Search Documents

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By D. S. Parasnis

The early beginnings of mining geophysics in Sweden can be traced back to the reign of queen Kristina in the 17th century. The mine compass, consisting of a freely suspended magnetic needle in a casing, was in use certainly by 1640 and probably earlier for locating iron ore deposits. Whether the mine compass was a Swedish invention or not is an unsettled question since the possibility cannot be overlooked that the celebrated Nürnberg compass-makers of the 16th century may have constructed it for the first time(1). Be that as it may, the mine compass was very extensively employed in Sweden for more than two centuries and met with spectacular success in locating magnetic deposits under shallow overburden. Occasionally the diligent prospector would even be rewarded with a pyrrhotitebearing sulphide deposit, as witness many old sulphide-ore pits and some mines still in operation from the 17th and the 18th centuries. The mine compass measured only the orientation of the Earth's magnetic field and not its strength. Although it was improved in construction and sensitivity over the ages, no great strides were made in magnetic prospecting after the initial discovery of the use of the compass until Gauss, omnipresent in 19th century physics and mathematics, showed with the assistance of Weber how the strength of a magnetic field could be determined.

Jan 1, 1975

Industry and regulatory agencies have requested guidance on safe blasting near transmission pipelines. The U.S. Bureau of Mines and AMAX Coal Company have studied surface coal mine overburden blasting near four steel and one PVC pipe-line of 15 to 5l-cm diameter, monitoring vibration, strain, and pressure. Unlike tests simulating construction blasting, these were up to 1000 kg per delay in 3l-cm blastholes. Worst case comparisons showed that 12.7 cm/s blasting vibrations produced strains about 1/4 that of pressurization and 10-18 pct of the ultimate tensile strength. No failures occurred from blasting as close as 15 m which produced vibrations over 60 cm/s.

Jan 1, 1994

By D. R. McMullin

The purpose of this paper is to provide a method for mine planners and engineers to evaluate on a conceptual basis if a shaft or a ramp is most suited for their particular underground access requirements. Mine planners and engineers are often raced with the decision of choosing which method of underground access is best suited for their particular requirement. Underground access can be provided by a shaft, ramp, adit, or slope for either exploration and/or actual production operations. This paper will focus on the construction cost and schedule differences between sinking a shaft and excavating a ramp which are currently the most typical access alternatives used in the western United States. It would be wrong to state that one method is superior to the other in every case. There are many variables to be addressed, and the degree of sensitivity of each of them will eventually dictate which method is the most suited to the particular circumstances. This paper compares the construction cost and schedule or sinking a shaft to excavating a ramp at different depths given different ground and hydrological conditions. This comparison provides mine planners with "rules or thumb" that may be applied to the access selection process.

Jan 1, 1994

By B. Anameric

Considerable effort has been directed towards understanding the carbothermic reduction mechanisms of self-reducing, fluxing dried green balls to produce pig iron nuggets. Given the geometry of the situation, some investigators believed that the shrinking core model was applicable. Hence, this study involved investigation of the applicability of the shrinking core model to pig iron nugget production. The experiments involved heat treatment of dried green balls utilizing either a laboratory-scale resistance box furnace or a gas-fired muffle furnace at various furnace temperatures and residence times. The products were analyzed for the following: (i) preferred reaction pattern, (ii) distribution of the metallized areas, (iii) % iron content variation in the pig iron nuggets from surface to center, (iv) carburization pattern and (v) physical and chemical properties of the pig iron nuggets. It was determined that the reduction of iron oxide occurred simultaneously throughout the sample and not beginning at the surface and propagating inward; thus the shrinking-core model was not applicable. Heat transfer and gas diffusion from surface to center were not the rate-limiting steps for reduction and carburization reactions.

Jan 1, 2011

By M. Stuart

The copper-silver-mercury orebody of Gortdrum Mines (Ireland) Limited is located 3 miles north of the town of Tipperary in the Republic of Ireland. A drilling programme from 1964 to 1966 delineated an ore¬body of 4.19 million tons of copper ore assaying 1.19% Cu and 0.75 ozs per ton Ag, which could be mined from an open pit. Testwork having shown that the ore was amenable to conventional flotation techniques, it was decided to build a concentrator of 500,000 tons ore per year capacity. Stripping of the open pit commenced in 1966 and in the autumn of 1967 the concentrator started up. The first shipments of concentrates were made to the smelter in Europe in late 1967. In the spring of the following year, word was received from the smelter that these early shipments contained between 1% and 2% Hg, and that the smelter could not accept further shipments of this quality.

Jan 1, 1973

By Vernon R. Shorter, Wayne N. Clark

Introduction Coal is the US's largest indigenous fossil fuel resource and is used to power 57% of this country's electrical generation (NCA, 1986). Congress, however, is focusing its attention on the acid rain issue and public sentiment is leaning toward further curtailments of SO2, NO, and particulates from utility and industrial coal-burning facilities. The Cool Water plant has proven that integrated-gasification-combined-cycle (IGCC) technology can reliably produce economical electrical power while limiting SO2, NOx, and particulates to a rate of only one-tenth of the federal New Source Performance Standards for coal-fired plants. Process water requirements at Cool Water are 40% less than those of a conventional coal-fired utility plant equipped with flue-gas desulfurization units for stack gas scrubbing, thus reducing waste water treatment requirements (Clark and Shorter, 1985). The IGCC technology employed at Cool Water has now been demonstrated to efficiently convert coal to electricity in an environmentally superior fashion. The Cool Water Coal Gasification Program is an unincorporated California association of six partners whose commitment is proving that the integration of gasification with combined cycle power production (IGCC) is commercially viable and environmentally safe. The 120 MW Cool Water plant began commercial production on June 24, 1984. The Program is operating it for a five-year commercial demonstration period. The Program is about halfway through this period. Much of that which was intended to be proven is now fact. In this mid-term assessment, the authors report that the com-

Jan 2, 1987

By Y. C. Kim

This paper reviews the past 18 months of geostatistical work in a coal deposit performed jointly by the University of Arizona and the Homer City Owners. The objective of the study was to better predict the in-seam sulfur values of the deposit for the purpose of future emission control. Based on initially available 112 DDH information, variogram models were developed for Sulfur, Ash and Thickness for the entire deposit. The deposit was then kriged using 333 m x 333 m (1000 ft x 1000 ft) panel size. The estimation variance information obtainable from geostatistics was next utilized to improve the development drilling activities that were underway. The results of this effort are presented in this paper. In addition, this paper describes (1) the reasons for preferring kriging over the conventional isopachs, (2) the results of empirical validation of the kriged estimates using 19 additional DDH information, and (3) up-to-date experience on the use of conditional simulation of the same deposit for the future emission control strategy development.

Jan 1, 1980

By R. Krog, S. Schatzel, H. Dougherty

Longwall coal mine operators in the U.S. are required to ventilate multipanel longwall districts, but may have little or no knowledge about what happens to the ventilation air between the inlet evaluation points (IEPs), bleeder evaluation points (BEPs) and bleeder fans. The effectiveness of bleeder performance can directly influence the ability of a ventilation system to remove and dilute coal bed methane emissions. U.S. coal mining stakeholders have acknowledged their belief that the T-junction split at the longwall face tailgate corner is very important in controlling the distribution of ventilation air. To obtain direct measurements of bleeder performance, a tracer gas, sulfur hexafluoride (SF6), was released into the ventilation air stream on active and inactive longwall panels. Testing was performed on multiple longwall panels that included various phases of longwall development and variable path lengths of ventilation air transport to bleeder fan installations. Changes in the T-junction ventilation air distribution over the life of a longwall panel, and its variable effect on panel ventilation airflow are discussed. These findings will assess the effectiveness of commonly applied ventilation strategies for improving air distribution and ventilation controls to meet statutory requirements.

Jan 1, 2011

By J. B. Offei, K. Awuah-Offei

Mining companies registered with the SEC were required to comply with Regulation S-K 1300 for their annual report covering the first fiscal year ending on or after January 1, 2021. Consequently, most mining registrants filed their first S-K 1300 compliant disclosures in 2022. The US Securities & Exchange Commission (SEC), as part of its disclosure review program, has been issuing comment letters in response to these filings. This paper presents an overview of the trends in these comment letters. The authors reviewed comment letters retrieved from the SEC’s EDGAR database based on Standard Industrial Classification (SIC) Codes that cover mining, the content of the comment letter (whether it references S-K 1300 or not), the names of SEC staff listed in the comment letters, and other criteria. The analysis shows the SEC staff's reviews have been comprehensive covering the breadth of S-K 1300 and eliciting compliance with the rule. The staff through their comments are eliciting all the disclosures required by S-K 1300 and are not allowing registrants to substitute disclosures based on other standards for S-K 1300 disclosures. It is important, however, not to over generalize as the comments are based on the particular context.

Feb 1, 2023

By K. F. Unrug

Martin County Coal Corporation is located in Martin County, Kentucky in the Appalachian coal fields, near the West Virginia border. The total leasehold covers more than 33 000 acres. Total annual production at Martin County Coal Corporation is currently 2,500,000 tons, but in certain years exceeded 3,000,000 tons. Approximately 45 percent of the annual production comes from two surface mines. The balance is produced from five underground mines. Martin County Coal Corporation's work schedule consists of 240 days/year, two nine-hours shifts/day.

Jan 1, 1991

By S. K. Kawatra

A high calcium fluid-bed combustor ash has been shown to be an effective binder at dosages of 1 to 2% of the magnetite concentrate weight. Magnetite pellets 1.3 cm (1/2 inch) in diameter were produced with dry crushing strengths greater than 22.3 Newtons/pellet (5.0 pounds force/pellet), which is comparable to the results produced using conventional bentonite binder. The effectiveness of fly-ash-based binders was considerably improved when calcium chloride was added as an accelerator. Addition of calcium chloride at a rate of 0.1 to 0.2% of the total powder weight increased the strength of dried pellets by as much as 22% compared to the strength of pellets made using fly-ash without accelerators.

Jan 1, 1997

By G. Ferrara

During several years of operation in Europe, South Africa and other countries, the Tri-Flo has demonstrated to represent a substantial improvement of the dense medium dynamic separation systems. The reasons are: (1) high sharpness separation due to the multistage system and the application of new concepts in designing the regeneration circuit and controlling the medium rheology; (2) the possibility of performing two cuts at different densities using a since separation device and a single regeneration circuit. The paper discusses in detail the above mentioned points, with particular reference to the multistage technology, based on the circuit analysis theory, and to the control of the medium rheology based on recent work in the modelling, and simulation of the rheological behavior of dense suspensions.

Jan 1, 1993

By H. Nemutolluhi

Discussion by G.E. Agar In the April issue of Mining Engineering there is a technical note "New size laboratory ball mill for Bond Work Index determination" written by M. Nematollahi which is very confusing. My recollection is that a description of an experimental procedure should be such that someone skilled in the art should be able to reproduce the results. Applying this test to this particular article would according to me cause a failure to be registered. There are apparently three batch laboratory test procedures referred to in the article. One of these is the traditional Bond test with all its limitations such as dry grinding followed by exclusively dry screening, two attributes which fail to simulate conventional industrial grinding. There is a second procedure (NSBM) which the author is advocating as an improvement of the Bond procedure but from the description I doubt that anyone would be able to repeat the procedure. For instance, is the grinding to be done wet or dry, if wet at what pulp density, and how is the screening to he done, wet or dry or a combination? On top of that uncertainty the author refers to a simplified "Anaconda" test. No reference is provided for this procedure and in the text the results of the technique are referred to "Denver wet ball mill" results and say nothing of Anaconda results. Reply by H. Nematollahi I think that the method proposed to determine the Bond Work Index in this paper is clearly described in the paper as follows: •The method of grinding is dry (Ref. paragraph I, subject Method description); •The size of ball mill, the quantity and size of balls are noted (Ref. paragraph 1, subject Test equipment); and The test procedure is described in detail (Ref. paragraphs 1, 2 and 3, subject Test procedure). As it is noted in the paper, the test has been worked out under the same condition as Standard Bond Test with ball mill, so dry (screening should be dry also), but using a smaller ball mill and a smaller quantity of sample. Considering the above mentioned points, I believe that the method has been fully and clearly described and it ought to be repeatable as well. The Anaconda test is a method for determination of Work Index and could be done by any types of laboratory wet ball mill (Yan, R.F., et al., cf. References). I applied this method using a laboratory Denver ball mill (Ref. paragraph I subject Determining the Bond Work Index). So the results referred to Denver wet ball mill can be equated the same as Anaconda method.

Jan 1, 1996

By D. C. Yang

A practical and economical flowsheet has been developed and demonstrated by integrating the packed column flotation with the GranuFlow process for fine coal recovery. Orimulsion, which was used as an additive, served a dual purpose: first in the flotation and second in the dewatering and granulation steps. The test results on the coal preparation effluent sample show that Orimulsion is flexible and compatible with fuel oil and various frothers used in the packed column. Clean coal with ash contents of 3.0, 3.7, 4.3 and 5.1% were produced from a head sample of 33% ash at combustible matter recoveries of 72.4, 81.1, 87.5, and 89.2%, respectively. Other advantages include high throughput, low moisture, improved handleability, and reduced dustiness of the dewatered coal, thus providing a very significant economic Incentive for the integrated process.

Jan 1, 1998

By Rajat Gangrade, Haotian Zheng, Jarrett Smith, Daniele Nebbia, Mike Mooney

The application of artificial intelligence (AI) to improve tunnel boring machine (TBM) operations requires a significant amount of information to train robust performance prediction models, e.g., for tunneling-induced settlement, productivity, tool wear, etc. This paper presents the AI framework applied to the North-East Boundary Tunnel (NEBT), the largest component of the Clean Rivers Project in Washington, DC. The paper focuses on required elements for real-time AI use to estimate tunneling-induced ground and building deformation and cutter tool wear. Keys to the framework include defining the necessary quantities of data required as well as the process of windowed training, validation and model testing. To date, the models developed for ground deformation and tool wear show satisfactory performance when compared to observed field observations during tunneling.

Jun 13, 2021

By M. A. Schimmelpfennig, A. D. S. Gillies

M.J. McPherson Having worked on the thermodynamics of air/liquid-water mixtures passing through the surface fans of deep mines, I find this paper of great interest and congratulate the authors on producing it. There are two matters, however, deserving discussion. First, the authors have described the classical theory of fog formation with fogging occurring at "supersaturation." In fact, the process of fog formation begins well below 100% humidity. The more strongly hygroscopic nuclei in the atmosphere will attract water molecules and begin to grow at a relative humidity perhaps as low as 70%. The process is a dynamic one with both condensation and evaporation taking place throughout the mixture on microscopic liquid surfaces. As saturation is approached, the rate of condensation accelerates rapidly producing the familiar reduction in visibility. Hygroscopic nuclei are present in all natural atmospheres and under the appropriate conditions of pressure and temperature, will produce clean fogs. However, if the air is polluted by particulates from combustion or other processes then the resultant coagulation with growing liquid particles may produce dense (and sometimes photochemical) smogs. It is this process that is likely to occur in underground mines when moist air is cooled below dew point. Second, the authors have summarized very well the individual measures that might alleviate the problem. In particular, I agree that neither heating nor refrigerating the air, by themselves, provides a satisfactory solution. However, there is a combination of these that provides a neat and effective control of fog formation. This involves a small, self-contained refrigeration unit within a duct but without the usual external heat rejection facility. The air is cooled below dew point and, hence, dehumidified on passing over the cold evaporator coils. The heat from the condenser is rejected back into the air downstream from the water eliminator, as shown in Fig. 1. The duct configuration can be designed to create good mixing at the outlet. I have used a climatic simulation program to illustrate the effect, assuming a 500-m (1,640 ft) long airway of cross section 60 m2 (645 sq ft), an airflow of 9 m3/s (318 cu ft per sec), inlet conditions of 19/19.25°C (66/67°F) wet bulb/dry bulb temperatures, a virgin rock temperature of 17°C (63°F) and typical rock thermal properties for a hard-rock mine. I have also assumed that 10% of the rock surface is wet. Figure 2 shows the variation in temperatures along the airway if no measures are taken. The relative humidity remains close to 100% and condensation will occur throughout the length of the airway. Before any such installation is designed, the exercise must, of course, be repeated for each location with accurate data. However, this example demonstrates the potential of the system. The idea is not new - the principle is sometimes used in air-conditioning plants for buildings. Figure 3 shows the effect of removing 30 kw of heat by evaporator coils sited 40 m (131 ft) along the airway and rejecting that heat (plus another 10 kw of compressor and fan power) into the air at 60 m (197 ft). Condensate water is produced, at a rate of 0.45 L/min (0.12 gpm). The result of this sequential cooling/dehumidification/heating process is to separate the wet and dry bulb temperatures along the length of the airway. The relative humidity increases from 80% at the duct outlet to 92% at 500 m (1,640 ft). The airway is maintained free from fog.

Jan 11, 1983

By John M. Smith

Kaolin is an important industrial mineral because of its unique properties and low cost. Strictly defined, kaolin is the name given to a group of hydrous aluminum silicates of which kaolinite is the most common mineral (1). Through common usage the mineral, kaolinite, is called "kaolin" or "china clay". In 1972 over 4, 000, 000 tons of kaolin will be beneficiated and shipped by domestic producers. By far the largest user of kaolin is the paper industry which utilizes approximately 65 to 70 per cent of the total production. Kaolin is used in paper as a filler in the interstices of the sheet and as a coating to impart smoothness, gloss, brightness, and printability to the paper. The rubber industry is also a large user of kaolin where it is used as a filler because it adds strength, abrasion resistance, and rigidity to both natural and synthetic rubber goods. Kaolin is used as an extender in paints because it is chemically inert, has a high covering power, gives desirable flow properties, and is low in cost. In ceramics, kaolin is used in whitewares, tile, insulators, refractories, and in some face brick where a white color is desired. Kaolin is also used extensively in plastics as a filler in thermosetting and thermoplastic mixes to give smoother surfaces, a more attractive finish, good dimensional stability, and resistance to chemical attack. Many other process industries use kaolin as a filler, suspending medium, or for color improvement.

Jan 1, 1972

By H. Fayed

Froth flotation technology is the backbone of the minerals pro-cessing industry where minerals are concentrated by selective separa-tion; either direct or in-direct flotation. In direct flotation useful minerals are conditioned to become hydrophobic (water-repellant) and attach to air bubbles while impurities (non-useful particles) remain in water. The hydrophobic particles are transported by air-bubbles to the top froth (foam) layer in flotation tank which can be removed as a concentrate. There are many factors that controls this selective separation process such as: particle’s degree of hydrophobicity, size, mass loading, air holdup and bubble size distribution. Turbulent fluctuation of the slurry in the tank is another important factor that controls the collisions rate between particles and bubbles and hence attachment rates. The turbu-lent fluctuations are measured by the local distribution of turbulent dissipation rates. Conventional flotation machines are restrained by residence time of the slurry that is about 3-5 minutes that results in a large footprint and limits the capacity of flotation plants. The designers of conventional flotation machines try to reduce the footprint of flota-tion tank by scaling up the flotation machines to increase plant throughput. The scale-up process reduces the specif power consump-tion and the local distribution of shear rates and turbulence dissipation rates. This scale-up results in a larger mean bubble size and lower particle-bubble attachment rates.

Feb 1, 2023

By Van Price

Some technical developments of the National Uranium Resource Evaluation Program which are of general application in geochemical exploration are being studied. Results of stream water and suspended and bottom sediment analyses are compared for an area near Williamsport, Pennsylvania. Variations of uranium content of water samples with time in the North Carolina Piedmont are seen to correlate with rainfall. Ground water samples from coastal and piedmont areas were analyzed for helium. All media sampled provide useful information when properly analyzed and interpreted as part of a total geological analysis of an area.

Jan 1, 1979