluminum cathode, while manganese was simultaneously produced (as Mn02) on a lead silver anode. The electrowinning parameters studied were the effects of: temperature, current density, electrode material, spacing of electrodes, composition of electrolyte, and electrolyte additives. Anodic and cathodic efficiencies were 30 and 91%, respectively. In light of the process design parameters discussed in the paper, which are affecting the electrowinning, these efficiencies were found as acceptable with regard to the quality and marketability of the products.

Jan 1, 1996

By James A. Voigt

The efficient separation of metal species from aqueous streams by precipitation techniques requires 'a fundamental understanding of the various processes that occur during precipitation. These processes include particle nucleation, particle growth by solute deposition, agglomerate formation, and agglomerate break-up. The application of the population balance approach has been used to develop a kinetic model that accounts for these competing kinetic processes. The usefulness of the model is illustrated through its application to the precipitation of yttrium hydroxynitrate, YHN. The kinetic parameters calculated from the model equations and system-specific solution chemistry are used to describe several aspects of the effect of pH on the precipitation of the YHN. Implications with respect to the simultaneous precipitation of more than one cation type are also discussed through use of example systems: The effects of solution chemistry, precipitator design, and solvent choice are considered.

Jan 1, 1996

By Buket Tunçer, Mehmet Buğdaycı, Onuralp Yücel

ZrB2 and TiB2 are one of the most significant metal borides. They are being used in various industrial areas from space technology to nuclear industry owing to their physical properties such as high melting point, high thermal/electrical conductivity and low density. Present study was conducted in two main stages: Self-propagating high-temperature synthesis (SHS) reactions and leaching. ZrO2, TiO2, B2O3 were used as starting material and Mg used as a reductant to produce ZrB2-TiB2 powders via SHS. Therefore, it was aimed to determine production parameters, leaching conditions and comprehensive examination of final product features. The samples were characterized by using chemical analysis (AAS), XRD, XRF and SEM/EDS techniques

Jan 1, 2015

By Gopalakrishna B. Prabhu, David L. Bourell

"Three mol% Yttria-Stabilized Tetragonal Zirconia (YSTZ) was prepared by a sol-gel synthesis technique using zirconium tetrachloride and hydrated yttrium chloride precursors. After drying and annealing at 823K, the particle size was in the range 10 to 20 nm. The zirconia powder was sintered using a uniaxial hot press at an applied stress of 20 to 40 MPa. One hour, isothermal sintering was performed in air after initial heating at 50K/min. Theoretical density was obtained at densification temperatures above 1498K. After sintering, grain coarsening characteristics were studied using constant heating rate anneals followed by quenching, based on a model for grain coarsening in a linear heating rate cycle. The microstructural change was studied using SEM and TEM and the phases were determined using x-ray diffraction.IntroductionThe ability to sinter nanocrystalline materials to full density several hundred degrees below the normal sintering temperatures is one reason for their current interest. [1-5] Yttria Stabilized Tetragonal Zirconia (YSTZ) of grain size of about 300 nm has exhibited superplasticity, with elongations as large as 800%.[6-7] Fine grain size is critical for superplasticity. Retention of the fine grain size during sintering of nanocrystalline powder is important if a material is to exhibit superplasticity or to exhibit physical or mechanical properties associated with the ultra fine structure. This paper investigates the sintering behavior and the grain coarsening characteristics ofnanocrystalline YSTZ.Techniques for synthesizing nanocrystalline materials have been studied in great detail earlier. [8-12] The techniques used to synthesize nanocrystalline zirconia include alkoxide synthesis [9], the chloride method [11], the peroxide method [13] and the acetone-toluene method. [13] In this paper the method used in the synthesis of zirconia is the chloride technique. With this precipitation technique, either zirconium chloride or oxychloride and a corresponding yttrium salt or even pure yttria are used."

Jan 1, 1994

By Ricardo Melamed

Metallic mercury has been extensively used for gold recovery. Although the solubility and mobility of metallic mercury is low, this metal can undergo many transformations, leading to mercury contamination in humans. The complexity of Hg chemistry in the environment reflects its different possible oxidation states and species, with different physical-chemical properties. The interaction of Hg in the terrestrial system, as well as in the aquatic environment, is important to understand the mercury cycle. This paper reports data on the adsorption of Hg onto an Oxisol soil. Results show that the interaction of Hg(II) at the soil-solution interface depends strongly on ligand concentration in solution, which can affect Hg mobility. The presence of the chloride anion in solution increases the mobility of Hg(II) through the soil, due to a relative lower affmity of mercury chloride at the oxide surface. In the absence of chloride, Hg(II) form strong complexes with the surface, and its adsorption behaviour is similar to the adsorption of other hydrolizable cations.

Jan 1, 1996

By Xiyun Yang, Hui Xu, Xichang Shi, Xiang Xiao

"Rod-like magnetite particles were prepared by precipitation of iron salts with urea under the induction of magnetic field. Temperature and initial Fe3+/Fe2+ ratio have a significant effect on the composition of the product. Magnetite particles change from spherical into rod shape in the presence of a 0.35 T magnetic field, The addition of a small amount of spherical seeds increases the rod-like magnetite particles yield. The seeds are prepared by aging ferrous and ferric solution with sodium hydroxide as precipitator. The aspect ratio of the rod is controlled by varying the volume ratio of seed to iron salt.IntroductionMagnetite, an important member of magnetic materials, has attracted a lot of attentions for its super magnetic properties. The rod-like magnetite particles have high anisotropy and coercive force as well as super magnetic properties compared to other shapes, and are widely used as high magnetic density media, magnetic devices and microwave materials [1-4]. Recent studies have found that magnetic field can direct magnetite growing along easy magnetization axis to get one-dimension particles [5-6]. Chen et al. [7] synthesized single crystalline nanorod magnetite under magnetic field. Wang et al. [8] discovered that magnetite grew along easy-magnetization directions under 0.35T magnetic field. Vereda et al. [9-1 O] found that magnetic field had a dramatic effect on the morphology, inducing the aggregates to line along one direction to form rodlike particles.At present, most of the synthesis methods reported in the literature result in a low yield of rod particles and the aspect ratio are difficult to control. Recently, we developed a seed-mediated growth approach to making rod-like particles in an aqueous solution. The spherical magnetite generated by oxidation serves as a seed. These seeds are then added to a solution containing iron salt and urea, and provide nucleation sites for magnetite rod growth."

Jan 1, 2011

By H. Kaffash

Ferromanganese is a ferroalloy with high manganese content which finds many uses for example as deoxidizer in steelmaking industry. However, there is very little data on the dissolution rate of carbonaceous materials in Mn containing metals. In this paper, the kinetic analysis of carburization reactions is investigated for Mn–Fe alloys. Dissolution rate of graphite in pure iron and four different alloys with 10 wt%, 40 wt%, 60 wt% and 85 wt% manganese at 1823 K was studied. Results showed that the dissolution rate of carbon from graphite increased with increasing time for all alloys. The dissolution rate constant increased with the increasing manganese content from 6.5 × 10−3 cm/s for 0%Mn to 23.6 × 10−3 cm/s for 85%Mn.

By Jintao Gao, Zhancheng Guo, Chong Li

A new approach to enrich MFe and RO phase from the converter slag by super gravity was investigated. The samples obtained by the gravity coefficient G=600 and cooling rate V=5K/min from 1623K to 1373K appeared significant stratification and the MFe gathered at the bottom of sample. With the help of metallographic microscopy and X-ray diffraction, it is found that large quantity of white RO phase gathered at the lower part of the sample as the concentrate, with volume fraction appearing gradient distribution along the direction of super gravity, while the upper part was mainly composed of dicalcium silicate as the tailing. The mass fractions of the FeO, MgO and MnO in the concentrate are up to 40.46%, 6.9% and 3.91%, while that in the tailing are just 11.65%, 2.15% and 1.55%. The recovery ratios of FeO, MgO and MnO in the concentrate are 60.35%, 58.45% and 72.24%, respectively.

Jan 1, 2016

By S. Yin, A. Bogno, H. Henein, P. Natzke

Impulse Atomization (IA) (a single fluid atomization technique) was used to rapidly solidify Al- 4.5wt%Cu and Al-4.5wt%Cu-0.4wt%Sc under argon atmosphere. In addition to the IA-generated droplets, the same technique was used to produce strips by Spray Deposition (SD) of the same alloys on a copper substrate with and without oil coating. The rapid solidification microstructures were analyzed using Scanning Electron Microscopy (SEM). From the SEM images, the amount of eutectic and the secondary dendrite arm spacing (SDAS) were measured. These SDAS results lead to the estimation of cooling rate. The eutectic fraction coupled with the metastable extension of the solidus and liquidus lines of Al-Cu (Sc) phase diagram lead to the estimation of primary and eutectic undercoolings. A comparison of the solidification path of the droplets and the strips was done as well as the analysis of the effects of scandium.

Jan 1, 2015

By Xu Zhang, Xuewei Lv, Guibao Qiu

Slag foaming phenomenon is of vital importance to the mass and energy transfer in metallurgical processes. A considerable extensively studies carried out via out-gas in the past cannot simulate well the foaming phenomenon formed in the blast furnace where high TiO2 iron ore is used. A gas reaction was designed in the water-glycerol system to simulate the inner-gas system. This study investigated the influences of solution viscosity, particle concentration and particle size on foaming caused by endogenetic gas. The results show that the foaming height decreases with the increase of solution viscosity, which means reduced foaming ability, more difficult foaming elimination process and prolonged time for natural defoaming. With increasing the solid particle content, the foam height presents a trend which increases firstly and then decreases. Under a certain solid particle content, foaming height decreases with the increase of solid particle size, indicating a weak foaming ability.

Jan 1, 2015

By Lauri E. K. Holappa

Ferrochrome, as the central constituent in stainless steels is one of the most rapidly growing primary metallic products. In this contribution results of a comprehensive study on the reduction process of chromite ore to FeCr are presented including thermodynamic examination, experimental work on kinetics and mechanisms in solid state, and smelting reduction conditions as well as kinetic modelling of solid state reduction.

Jan 1, 1999

By William Petrul

Image analysis studies were performed on mill products from laboratory flotation tests of the Zn-Pb ore from the Faro deposit in Yukon, Canada, to determine mineral liberations at specific grinds and to predict recoveries at optimum flotation conditions. The minimum and optimum grinds for liberating sphalerite and galena were predicted from size analysis data for the minerals in large ore pieces, and determined by image analysis studies of the mill products. The determined optimum grinds are about 2 Tyler mesh sizes larger than predicted because sane of the fine grained sphalerite and galena occurs in interstices between coarser grained pyrite and is liberated when the pyrite grains are broken apart. Materials balance calculations were performed on the analyzed values for the liberated and unliberated sphalerite and galenaa to determine their distributions in the mill products. The laboratory flotation tests recovered 74% of the sphalerite and 83% of the galena in Zn and Pb concentrates respectively. The mineral evaluation study indicates that the optimum recovery for sphalerite and galena are 85 and 83% respectively. The company is currently recovering 80% 'of the sphalerite and 82% of the galena.

Jan 1, 1989

By R. F. Hammen

Heavy metal contamination of water is a problem of immense national and international proportions. However, effective cleanup is complicated both by the toxicity and the low concentrations of metals in wastewater streams. Using high performance chelation chromatography, the solid phase extraction and purification of extremely dilute metals from water was highly effective. The process is based on selective displacement of metals from a chromatographic column containing a chelating resin. The resin is characterized by extremely efficient adsorption kinetics which allow rapid and complete removal of the metals.

Jan 1, 1993

By M. B. Mesina

Mechanical separation systems are widely used nowadays for scrap metal processing, but they have natural limitations in product quality. The quality of the final product is considerably improved when sensors are used in the separation process. This paper describes new methods using sensors for scrap metal sorting and quality control. An example is the electromagnetic sensor, which uses the electrical and magnetic properties of materials to distinguish between different non-ferrous metals. The measurement results of two prototypes are reported. The benefits and the possibility to integrate such systems into practical applications regarding the processing of secondary raw materials are also described.

Jan 1, 2003