Search Documents

By Barbara C. Schickner

The long-awaited COSMAR study prepared under the auspices of the National Academy of Science reaches one emphatic conclusion that has been enthusiastically seconded by the mining industry: The 1977 federal surface mining act is "poorly suited" as a vehicle to regulate noncoal mining. Though the industry greeted the report with approval, the weight it will carry and the extent of its impact are yet to be felt. The COSMAR report makes no recommendations-that's a job left to the Administration's Council on Environmental Quality-and the prospect of legislation still hovers. For a closer look at the study, MINING ENGINEERING talked to COSMAR committee chairman James Boyd, a well-known presence in the mining arena for over 50 years. After highlighting some of the study's major points, Dr. Boyd comments on the report's impact and possible repercussions. Dr. Boyd, for those readers who haven't seen the COSMAR report, would you summarize some of its major findings? The committee analyzed the surface mining act to determine if it was applicable to noncoal mining and found that there were provisions of the act that either could not be met by existing technology or would be extremely difficult and not necessarily beneficial to adapt. We found that most noncoal mineral mines, despite their obvious diversity, can be considered in two major groups: 93% of all mines move 45% of all materials mined (mostly small units mining construction materials); and the few gigantic regional operations (2%)-copper, iron, phosphate, and uranium mines-that move 50% of the material. With few exceptions, neither of the two groups is amenable to the coal mining practices addressed by the act. The strip mine law was designed for coal mining, where land is regraded, revegetated, and returned to usefulness. In contrast, construction mineral quarries supply local needs for decades, remove most of the material from the immediate vicinity, and cannot be returned to their premining uses (though they have innumerable other valuable uses). The nation's huge mineral deposits require enormous capital investments, are vital to the nation's economy, and can take centuries to exploit. Any attempt to return these locations to premining use would be illogical. Pebble phosphate in Florida and red-bed copper in Oklahoma come near to meeting the conditions contemplated in the act. In addition to COSMAR's basic finding, the study also makes the following points: •Mining uses a relatively small part of the land resource, in contrast to

Jan 4, 1980

By Rolando Gonzalez

Mexico’s role in the world economic community continues to grow. And it is important that the country makes use of its natural wealth, including its large underground deposits of minerals and metals. With that in mind, Industrias Peñoles S.A. de C.V.(Peñoles), a mining, smelting and refining company, began mining lead, zinc and other metals from the Francisco I. Madero Project (FIM). The mine is located about 600 km (370 miles) northwest of Mexico City in the state of Zacatecas. Peñoles plans to remove about 3 Mt/a (3.3 million stpy) of ore from FIM. To achieve this goal, the company needs to optimize its processing, to maximize the amount of metal it extracts through FIM’s large flotation lead-zinc concentrator. To ensure high productivity, Peñoles and its contract engineering firm, M3 Engineering and Technology, of Tucson, AZ, have implemented anore processing system.

Jan 1, 2003

By G. Karahalios

Industrial minerals have always enjoyed an important share in the technological growth of any country in the world. Today, extraction and trading of industrial minerals has expanded, but is also subject to stricter environmental guidelines. This paper presents the current status as well as the growth potential in the exploitation of industrial minerals in the countries of the south eastern European region, i.e. Albania, Bosnia-Herzegovina, Bulgaria, Croatia, F.Y.R.O.M., Greece, Italy, Serbia and Montenegro, Slovenia and Turkey. More specifically, annual production figures per country are presented for1992-1998. These figures are compared to each other and, where applicable, to world production figures. Trading of industrial minerals from these countries to Europe and the world and its effect to the local economies is also evaluated were such data is available.

Jan 1, 2000

By J. Sandford, S. Hennings

EXECUTIVE SUMMARY An approach borrowed from the petroleum industry was applied to the gas development evaluation for the Bulga underground coal mine in New South Wales, Australia. The results enabled the coal mine operator, Xstrata Coal, to systematically plan the extraction of gas in harmony with mine production planning of multiple coal seams. This has allowed for a more proactive approach in preparing the resources and infrastructure needed to capture the gas and accelerate coal mining while maintaining their high level of commitment to safety. Norwest has for decades used gas recovery simulation models to assist the petroleum industry and the coal bed methane (CBM) industry in understanding and forecasting fluid saturations and flow behavior. Norwest developed a similar process with Xstrata to migrate existing mine data at Bulga into reservoir simulation models to study various drainage alternatives. An interesting feature to the evaluation was also developing an understanding of test procedures and nomenclature from the mining industry to properly translate the data for input in simulators developed for the petroleum and CBM industries. The model was then calibrated to actual field data collected from drainage pilot tests that Norwest helped design and monitor at Bulga. The resulting calibrated predictions were then used to develop budgets, schedules, resource requirements, and alternatives for capturing the gas and delivering it to market ahead of mining. Increasing revenue, reducing emissions, improving schedules and cutting costs for the mining operations have all contributed to justifying this advanced approach at Bulga. It has also allowed Xstrata to expand their focus to the sizable gas reserves in seams not currently planned for mining. Several of these seams would be economic gas development targets once the gas recovery infrastructure is installed for the mine. The evaluation process was refined throughout this project and the resulting approach will benefit Xstrata with their broader strategic development of resources in the Hunter Valley and beyond to their worldwide operations.

Jan 1, 2007

By John E. Tilton

The ability of companies and countries to mine copper and other mineral commodities competitively and in the process to generate new wealth depends on their mineral endowment. Chile, for example, produces and exports copper because it is well endowed with high-quality, low-cost deposits. This production creates wealth that benefits mining companies and their stockholders, the government, local communities, as well as copper consumers around the world. The widespread perception that mineral endowment must largely determine competitiveness, or what economists call comparative advantage, must be true at any particularly moment. Countries with abundant reserves must be competitive. This follows from the definition of reserves — the quantity of a mineral commodity found in discovered deposits that are profitable to exploit under current conditions. As a result, it is a tautology and not particularly interesting. The important question is what causes reserves to change over time, producing in the process new wealth and shifts in competitiveness?

Jan 1, 2003

By M. M. Poulton

Universities are not immune from the large number of retirements facing the mining industry. Department heads anticipate that we will need to replace all of the senior mining engineering faculty in the U.S. by 2020. Long term studies of Ph.D. completion times and success rates indicate that in Engineering disciplines in the U.S., the ten year completion rate is 65% at best and the four year completion rate is less than 8%. We do not have accurate data on completion rates and times for mining or metallurgical engineering Ph.D. students in the U.S. but students self-report their expected completion times are around 4 years. National data on doctoral students indicate that younger, full time students with sufficient financial support have a higher probability of success in completing their degrees in a timely manner. Students in Eastern U.S. mining engineering programs are on average 32 years old, 85% are full time, and the gap between support and cost of attendance is $5,000 per year. Students in Western U.S. programs are on average 38 years old, 78% are full time, and the financial gap is $8,483. Further, it appears that domestic graduate students are not very geographically mobile. The current demand for new faculty is higher in Western programs but the longer term retirements are higher in Eastern programs. While all Ph.D. students who responded to the 2010 survey indicated an interest in a faculty position at some point in their careers, very few were applying for the open positions. Over the past 35 years for which data could be obtained, the maximum number of Ph.D. students enrolled in mining engineering in the U.S. is 115 with a maximum of 27 degrees granted in one year. On average 89 students are enrolled in doctoral programs in mining engineering in the U.S. with average degree production of 15 Ph.D.s per year.

Jan 1, 2012

By Sakai Kunito, Nigel B. Sugden

If an Earth Pressure Balance (EPB) TBM is operated effectively tunneling can be carried out producing negligible ground movements. Using the methods given in this paper face losses of the order of 0.5% and less are generally obtainable using an EPB. Operating the EPB TBM in this manner reduces the requirement for the building protection measures used to protect surface structures. This can result in a considerable cost saving for the construction of a tunnel under built up areas. This paper to give guidance on the causes of ground movements around a TBM and the methods of running an EPB TBM that will minimize those movements. Details of how this was successfully done during the construction of the Bangkok Metro are given. The paper is split into three parts as below. 1.Causes of ground movements due to TBM tunneling 2.Methods of controlling those movements using an EPB TBM 3.Case history Bangkok Metro (water main)

Jan 1, 2001

By Kazem Oraee

In underground coal mining, particularly room-and-pillar methods, the coal pillars play a significant role in roof stability. If the pillar dimensions are increased, the pillar bearing capacity also increases, but more coal remains in the pillar and therefore the recovery of mining operation decreases. Therefore, determining the optimum pillar dimension based on technical, economical and performance parameters is important. In this paper, the coal pillar is designed by using the concept of ground reaction curve (GRC). For this purpose, the GRC for coal pillars is drawn and then the elastic and plastic zone of coal pillar behavior is determined. Based on elastic and plastic zone, different equations are presented to draw a pillar reaction curve and the process of coal pillar design based on GRC is explained. As a case study, this new technique is applied to study the coal pillar state in Tabas coal mine of Iran. The results show that the presented new approach is successfully used in the design of the optimum coal pillar dimensions, and also determines the elastic and plastic behavior limit, which is important especially for the logical design of yield pillars.

Jan 1, 2009

By Allison

During the 1980’s, laboratories opened throughout the United States to serve the analysis needs of a rapidly growing asbestos abatement industry. The samples analyzed were either collected during the abatement of known asbestos-containing materials or were suspect asbestos-containing construction materials. Many asbestos analysts received minimal training and used analytical protocols that were industry specific. False positives (reporting a sample as containing asbestos when none is present) went unnoticed or had minor repercussions. The mindset of the industry was to err on the conservative side – it would be better to identify a non-asbestos fiber as asbestos than visa versa. With growing public awareness of the health hazards of asbestos, other materials began to be tested for asbestos content. Rock and ores began to be tested for naturally occurring asbestos by these laboratories using the same protocols or an in-house protocol. Analysts were given no additional training and accreditation, in most cases, it was not required. With no consistency in sample collection, testing protocol or expertise in analysis, significant discrepancies in final results can be expected. If we further complicate this scenario with misidentification of naturally occurring look-a-likes for asbestos, expensive false positives are likely. To avoid the repercussions of misidentification of naturally occurring chrysotile asbestos from look-a-like fibers in rock and ores, correct sampling and analysis protocols with more stringent scientific diagnostic criteria are needed.

Jan 1, 2005

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

e Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

By Carmel Bofinger, Maureen E. Hassall, David Cliff, Eric Stemn

e Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.

By Todd Wanless

This paper addresses the challenges experienced by the designer and three government agencies during implementation of major improvements for the Turkey Creek Tunnel in Kansas City, Kansas. The tunnel serves as a vital stormwater conveyance system for upstream flood control. Major structural deficiencies were identified within the tunnel including complete loss of sidewall and invert. Without immediate attention, complete loss of the tunnel arch could lead to blockage and extensive remedial repairs under difficult conditions. Considering that tunnel flows must be maintained during construction, a phased design and construction process has been implemented to expedite stabilization of the erosion cavities followed by tunnel liner repairs.

Jan 1, 2008

By Rex E. Loesby

The marble deposits of Yule Creek were first discovered in the late1870s. Minor quarrying occurred between that discovery and the early 1900s. Major development occurred in 1905, when Channing Meek, with some help from the Rockefellers, raised $3 million to develop the Colorado Yule Marble Quarry. That is $50 million in today’s dollars. Some of the words used to describe the marble deposit were “gigantic, remarkable, flawless and immense.” Boosters proclaimed, “The marble age is here.” Obviously, dreams were big for Marble.

Jan 1, 2003

By Richard E. Gray

The Office of Surface Mining Reclamation and Enforcement (OSM) is preparing an Abandoned Mined Lands Reclamation Control Technology Hand- book. (l) GAI Consultants, Inc. , recently prepared Chapter 2 on Mine Subsidence Control which contains a summary of subsidence abatement measures plus two new decision matrices for evaluating the subsidence abatement options that might be considered for a particular problem. These decision matrices are presented for information. Review of the subsidence abatement methods resulted in identification of items where research may impact the current state of technology in mine subsidence control. These research needs are presented to stimulate discussion of their importance in subsidence abatement and to encourage funding agencies, researchers, and practitioners to work on them.

Jan 1, 1982

In bump-prone coal mines, roof and rib support is subject to dynamic as well as static loading. Although less frequently encountered, the dynamic loading component can result in violent coal expulsions into openings seriously threatening the safety of workers. Dynamic support systems that have been increasingly implemented in many deep hard rock mines for dynamic failure containment have not yet found their adaptation to deep coal mines at desired levels. This paper examines the potential use of some of these dynamic support systems in deep coal mining, particularly in the western United States. Fundamental principles of dynamic loading are reviewed in the context of their application to dynamic failure mechanisms in coal mines. Potential benefits and applicability of the suitable hard rock dynamic support systems are discussed in relation to coal bump mitigation. The resulting insight provides a starting point for development of dynamic support elements for bump prone conditions in deep coal mines.

Jan 1, 2009

Two miners were fatally injured when a pillar bump occurred during retreat mining in a southern West Virginia coal mine. The mine was operating in the Eagle seam with overmining in the No. 2 Gas and Powellton seams. A coal bump is defined as a sudden and violent failure of coal caused by the release of stored strain energy in the pillar. While significant strides have been made by academia, industry, and regulatory agencies to better understand bump conditions and mitigation techniques, coal bumps represent a long standing, highly site-specific engineering problem in which the exact failure mechanism(s) is not clearly understood.

Jan 7, 2020

By R. Curtis

To achieve compliance with 2015 EPA Tier 4 Final regulations, which permit only around 10% of Tier 3 particulate matter (PM) and NOx emissions, a number of technologies are being implemented. Use of a fuel borne nanoparticle combustion catalyst reduces the level of PM and unburned hydrocarbons exiting the combustion chamber, alleviating the burden on downstream exhaust after-treatment systems. The impact of an iron-ceria combustion catalyst (GO2) on carbon oxidation kinetics and on diesel engine emissions is presented. The iron-ceria nanoparticles catalyze carbon oxidation at lower temperatures and increase the oxidation rate by a factor of 18 at 400 °C. Engine tests on a generator powered by a John Deere Model engine and field tests on a Cummins ISC 330 tractor truck and CAT 3508B propulsion engines are presented. Use of GO2 resulted in a reduction in PM10 (particulate matter under 10 um) emissions of up to 26% and a hydrocarbon emission reduction of up to 41%. NOx emissions did not increase in these trials and the amount of change depended on engine type. Application of this fuel borne technology for emissions reductions in mining equipment offers significant benefits.

Feb 27, 2013

By Tom Ireland, Tony Rock

The proposed 1.83km long twin bore A3 Hindhead road tunnel planned for contruction in 2008 is being delivered under a Highways Agency Early Contractor Involvement (ECI) contract. The proposed construction methodology is progressive mechanical excavation of a horseshoe shaped tunnel with shotcrete installed close behind the face using robotic spraying equipment. The tunneling medium is a ‘soft rock’ sandstone for which there was little previous tunneling experience, requiring extensive geotechnical investigations and an innovative approach to lining design. A 240m long portal section though sandy material utilising a steel pipe umbrella is also required. This paper describes the development of the tunnel planning and design including the most recent developments in UK road tunnels, and the innovation included in the ‘permanent’ primary lining design.

Jan 1, 2007

By Don W. Deere

Faults under high rock cover represent some of the most severe ground conditions a Tunneler can encounter. High ground water pressures and flows are usually associated with mountain faults. Ground behavior can range from blocky ground to flowing sands and squeezing clays. Sticking a IBM within a fault zone for many weeks, with the disastrous financial consequences, is still a common occurrence. Interpreting the geology and detecting the location of a fault prior to penetrating it is a fundamental step to successful tunneling. Ground water control through predraining or pre-grouting is the second fundamental step. This paper discusses techniques applied for detecting and crossing mountainous fault zones through the use of case histories across the globe.

Jan 1, 2007

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

Jan 1, 2007