Search Documents

By Avula Rajashekar Yadav, Sreenivasa Rao Islavath

Barrier pillars and gateroads play a vital role for the safe exploitation of coal from the panel in the longwall workings. The barrier pillars and gateroads are subjected to the front abutment and side abutment loads during the retreat of the panel. These structures may fail if the developed load on them is higher than their strength. The stability of the longwall structures such as barrier, gateroads and face is paramount in extracting the coal from the panel safely. For this, a deep longwall mine in India is chosen for the study using a 3D numerical modelling technique. In this paper, three critical conditions such as scenario 1 (no side goaved-out panel), scenario 2 (with side goaved-out panel) and scenario 3 (with two side goaved-out panels) are taken. For each scenario, five retreat distances such as 100, 125, 150, 175 and 200 m are considered for detailed investigation. The development of vertical displacement in gateroads, vertical stresses on barriers, vertical stress concentration factor, abutment zone and yield zone for longwall face are extracted and analyzed. Also, the safety factor of the barrier and longwall face is estimated considering the Hoek–Brown rock mass failure criterion. From the study, it is observed that the maximum vertical displacement of 121 mm in TG3 at scenario 3 for a retreat distance of 200 m and a minimum vertical displacement of 33 mm in TG2 for a retreat distance of 100 m at scenario 2. The development of vertical stress on the barrier is found to be between 8.78 and 13.40 MPa, and the safety factor of the barrier lies in between 1.56 and 1.80. The study also revealed that the yield zone at the longwall face lies within 2 to 3 m.

Dec 29, 2023

By G. A. Kordosky

There are a number of reasons why the solvent extraction of molybdenum deserves attention: 1. The solvent extraction chemistry of molybdenum is interesting and complex, 2. The price of molybdenum is predicted to average about US$ 20.00 / pound in 2010 and, as China, India and other countries develop, the demand for specialty steels will increase putting long term demands on molybdenum supply, 3. Uranium ores often contain significant concentrations of molybdenum[1] and typically yellow cake will have a moly specification which when exceeded brings penalties, and 4. The valuable metal rhenium is a byproduct of molybdenum recovery circuits.

Jan 1, 2010

By Fredrick C. Kruger

We can confidently predict such obvious long-term trends affecting the minerals industry as - increasing consumption, exhaustion of easily discovered near-surface ores, and sharp limitations upon open pit mining by environmental considerations. There- fore, we must intensify the exploration for, and the development and exploitation of, deep bodies of potash and other ores. This paper examines the state of the art of the search for, and the evaluation of, potash from both a geological bias and a mining practicability. The use of indirect geological methods and geophysical techniques, followed by expensive deep drilling, are the conventional approach to evaluation and development of mining plans. The geologist and the geophysicist will have to find ways to perform both of these tasks better and cheaper.

Jan 1, 1973

By J. A. Botín

Mining investment decisions are difficult since decision analysis is often based on scarce information. The sources of uncertainty in large mining investment projects are particularly numerous and are present in all evaluation stages. Hence the feasibility decision for projects of this nature will largely depend on how well these sources of uncertainty are managed to achieve bankable risk levels. The risk associated to the construction stages of a mining project is particularly difficult to quantify, mainly because the large number of variables affecting constructive yields, and the complex interactions among constructive resources. This investigation focuses on developing quantitative simulation models and tools to increase the value of a mining project by means of an optimization of the preproduction equipment fleet. The models were validated through their application in the Chuquicamata Underground Mining Project.

Feb 23, 2014

By Anthony S. Spearing

The vast majority of the estimated 100 million rock anchors installed in mines in the USA per year use resin cartridges (Tadolini and Mazzoni, 2006). About 4.5 million per annum of these are bolts with a mechanical shell that if properly installed become effective active supports on installation. In addition, cable anchors (mostly passive) are installed with typically 4 ft of effective resin anchorage length sometimes with mechanical shells, which further makes the installation more difficult. This is because the cable (even with a stiffener tube) is not very rigid. When installing bolts with mechanical shells and cable bolts in the holes, the back-pressure can be so high that the installation is unsuccessful often creating a ?spinner? (an un-tensioned bolt) at best or buckling the bolt thus requiring another bolt/cable to be installed, or leaving a poorly functioning unit. The installation problems can create a significant potential safety hazard and waste time and money. Using a purpose designed test rig that physically inserts different rock anchors into pipes with resin and measure the back-pressure developed with time during the insertion/ installation. The test installation procedure is designed to mirror that used underground by rockbolt operators in coal mines. In addition a computer model has been calibrated that can predict the approximate back pressure of new anchor and resin combinations acting as a screen before physical testing. This research has lead to an understanding and quantification of the insertion back-pressures and this already resulted in improved prototype designs that could lead to more reliable mechanical shell and resin bolt installations.

Jan 1, 2009

By Ritika Kundu, Moussa Wone, Amanda M. Morgan, Tatiana K. Proctor

The Piney Branch CSO 049 Storage Tunnel (PBST) will be the last major project for the DC Clean Rivers Program. The project includes construction of a 2,200-foot-long, 18-foot-internal-diameter storage tunnel; two connections to combined sewer infrastructure; and two shafts. Major challenges include excavation underneath an existing live outfall that must remain in service; excavation of the tunnel through several areas of low rock cover and mixed-face conditions; and negotiations with a variety of federal, regional, and local stakeholders to address project impacts. This paper describes the overall project scope; geotechnical conditions along the alignment; design and construction challenges; and construction procurement.

Jun 23, 2024

By A. H. Srnallbone

Over the past few years the rising production costs, shortage of skilled labor, and increased use of lower grade ore bodies have all added justification for the use of on-stream analysis. A rise in the number of on-stream units indicates that this type of assay is now being accepted as a necessity. On-stream analysis is a much more rapid means of obtaining true assays of a flowing product when compared to wet chemistry or "grab" samples dried, briquetted and assayed by x-ray. In contrast, on-stream analysis uses real time samples assayed every 30 seconds while each stream is assayed every 5 to 15 minutes. It is very important not only to know that a change has occurred in the process, but to know what caused the change and how to correct for the change. For example, in a tailing sample the elements of interest comprise between 1% and 10% of the sample. The remainder is water and gangue. Previously the gangue was not assayed nor were the low atomic number elements used for corrections. In addition to the demand for higher accuracies some concentrators were being penalized for excessive Ca or in some cases 5i in their concentrates. This penalty was being imposed by the smelter in order that they could better cope with pollution problems and prolong the life of their furnaces. But until Ca, 5i, and S are measured on-line, nothing can be done about their control. By accurately measuring these light elements on-line, a complete assay is obtained of the total sample providing improved accuracy for the important products. The justification for complete accuracy assays is now even more obvious because they are possible at very 1ittle increased cost and at no increase in analytical time.

Jan 1, 1977

By A. Arik

Reliable ore reserve estimates for deposits with highly skewed grade disributions are difficult tasks to perform. Although some recent geostatistical techniques are available to handle problems with these estimations, ordinary kriging or conventional interpolation methods are still widely used to estimate the ore reserves for such deposits. The estimation results can be very sensitive to the search parameters used during the interpolation of grades with these methods. This paper compares the ore reserve estimates from ordinary kriging using several cases in which certain search parameters are varied. The comparisons are extended to different mineralizations to show the changing effects of these parameters.

Jan 1, 1990

By S. El-Mofty, P. Zhang, N. A. Khalek

This article reviews different technologies used for beneficiation of siliceous and calcareous phosphate ores of different origin. The review sheds light on recent trends suggested for solving problems associated with separation of different impurities from phosphates. Applications of recently modified flowsheets as well as new reagents in the flotation of phosphate ores of sedimentary origin are highlighted.

Jan 1, 2003

By Clark Harrison

It is not uncommon for overall quality of coal from a mine to deteriorate as the mine is developed or for an improved-quality coal specification to be imposed during the life of the mine. Either of these conditions typically results in management pressuring mine personnel to take greater care in delineating the seam from top and bottom rock. When mining and seam conditions require a portion of the seam to be removed to ensure sufficient rock is removed to meet the quality specification, physical-coal cleaning may become economically competitive with in-pit seam grooming. The additional cost of coal cleaning may, in some cases, be justified by permitting higher recovery of the coal seam than is possible when cleaning the seam with excavators in the pit. This paper compares projected coal cleaning results with present in-pit grooming techniques and reports the economic results.

Jan 1, 1987

By Albert R. Rule

Beneficiation studies were made by the Bureau of Mines to develop a process for concentrating phosphate minerals from the altered rock of the Phosphoria Formation. This report describes research on intermediate - and marginal-grade ores from southeast Idaho, The process developed consists of attrition scrubbing and sizing to produce a coarse concentrate; desliming at about 800 mesh (18.5 microns); flotation of the fine sands; roasting of the combined concentrates for removal of organic carbon and combined water; and leaching with SO2 for removal of magnesium and nonapatitic calcite. Results of continuous tests on three different ore types showed that approximately 80 percent of the available phosphate can be recovered at a grade suitable for phosphoric acid production. While leaching with SO2 is not necessary for all ore types, it is an important step in purifying concentrates containing excessive magnesium.

Jan 1, 1966

By N. W. Johnson

The behavior of non-sulphide gangue in chaloopyrite flotation circuits has been investigated. Plant and laboratory tests were carried out on five different ores, and linear relationships were found to exist between the rates of recovery of water and free nonsulphide gangue in the concentrates although there was evidence from pilot plant tests that these were linear approximations to parabolic curves over the limited regions which were observed. There was evidence that the free non-sulphide gangue enters the concentrate by hydraulic classification and a classification function has been proposed to define this behavior. This function is suitable for inclusion in a mathematical model of the process.

Jan 1, 1972

By J. A. Marts, R. C. Gilmore, Jr. Bogin, S. A. Saki, J. F. Brune, J. W. Grubb

"Colorado School of MinesResearchers at Colorado School of Mines (CSM) have developed computational fluid dynamic (CFD) models to study gas distributions and explosion and fire hazards in longwall gobs. In underground coal mines, methane continuously emitted from surrounding strata mixes with air from active mine workings and may form explosive gas zones (EGZs). Some western United States coal mines are also prone to spontaneous combustion (spon com). Insight into oxygen concentrations within the gob is crucial for assessing spon com hazards and mitigation strategies. Nitrogen injection used in conjunction with progressive gob sealing can reduce EGZs and spon com hazards by forming a dynamic seal that separates the methane in the gob from the air that ingresses from the face. This paper describes CFD modeling simulations studying the formation of such dynamic seals by optimizing the nitrogen injection locations. The impact of nitrogen on oxygen ingress and formation of EGZs is discussed. Optimum nitrogen injection quantities and injection locations were determined. Dynamic seal formation is most effective if the headgate nitrogen injection locations are split between the first crosscut inby the face and a second location about 300 m (1,000 ft) further inby. INTRODUCTION Underground longwall coal mine ventilation systems are designed to dilute hazardous gases and to provide breathable air to miners working in the area. Methane gas is liberated as the mining process extracts the coal and disturbs the surrounding strata. Methane mixes with the ventilation air and often produces explosive gas zones (EGZs) within longwall gobs (Brune 2013). Past CFD modeling research of underground coal mine ventilation systems has shown the effects of face air quantity on EGZs (Worrall 2012) and nitrogen injection to control spon com (Balusu et al. 2005; Ren et al. 2012; Ren et al. 2011; Smith and Yuan, 2008; Yuan and Smith, 2014). Other modeling approaches include network ventilation models of oxygen ingress (Dziurzynski and Wasilewski, 2012), and coupled Linear Network CFD algorithms (Wedding 2014). In a project sponsored by the National Institute for Occupational Safety and Health (NIOSH), CSM researchers are using Fluent®, a CFD software package by ANSYS, Inc., to model gas compositions and flows in underground longwall gobs. Figure 1 shows a progressively sealed gob with a U-type ventilation system in a three entry development. As the longwall advances, seals are constructed along the headgate in the crosscuts between the center entry and the gob. Additional gob isolation seals are built to block off the headgate entries inby the face. Nitrogen is injected through the seals in the first two crosscuts on the headgate side and at the first crosscut inby the face on the tailgate side, as shown in Figure 1."

Jan 1, 2015

By J. A. Organiscak

Enclosed cab filtration systems are typically used on mobile mining equipment to reduce miners? exposure to airborne dusts and diesel particulates generated during mining operations. Various filter configurations can be used within the heating, ventilation, and air conditioning (HVAC) systems of cabs to remove the airborne contaminants. The air cleaning performance of cab filtration systems is highly dependent on the efficiency of the air filters, the number of filters used, and their placement within the HVAC system. This paper shows how to mathematically model cab filtration systems and illustrates a methodology for developing other cab filtration system design models. Node diagrams of several filtration system circuits are illustrated with their mathematical models at steady state airflow and concentration conditions. Laboratory and field data are presented to demonstrate the validity and utility of modeling enclosed cab air cleaning performance. The paper concludes that incorporating multiple filters throughout the HVAC system improves the air cleaning performance and robustness of the cab filtration system design.

Feb 23, 2014

By T. Emery, D. Sweet, J. Bourgeois, B. Seymour, D. Porter

Cemented rockfill (CRF) is being used to backfill primary and secondary stopes at the Eagle Mine, an underground nickel and copper mine operated by Lundin Mining. National Institute for Occupational Safety and Health (NIOSH) researchers from the Spokane Mining Research Division (SMRD) are conducting cooperative research with the mine staff to determine if the size of a CRF sample affects its measured strength properties. Based on previous research by NIOSH, cylindrical samples of CRF ranging in size from six to eighteen inches in diameter were cast at the mine and cured underground. The samples were later transported to the SMRD laboratory and the Michigan Technological University where tests were conducted to determine the strength and elastic properties of the CRF. To further analyze the relationship between backfill density and compressive strength, different ASTM International compaction techniques were used to cast the samples. For comparison, tests were also conducted on in-situ core samples that were drilled from a stope which had been backfilled with the same CRF mix. The data collected from this study not only improves our understanding of CRF in-situ properties but also helps optimize Quality Assurance/Quality Control (QA/QC) methods for backfill preparation and testing.

Feb 1, 2023

By Louis M. Schlesinger

KMG Minerals, Inc., a mica-feldspar-quartz producer in Kings Mountain, N.C., uses about 50% of its plant's -200 mesh slimes to manufacture brick. However, the company is unable to market the remaining 50% of this fine mineral mixture. The NCSU Minerals Research Laboratory operated a pilot plant to process these slimes to produce an additional product. The process, consisting of blunging and hydraulic sizing, was designed to separate a kaolin-enriched -270 mesh product from the bulk of the coarser +270 mesh "grit" minerals. Size analysis showed that this product was 80% finer than 20 microns and 50% finer than 6 microns (in equivalent spherical diameter). An evaluation indicated that it is a hydrous aluminum silicate that might be suitable in the filler and extender markets for traffic paint, some types of plastics, joint cements, and dusting compounds. Because of its high viscosity, it will be difficult to use more than a small percentage in cast ceramic bodies. However, it might be possible to use up to 10% in extruded ceramic bodies (i.e., electrical porcelain). The 15.2 cm (6 in,) diameter Linatex Hydrosizer was tested using a range of teeter water flowrates, so that the net rise velocity was varied from 0.10 cm/s to 0.40 cm/s. The solid feed rate to the sizer was maintained at approximately 1.1 t/hr/m2 (0.12 ton/hr/ft2). Tests were run using both "shallow" (i.e., 6 in.) and "deep" (i.e., 15 in. teetered beds. The best overall result was obtained when the sizer was operated with the "deep" teeter bed and a net rise velocity of 0.10 cm/s. About 97% of the +270 mesh material was rejected and approximately 79% of the -270 mesh material was recovered in a 14% solids slurry.

Jan 1, 1994

By Vincent T. Ricca

Acid mine drainage is a serious water pollution problem, for its contaminants will eventually effect the quality of the receiving streams. According to the Appalachian Regional Commission (1969)1, 10, 500 miles of streams have been polluted by mine drainage, and 70 percent of this acid pollution is accounted for by underground mines. Due to the severe damage to aquatic life, to recreational and industrial use, and to domestic water supply, more stringent mining and anti-pollution laws have been legislated and coal mine operators are required to treat the mine water discharges to meet the minimum standards. For years now, abatement and treatment methods have been extensively studied. Progress reports presented in the Fourth Symposium on Coal Mine Drainage Research, 1972 1 suggest that a thorough investigation and understanding of the basin discharge is necessary in order to cope with the mine drainage problem. The extent of mine water discharge contamination can be considered as a function of the basin streamflow and acid generation load.' A conservative treatment cost estimation these days is $0.40 per 1, 000 gallons for water with 100 ppm iron, 500 ppm acidity. These figures need not include collection and pumping costs nor the cost of dispersing of chemical waste by-products. To achieve optimal abatement and treatment of mine drainage, predictions of the quantity and quality of mine water discharges are needed. Basin discharge is a continuous process and it can be considered as a. macro-system. This system can be subdivided into micro-systems to describe the various mine discharge .types in the basin. The mining activities could produce acid water discharges from deep mines, stripmines, or associated gob piles. A total study entitled ?Resource Allocation to Optimize Mining Pollution Abatement Programs?* will consider all of these sources. However, this paper will discuss only one micro-system, the drift (deep) mine type. We will look at a single mine and its watershed. The total research project considers a multiple mining complex in an extensive stream basin.

Jan 1, 1973

By T. Grounds, K. Singh, W. R. Reed, R. Cross, G. Ross, S. Klima, M. Shahan

"A 2nd generation roof bolter canopy air curtain (CAC) design was tested by National Institute for Occupational Safety and Health (NIOSH) at a Midwestern underground coal mine. During the study, the roof bolter never operated downwind of the continuous miner. Using a combination of personal Data Rams (pDR) and gravimetric samplers, the dust control efficiency of the roof bolter CAC was ascertained. Performance evaluation was determined using three methods: (1) comparing roof bolter operator concentrations underneath the CAC to roof bolter concentrations outside the CAC, (2) comparing roof bolter operator concentrations underneath the CAC to the concentrations at the rear of the bolter, and finally, (3) using the gravimetric data directly underneath the CAC to correct roof bolter operator concentrations underneath the CAC and comparing them to the concentrations at the rear of the bolter. Method 1 dust control efficiencies ranged from -53.9% to 60.4%. Method 2 efficiencies ranged from -150.5% to 52.2%, and Method 3 efficiencies ranged from 40.7% to 91%. Reasons for negative and low dust control efficiencies are provided in this paper and include: incorrect sampling locations, large distance between CAC and operator, and contamination of intake air from line curtain. Low dust concentrations encountered during the testing made it difficult to discern whether differences in concentrations were due to the CAC or due to variances inherent in experimental dust measurement. However, the analyses, especially the Method 3 analysis, show that the CAC can be an effective dust control device. INTRODUCTION Canopy air curtains (CAC) have been shown to be an effective respirable coal mine dust control for roof bolters in a laboratory setting with dust control efficiencies ranging from 14% up to 75% [Goodman and Organiscak 2001, Listak and Beck 2012, Reed et al. 2017]. Unfortunately, there is limited information on their effectiveness for controlling respirable coal mine dust in the field. On continuous miners, CAC dust control efficiencies ranged from 23% to 69% [Krisko 1975]. Two underground tests of the CAC on roof bolters demonstrated dust control efficiencies of 35% and 53% [Listak and Beck 2012] before problems occurred with operation of the CAC. Since the implementation of the new respirable coal mine dust limit from 2.0 mg/m3 to 1.5 mg/m3 (Code of Federal Regulations, 30 CFR 70.100, 2015), roof bolter CACs are becoming more commonplace in underground coal mines as a dust control tool to prevent roof bolter operator overexposure to respirable coal mine dust. J.H. Fletcher & Co. has been instrumental in delivering an effective design which incorporates the filter, blower, and canopy plenum seamlessly into the design of the roof bolter, resulting in a successful operational roof bolter CAC."

Jan 1, 2018

By Felicia F. Peng

The plant data were collected from three streams around a dense medium drum for coarse coal cleaning operated at various volumetric ratio of medium-to-feed. The effect of the volumetric ratio of medium-to-feed (MF) and particle sizes on the performance criteria, g50 and Ep, of the dense medium drum. These measured data were adjusted and calculated for the yields and balanced relative density distributions by mass balanced method based on the statistic principle. These balanced data were then used to formulate the mathematical models of the separation distribution curves for the various feed size intervals. The correlation equations for the g50 and Ep as the function of inverse of the feed size, and MF and total throughput were established. A numerical algorithm utilizing the Secant method, based on the root searching principle, was developed for yield optimization and simulation of dense medium drum separation to improve the separation efficiency and hence the product yield. The relationships between the direct ash content and relative density of the particles in feed and the products were established and incorporated into the numerical algorithm for predicting the product quality.

Jan 1, 1996

By Michael Murphy, Mark Van Dyke, VASU GANGRADE, Brent Slaker

Room-and-pillar mining in multi-level underground stone mines come with unique pillar stability issues. The pillar stability in these mines primarily depends on the thickness of interburden between mining levels and the staggering of pillars. NIOSH has previously established pillar design guidelines for shallow, flat-lying mines and single-level operations, but there is little guidance for ground control design in multiple-level stone mines. Therefore, to improve the overall understanding of ground control in these mines, a microseismic monitoring system has been installed at a multi-level underground stone mine in Tennessee with up to a 243-m overburden and a 7-m interburden thickness between levels. The microseismic system is comprised of nine uniaxial accelerometers and one triaxial accelerometer installed in the interburden. The seismic array is locally focused with all sensors installed within a 625 m2 area and is setup to monitor the seismicity around the formation of the pillar in the lower mining level. Data is collected over 11 months and comprises of over 1,000 high-confidence events that have been located in the study area comprised of post-blast activity. The event locations were identified using a 3D-velocity model, with an average 4-m location accuracy for this array calculated using the system data. Most observed seismicity was on the excavation boundary, both in the interburden and in the roof of the top level. At this stage of analysis, there are no significant rock failures with which to correlate seismicity, but event locations correlate well with presumed damage in the vicinity of blasts.

Apr 26, 2022