Search Documents

By Erika Moonin, Jim Nickerson, Marcus Jensen

"This paper will explain how the Contractor and Owner avoided a contractual dispute involving characterization, impacts, and final remedy for challenging ground conditions encountered during drill and blast excavation of the starter tunnel required for launch of the tunnel boring machine (TBM). During excavation more than 600 feet underground, the Contractor encountered a large complex fault zone subject to more than 14 bar of water pressure. Successive ground inflows from the fault complex over a six-month period presented significant technical and partnership challenges for the team and ultimately delayed the project by nearly one year. This paper will discuss how the Contractor, Owner, and their respective consultants worked together to address these challenges, make decisions, and ultimately move the project to successful completion. PROJECT BACKGROUND AND NEED Seven states of the western United States of America rely heavily on the Colorado River and its tributaries for their water supply. The primary source of water for the Colorado River is winter snow that falls in the mountains ringing the Colorado River basin, including the Rocky Mountains, the Wind River Mountains, and the Uinta Mountains. Flows in the Colorado River vary significantly from year to year, depending on the amount of snow and rain deposited in the basin. During the 1980s and 1990s, snowfall was relatively abundant and Colorado River flows were high on average. Beginning in the year 2000 and continuing to the present day, snowfall has been well below documented historical averages and Colorado River flows have diminished. In fact, a trend toward diminishing flows is evident during the period of the historical record. This variability in Colorado River flows and the trend to lower flows is represented in the following Figure 1."

Jan 1, 2016

By Camilo Quintero, Frank Cesario, John Kinnear, Brian Boye

In this paper, an innovative approach was adopted to automatically calculate the effects of tunnel induced settlement on buildings and utilities. The approach resulted in increased output quality, consistency, reduced time, cost savings and a greater ability to respond quickly to design changes. The techniques described have been applied to the Fairbank Silverthorn Storm Trunk Sewer System project, located within the City of Toronto. The automation allowed a very large area of topography, tunnels (6 km), buildings (9000) and utilities (over 1000) to be rapidly evaluated. Visualization of the settlements and impacts also allowed the project design team to optimize the system design to mitigate the settlement impacts.

Jun 13, 2021

By Yuanhong Qi, Xun Fu Wang, Tao Fu, Kunkun Cui, Yingyi Zhang, Jie Wang, Junmao Qie

With the sharp decrease of sulfide nickel resources, the nickel laterite is becoming more attractive as nickel oxide, nickel matte, and nickel-iron. This study investigated the mineral phase structure, chemical analysis, thermal properties, and element distribution characteristics of the rotten rock layer deposited in the Southeast Sulawesi Ophiolite Belt. The results show that the nickel laterite deposited in Southeast Sulawesi Island, Indonesia, belongs to the typical high-nickel and low-iron garnierite-type laterite. The concentrations of nickel and iron of the nickel laterite are 1.99 wt% and 17.55 wt%, respectively. The serpentine, olivine, clay, chlorite, hematite, and magnetite are the major minerals, and the pyroxene, actinolite, limonite, and chromite are the minor minerals in the nickel laterite in Southeast Sulawesi, Indonesia. Serpentine and olivine are the main nickel minerals with an average nickel concentration of 3.65 wt% and 1.73 wt%, respectively. The Fe and Ni have homogeneity and symbiosis in the serpentine and olivine, and their concentrations are often positively correlated.

By M. Dayne Aldridge

A discussion of the definition of automation in mine ventilation applications is presented. The results of theoretical studies, experiments and practical experience from work in the United Kingdom, Belgium, Poland, the Soviet Union and the United States are summarized. Conclusions are drawn from these efforts and the prospects for the future development of automatic mine ventilation systems are explored.

Jan 1, 1978

By H. Kinilakodi, R. L. Grayson

In 2010, the U.S. Mine Safety and Health Administration (MSHA) began holding hearings on a new coal mine respirable dust rule, which proposed a 1.0 mg/m3 standard, a separate 0.1 mg/m3 quartz standard, and the use of single-shift samples for compliance. Small mines largely comprise the “hot spots” where dust diseases of the lungs increased dramatically over the past decade. This paper presents findings on the feasibility of small mines’ compliance with the proposed new 1.0 mg/m3 standard. It gives probabilities of noncompliance by MSHA district, average mining height and selected “hot spot” counties. Because silicosis and respirable quartz dust appear to be the primary issues related to a recent doubling of the prevalence of dust diseases of the lungs, multiple regression models for prediction of the average total quartz content of compliance samples are given. These findings have significant implications for the need for better dust control methods.

Jan 1, 2012

By Richard E. Otoo, Evan J. Owen, Virginia T. McLemore

According to the U.S. Geological Survey (USGS), a critical mineral is one that is essential to the economic well -being of a nation and whose supply may be disrupted due to geological, geopolitical or environmental factors (Nassar et al., 2020). For example, REEs are critical to the production of electricvehicle motors as well as wind turbines, yet China’s share of their global production rose to more than 95 percent in 2010 (IEA, 2021). China’s share has since declined, with production quotas dropping to nearly 70 percent by 2023 (Statista, 2023). This and similar situations with many of the critical minerals raise deep global concerns about supply-chain vulnerabilities (Bauer et al., 2011). Critical minerals are used in the production of renewable energy, electronics, agricultural products and common household items (McLemore, 2020). As the global demand for these minerals continues to grow, it is not sufficient to rely solely on scaling up production from existing operations. While increasing production from known deposits can provide short-term relief, long-term resource security requires discovering new, economically viable mineral resources. One of the most effective ways to secure future supply is through mineral exploration, which increases the global inventory of critical minerals and also minimizes risks posed by market monopolies and political instability. The major challenge of mineral exploration lies not only in identifying mineralized deposits but also in determining whether discovered concentrations are sufficient to warrant further investigation and development. A fundamental concept in this decision-making process is using cut-off grade. In this article, cut-off grade refers to the minimum concentration of minerals required to justify further exploration efforts based on factors such as type and size of mineral deposit, mining and processing technologies, associated byproducts/coproducts and the market price of these minerals. Typically, economic cut-off grades are used to determine whether a mineral deposit can be mined profitably. However, this article focuses on preliminary cut-off grades needed to establish whether the amounts of critical minerals within a deposit are high enough to justify further exploration and detailed evaluations. By comparing mineral deposit grades, size, production and extraction technology, and other economic factors with established and active mines, exploration teams can estimate cut-off grades that justify further exploration.

Aug 1, 2025

By Bruce Watzman

"Few issues are more important to the National Mining Association (NMA), the U.S. mining industry and NMA’s MINExpo International 2016 exhibitors than safety.Global mining safety and health is a journey necessitating continuous improvement, collaboration and innovation on the part of both mining operators and their suppliers.MINExpo 2016, which takes place Sept. 26- 28, 2016, in Las Vegas, provides attendees with the opportunity to view technologies to help refine management of mining safety and health, utilizing NMA’s CORESafety system. CORESafety ‘One of the best’Launched by NMA in 2011 and moving forward ever since, CORESafety is driving continuous improvement in safety and health performance among participating industry companies by shifting from a command-andcontrol regulatory approach to a risk-based systems approach built on the Plan-Do-Check-Act model (Fig. 1).Considered an exemplary safety and health management system, NMA’s CORESafety system helps mining operators change their approach to safety and health management by enhancing the safety and health culture throughout their organizations. Although it is challenging to consistently and completely control all the factors and variables occurring in daily mining operations, experience has shown that applying systematic controls to as many variables as possible is the most successful approach for improvement in mining safety and health.When embarking upon the development of the CORESafety framework, NMA’s leadership set an ambitious goal to eliminate fatalities and reduce the injury rate 50 percent in five years, or the “0-50-5” goal. While the goal has not been met yet, the steady progress has been extraordinary with fatalities among participating companies dropping 45 percent during the period 2011-2015 (Fig. 2). Data also demonstrate that, as participating companies increase their level of implementation, total injury rates have also declined (Fig. 3).In a September 2015 interview with NMA, Penn State University mining engineering Professor Jeffrey Kohler praised CORESafety as “an inspired and timely program that brings together key elements to achieve safety and health goals.”"

Sep 1, 2016

By Robert B. Crookston

This paper presents a resume and status report: of mining technology appropriate to commercial oil shale development in the United States today. The nature and extent of oil shale in Colorado and Utah are discussed. A look at most of the prominent activities now underway emphasizes the questions "where are we now?" and "where are we going?" Various alternate mining methods are reviewed and a bibliography of oil shale mining is included.

Jan 1, 1980

By P. B. Queneau

An operating problem encountered at the Moa Bay operation in Cuba, where nickeliferous laterite ore is processed by sulfuric acid pressure leaching, is the formation of alunite and hematite deposits on the autoclave walls. The AMPX Extractive Research & Development, Inc., metallurgical laboratory (Golden, Colorado) has made substantial improvements in the Moa Bay process in the areas of metal recovery, energy consumption, and feed versatility. One of the advantages of AMAX's process is its ability to treat substantial portions of nickel- and magnesium-rich serpentine while maintaining acid utilization efficiency. The process minimizes scale formation by combining staged acid addition with vigorous agitation and 270°C operation, but does not eliminate scaling. This paper describes how advantage can be taken of MgSO4?XH20 precipitation both to inhibit alunite scaling and to disperse hematite scale within the MgSO4?XH20 matrix. Cooling the autoclave from its 270°C operating temperature down to 180°C takes advantage of the reverse solubility of magnesium sulfate. The magnesium dissolves, liberating entrained hematite, thus providing a means for control of autoclave scale with minimum process disruption.

Jan 1, 1984

By Roe-Hoan Yoon, Kaiwu Huang

Derjaguin and Dukhin (1961) were the first to develop a model for bubble-particle interaction in flotation from first principles by considering the surface forces in wetting (or flotation) films. The model predicted that the energy barriers to bubble-particle attachment arise from the ζ-potentials of fine particles, which corroborates well with an earlier work of Fuerstenau (1957) reported for the flotation of quartz using dodecyl ammonium acetate (DAA) as collector. In the present work, a series of surface force measurements have been conducted by accurately monitoring the changes in bubble curvature during bubble-silica surface interactions. The curvature changes are then used to determine the capillary force, which is the sum of the hydrodynamic and surface forces. By subtracting the former that can also be determined from the curvature changes, one obtains the surface forces (or disjoining pressure). The results obtained as functions of pH and collector concentrations show that control of the ζ-potentials of bubbles relative to those of the silica surfaces is critical for maximizing the negative disjoining pressure, which is conducive to promoting bubble-particle attachment in flotation.

By Willard A. Murray

Investigations of underground coal gasification (UCG) have been actively pursued by the U.S. Department of Energy since the early 1970s; the Lawrence Livermore National Laboratory (LLNL) conducted its first field experiment in 1976. In conjunction with field and laboratory studies of the process of recovering energy in the form of combustible gases from the burning of coal deposits in situ, an extensive environmental program has been conducted at LLNL under the auspices of both the U.S Department of Energy and the U.S. Environmental Protection Agency. This program has focused on groundwater contamination and ground surface subsidence caused by UCG. The material presented in this paper is a summary of results from the environmental studies of UCG activities conducted by LLNL as described by Mead, et al. (1981) and supplemented by the author's experience with this program in 1980 and 1981. The following sections describe specific groundwater contamination and surf ace subsidence problems encountered during field experiments in northeastern Wyoming, and will discuss implications of preliminary findings from geohydrological investigations of a site in southwestern Washington. Finally, possible environmental control technologies that are most likely to be effective in mitigating environmental impacts are discussed.

Jan 1, 1982

By C. Bazin

The fundamental error associated to the sampling of heterogeneous ore particles is unavoidable and can only be minimized by an adequate selection of the sample mass and/or size reduction of the sample before division into sub samples for testing or assaying. The preparation of ore batches to carry out the mineral processing evaluation of an ore is a sampling process. The fundamental error associated with the division of the ore into batches is responsible for the differences in the composition of the batches. This paper attempts by various means to assess the reproducibility of the gold content of test batches prepared from a gold ore sample. The results of the investigation shows that for fine gold grain sizes the variability in the composition of the batches is less than that predicted by Gy?s formula and that the gold grain size is a strategic information in the assessment of the gold content variability of test batches.

Feb 23, 2014

By A. Hajati

The main purpose of this study was to find the optimum values for factors affecting the Zn recovery rate using oxine or dithizone as a chelating agent collector during flotation in a Hallimond tube. Eight control factors, including four levels of pH, oxine/dithizone, corn starch, sodium thiosulfate, sodium citrate, sodium silicate, conditioning and floating durations were considered in a Taguchi experimental design technique. An L32 orthogonal array was applied to determine the signal-to-noise (S/N) ratio. Analysis of variance (ANOVA) was used to determine the optimum conditions and the most significant parameters affecting the reaction rate. Analysis of the experiments using the Taguchi approach indicated that pH had the highest contribution to the recovery rate of zinc oxide particles. The results showed that the recovery rate of zinc increased by 43.4 ± 3.0% and 24.9 ± 3.2% using oxine and dithizone, respectively, under optimum conditions with a confidence level of 90%.

Jan 1, 2010

By M. Z. Rashad

The purpose of this paper was to compare the covariance and multiquadric functions in same mining and geological applications. The basic principals of the two techniques are covered briefly. Similarities and dissimilarities of the covariance and multiquadric functions are discussed geometrically, mathematically and practically. A 14 by 16 kilometer square area in Baharia Oasis, Western Desert of Egypt, was selected for a detailed comparative test. The gravity anomalies of forty-eight test stations were computed by using the data of sixty-three control stations. The results indicated that the covariance function is quite better than the multiquadric one. On the other hand, the multiquadric function more simple in computation than the other one, which needs to precalculations such as semivariogram and covariogram. Moreover, multiquadric equations are based on geometrical and physical considerations rather than covariance functions.

Jan 1, 1990

By H. Melama

The primary grinding stage in the Vuonos concentrator comprises a rod mill in open circuit and a semi-autogeneous mill in closed, circuit with a hydrocyclone classifier. The instrumentation of the grinding circuit is displayed in Fig. 1. All the measurements have computer interfaces and all the control circuits have been implemented by the process control computer. The crushed ore feed to the rod mill is measured by a belt-weigher and controlled by a belt-feeder. The pulp density in the rod mill is stabilized by proportioning the waterfeed at the mill inlet to the crushed ore feed. The slurry level in the pump sump is measured by a pressure transducer and it is controlled by charging the speed of the direct-current drive pump.

Jan 1, 1984

By J. Gustavson, E. Mallard, F. Pirkle

The Sales Comparison Approach to estimating the value of a mineral property must always be attempted1 . In addition to other parameters, the approach depends heavily on the availability of transaction data. The consideration for the mineral property must be in form of cash, cash equivalent or other consideration. In other words, “What dollar amount did the property sell for?” Mineral properties are generally real estate, albeit frequently buried deeply under the overlying surface real estate, unless the property may be a quarry. In some states, transactions must be recorded in county courthouses, and the sale consideration must be included. In such cases, the appraiser’s job is made easy. In other locations, the sale considerations are withheld in the courthouse data; but occasionally a local transfer tax is collected and recorded. Again, the appraiser’s job is made easy by back calculation with knowledge of the legislated transfer tax percentage. The worst problem occurs when the consideration for a mineral real estate sale is totally withheld. That may occur in so-called nondisclosure states. A recent map2 of ten non-disclosure states in red is shown below. For the full color code, please refer to the footnote

Mar 2, 2022

By R. Scheffel, R. Washnock, G. Zarate

"The second survey of global copper leaching operations has been completed, the data published in 1998 has been updated. A survey questionnaire was sent to 40 identified copper leach operations around the world including those leach properties still in operation that responded to the 1998 survey. This paper lists the results of 26 operations that responded to the survey. Selected information from the survey is represented in graphical form. INTRODUCTION Copper leaching was first performed by truck dumping huge monolithic stockpiles of ore and flooding the surface with leach solution or lixiviant with little understanding to the parameters that support optimum recovery of the metal. Heap leaching has evolved into a controlled process whereby a complex low grade ore is stacked in shallow lifts (under 10 m in most cases). The ore is usually crushed and agglomerated, conveyor stacked on an engineered containment system (leach pad) and irrigated in a controlled manner. The lixiviant chemistry is designed to extract the optimum amount of metal from the ore. At first glance, heap leaching appears to be simple in nature. In fact, it is a very complex process. A plethora of technologies such as material handling, environmental control, analytical techniques, solution chemistry, hydrology and many others contribute to the design and operation of a heap leach. Heap leaching requires an inter-disciplinary approach between geologists, mining engineers and metallurgists. Many operational factors affect heap leaching. The process must address climatic factors, flexible operation, quality control before and after leaching, physical characteristics of the ore, geology, mineralogy, reagent consumption, solution application rate and methods (wobblers or emitters), particle size, and favorable conditions for bacterial growth and survival. Predicting, troubleshooting, and optimization of leach recovery is a significant challenge when considering the number of variables involved and their interactions The survey updates many of these key operating parameters to the current state of the art. It should provide the reader an excellent benchmarking summary of these factors on a site-by-site basis."

Jan 1, 2016

By E. T. Tuzcu

Microscale information about single particle fracture can be incorporated into the macroscale model of the whole size reduction process in the mill. The ultrafast load cell (UFLC) device provides a substantial amount of information about fracture characteristics of a particle under impact loading. UFLC captures high-resolution compressive force signals during particle breakage. The measurement of the compressive force at the instant of fracture of the particle allows computation of a number of comminution-related particle properties, as well as the energy absorbed during fracture. In the current study, limestone particles 50 mm in size were fractured to obtain specific fracture energies. Then, based on the experimental data, two models were proposed to quantify the fracture process. The specific fracture energy distribution of the particles in the range of 6 to 50 mm was defined by the well-known Weibull distribution. The other model is a probabilistic fracture model. This model is a link between energy events occurring in a grinding mill and the breakage rates of particles. The impact energy spectra or energy events occurring in a grinding mill can be obtained with a discrete element method (DEM) simulation. One can model the breakage rates of the mill material by combining the energy spectra with the probabilistic fracture model. This novel approach for the modeling of breakage rates via DEM and UFLC is shown here.

Jan 1, 2011

By N. Moelans, I. Bellemans, K. Verbeken

Metallic droplets can remain attached to solid particles within liquid slags, resulting in production losses in several movement of solid particles in the liquid slag in a system, considering the attachment of liquid metal droplets to solid slag and on the resulting microstructures is investigated as a function of the velocity of the particles. For all wetting For the amount of metal attached to the particle, a clear trade-off was found between the speed of motion of the solid particle and the wetting regime.

By James M. Barker

The occurrence of borates and zeolites at Mesa del Alamo is well documented by McAnulty and Hoffer (1) and Lefond and Barker (2). Further investigation indicates the presence of priceite and meyerhofferite in addition to the howlite (1) and colemanite (2). Analcime occurs in addition to the clinoptilolite and phillipsite (2). The Mesa del Alamo area is about 200 !a south of Tucson, Arizona, and 13 km southeast of Magdalena, Sonora, Mexico, just south of the unpaved road to Cucurpe (Figure 1). The geology and mineralogy of northcentral Sonora is known only on a regional basis except for small areas mapped in detail during copper exploration. The study area is within the Basin and Range province of North America from which borates and zeolites are now produced in California. The borates and zeolites at Mesa del Alamo occur in geological environments similar to those of the Mojave and Death Valley regions of California (3, 4). Thus, a detailed exploration pro- gram in the Magdalena area could result in the discovery of economic borate and/or zeolite deposits.

Jan 1, 1979