Search Documents

By Dirk van Zvl

The design of cover systems for reclamation schemes in tailings requires estimation or determination of tailings materials properties such as compressibility, shear strength and consolidation characteristics. It is very difficult and expensive to obtain truly undisturbed tailings samples for laboratory testing. In situ testing methods have been developed for economically obtaining large amounts of information. Two of these methods are described, the piezocone and the flat plate dilatometer. Both of these methods provide a rapid means of detailed material identification in a nearly continuous fashion for the entire depth investigated. The equipment is described and typical data from a uranium tailings impoundment is presented. The results are compared and the advantages and disadvantages of these methods are discussed.

Jan 1, 1984

By G. ALBORNOZ, S. Utili, A. AGOSTI, C. VALDERRAMA, R. PELL, N. Morales

The steepness of the slopes of an open pit mine has a substantial influence on the financial return of the mine. The paper proposes a novel design methodology where overall steeper pitwalls are employed without compromising the safety of the mine. In current design practice, pitwall profiles are often planar in cross-section within each rock layer; i.e., the profile inclination across each layer tends to be constant. Here instead, a new geotechnical software, OptimalSlope, is employed to determine optimal pitwall profiles of depth varying inclination. OptimalSlope seeks the solution of a mathematical optimization problem where the overall steepness of the pitwall, from crest to toe, is maximized for an assigned lithology, geotechnical properties, and factor of safety (FoS). Bench geometries (bench height, face inclination, minimum berm width) are imposed in the optimization as constraints which bind the maximum local inclination of the sought optimal profile together with any other constraints such as geological discontinuities that may influence slope failure. The obtained optimal profiles are always steeper than their planar counterparts (i.e., the planar profiles exhibiting the same FoS) up to 8° depending on rock type and severity of constraints on local inclinations. The design of a copper mine is first carried out employing planar pitwalls, secondly adopting the optimal pitwall profiles determined by OptimalSlope. The adoption of optimal slope profiles leads to a 34% higher net present value and reductions of carbon footprint and energy consumption of 0.17 Mt CO2 eq and 82.5 million MJ respectively due to a 15% reduction of rockwaste volume.

Feb 9, 2022

By James J. Olson

Most of the projects summarized in this paper are funded under the Bureau's Advancing Metal-Nonmetal Mining Technology program and are part of the in situ mining subprogram coordinated at the Twin Cities Mining Research Center. The borehole mining equipment development, are funded under the Bureau's Advancing Coal Mining Technology program, is essential to accelerated progress in the in situ mining subprogram, and some background information on this concept is included. The initial in situ research projects started in 1971-72 evaluated some of the critical blast design parameters for in situ copper leaching. The present program totals about $1 million per year and includes in-house research projects, cooperative (cost-sharing) projects with the mining industry, and research and development contracts. Two different extraction schemes are under investigation: inplace leaching and borehole (or slurry) mining. The principal commodity targets for the Bureau's improved in situ mining technologies include copper, uranium, coal, and potash. The principal purpose of this paper is to inform the mining industry of the in situ mining research recently completed or being conducted by the Bureau of Mines. In addition the Bureau encourages companies to comment on the program accomplishments as well as offer suggestions on top priority research needs for improving the in situ mining methods described in this paper.

Jan 1, 1977

By Z. Jin, D. DePaoli, P. Zhang

"Phosphorite, or phosphate rock, is the most significant secondary rare-earth resource. It contains high amounts of phosphate-bearing minerals along with low contents of rare earth elements (REEs). In Florida, about 19 Mt of phosphate rock are mined annually and most are used to manufacture fertilizers using a wet process, in which sulfuric acid reacts with phosphates to produce phosphoric acid and phosphogypsum. In the wet process, REEs are also leached out into solution and eventually get lost in the leaching residue and phosphate fertilizer. Recovering REEs from Florida phosphate rock in the wet process will be beneficial to broadening rare-earth availability, improving the quality of phosphoric acid product and protecting the environment.This study focuses on the influences of wet-process operating conditions on REE leaching efficiency. The results indicate that REE leaching efficiency increases with phosphoric acid addition in the initial pulp. At a temperature of 75 °C, a stoichiometric ratio of sulfuric acid (H2 SO4 ) to calcium oxide (CaO) of 1.05 and a weight ratio of liquid to solid of 3.5, REE leaching efficiency reached a relatively high value of 52.82 percent. The trends of REE leaching efficiency were similar to those for phosphoric acid (P2O5 ). Extensive tests on the leaching residue showed that during leaching, about 90 percent of the REEs were released from the phosphate rock but only 52.82 percent ended up in the leaching solution. This phenomenon can be attributed to two factors: (1) the effect of phosphate ions (PO4 3-) in the solution, which caused REE ions to form REE phosphates and be precipitated into the leaching residue, and (2) the influence of large amounts of anions such as sulfate (SO4 2-), dihydrogen phosphate (H2 PO4 -) and hydrogen phosphate (HPO4 2-) anions as well as the polar molecule H3 PO4 , which surrounded the REE cations and formed an ion atmosphere that prevented the PO4 3- from contacting and combining with REE cations. Interaction of these two opposite effects determined the REE distribution between leaching solution and residue."

Jan 1, 2017

By Yosry A. Attia

One of the most significant advances in Mineral Processing in recent years, is the development of the selective flocculation technology. The technology is primarily aimed at recovering the mineral values from ultrafine ore suspensions. This is achieved by selectively aggregating the mineral particles in question to such size as to enable their effective separation from the suspension. Selective flocculation utilizes the differences in the physical-chemical properties of the various mineral components in the mixed suspension. It is based on the preferential ad- sorption of an organic flocculant on the particular solids to be flocculated, leaving the remainder of the particles in suspension. In order to understand the mechanics of this process, selective flocculation may be divided into four major sub processes; these being: ore slurry dispersion, in which all the particles are stably and uniformly distributed in the suspension with the individual particles being essentially separate; flocculant selective adsorption and floc formation; floc conditioning, which aims at obtaining flocs with desire properties for their subsequent separation and with minimum entrapment of dispersed particles; and floc separation from the suspension. These sub processes will be reviewed later in this article.

Jan 1, 1982

By H. Lawrence

In 1977, the Bureau of Mines awarded a grant to the State of South Carolina to explore the possibility of using Landsat multispectral scanner (MSS) data as an aid in monitoring surface mining activities in selected counties of the State. Work had been done in Aiken County prior to the grant by Bureau of Mines and State personnel at the EROS Data Center using both the GE Image 100 and ESL IDIMS systems. The initial work on the 1-100 consisted of locating and measuring the areas of various kaolin mines. The results were excellent on location, identification, and accurate area measurements of several mines as compared with aerial photos of each mine. The effort also included locating and measuring the size of all mines (including sand and gravel) within two U.S. Geological Survey (USGS) 7 ½ min quadrangle maps. Line printer overlays using the IDIMS equipment and software resulted in the location of all known mines within an estimated error less than ±91.4m (5300 feet). Mine acreage was calculated by counting each symbol (which represented one pixel) and multiplying by 1.1 (the number of acres per pixel). Figure 1 shows a portion of one quadrangle overlay. Table I gives a comparison of acreage measured for sever- al mines from the 1-100 and IDIMS systems vs. aerial photo measurements.

Jan 1, 1979

By Jameel Menashi

Aqueous solutions of Na2Cr04 can be reduced with CO to produce hydrous Cr203 and NaHCO3/Na2CO3. CH3OH, HCOO and HCHO in the presence of CO2 also reduce Cr 6+ and yield similar products. It is shown that the rate of Cr6+ reduction can be represented by the expression -d[Cr6+]/dt=k[Cr6+)1/2[R] where [R] is the aqueous phase concentration of CH3OH, HCOO- or CO. With these three reductants, the activation energies for the reduction processes are comparable and are of the order of 100 kJ/mole. Rapid reduction rates are attained at temperatures in excess of 220°C and, with these three reductants, a green acid-insoluble readily filterable hydrous Cr203 is formed. With HCHO significant reduction of Cr6+ occurs at about 80-100°C and an acid-soluble violet modification of hydrous Cr2O3 is formed. The reduction process is reasonably selective: solutions of Na2CrO4 contaminated with Mo6+ and W6+ can be reduced to yield a Cr2O3 product with significantly reduced contaminant levels. These findings are utilized as a basis for a process for recovering chromium from secondary source materials.

Jan 1, 1984

By O. B. Bucklen

The Coal Research Bureau of the School of Mines at West Virginia University, using a modified design of a Russian flotation device, was able to obtain a clean coal product containing 7.64 percent ash with 94 percent yield and 97 percent coal recovery. This favorable performance was obtained with the semi-pilot scale flotation cell operating as a simulated three stage unit on slurry taken from the fine coal circuit of a coal preparation plant. This experimental device, consisting of a sheet metal cyclone-like unit mounted on a U-shaped uplift pipe, uses a combined flotation and cyclone action to beneficiate the minus 14 mesh partially cleaned feed product. In addition to providing comparable analytical results, the airlift-cyclone possesses other attractive features among them being a low capital expenditure, utilization of moderate plant floor space, efficient "operation on high density feed slurry, and absence of moving parts.

Jan 1, 1964

By A. K. Bhasin

The movement of solid particles in a liquid represents an area of interest in many fields of science and technology. Knowledge of the behavior and characteristics of solid-liquid suspensions is of great importance to many areas of mineral processing. In order to characterize a solid-liquid system, the following factors must usually be considered: a) density of the liquid b) rheological properties of the liquid c) density of the solid particle d) size and shape of the solid particle e) volume fraction of solid particles f) relative motion of solid particles and liquid phase Other variables such as the effect of the containing vessel walls, Brownian movement, inter-particle friction, fluid slip and electrostatic effects, are important in special circumstances. Thus it is evident that a complete theoretical treatment is not possible covering all situations. Studies of the kinematic behavior of solid particles in a liquid have been approached by two methods: 1) Assessing the movement of a single particle and extrapolating to a multi-particle system; 2) Modifying the continuum mechanics of single-phase liquids in such a way as to account for the presence of solid particles. The first approach in general utilizes the method of particle mechanics. Extension to a multi-particle system gives rise to very complicated mathematical computation. The creeping motion equations do, however, furnish a practical, useful basis for achieving a uniform treatment and a better understanding of the phenomena. This approach is useful in the study of sedimentation and hindered settling processes.

Jan 1, 1971

By B. R. Benner

Progressive improvements in crusher design, screening efficiency, and operating experience along with the downsizing of many taconite operations has resulted in the abilitv of some crushing plants to produce a substantially finer product. This finer product opens the possibility of replacing the rods in the rod mill with balls as is the current practice at Sydvaranger, Norway. If this replacement could be accomplished substantial savings associated with metal wear and the elimination of rod charging may be realized. The purpose of this study was to compare the performance of a mill charged with rods with the performance of the same mill charged with balls at the pilot scale. The first objective was to establish whether we could achieve the same throughput rate at the same mesh-of-grind in a mill in which the rod media has been replaced by balls. The second point was to determine whether the ball media would create a significant tramp oversize problem.

Jan 1, 1990

By R. E. Thill

An ultrasonic, pulse-immersion apparatus and method are described for determining the effects of moisture on the dynamic elastic properties of rock. The method provides an alternative approach for assessing the moisture sensitivity of rocks. Ultrasonic wave velocities are continuously monitored in immersed rock samples as a function of water absorption and time up to saturation. Moisture effects on compressional wave velocity vary as a function of the type of rock and the time and amount of water absorption. Regression analyses are used to curve-fit plots of the data and to derive empirical expressions for compressional wave velocity as a function of water content for different categories of rock. Results indicate that compressional wave velocity can be used to predict both the moisture content and its effect on strength and deformational properties of rock. These results have potential for detecting or monitoring bad roof conditions in situations where the mine rock exhibits strength degradation with moisture absorption.

Jan 1, 1986

By Rebecca Mae Summer

Large scale surface mining has a major impact on land use. Without reclamation, abandoned mining sites are usually less productive than before mining. With increasing and completetive land use demands in the United States, it becomes increasingly evident that multiple land use should be considered for all areas that will be mined, with special emphasis on coal, sand, gravel, and stone. The mining of these commodities affects the largest land areas and the latter two are commonly mined near population centers where high land-use pressures justify serious consideration of multiple use. Typically, sequential use will mean restoration of the mined land or at least transformation of the land into a useable state. Determination of land reclamation capability is a viable approach to planning reclamation of surface mined land. The natural resource base--geology, soil, and water--controls the type and intensity of land-use practices which can be sustained following mining. Evaluating physical limitations can eliminate consideration of uses which would severely impair the environment or which are impractical. This approach provides for an environmentally and economically sound land use at very little cost. In addition, it can save or make money for the mining company and landowner. Sand and gravel is an especially significant resource because it is mined throughout the entire country and commonly extracted near cities. Increasing urban growth and industrial activity require increased supplies of sand and gravel. This translates into expanded surface mining and an increase of disrupted land. Oftentimes this land is within an urban area and has potential for real estate or water-based activities. Therefore, if reclamation is planned and carried out concurrently with mining, it is definitely feasible and

Jan 1, 1977

By Huiqin Yao, Dongmei Liu

The study investigated the potential use of low activity circulating fluidized bed combustion (CFBC) ash and phosphate tailings for the production of a filling material based on the cement. The phosphate tailings were used as aggregate and consolidated by cement and CFBC ash. The results showed that the bleeding rate and fluidity of all mixtures decreased with the increasing the amount of CFBC ash. The fluidity of filling slurry is highly related to the experimental factors such as the content of sulfur solid ash, B/A ratio, and mass concentration. The replacement of CFBC ash ranging from 20 to 40% led to a significant decrease in setting time and an obvious increase in compressive strength, but the above effect was obviously weakened when reducing the mass concentration and B/A ratio. The hydrated calcium silicate gel and ettringite generated from the hydration of cement and CFBC ash were the main sources of strength for the filling materials. When the recommended proportion was 1/6 binder/phosphorus tailings ratio, 76% solid content, and 40% CFBC ash replacement, the filling material still met demands on working and mechanical properties; at the same time, the utilization of CFBC ash and phosphorus tailings was maximized.

Oct 11, 2021

By I. Mazalov, G. Ospanova

Introduction Today, uranium is of great interest because of its application to nuclear power and nuclear weapons. Kazakhstan has been an important source of uranium for more than fifty years. All uranium products are exported. Results In Kazakhstan uranium exploration started in 1948 and developed in several parts of the country thru mining of hard rock deposits. There are known around 50 uranium deposits in six provinces: Shu-Sarysuyskaya (57%), North Kazakhstan (18%), Syrdaryinskaya (15%), Ilyiskaya (7%), Caspian (2%), Balkhash (1%). In the Northern Kazakhstan province, KazSabton took over Tselinny Mining & Chemical Co in 1999. In this province the stockwork is of Paleozoic and Paleozoic folded complexes origin. In the Balkash province some mining of volcanogenic deposits occurred during the Soviet era. This province’s stockwork is of Endogenous origin.In the Ili province uraniumis mainly found in uranium-coal deposits formed by oxidation of the lignite beds roofs. In the Caspian province the Prikaspisky Combine operated since the 1960s a major mining and processing complex on the Mangyshalk Peninsula. This led to the founding of Aktau. It was privatised as Kaskor in 1992 and operations ceased in 1994. The uranium occurrence is associated with the phosphorous from fossil fish bone detritus conglomeration. In the Chu-Sarysu province, which has more than half the country's known resources, both Stepnoye and Tsentralnoye have been operating since 1978 and 1982 respectively. Uranium mineralization occurred in the regional stratum oxidation zones. In the Syrdarya province slightly to the west of the province’s center the No.6 Mining group has been operating since 1985. Uranium mineralization occurred in the regional stratum oxidation zones.

Jan 1, 2007

By JIACHENG XIE, Juanli Li, Wenyong Du, Tao Cui, Mengyao Dong, Pengfei Huo

The operation of intelligent coal mining in complex geological environment is still unable to realize automation. In order to realize the autonomous cutting of fully mechanized mining equipment and improve coal production, a mining and transportation equipment dynamic advancement path planning method based on spatial kinematics coordinate deduction prediction and real-time correction prediction of coal-rock state identification of equipment cutting current index are proposed. Firstly, the spatial motion law of the mining and transportation equipment is analyzed, and the mathematical model of the spatial motion of the mining and transportation equipment is established. The relationship between the adjustment of the shearer rocker arm and the pose change of the scraper conveyor is determined, and the coordinate deduction model of the spatial advancement position of the equipment is determined, which provides a theoretical basis for the advancement path planning of the mining and transportation equipment. Then, on the basis of the mathematical model construction, combined with real geological data and equipment information, the three-dimensional dynamic planning of the advancement path of the mining and transportation equipment is carried out from the two dimensions of the horizontal advancement direction and the shearer walking direction. At the same time, the relationship between the cutting current index of shearer and the state recognition of coal-rock mass is analyzed, and the coal-rock mass state identification of cutting current and the adjustment of rocker arm model is constructed, and the real-time dynamic correction of three-dimensional path is carried out, so that the planned path can better adapt to the sudden change of real geological environment. Then, using the unity3d virtual reality technology, a simulation system for the horizontal advancement path planning of the virtual mining and transportation equipment is constructed, which simulates the real advancement operation process of the mining and transportation equipment and conducts advancement training. Finally, the dynamic advancement scheme update prediction based on the existing actual cutting but ahead of the actual cutting is realized in the virtual scene, and the optimal scheme is transmitted into the existing prediction cutting system to guide the actual physical equipment mining. The path planning method can control the coordinate position error of the advancing cutting path within 15 mm, which provides ideas for the research on the advancing path planning of fully mechanized equipment.

Nov 22, 2022

By CHENCHEN SUN, GUOPING LUO, GUOCHENG ZHANG

Preparation of briquettes by adding CaF2 reagent into the Australian iron ore powder. The structure and morphology of iron ore briquettes during various reduction stages (i.e., Fe2O3→Fe3O4, Fe3O4→FeO, and FeO→Fe) were observed via an ore microscope and scanning electron microscopy. The results showed that CaF2 reacted with SiO2 to form CaO and SiF4 gas during the roasting process. The reduction swelling index decreased from 12.36 to 8.83% when the CaF2 content in the briquettes increased due to CaF2-mediated refinement of the hematite grains during the first stage of the reduction process. Lattice distortion resulting from the presence of Ca2+ in the FeO lattice during the second stage of the reduction process, coupled with an increase in the porosity of the iron ore briquettes and the formation of a low-melting-point slag phase, promoted the anisotropic growth of FeO lamellar crystals, which resulted in an increase in the reduction swelling index from 4.27 to 7.36%. During the third stage of the reduction process, the growth of iron whiskers was promoted by wüstite (FeO) lattice distortion caused by a solid solution of Ca2+ in the FeO lattice; the reduction swelling index increased from 15.61 to 24.72%, resulting in the catastrophic swelling of the iron ore briquettes.

May 27, 2021

By A. L. Mular

A great deal of effort is being expended by mineral processing engineers to acquire a basic knowledge of modelling and optimization techniques. Stimuli such as immediate process improvement, expanded process understanding, optimal flowsheet design and re-design, and the development of new and better control systems are goals which excite the imagination in terms of increased profits. To reach these goals, process models and efficient optimization strategies, regardless of their purpose, assume an important role. Consequently, few of us can argue that such efforts are of no value. The purpose of this paper is to review empirical modelling methods and optimization strategies which appear to be of value to mineral engineers.

Jan 1, 1972

By D. F. Lillie

The milling plant of Bicroft Uranium Mines Limited has been in operation for a period of 2 years. During this time many changes, both physical and chemical, have been made in an effort to improve plant efficiency. Investigational work has been facilitated greatly by the fact that the Bicroft mill consists to a large extent of two parallel circuits; however, the number of inter-related variables is great, and it is difficult to measure, let alone control, all of them simultaneously. The Bicroft mill staff feel that much progress has been made, but there is much yet to be done and many questions still to be answered. The property of Bicroft Uranium Mines is located in Cardiff Township in the Highlands of Haliburton County, southeastern Ontario, some 140 miles northeast of the city of Toronto and 70 miles due north of Lake Ontario. The ore-bearing dikes are classed as mafic, non-segregated, syenite and granite pegmatites. Microline, microline perthite, quartz, uraninite, uranotharite, fluorite, titanite, cyrolite, calcite, pyrite, pyrrhotite and molybdenite as important accessories. The mill was designed for a nominal capacity of 1,000 tpd with all sections except grinding, leaching and clarification capable of 1,500 tons. Feed was entered to one mill unit on October 29, 1956 and to the second parallel line on November 13. The total feed rate was at 1,000 tpd on November 15. The first precipitate was produced on November 12. By August 1958 the average entry had been increased to 1,410 tpd without the installation of any additional major equipment. The overall recovery has been greater than 93,0 pet do several months, but a recovery of 92.5 pct appears to be most economical. Operating time for 8 months in 1958 has been 97.1 pet although all grinding mills were relined during this period.

Jan 1, 1959

By Robin Burgess-Limerick

The introduction of automation to mining has great potential to reduce safety and health risks by removing people from hazardous situations. However, automation changes the tasks performed by people and may introduce new tasks. For the system to function optimally, these tasks must be designed taking human abilities and limitations into account. Humansystems integration refers to systems engineering processes that ensure that human-related issues are adequately considered during system planning, design, development, and evaluation. During procurement of automated systems, a human-systems integration program plan should be prepared that describes the human-systems integration activities that will be performed to address each of the six core domains of human-systems integration: staffing, personnel, training, human factors engineering, safety, and health.

Jun 16, 2020

By M. Sadegh Safarzadeh, Erich U. Petersen, Jan D. Miller

"An acid bake-leach process has been identified and applied to an enargite concentrate containing ~67% enargite, ~27% pyrite (FeS2), ~3% chalcopyrite (CuFeS2), ~6% sphalerite (ZnS) and <1% galena (PbS). Sulfuric acid baking of this concentrate resulted in the transformation of the concentrate to S8, As2O3, HFe(SO4)2•4H2O, PbSO4 and Cu0.47Fe0.53SO4•H2O, all of which (except elemental sulfur and PbSO4) dissolved during the water leaching step. More than 87% Cu and 64% As were leached when the concentrate was baked at 200°C over 7 hours with a sulfuric acid-toconcentrate weight ratio of 1.6. Less than 1% As was lost to the gas phase. Upon water leaching, copper and arsenic were released to the solution at a concentration ratio of about 3:1. While enargite is very reactive during the sulfuric acid baking reaction, other minerals present in the concentrate such as pyrite, galena and sphalerite may compete to consume sulfuric acid and be converted into their corresponding sulfates at different concentrations. The purpose of this paper is to present our examination of the effects of sulfuric acid dosage on the extractions of Cu, Fe, and As from an enargite concentrate. In this regard, the concentrate, baked concentrate, and the leach residues are characterized and a conceptual process flowsheet is described for the acid bake-leach process for the treatment of enargite concentrates.IntroductionThe occurrence of enargite (Cu3AsS4) in copper ores and concentrates and the associated high arsenic values in such resources have resulted in a considerable decrease in the demand for such concentrates because they cannot be economically processed using conventional technologies such as smelting and atmospheric leaching (Mihajlovic et al., 2011). The exploitation of such problematic deposits through competitive treatment strategies will be required in the near future in order to satisfy increasing pressure from the copper market. It is expected that the average arsenic grade of copper concentrates will increase from 0.17% in 2008 to 0.22% by 2020 (Mayhew et al., 2011).The acid bake-leach process was identified and selected for further investigation at the University of Utah as a possible process alternative for the treatment of enargite concentrates. In this case, adequate amounts of concentrated sulfuric acid are mixed with the concentrate and heated to the temperature range 150-300°C. Subsequently, the baked material is leached with water/weak acid and the acid bake-leach process has some advantages over conventional sulfuric acid leaching (Prater et al., 1970). During water leaching, metal sulfates are released in solution, after which they can be extracted through well-known hydrometallurgical techniques. While the majority of the work has been done on oxide minerals, there is a limited record of sulfuric acid baking of sulfides."

Jan 1, 2015