Search Documents

By Simón Díaz‑Quezada, Ernesto Arancibia, HUMBERTO ESTAY, Tomás Vargas

In situ leaching (ISL) is an attractive technique that enables copper recovery from copper oxide ores that are either low-grade or located at depths too great to be economically exploited through conventional methods. At present, in situ leaching (ISL) has been applied to intact copper oxide ores, in particular, those which (i) present a good natural permeability and (ii) do not require preconditioning. Many copper oxide ores present low natural permeability. These are located above the water table and need preconditioning for the ISL application. The present work shows an economic assessment of the application of ISL to this type of copper ores. The preconditioning technique considered here involves the application of partial mining by sublevel stoping by removing a small fraction of the ore. This technique results in forming an ore bed with good permeability and good solution collection at the stope base. The economic assessment of this approach suggests that it can be implemented with positive net present values to copper oxide ores located at depths in the 100–300 m range, with copper grades above 0.4%. The maximum acid consumption values are below 52.5 kg/t, with blasting procedures designed to produce an ore bed with an average particle size below 6″. The breakdown of operational costs indicates that the mining cost is still very high, accounting for up to 60% of the total operating costs. Therefore, optimizing mining procedures is still necessary for improving the economic outlook of this approach and thus expanding the application field of ISL.

Feb 4, 2023

By Kenneth J. Edmiston

The objectives of this paper are: to review the current status of chloride leach processes for sulfide concentrates, to make an evaluation as to the applicability of chloride leaching for replacing pyrometallurgical processes and to comment on recent advances in construction materials. The paper does not delve in detail on process chemistry. Sufficient references are presented on each process to allow the interested researcher to obtain process chemistry details. GENERAL The fact that chloride oxidates can solubilize base metals from sulfide concentrates has been known since the 1880's. The work of Hoepfner in 1902 was particularly accurate for its time with regard to the chemistry of chloride solutions. Recent work has dealt with the understanding of chloride extraction thermodynamics by modelling the behavior of metal chloride complexes. In the last several years several excellent review articles and symposiums have been issued covering chloride chemistry (1 thru 6).

Jan 1, 1984

By BHAMIDIPATI S. SASTRY, SRIVATSAN J. SRIDHARAN

Pressure losses in mine ventilation systems are estimated using friction factors and shock loss factors. The efficient planning and designing ofmine ventilation systems depend on the accuracy of the friction factors as well as the shock loss factors that are taken into consideration. While there is a much more acceptable knowledge of what constitutes friction loss in mine roadways, the shock loss factors are in general readily not available for all possible contexts of flow separation phenomena in mines. One such special case of shock loss in mines is the train of mine cars in the airway. Mine cars are widely used for the transportation of material, and the information on shock loss factor for mine cars is limited. This paper examines the pressure loss occurring due to a train of mine cars in an airway using scale model studies and numerical investigations. Computational fluid dynamic (CFD) studies are conducted using four different turbulence models. The performance of different turbulence models is analyzed by comparing it with the experimental results. The study suggests that the boundary layer resolution method is significant in the simulation of shock loss. From the study, it is found that the shock loss factors from presently available model overestimate the pressure loss by 7 to 15 times. A better prediction model for the shock loss factor of a train of mine cars in the airway is proposed using the experimental results.

Jul 24, 2020

By M. Bai

The influence of mining on the hydro-geomechanical environment is greatly constrained by alternating mining geometries. The limiting magnitudes of surface subsidence and groundwater flow over the mining area, as a result of geometry changes, can be reasonably predicted through a coupled finite-element model introduced in this paper. Verification of the model has been tested using real and conceptual case studies which reveal that changes in strata conductivities are strongly related to the strata deformation induced by mining. The greatest modification of hydraulic conductivities occurs within the caving or severely fractured zones. The study indicates that narrowing the panel face width will substantially reduce both the intensity and extent of mining damage to the overlying strata, limit surface subsidence and constrain the change in hydraulic conductivity to a reduced scale and smaller extent, particularly as mining depth increases.

Jan 1, 1993

By G. T. Lineberry

Horsepower requirement is recognized as a most important equipment characteristic. Other critical equipment characteristics will be isolated and analyzed by traditional operations research techniques, using off-highway trucks as an archetype. A computer search technique has been developed, employing various production and cost analyses. With this model, the optimum combination of horsepower, capacity, and velocity can be found, minimizing handling cost per ton. An example of the program's use and interpretation of its results will conclude the paper.

Jan 1, 1984

By D. Parks, A. Miller, M. McNinch, R. Jacksha

Each year, hundreds of mine workers are involved in machinery-related accidents. Many of these accidents involve inadequate or improper use of lockout/tagout (LOTO) procedures. To mitigate the occurrence of these accidents, new safety methods are needed to monitor access to hazardous areas around operating machinery, improve documentation/monitoring of maintenance that requires shutdown of the machinery, and prevent unexpected startup or movement during machine maintenance activities. The National Institute for Occupational Safety and Health (NIOSH) is currently researching the application of Internet of Things (IoT) technologies to provide intelligent machine monitoring as part of a comprehensive LOTO program. This paper introduces NIOSH’s two phase implementation of an IoT-based intelligent machine monitoring system. Phase one is the installation of a proof-of-concept system at a concrete batch plant, while phase two involves scaling up the system to include additional sensors, more detailed safety/performance metrics, proximity detection, and predictive failure analysis.

By Josh B. Taggart

Some twenty to twenty-five years ago we saw the beginning of mechanization in our coal mines, It has now progressed to the point Chat as instruments of production the pick and shovel are things of the past, They had to give way to better and more efficient methods--so mechanization, followed by and combined with automation, has become common-place in our mines. Our coal could not keep its competitive position without this progress Without it our industry could not look to the future with any degress of confidence. Today we lock back and see cases of regained and salvaged markets. We see better coal products being produced at decreasing costs. We see better utilization of manpower and a stronger, more confident industry, Our hats arc off to those mining men, equipment manufacturers, labor leaders, and others who had the foresight to work toward these ends and the ability to bring them about.

Jan 1, 1962

By J. J. Sense

The Mission Unit of American Smelting and 'Refining Company is located in Pima County, Arizona, approximately twenty miles southwest of the City of Tucson. The Unit consists of an open pit copper mine and concentrator. The concentrate is shipped by rail to Company Smelters at Hayden, Arizona, or El Paso, Texas Mine stripping began at Mission in the fall of 1959, and construction of the 15,000 tons per day concentrator gas started in the spring of 1960, The first ore was treated in mid summer of 1961 and full ore production was reached in August of 1961. At that time over 46,000,000 tons of material had been moved from the pit. Current production (ore and waste) averages over 100,000 tons per day. Total production to date (ore and waste) over 120,000,000 tons.

Jan 1, 1964

By D. N. Trerice

The Electric Power Research Institute (EPRI) is sponsoring the construction and operation of a coal cleaning test facility at Homer City, Pennsylvania. The facility represents a major investment by the electric utility industry to advance the state of the art of conventional coal cleaning technology. The facility is unique in design and can process large quantities of coal in conventional flowsheet configurations, simulate full size plant conditions, and perform open and closed loop performance testing on conventional and advanced coal cleaning equipment. Computer operation will also be demonstrated. The facility objectives, initial complement, and operating plane are discussed as they relate to other coal cleaning projects at EPRI.

Jan 1, 1981

By Brendan Demich, Joseph McGuire, Emily J. Haas

Near misses recorded and reported by workers can provide awarenessto the potential causes of injury and prompt safety management initiatives. Although most companies require near-miss reporting, it is unclear what the value of these reports are, if any, and how they influence subsequent actions or controls to reduce on-the-job risks. Researchers at the National Institute for Occupational Safety and Health (NIOSH) conducted a case study with an aggregates company in which near-miss reports were analyzed at each of their locations over an entire quarter during the summer of 2018. Within that quarter, workers recorded 249 near misses. Of those, 167 were valid near misses that occurred at work. Researchers coded the reports using a qualitative 5 × 5 risk matrix. Of the 167 near misses, 19% were deemed low risk, 25% moderate risk, 30% high risk, and 26% critical risk. Several patterns in the near-miss incidents were documented, including classification of incidents and common corrective actions referenced (i.e., elimination/substitution, engineering control or redesign, work process/procedures, and personal protective equipment). The analysis provides insight into ways that risk communication and management programs can be improved to reengage workers and their situational awareness on the job.

By David R. Maneval

The mining of coal in Alaska receives special treatment in the Surface Mining and Reclamation Act passed by the U.S. Congress in 1977 (PL95-87). Section 708 of the Act required that the National Academy of Sciences (NAS) perform a study of "Surface Coal Mining Conditions in the State of Alaska, In Order to Determine Which, If Any, of the Provisions of the Act Should be Modified with respect to Surface Coal Mining Operations in Alaska'. The special committee on Alaskan Coal Mining and Reclamation of NAS completed their study in 1980 and prepared their report (NAS, 1980). At this time, the Secretary of the Interior and the Congress have taken no special action with regard to either special regulations geared specifically to Alaska or to submitting special draft legislation to the Congress requesting amendment of PL95-87. The Alaska Department of Natural Resources (DNR) has drafted legislation which was submitted to and passed by the 1982 session of the State Legislature. The State regulatory agency has also drafted the requisite regulations necessitated by the amendments to the State's Basic Coal Mining Act. It is expected that by mid 1983 DNR will have applied for "primacy" to the office of Surface Mining, U.S. Department of the Interior (OSM). They will be submitting the amended State Law, the revised State Regulations and an operational plan as called for by OSM regulations. The presumption is that primacy will be granted to the State of Alaska under PL95-87. The Usibelli Coal Mine continues to be the only operational commercial mine for coal in the State of Alaska. It produced 7.26 x 10 kg (8 x 10 " T) of coal during 1981. The current mine was started in 1920 by Captain Lathrop, an early developer and pioneer in Alaska. It was continued by Emil Usibelli and was taken over after the death of E. Usibelli (in the 1964 earthquake) by his son Joseph Usibelli who is the current President of, the firm3 Their latest improvement is a 27.5 m (36 yd. )Bucyrus-Erie Dragline which handles most of the overburden removal. The coal is removed by a loader-truck combination. They are currently starting up the use of a unit train loading facility which handles forty cars every two hours. This loading system was a development necessitated by the Sun Eel Export contract. The Alaskan Railroad was a major cooperator in the development of the first unit train loading facility in Alaska.

Jan 1, 1982

By Gregg W. Davidson, J. Andrew McGlenn, Frank Huber

The Second Narrows Water Supply Tunnel will ensure system reliability in the event of a major earthquake and increase the Greater Vancouver Water District’s capacity to meet the long-term needs of a growing population. The tunnel will be 1,100 m long and 6.5 m in diameter (3,610 LF × 21.3 ft), constructed under Burrard Inlet between North Vancouver and Burnaby in British Columbia. It will be excavated through mixed ground conditions under high groundwater pressure, using a slurry TBM, between a 72 m (236 ft) deep shaft in soil and a 110 m (361 ft) deep shaft in rock. The completed tunnel will accommodate three large-diameter water mains that will be installed as part of the tunnel contract. This paper presents the project from design and contractor procurement, into the current construction stage describing some of the unique challenges encountered during the project development to date.

Jun 13, 2021

By L. M. Kocher, J. R. Heberger, J. P. Pollard, M. F. Nasarwanji

Injuries associated with hands and fingers are highly prevalent in mining and identifying factors associated with these injuries are critical in developing prevention efforts. This study identifies nonfatal injury incidence rates, nature of injury, work activities, glove usage, and sources of hand and finger injuries in the U.S. mining industry, as reported to the Mine Safety and Health Administration (MSHA) from 2011–2017. Hand and finger injuries occur at a rate of 6.53 per 1,000 full-time employees, which is nearly double the rate of the next highest affected body part, the back. Most of the hand and finger injuries were classified as cuts/lacerations/punctures (53%) followed by bone fractures/chips (26%). Materials handling and maintenance/repair were common activities at the time of the incident with miscellaneous metals (pipe, wire, guards) and hand tools as the primary sources of hand and finger injury. Although information on glove use was limited, leather gloves were most often worn when an injury occurred. When worn, gloves were found to contribute to 20% of the injuries, indicating their potential to protect the hands, but also potentially put the hands at risk. Further research is necessary to determine performance requirements for gloves used in mining operations, specifically those offering cut and puncture resistance.

Mar 2, 2022

By Sheridan A. Glen

As the Federal government along with individual states continue to grapple with the job of refining a comprehensive energy policy, coal continually stands out as an energy source which heralds a combination of old and new capabilities like an energy planners prophecy, but which is plagued with serious environmental constraints. To determine what level of coal utilization is ultimately possible for states East of the Mississippi, whose high sulfur content coal presents the most paramount of challenges, one must consider product availability, via existing transportation modes, the developing industrial markets and the ability of coal to meet the challenge of becoming an environmentally acceptable fuel. Gasification is emerging as a form of utilization, which during the next twenty years stands a good chance of being able to meet the challenge of making coal an environmentally clean, easily transport-able and usable fuel. It can be argued that, of all the potential ways of utilizing high sulfur coal, coal gasification is perhaps the most expensive, the most financially risky and carries environmental liabilities of its own. Synthetic gas and oil markets will undeniably be a function of price and demand, which, for the purposes of this paper, I'm assuming will begin to merge in the late 1980's and into the 1990's. This is also presuming that public utility commissions will allow favorable price structure ruling so that gasified coal products can be rolled into their respective rate base, much the same as synthetic natural gas from petroleum by-products are currently being priced. The comparative economic markets of coal to gas pro-duct have plenty of time to mature. There is an approximate twelve-year lead time needed to bring coal gasification plants on line which will be able to compete in the market place for natural gas and oil customers.

Jan 1, 1977

By H. Huang, Y. Takasaki, R. N. Gow

"The presence of enargite (Cu3AsS4) is problematic in gold processing not only because it is environmentally hazardous due to its arsenic content but also because it is refractory, causing both cyanide and oxygen consumption to increase. Selective leaching and treatment of the arsenic would prove advantageous prior to applying conventional gold leaching methods. The reactivity of enargite samples from Butte in Montana and Quiruvilca in Peru were spectroelectrochemically studied under alkaline conditions – pH range of 8-13 – using Raman spectroscopy and cyclic voltammetry. Raman spectra of the surface were collected during and after potentially cycled voltammograms in order to determine and compare surface species against theoretical EH-pH diagrams constructed from mass-balanced thermodynamic calculations using STABCAL software. Under slightly oxidizing conditions, covellite (CuS) peaks were found in a short matter of time, above ~100mV vs. SHE for pH 9-13, suggesting arsenic leaching specifically occurred. At longer conditioning times, elemental sulfur was observed and tended to passivate the surface. The presence of elemental sulfur suggests that copper was eventually leached from the surface. By operating above pH 12, under slightly reducing conditions near -300mV vs. SHE, arsenic can be selectively leached as thioarsenate (AsS4 3-) or thiosulfate (AsO4 3-) without sulfur formation.IntroductionEnvironmental limitations on the pyrometallurgical processing of ores and concentrates bearing arsenic and other hazardous elements often outweigh those in hydrometallurgical processing, particularly when minerals like enargite (Cu3AsS4) are present. The hydrometallurgical processing of enargite-bearing materials can be broken down into two categories: the co-dissolution of arsenic and copper under acidic conditions, and the selective leaching of arsenic under alkaline conditions. The selective leaching of arsenic would preferably leave behind copperrich sulfide phases, typically chalcocite (Cu2S) and covellite (CuS), which then become more amenable to conventional copper (and gold) processing. Furthermore, selective leaching often employs sulfide (S2-), bisulfide (HS-) or polysulfides (Sx 2-) to first extract the arsenic as AsS4 3- and AsS3 3- (Delfini et al., 2003; Anderson and Twidwell, 2008; Tongamp et al., 2010a,b). However, hypochlorite leaching (Viñals et al., 2003; Curreli et al., 2005; Mihajlovic et al., 2007), ammoniacal leaching (Gajam and Raghavan, 1983), and finegrinding to mechanically activate the enargite surface (Balaz and Achimovicova, 2006) have been investigated to increase the normally slow reaction kinetics. Because gold ores are becoming more refractory due to increasing arsenic contents as a result of enargite, these methods are being examined more closely by the gold-mining industry."

Jan 1, 2015

By VIVEK KUMAR HIMANSHU, M. P. Roy, P. K. Singh, A. K. Mishra, RAVI SHANKAR

Blasting with the aim to reduce oversize boulders in underground has many hurdles due to limited accessibilities and poor site conditions. Optimized drilling and blasting parameters can help to achieve this objective. The major challenges of the blast designers lie within deciding blast geometry, namely drill hole diameter, burden, and spacing. The general approaches covered worldwide to determine burden-spacing are based on various rules of thumb, which are based on previous experiences of blasts and the associated outcomes. However, many parameters influencing optimum burden-spacing to achieve desired fragment size are site specific. Sometimes drill geometry is decided based on associated blasting hazards rather than rock fragmentation. The Kuz–Ram model is a worldwide accepted rock fragmentation predictor. The parameters associated with this predictor also include burden-spacing for a blast. Back calculation of burden-spacing from the Kuz–Ram model can be used to achieve desired fragment size. This paper deals with burden-spacing determination by using an empirical approach for the underground stope ring blasting.

Jan 4, 2020

By M. Fan, R. Letkiewicz, A. Hobert, J. Milbourne

Ultrafine copper, gold and silver minerals flotation has become increasingly important because of the rising demand for processing finely disseminated ores. This paper investigates the improved flotation of ultrafine ores from a Troilus Gold project. Troilus is primarily an Au-Cu deposit but contains minor amounts of Ag, Zn and Pb, as well as traces of Bi, Te, and Mo. As a result of ultrafine Cu-Au-Ag dissemination and associated grinding requirements, Eriez’ column/StackCell and Denver benchtop cells were utilized to optimize their respective flotation responses. Enhanced flotation results were achieved using column and StackCell technologies. KAX 51 and SPRI 206 collectors, Na2SO3, and ZnSO4 depressants were the primary reagents employed. In column/StackCell flotation of three main mineral deposit ore composites, the rougher-scavenger-cleaner circuit Cu, Au and Ag flotation recoveries were 90.4~95.8% at a copper grade of 13.6-17.4%, 87.5-95.1% at a gold grade of 101-145.9 g/t, and 88.6-91.8% at a silver grade of 62.6-251.4 g/t, respectively. The benefits of Eriez Column/StackCell flotation technologies include high flotation selectivity and increased recovery due to unique hydrodynamic designs. Specifically, the StackCell design facilitates high turbulent kinetic energy dissipation rates to improve fine particle recovery and incorporates countercurrent wash water to significantly reduce hydraulic entrainment of the finest size gangue minerals to the froth product.

Feb 1, 2023

By Hooman Askari-Nasab, AHLAM MAREMI, EUGENE BEN-AWUAH

In oil sands mining, tailings are voluminous unwanted by-products generated from extracting the desired mineral from the mined ore. Dyke construction and backfilling activities require well-managed techniques to facilitate progressive reclamation at the earliest opportunity. This directly affects the sustainability and profitability of the mining operation. This research introduces a goal programming framework that simultaneously optimizes the (1) production schedule with limited duration stockpiling and directional mining; (2) dyke construction schedule; (3) size, shape, and location of tailings-cells; and (4) mining and processing production targets. The results show that in creating in-pit tailings-cells designs, decreasing the mining-cells volume and increasing the number of mining-cells improve the net present value of the operation due to increased operational flexibility. The model generated a uniform schedule for ore and practical tailings-cells designs for backfilling activities. Integrating tailingscells optimization into oil sands mine planning and waste management ensures the efficient use of in-pit mined-out areas required for sustainable operations.

Apr 14, 2021

By I. Iwasaki

Precious metals are commonly believed to be recovered along with sulfide minerals in flotation, but a few neutron activation analyses showed that the recoveries of gold and silver were unexpectedly low. Recoveries of platinum group metals remained unresolved due to interferences in the analyses. Electron micro-probe, scanning electron microscope and scanning auger microprobe analyses have identified nickel arsenide minerals in the ore and confirmed a close association of platinum group metals with the arsenide minerals as minute inclusions. These results indicated a need for re-evaluation of flotation procedures which have so far ignored special problems related to arsenide minerals. The electrochemical and flotation behaviors of nickel arsenide and their implications to the flotation recovery of arsenide minerals from copper-nickel bearing Duluth gabbro are presented.

Jan 1, 1985

By Juan J. Monsalve, AMAN SONI, Nino Ripepi, Richard Bishop

The design and strength of pillars are important parameters while implementing the room-and-pillar mining method in a limestone mine. The process becomes complex with the presence of the karst voids which are frequent phenomena in a carbonate rock formation. The karst system is a network of cavities that along with an omnipresent fracture network may lead to ground control issues in a limestone mine. The objective of this study is to provide a safe and reliable alternative design for a pillar in a case study mine for safe and efficient ore recovery. This research is a continuation of a previous study aimed at studying the effect of karst void on the strength of the same limestone pillar. It was assessed from the calculated pillar strength and the estimated redistributed stresses that the pillar is capable of countering more stress than is currently imparted on it. Numerical modeling studies combining in situ stress determination and excavation sequencing were used to estimate the existing stresses on the pillar. Different possibilities of modification to existing pillar design were simulated using Distinct-Element Modeling (DEM) to determine a better design. Discrete fracture networks (DFNs) were included to imitate the effect of the presence of discontinuities. An effort is also made to understand the variation of pillar strength with height for karst-affected pillars using two different constitutive models. This study serves as a preliminary investigation in terms of improving the future design of pillars and also while recovering old pillars prone to karst formation.

Jan 30, 2023