Search Documents

By Glenn E. Craig

The practical and effective pulp distributor here presented is believed to be of a completely new and innovative design. It was developed at the San Nicolas Plant of the Marcona Mining Company in Peru, where it has been thoroughly plant tested using iron ore slurries of a particularly abrasive nature. It has proven to be superior to the apparatus originally installed, or to any observed in operation elsewhere. In plant practice the capacity and efficiency of many process units such as screens, magnetic separators, and jigs are strongly affected by the loading pattern, and for better results the flow of pulp must be proportioned across the receiving lip in equal quantities per unit width. The distributors originally installed on the drum magnetic separators in San Nicolas proved to be unsatisfactory, and several trial modifications failed to show any improvement. As is usually the case, feed rates were being steadily increased, and appreciable losses to tailings resulted. A check of the distributors on the market discloses no reasonable substitute, so efforts were directed toward devising an entirely new type. Required was a positive type of action which would guarantee that the pulp flow be spread equally along the length of the drum. Discussion As indicated, the motivation for development was simple necessity. The plant in San Nicolas crushes, grinds, and concentrates magnetic iron ores of a particularly abrasive nature, and depends largely on magnetic separation to obtain a marketable product. Feed to the numerous drum magnetic cobbers and finishers varies from rod mill discharge at a nominal minus ten mesh to a ball mill fine grind of seventy percent minus three hundred and twenty-five mesh. Operational factors affecting the magnetic separators were well controlled,

Jan 1, 1971

By George M. Meisel

This paper is devoted to a discussion of the factors governing design of concentrators for large grinding circuits. Emphasis is placed on the manner in which use of ever larger grinding mills has affected the size of grinding bays, service cranes, gear reducers and electric motors, and the selection of ancillary equipment for cushioning of the starting load of large mills. Information is presented on the effect of using large grinding mills on the capital and operating costs of concentrators, e. g. : (Fig. 1) ? Benefits in lower cost of mills, drives and materials handling equipment, plant space, power, grinding media, operating labor and maintenance, and in ease of instrumentation and automation. ? Penalties in distribution of materials from the grinding mills to multiple lines of equipment which have not been developed to commensurately large sizes, and higher cost of ancillary equipment.

Jan 1, 1968

By G. M. Smith

Several significant past and present producers of high grade and bulk tonnage gold ore from southeastern California and southwestern Arizona can be empirically and genetically linked to regional peraluminous magmatism which occurred during the late Cretaceous and early Tertiary. Geological relationships and geochemical characteristics from the Fortuna Mine area will be described and compared to those of the Tumco Mines area. Each of these historical gold producers is viewed as a morphologic end member in otherwise genetically linked metallogeny. Cold-quartz veins at Fortuna can be directly linked to peraluminous pegmatites both physically and mineralogically. Silica-magnetite±spidote±garnet rock which occurs as relatively barren, discontinuous, foliation- parallel horizons at Fortuna, but as high grade gold ore at Tumco, is interpreted as replacement of calcareous units during the same episode of peraluminous magnatism responsible for the gold vein mineralization. Whole rock and trace element data from pagmatites and aplites of the Fortuna and Tumco areas, together with data from the Gunnery Range batholith of southwestern Arizona, indicate that the magma series (after Keith, 1984) responsible for the gold metallogeny is peraluminous calcic, and is quite rich in sodium.

Jan 1, 1987

By C. P. Miller

In a study of the usefulness of geochemical and biogeochemical prospecting for nickel made about two years ago, approximately ten localities, representing several different types of nickel occurrences were sample, and about 1500 samples of plant and soil were collected. This report will briefly cover the data and results for two areas, and s summary of guides for prospecting.

Jan 1, 1959

By H. Y. Yang, L. L. Tong

Semicontinuous-flow, multistage biooxidation experiments of a Chinese refractory, high-sulfur gold concentrate were conducted with different pulp densities for gold recovery. The maximum iron, sulfur and arsenic oxidation rates of 90.0, 88.8 and 96.4 percent, respectively, were obtained in the experiments with 5 percent pulp density. The highest gold and silver recoveries of 96.1 and 68.9 percent, respectively, were achieved by cyanidation. The negative effect of high pulp density on biooxidation was related to the decrease of free and adsorbed cell concentrations with increasing pulp density. The data of iron oxidation from the semicontinuous biooxidation experiments were best fitted by a shrinking core model in which the chemical reaction controlled the rate. The dissolution kinetics of sulfur and arsenic were therefore analyzed by a shrinking core model in which the internal diffusion controlled the bioleaching rates. For the quantitative description of biooxidation efficiency, two parameters — mass dissolution rate and volume dissolution rate — were proposed. In the first stage, the mass dissolution rates of minerals were negatively correlated while the volume dissolution rates were positively correlated with the actual pulp density. The iron and sulfur mass dissolution rates decreased with increasing actual pulp densities in the third and fourth stage, while linear increasing relationships between the volume dissolution rates of minerals and the actual pulp density were observed from the second to fourth stage. The highest mass dissolution rates of minerals were obtained in the first stage with 5 percent pulp density. The highest volume dissolution rates of minerals were obtained in the first stage with 15 percent pulp density. Compared to the volume dissolution rate, the mass dissolution rate was more intuitive to reflect the negative effect of high pulp density on biooxidation efficiency.

By R. M. Damodaran

The flotation performance of Florida phosphate rock was evaluated in terms of the mixing behavior of reagents with particulates during anionic conditioning of phosphate slurries. The various conditioning variables that influence mixing, namely, solids loading, agitation speed and the conditioning time were investigated to determine their effect on reagent coating on the particles. The phosphate recovery was used to monitor the conditioning efficiency. The mixing characteristics of the phosphate feed were evaluated in terms of the ratio of the mixing power P, to the minimum power Pm' required to keep the slurry in suspension. It was found that mixing conditions govern the conditioning time required to obtain high recovery. Reagentization was slower at lower P /P m ratios. At higher P /P m ratios, the flotation recovery was optimized and the agitation speed was found to have no significant effect on it. Optimum mixing conditions were obtained for a 74 wt% slurry at an agitation speed of 450 (47 rad/s) rpm. Under the optimum conditions of mixing, recovery was improved at low collector dosages and short conditioning times.

Jan 1, 1995

By Manuel R. Lastra

Critical to successful dump and heap leaching for gold, silver, copper and uranium are factors such as permeability, solution delivery to the ore, and solution recovery. This paper deals with possible techniques for successful accomplishment of these three factors. New developments as well as older techniques are discussed, together with rationale for use of some techniques in reference to others. The authors hope to present a checklist so that the ideal application to individual mine situations can be achieved. This involves a discussion of the merits of each different method and the situations for most logical application. It is hoped that such discussion will broaden the geographic areas where dump and heap leaching can be applied to include greater winter cold and tropical regions of large amounts of rainfall.

Jan 1, 1984

By Geo. A. Wells

Abstract The consumption of barytes in certain paints polyurethane foams, seamless, flooring, glass, brake linings, plastisol caskets for food containers and in fluids used for gastrointestinal X-ray examinations rely on tie unique properties of barium sulfate, There are no readily available mineral substitutes. Barytes are also the essential raw material for the manufacture of industrially important barium chemicals. High quality barite ore has become scarce throughout the world. Processing ore into quality end products is both capital and energy intensive. These factors have tended to limit availability and increase prices which have encouraged the use of alternates and restricted market growth.

Jan 1, 1980

By E. B. Kroeger

Spoil instability has been a problem at a coal mine in interior Alaska. Parameters such as original site topography, groundwater conditions, material properties, spoil-pile geometry, geology, permafrost, natural slope instability, changing weather conditions, and dense, near-surface vegetation have interacted to produce unstable slopes. Several failure modes have been identified including deep seated earth block slides, bimodal earth flows, and solifluction. Thawing of permafrost also created conditions where sliding of spoil along the interface separating the spoil and the natural ground surface occurred when the cohesion and the friction angle of that zone was reduced to zero and below 15?respectively.

Jan 1, 1992

By Rameshwar Sah, L. R. Singh, SIVALINGARAJU BARISETTY, SHYAM YADAV, P. K. Ghorui

Fly ash is a by-product generated from combustion of coal in thermal power plant. Disposal of fly ash is a major environmental concern for the power plants. Though a considerable part of fly ash is used in cement making and brick manufacturing, substantial quantity remains unutilized. Silica and alumina are the major constituents in fly ash along with lime. Aluminosilicates and unhydrated lime present in fly ash, in presence of water, undergo a pozzolanic reaction and form cementitious bond which holds the particles together. Bentonite is commonly used as binder in micropelletization of process waste to attain the mechanical strength required for handling and transportation. The bonding of particles by bentonite is a physical mechanism, while fly ash bonding is a chemical mechanism. The present paper deals with the partial replacement of bentonite with fly ash in micropelletization without affecting the quality of micropellets.

Jul 30, 2021

By E. Martinez

A heavy mineral sand sample was tested containing 13% heavy mineral consisting of rutile, zircon, and ilmenite. Eleven tests were run at a mill site with a Mineral Deposit Limited MG 4 spiral to determine the effect of the addition 0; magnets to the spiral compared to conventional gravity separation. Different magnet configurations and field strengths were tested. Optimum results were obtained with the spiral retrofitted with magnets. The heavy mineral content of the concentrate was increased from 55.5% in the control to 64.2% with the magnets. The 8.7% improvement in heavy mineral recovery was due not only to the weakly-magnetic ilmenite, but also to increased recoveries if the non-magnetic zircon and rutile. The increased recoveries were achieved with no loss of concentrate grade.

Jan 1, 1992

By Hans Adden, Anne Lehan, Markus Thewes

"1. INTRODUCTION AND MOTIVATION Traditionally design processes are focussed at creating new tunnels for lowest building cost. But the trend towards sustainable constructions in tunnelling has greatly increased in recent years. A critical subtask of this approach is to realize the potential for optimizing and reducing the life-cycle costs (LCC) of tunnels and their components. To evaluate underground infrastructure projects from an economic point of view is therefore a highly topical subject of public authorities as well as private companies participating in Public Private Partnerships (PPP) projects. Nowadays, in the case of public works contracts, the contracting authorities shall draw up rules not only for the design but also for life-cycle costing. Within the scope of the decision-making process of building a new tunnel, planning the maintenance activities or the refurbishment of a tunnel in operation, the decision-makers need detailed knowledge about the current and future financial conditions of the planned projects and selected sub-measures. But in practice, the initial costs still represent the primary decision criterion in the planning phase, whereas the subsequent or follow-up costs, respectively, are only estimated roughly. Although tunnels are the key components and the most costly parts of the transport infrastructure, only a small number of scientific papers deal explicitly with the calculation of life-cycle costs for underground infrastructure. And in these cases, most authors use as the starting point only the basic form of the Net Present Value method which is known as the frequently applied life-cycle costing technique in building construction. The present study explains the strategic concept of life-cycle costing and its fundamental instruments for operational implementation. It shows the necessity to take into consideration that there are fundamental methodical problems when the life-cycle concept is transposed without modifications from building construction to civil engineering. The paper will discuss in detail some selected associated problems with the net present value method. On the basis of operational and safety related tunnel equipment it is shown, what impact this may have on principle determining the LCC of tunnels. Selected best-practices of maintenance planning for tunnels undertaken by the German Ministry of Transport fill the theoretical approach of the concept with life and give a practical orientation. In particular government authorities but also construction companies are interested parties in modern cost management considerations. The reason for this development is the replacement of aged excisting structures and the advancement of technical standards. The increase in the total numbers of tunnels (Fig. 1) as well as the need for future re-investments in existing tunnels show the overall economic impact and justify the change towards the life-cycle perspective."

Jan 1, 2016

By James J. Scott

Longwall mining has not received a great deal of attention in the United States; however, this system offers many advantages over the conventional room-and-pillar methods now being used. In order to conserve the coal resources of this country, the U. S. Bureau of Mines has investi¬gated the feasibility of adapting European longwall mining methods to American coal seams. Their studies showed longwall mining to be well suited to thinner seams and, greater depths; and, in addition, permitted almost 100 percent recovery of the coal. Most, experiments with this method resulted in higher overall production-costs than were commonly obtained with highly mechanized room-and-pillar techniques This high cost-was largely due to the excessive amount of labor required to maintain adequate roof support with conventional longwall mining techniques. With the substitution of hydraulic-powered, self-advancing roof support systems for conventional supports, this excessive labor cost has been decreased, and longwall mining costs are now competitive with those of modern room-and-pillar mining.

Jan 1, 1964

By A. Balint

The Photometric Optical Separation process is introduced and examples of sorting machines are given. Applications of the process are outlined in general terms with reference to specific types of industrial installations. Brief description is given of the capabilities and limitations of available equipment, including cost estimates.

Jan 1, 1967

By R. L. Stone

By means of laboratory balling tests and a procedure for determining bentonite concentration in a green ball the present study revealed that the bentonite savings by mulling concentrate and bentonite prior to balling was sufficient to warrant installation of a full-size unit in a pellet plant. On the basis of this work, a muller was put on stream at Bethlehem Steel Corporation's Cornwall pellet plant in June 1969, and has operated continuously since then. Plant tests showed that the use of the muller resulted in bentonite savings of about -502 without any loss of green, dry, and fired ball quality. Virtually no maintenance problems have been encountered. This information is important to future pelletizing operations both from the standpoint of product quality and economics.

Jan 1, 1971

By G. P. Larson

We define a specialized mineral market as follows: Specialized Markets are markets where a low volume of a given mineral is used to convey a large benefit to a specific product. Sales of these value added minerals to small markets generally require a different marketing approach compared to bulk or commodity markets for traditional minerals. Specialized and commodity markets are differentiated by several characteristics as listed in Table 1.

Jan 1, 1990

By Gene Mattila

Each installed rock bolt costs in excess of 520.00. High cost in conjunction with the primary purpose of safety makes it only logical to install the highest quality anchors possible. Each bolt has designed support capabilities in axial, shear and fluctuating ground condition, if installed to manufacturers recommendations. The quality of anchor is not; however, only affected by material specifications, but by transportation, handling storage, installation procedure, machine performance and geology. The quality is not only affected by many variables, but reliability should be assured. Non-destructive methods of testing reliability are only available for several types of bolts.

Jan 1, 1985

By James O. Mawyer

Fuel is a major .cost for power generating utilities. Virginia Power is completing one of the nation's largest coal reconversion programs. As a result, 10 million tons of coal will now be used at six generating stations. Four of these stations are located on naviagable waterways. They consume over half of Virginia Power's coal. Historically, railroads have exclusively served these plants. In an effort to substantially reduce fuel cost, Virginia Power has reexamined transportation logistics and is proceeding with barge delivery. A phased approach was used by Virginia Power for the transportation program. Plant requirements were first identified. Coal sourcing issues were then examined. The concept of intermodal transportation was investigated. The bottom line cost savings was used as the criteria for continuing the project. The results thus far have been gratifying. Virginia Power has begun to implement barge transportation.

Jan 1, 1986

By Randall C. Divito, Craig R. Eckdahl, Bruce D. Wagener, Joseph Klejwa

The existing Central City Tunnel was built primarily in the 1930s with a small portion as old as the 1880s. It conveys stormwater in downtown Minneapolis. It is a 4,400-ft long tunnel located 80 feet underground. The Central City Tunnel has experienced surcharging and surface overflows during heavy rainfall events. This paper presents the details of tunnel and shaft design for the new Central City Parallel Tunnel to mitigate the overflows. The design considered hydraulics and geotechnical engineering for the structural geologic conditions including the weak Saint Peter Sandstone and overlying strong Platteville Limestone. Ground conditions resulted in tunnel designs including large flat-back box tunnels and unique cathedral-shaped tunnel sections.

Jun 13, 2023

By N. Arbiter

Introduction The theoretical analysis of tumbling mill energetics and performance has largely neglected mill dimensionality, and, in particular, the importance of the length/diameter (L/D) ratio. This is in spite of the fact that practice varies substantially: geographically, for semi-autogenous and autogenous mills, as between North America and South Africa/Scandinavia, and historically, for overflow ball mills, for which the L/D ratio has increased significantly from the earliest small mills to the largest mills currently. The present study is concerned primarily with the influence of the L/D ratio on the design and operation of overflow ball mills, on the occurrence of the overload phenomenon, and on the limits, if any, it may impose on mill capacities because of critical pulp axial velocity limits. It will be shown that the shape factor is of major importance in this area and that its adjustment to the extent that this is practical should remove the diameter limitations previously postulated for this mill type. Dimensionality in mill design Ball mill shape factors in the period prior to 1927 (Taggart, 1927) averaged 1.1/1 for 29 center discharge mills and 1.0/1 for 30 peripheral discharge mills. With the resumption of new plant construction after the 1930s depression, the Morenci concentrator continued the 1/1 ratio with its 3.1 x 3.1 m (10 x 10 ft) mills. The ratio was increased progressively from then on, reaching 1.6 and 1.8/1 for the largest overflow mills currently. As shown recently (Arbiter, 1989), this is in sharp contrast to autogenous and SAG mill shapes, for which the ratio averages 0.4 in North America. On the other hand, South African practice, starting at the turn of the century with autogenous mills having 4/1 ratios, moved toward 1/1 until recently, when a 2.5/ 1 ratio mill was installed. The reasons given for such divergent practice for mill shape factors are in some respects contradictory and generally inconclusive. The most complete discussion from a practical viewpoint (Dor and Bassarear, 1982) is limited to primary SAG and autogenous mills. Considerations of ball mill dimensionality have had a twofold direction. On the one hand, it has been argued that ball mill efficiencies should increase with increasing diameter and that the specific energy for a particular grind should be reduced accordingly. An inadvertent test of this idea at the Bougainville operation (Burns and Erskine, 1983) resulted in drastic underpowering, which led to failure to reach design capacity until additional mills were installed. This can be taken as strong evidence against any increase in efficiency with diameter. In another direction, it has been argued (Arbiter and Harris, 1982, 1983) that there is a limit to ball mill diameters because of the demonstrable limit to axial flow velocities evident in the overload phenomenon, which as a fact is incontrovertible. But that it places a limit on mill diameters overlooks the evidence given below that appropriate variation in the L/D ratio will permit major increases in diameter, limited only by constructional or economic factors. The present study was directed toward quantifying the overload phenomenon through examination of the influence of mill dimensionality variation and mill operating variables on its occurrence. It is shown that varying the operating conditions, specifically the load fraction and the fraction critical speed, can reduce the risk of overload for existing operations; while appropriate decreases in the L/D ratio can minimize the risk in the design of new circuits. Ball mill overload Ball mill overload is a consequence of the approach to a critical velocity with increasing feed rates or circulating loads. Although the effect has been known for over 50 years, there have been no previous attempts to quantify it. The following description of the ball mill as a flow system is the preliminary to a quantitative analysis: 1) In the absence of a ball load, axial flow of pulp through a mill resembles open channel flow, except for disturbances near the shell due to shell/lifter rotation. 2) For a given ball load (Lf), the void fraction available for pulp hold-up (H) for the ascending portion of the load is approximately 0.4 Lf. In the descending portion, it is greater than this and increases with fraction critical speed (Fc) because of load expansion. 3) Increasing the feed rate increases pulp hold-up and progressively fills the available void space. At a critical flow rate, which depends on system geometry, hydraulic head and pulp rheology, void filling reaches its limit; a pool forms rapidly and fills available space outside the ball load and up to the overflow level. Prior to this, pulp discharges mainly along the ascending rim of the overflow. 4) For a small mill (Lo et al., 1990), it has been shown that with increasing feed rates the critical filling is at or near 50% of the mill volume. Power drops rapidly when this level is reached, as required by the torque formula. 5) The transition to overload is associated with the following phenomena: a) The decrease in power draw. b) Damping of mill sound. c) Reduced comminution of coarser feed sizes, probably due to reduced direct impact in the presence of a pool. d) Increased circulating loads, which further intensify the overload, and increased density of cyclone underflows, which can lead to roping. e) Conditions beyond overload are not known because feed rates are not delibelrately increased beyond this point. f) The existence of the phenomenon limits the capacity of a mill with a fixed set of operating conditions and can prevent the balancing of hard ore feed rate decreases by increases in soft ore rates.

Jan 1, 1992