Search Documents

By H. E. Bartlett

Previously, the grade of ore at the shaft head was taken to be equivalent to the grade measured in the faces by means of chip sampling. The tonnage mined from the stopes is determined from survey volumetric measurements. Estimates of shaft head grade and tons include the grades and tons of waste, development ore, sweepings from old areas, and other sources, not all of which are sampled. The tonnage of ore delivered at the shaft is often estimated using skip factors. These factors are subject to manipulation and not all the skips are filled to the same level. Consequently, both the grade and tonnage of ore delivered at shaft head are subject to a measure of uncertainty. For many years, these uncertainties have led to disputes between shaft managers and metallurgists over the reconciliation between shaft tons and grade and plant tons and grade. These problems are compounded when several shafts feed a central processing plant. Shaft bonuses and a shaft?s profitability are affected by poor gold allocation methods. Without measurement of the grade and tonnage from all shafts, a poorly performing shaft could benefit at the expense of the other shafts. In order to improve the measurement of grades and tonnage at the shaft head, which is the custody transfer point between the mine and surface operations, South African mining companies have developed a methodology to measure the mass of ore from each shaft using rail weighing equipment, and the run-of-mine grades delivered from each shaft using cross-stream (go-belt) sampling. Harmony Gold Mining Company has implemented the rail weighing and go-belt sampling methods for their shafts. This paper deals with the statistical tests on the procedures and control measures that are in place to establish confidence in the gold allocations. The metal accounting system for examining the allocations follows the first principle of the AMIRA P754 Metal Accounting Code of Practice namely ?The metal accounting system must be based on accurate measurements of mass and metal content. It must be based on a full check-in check-out system?. The check-in is mass and grade of run-of-mine ore and the check-outs are the plant input grades and the recovery and residue from the plant. The balances between check-in and check-out are the subject of the statistical analyses, which have been conducted using the classical statistical tests and procedures that are generally used in all fields of endeavour. It is concluded that the gold allocation procedures that rely on go-belt sampling and rail weighing of ore from shafts has been successfully implemented, and that the system, which has been in operation at Harmony since 1993, has won general acceptance from stakeholders, with the gold allocations being perceived as being fair to all. Apart from the on-mine issues of bonuses and fair allocations, accurate metal accounting assists in the broader issues of generating accurate production figures for management. An added benefit of weighing and sampling ore at the shaft head has been that shafts now have daily moving average grades, which are used for grade control. The go-belt sample at the shaft head is the first accurate sample of production in the value chain from face sampling to gold bullion. Keywords metal accounting, go-belt sampling, run-of-mine sampling, codes of practice, AMIRA P754, train weighing, statistical analysis, gold split, allocation of gold, metal balance, grade control.

Jan 1, 2014

By F. Samimi Namin

One of the main tasks in exploitation of mines is to select a method suitable for the deposits, specific features including geometric, geo-mechanical and geological features. The purpose of selecting a mining method at this stage is to choose one or more method(s) having the most coordination with the deposit?s conditions and external factors, including the allocated budget and local technology for detailed feasibility studies. Several methods have been developed in the past to evaluate suitable mining methods for an ore deposit, based on its physical characteristics. These approaches can be classified into three groups: (1) profile and checklist methods, (2) numerical ranking (scoring) methods, and (3) decision-making models. Most of these methods have shortcomings. Considering the fact that most of the specifications of mineral deposits, such as dip and depth, are linguistic variables, absoluteness of the explaining parameters by previous methods can be mentioned as the most important disadvantage of these methods. This paper discusses the Fuzzy technique for order performance by similarity to ideal solution (Fuzzy TOPSIS) to determine the mining method. The fuzzy decision making (FDM) software tool is employed to develop a Fuzzy TOPSIS based model. Application of this model with various values (crisp, linguistic and fuzzy) of the deposit eliminated the existing disadvantages of other methods. Two empirical illustrations demonstrate the effectiveness and feasibility of the evaluation procedure. These show that the proposed model performs better than its alternatives. Keywords: mining method selection, fuzzy TOPSIS, decision making, mining engineering, linguistic variables.

Jan 1, 2008

By D. R. Tesarik, F. M. Jones, J. B. Seymour

As part of safety and stability studies at three underground mines in the United States, researchers installed earth pressure cells and embedment strain gauges in cemented rockfill to measure stress and strain changes as mining progressed and the rockfill was loaded. Data from these instruments were used to calculate the in situ modulus of the rockfill for two of the mines. A three-dimensional numerical model of a cemented rockfill cap was validated with data from extensometers anchored in the mine roof and sill; this model was then used to estimate deformation modulus at the third mine because the earth pressure cells and embedment strain gauges recorded negligible changes. Rockfill binder used at these mines ranged from 4 to 8 per cent of the dry components by weight, the water-to-cement ratio was from 0.42 to1.0, and the largest aggregate size in the three mixes ranged from 5 to12 cm (2 to 4.7 in). The range of the calculated in situ deformation modulus values was large, but as expected, it was bracketed by modulus values for cemented tailings and roller-compacted concrete with similar cement contents and water-to-cement ratios. Dans le cadre d’études sur la sécurité et la stabilité de trois mines souterraines situées aux États-Unis, les chercheurs ont installé des palpeurs de pression des terres et des extensomètres d’encastrement dans les remblais cimentés afin de mesurer les variations relatives à l’effort et à la déformation des terrains durant l’exploitation minière et le chargement du remblai. Les données recueillies à l’aide de ces instruments ont servi au calcul du module in situ du remblai dans deux de ces mines. Le modèle numérique tridimensionnel de la semelle d’un remblai cimenté a été validé à partir des données recueillies par les extensomètres ancrés dans la voûte et dans la semelle de ces mines; ce modèle a ensuite été utilisé pour estimer le module de déformation à la troisième mine, étant donné que les palpeurs de pression des terres et les tensiomètres enfouis avaient relevés des variations négligeables. La matière d’agrégation de l’enrochement utilisée dans ces mines comportait entre 4 % et 8 % des composantes sèches par poids; le rapport eau-ciment se situait entre 0,42 et 1,0; et la taille des agrégats les plus gros dans ces trois mélanges était de 5 cm à 12 cm (2 po à 4,7 po). L’écart entre les valeurs calculées des modules de déformation in situ était grand, mais comme on s’y attendait, cet écart a été compensé par les valeurs modulaires des résidus cimentés et du béton tassé au rouleau avec des teneurs en ciment et des rapports eau-ciment semblables. Als Teil der Sicherheits- und Stabilitätsstudien an drei Bergwerken in den Vereinigten Staaten von Amerika installierten Forscher Erddruckgeber und Einbindungsdehnungsmesser in zementierter Steinschüttung, um Spannungs- und Dehnungsveränderungen während der fortlaufenden Bergarbeiten und der Belastung der Steinschüttung zu messen. Daten von diesen Instrumenten wurden dazu verwendet, das In-Situ-Modul der Steinschüt-ung für zwei Gruben zu berechnen. Ein dreidimensionales numerisches Modell einer zementierten Steinschüttungsschwelle wurde mit den Daten von den im Grubendach und in der Schwelle verankerten Extensometern validiert; dieses Modell wurde dann dazu eingesetzt, um das Deformationsmodul in der dritten Grube zu schätzen, da die Erddruckgeber und Einbindungsdehnungsmesser nur geringfügige Messabweichungen feststellten. Das in diesen Gruben verwendete Steinschüttungsbindemittel variierte zwischen vier und acht Prozent an Trockenkomponenten nach Gewicht, der Wasser-Zementfaktor betrug zwischen 0,42 und 1,0 und die größte Zuschlagstoff-größe in den drei Mischungen schwankte zwischen fünf und zwölf Zentimetern. Die Reichweite der berechneten Werte des In-Situ-Deformationsmoduls fiel etwas breit aus, aber es fand erwartungsgemäß eine Klammerung der Modulwerte zwischen den Zemen-trückständen und dem durch Walzen verdichteten Beton mit ähnlichem Zementanteil und Wasser-Zementfaktor statt.

Jan 1, 2003

This paper describes experimental investigations into the reductive decomposition of arsenopyrite/pyrite (FeAsS/FeS2), a gold and silver bearing iron/arsenic sulphide using metallic iron powder. The main objective was to establish and experimentally confirm the thermodynamic and kinetic feasibility of reductively decomposing the sulphide matrix for precious metals recovery. In this context, cyanidation leach tests were conducted on the reductive leach residues. The arsenopyrite/pyrite flotation concentrate, mainly studied in the hydrochloric acid medium, decomposed through the non?oxidative chemical dissolution reaction and the reductive decomposition reaction for the arsenopyrite and pyrite components, respectively. Desulphurization levels below 65% were achieved at pH values below 0.15 and iron to concentrate ratios above 1, and the system was characterized by overall very slow kinetics. The reaction system had a direct linear relationship with iron to concentrate ratio and an inverse relationship with pH. An analysis of the pyrite/iron galvanic system showed that pyrite forms a partially inert cathodic surface on which the anodic dissolution of iron occurs, supported by the hydrogen evolution reaction. This phenomenon explained the low desulphurization levels and the mineral decomposition seemed to be restricted to the non?oxidative chemical dissolution reaction for the arsenopyrite component. The cyanide leach of the reductive leach residues showed very little improvement in gold recovery. The reductive leach process for arsenopyrite/pyrite has considerable limitations in terms of both desulphurization and precious metals liberation. Keywords: Pyrite, arsenopyrite reductive leaching, hydrogen sulphide, invisible gold

Jan 1, 2009

The Skorpion process comprises three processing steps-atmospheric leaching in sulfuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the root causes of the crud formation in the solvent extraction circuit and optimization strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica.

Jan 1, 2007

By H. J. Le Roux, W. B. Drummond

1. INTRODUCTION We have a moral responsibility towards the world to reduce the harmful deposits we emit into the environment arising from beneficiation technologies. Industry has not willingly spent money to limit these emissions because it affected their profit margin with the end result of emitting harmful elements into the environment. Governments have thus rightly stepped in and enforced systematic reduction of these emissions through legislation. In the past beneficiation of sulphur bearing ores was typically done through hydro-metallurgical concentration, smelting, followed by Sulphur removal by converting processes like the Pierce Smith converter. The latter two processes emitted substantial quantities of Sulphur into the atmosphere. Spiralling costs and legislation have resulted in the quest to develop more efficient and environmentally friendly processes to achieve the same end results. New hydro-metallurgical processes like the ActiVox process has completely eliminated the pyro-metallurgical processes. Kansanshi are also operating a similar process. It however elicits other ground water and spillage pollution hazards and problems of it?s own. Various improvements has also been made to the pyro-metallurgical stages, examples being combined smelting and converting with the Noranda reactor, the Codelco CMT furnace, one step flash smelting/converting or the Mitsubishi continuous smelting, converting and slag cleaning process. The new converting processes are also normally enhanced using oxygen leading to higher SO2 gas strength with only a marginal increase in off-gas volume. These processes have led to better efficiencies and a more controlled environment that reduces pollution, but does not eliminate it completely. The fact that there are still more than 70 existing Pierce Smith converter plants throughout the world that needs to be replaced or upgraded at tremendous capital cost, means that we will have the environmental problems for some time to come. The need thus exists to cost effectively get these existing plants into a state where they meet the new environmental regulations, community and safety requirements. This paper will concentrate on just one aspect of this quest, i.e. reduction/removal of off-gasses emanating from the converting of non ferrous sulphur mattes to achieve higher or specialised grades of refined metals.

Jan 1, 2005

By K. Basaure, S. Palma, R. L. Castro

"Mud rushes are sudden inflows of fine wet ore within underground mines; they can harm people and equipment as well as cause production delays. Block and panel caving mines are prone to mud rushes in their production levels, with mud flowing from the drawpoints. Different mines have developed methods to control drawpoint conditions and thus perform safe ore extraction. The aim of this study is to develop a decision matrix and apply it to samples from drawpoints for the Diablo Regimiento mine, Codelco, El Teniente Division (Chile). The Abrams’s Cone was used to perform slump tests on mud samples and characterize their consistency by setting the saturation degree and packing. The unconfined strength for different saturation degrees and packing was then evaluated. The results show that conditions for fluid response in slump tests correspond to conditions for low strength in unconfined compression tests. We also found the water content value at which the flowing consistency changes from plastic to soft behaviour according to the slump test classification for each sample. This value varied between 12.2% and 16.9%, depending on the sample tested. Finally, a fluid security factor was defined in order to design an extraction pattern for the samples tested, based on the water content. We conclude that a very densely packed ore is not prone to flowing. The flow properties depend strongly on the specific properties of the ore tested, and consequently a specific criterion should be developed for different types of ore at a particular mine. The criterion developed for Diablo Regimiento ore provides critical water content values from 11% to 15%, depending on the ore type. IntroductionBlock/panel caving has the lowest cost and the highest production rates of all underground methods (Heslop, 2000; Hubert et al., 2000). Good management of the risks is important to ensure the security of personnel and infrastructure. Operational risks for the method include rockbursts, air blasts, and mud rushes (Hubert et al. 2000). A mud rush is defined as a sudden inflow of mud from a drawpoint or other underground opening into the mine (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005). Mud rushes can cause dilution, production delays, and damage to equipment as well as injuries and fatalities. The elements necessary for mud rushes are mud-forming material, disturbances, a discharge point, and water (Butcher, Joughin, and Stacey, 2000). All these elements are present in block/panel caving mines. Mud-forming material comes from ore milled by the caving process; water comes from underground and surface sources. Drawpoints in the production level are discharge points for the mud. Finally, several types of disturbance could trigger the mud rush phenomena: blasting, earthquakes, operation of equipment (Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012), arch collapse above drawbells (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Jakubec, Clayton, and Guest, 2012) and ore drawing (Butcher, Joughin, and Stacey, 2000; Butcher, Stacey, and Joughin, 2005; Call & Nicholas, Freeport McMoRan, and Hydrologic Consultants, 1998; Jakubec, Clayton, and Guest, 2012)."

Jan 1, 2017

The utilization of computer assisted tomography (CT or CAT-scan)as general non-destructive examination (NDE) technique and as research tool for scientists in South Africa, is limited due to the relative unavailability or nonexistence of such specialized analytical equipment. Many medical hospitals are equipped with X-ray CT scanners for the diagnostic examination of patients but do not easily allow paleontologist or other scientist to utilize their very expensive equipment. As from 2003, Necsa hosts the South African Neutron Radiography (SANRAD) and tomography facility where neutrons from the SAFARI-1 nuclear research reactor and their penetrating power as well as X-rays as a complementing tool, are utilized in many R&D applications. This facility is being made available to HEI and specifically utilized by postgraduate students as part of their studies and/or by industry on an ad hoc commercial basis. The capability of these radiation imaging facilities at Necsa will be demonstrated in areas such as paleontology, geosciences and specifically the physical properties of rock and the distribution of minerals in borehole cores, petrophysics to predict the percentage tar/oil/water content within sandstone samples and others. The penetration capability of neutrons through specimens with a matrix of high atomic number (dense materials) and their ability to be attenuated by low atomic number material (light density) makes neutron imaging complementary to X-ray imaging. The capability of X-ray and gamma radiation for relatively easy penetration through specimens of low atomic number allows for viewing of imbedded high atomic number materials and density variation. X-ray micro focus radiography is capable of resolving objects of micro scale size that are micro distances apart whereas X-ray phase contrast radiography utilizes the wave properties of the electromagnetic spectrum of X-rays to clearly define edges of the specimen under investigation. Many applications with neutrons as imaging probe are successfully applied at several facilities across the globe such as at NIST in USA, Neutra at PSI in Switzerland, and ANTARES at FRM2 in Germany, etc, are documented 4?9, through world conferences on neutron radiography, for example. This is achieved through very well thought through and implemented instrumentation from the production of neutrons to their detection and interpretation of the images. The need arose at Necsa to upgrade the current facility from 42-year-old technology, which was successfully applied in neutron imaging over the past 10 years, to state-of-the-art technology found at European facilities. This initiative started under the auspices of an IAEA-TC programme for the period 2007?2010.

Jan 1, 2008

SABS quality mark for explosives* AECI Explosives and Chemicals Limited has been awarded the SABS permit to apply the SABS standardization mark to al its permitted NO explosives manufactured at Modderfontein.

Jan 1, 1989

By A. F. Spinks, S. P. Nicholls

"The Lower Orebody at Chingola Division of Nchanga Consolidated Copper Mines, Limited, is a stratified orebody that is mined by a continuous caving system. The accurate determination of the developed and semi-developed ore reserves has always been difficult. The new system proposed in 1971 is designed to update and, as new informa¬tion becomes available, to account for the depletion of, the reserves.There are three main inputs to the system. These are borehole data, survey data and extractions data. The borehole data are input to a geological borehole master file system, which holds every recorded detail of a borehole in an easily extractable form. These data can be extracted for ore reserve calculations or for contour mapping of orebodies and rock types. The grades for use in the ore reserve calculations are extracted from the relevant boreholes.The survey data are information on the position of the blocks and drifts, taken from plans, and information on the scraper drift and trough drive positions taken from sections. The information is extracted from the plans and sections using a D Mac pencil follower. The ore reserve is calculated from the survey data and the borehole data.Data on extractions are taken from scraper operators' logs, tramming records, skips hoisted records and accepted mill tonnages and grades. Using these data, the mill tonnages are reconciled back to the drifts, to deplete the current ore reserves.As new workings are brought into operation and further evaluation holes are drilled, the relevant data are input and the new developed ore reserve is calculated."

Jan 1, 2014

By K. Hodgson, Cook. N. G. W.

Most structures are designed so that the possibility of failure is eliminated. However, some degree of failure in the rock around deep mine excavations is inevitable if mining operations are continued. The presence of failed rock constitutes a hazard the magnitude of which can be predicted by computer models from calculations of the energy change per unit area mined in stopes, or the field stress around service excavations. Empirical relationships between these calculable quantities and the incidence of rock failures and delays associated with them have been established. Experiments on the computer using different layouts enable the mining engineer to select the least hazardous of otherwise acceptable alternatives, and to predict the incidence of damage ahead of actual mining, so that appropriate measures to maintain an adequate degree of safety and productivity can be planned in advance.

Jan 1, 2014

By R. B. MacGillivray

The No. 2 Seam at Van Dyks Drift Colliery was found to be made up of six easily recognizable bands or plies of differing qualities. Not only did the plies differ from one another in quality, but their thickness and quality varied laterally across the mine. The economic production of a Iow-ash blendcoking coal for supply to the Japanese Steel Mills called for the mining of different portions of the seam. The portions that could be extracted economically varied in thickness and position within the No. 2 Seam across the mine. A unique system of selective mining had to be developed involving the dispatch of two separate streams of coal out of the mine. Conventional American mechanized pillarand-stall mining was used, and the productivity was improved by the installation of twin conveyor belts into a double-header section. The method of grade control that was instituted to ensure efficient extraction of the available coal reserves is described.

Jan 1, 1985

By A. J. S. Benade, N. B. Strydom, W. H. Van Der Walt

The influence of two weeks of microclimate cooling on the state of heat acclimatization by N. B. STRYDOM, M.Sc., Ph.D. (Illinois) (Fellow), A. J. S. BENADE, M.Sc. (Potch.) (Visitor), and W. H. VAN DER WALT, B.Sc. (Potch.) (Visitor) Five volunteer Black subjects were acclimatized according to the climatic-room acclimatization procedure, and their states of heat acclimatization were determined by the usual heat-stress test. The subjects thereafter wore pre-frozen jackets in a somewhat higher environmental temperature (33,9/35,6 °C). stepping at the same rate as before for four hours a day for fourteen days. The heat-stress test was repeated and followed by a similar test at the higher environmental temperature. It was found that fourteen days of microclimate cooling in a very hot environment had no adverse effect on the degree of heat acclimatization. The sweat rates during microclimate cooling remained high, even though no sweating is possible beneath the pre-frozen ice-jacket. which indicates that there is an increase in sweat rate from the areas of exposed skin.

Jan 7, 1975

Messrs B. R. Braekman and D. W. Penman have notified some errors in the Addendum that was attached to their paper, 'The Prieska experience: Flotation developments in copper-zinc separation', which was published in the August issue of this Journal (vol. 91, no. 8, pp. 264-265).

Jan 1, 1991

By G. M. Wright

We are only as good as we are perceived to be by others and, whilst there is every opportunity to revise and polish our written works, there are no second chances with a spoken presentation. At every level, conferences and seminars have been metaphorical graveyards for many an academic reputation.

Jan 1, 1990

The following corrections should be made to pages 346 and 347 of the December 1981 issue (vol. 81, no. 12) in the paper by O. L. Papendorf entitled 'A note on rapid determinations of present values in the presence of growth and inflation'. (1) Equation (2) on page 346 should read as follows:

Jan 1, 1982

By R. Morris, W. D. Clough

SYNOPSIS The design of an opencast coal mine over areas previously mined by underground mining methods presents several potential methods of mining the coal. The paper describes some basic methods of mining for the No. 2 seam of the Witbank Coalfield, which had previously been mined by the bord-and-pillar method.

Jan 1, 1985

NIM reports Report No. 1615 Fluorspar pellets. A survey of the world market and an assessment of future South African production. Report No. 1621 Correction for matrix effects in the analysis of solutions by X-ray-fiuorescence spectrometry. Notices Questionnaire on Technicians The Department of National Education's committee of enquiry into the education, training, utilization, and status of engineering technicians in the Republic of South Africa was established as a result of Resolution 6.3 taken at the Sixth Conference on Engineering Education: The Education and Training of Engineering Technicians. Vraelys oor Tegnici Die Departement van Nasionale Opvoeding se komitee wat ondersoek instel na die opleiding, gebruik en status van ingenieurstegnici in die Republiek van Suid-Afrika is gestig as gevolg van Besluit 6.3 wat geneem is tydens die Sesde Konferensie oor Ingenieursopleiding: Die Opleiding van Ingenieurstegnici. Competition for Student Members of the South African Institute of Mining and Metallurgy Each year the Institute offers a prize (or prizes should the entries warrant it) of up to R100 for the best paper or dissertation on a topic appropriate to the interests of the Institute. The competition is open to all Student Members of the Institute.

Jan 8, 1974

By J. G. Ferguson, R. E. Burnton

The nature of the coal and of the roof in No. 3 seam at Coal brook Collieries is such as to preclude the use, during bord and pillar mining, of conventional mining equipment that employs cutting and blasting in its production cycle. Continuous mining machines of the borer type, operating within a mining height range of 1,9-2,3 m, have been successfully employed in No. 3 seam since 1957.The experience gained with this type of equipment, the operational methods adopted, and the results achieved are described. The ventilation method used to eliminate the dust and methane hazards created by this type of equipment is stressed. The limitation on the minimum mining height that can be obtained with the borers in use has lead to the recent introduction of a Rotary Drum type of continuous mining machine. This equipment is capable of operating in areas where the seam width decreases to 1,5m. The production potential of the machine has been proved. The roof conditions created by the cutting action of the Rotary Drum type of miner are not considered satisfactory and a modified drum head profile is to be tried.

By R. R. Maclachlan

The Estimation of Fragmentation in Blast Muckpiles by Means of Standard Photographs, by H. van Aswegen and C.V.B. Cunningham. Journal of the South African Institute of Mining and Metallurgy, vol.86,no. 12. pp. 469-474. Dec.1986.We have recently read the above paper and wish to make a number of observations.

Jan 1, 1988