Search Documents

The re-use of waste water from coal preparation plant tailings is always desirable, but is generally problematic in terms of solid-liquid separation. Dewatering and disposal of coal slurry at a high percentage of moisture poses a major technological and environmental challenge to mining and mineral processing industries world-wide. Characterization and flocculation of these coal tailings reveals that the separation of fine coal tailings depends on factors such as size distribution, slurry viscosity, zeta potential, pulp density, circuit design, plant operating parameters, and the behaviour of solid particles in an aqueous medium. The present study was carried out on -600 mm coal tailings collected from a coking coal preparation plant of Jharia Coalfield, India, using anionic flocculent. Characterization studies revealed that the zeta potential was highest (-44 mV) at a pH of 9.0, the size range of the particles was 1.1?700 m, and the average ash content was 62.57%. Flocculation studies were performed at different solid concentrations, pH values, and polymer dosages. The results indicated an efficient settling rate of 178.15 mm/min at 8% solid (w/w) at a flocculent dosage of 32.50 g/t solid. The turbidity of the clear liquid obtained was 7.42 NTU.

Jan 1, 2014

By G. E. Blight

Wind erosion can be a major cause of the loss and dispersion of tailings material from a tailings dam into its surrounding environment. Such dust dispersion can be a serious nuisance, as well as a health hazard to inhabitants in nearby settlements, and can also damage the health of animals, degrade crops, making them less marketable, and cause soil and water pollution. The problem of wind erosion can affect tailings dams in all types of climate, but becomes worse as climatic aridity increases. Because clouds of dust are often observed billowing across the top surfaces of tailings dams in dry windy weather, there is a common misconception that the dust arises from wind erosion of the top surface. As a result, much effort and money is vainly spent on treating the tops of tailings dams to prevent dust generation, whereas the slopes of the dams are the true major dust source. This paper briefly reviews what is known of erosion of tailings dams and then proceeds to describe the mechanics of wind erosion in general, and how it affects tailings dams in particular. Finally, recommendations are made for mitigating wind erosion of tailings dams and the resulting blowing dust.

Jan 1, 2007

By T. Tholana, P. N. Neingo

"Mining companies globally are currently facing severe economic and financial challenges. In addition to global challenges, the South African mining industry has to face other operational challenges that are unique to the country and which threaten the survival and competitiveness of the industry. Profit margins are being squeezed by rising costs and decreasing commodity prices, while labour productivity is greatly affected by intermittent labour unrest. This paper analyses how the South African gold mining industry has performed pre-, during, and post the global financial crisis of 2008. The competitiveness of the industry in terms of labour productivity and industry cost curve position is analysed for the period 2006–2013 to assess the impacts of both the global financial crisis and labour unrest. An analysis of the South African gold mining industry is presented at company as well as mine level. Productivity measure in this paper is limited to labour productivity, in line with limited reporting on productivity. All the data analysed was obtained from the public domain. IntroductionSouth Africa dominated the world as the number one gold producer until 2009 when China took that position, and today South Africa ranks fifth after China, Australia, Russia, and the USA. According to Statistics South Africa (2009), South Africa still had about 30 years of production in the gold sector, a forecast that fluctuates based on the day’s modifying factors. Although South Africa has a comparative advantage in terms of minerals endowment, there are challenges faced by the mining industry that hinder translation of the comparative advantage into a competitive advantage. The industry continually seeks to address these challenges to remain competitive in global markets while addressing national and community needs.Neingo and Cawood (2014) argued that stakeholders in mining are continually concerned with mine management’s ability to translate use inputs effectively into quality outputs. They further suggested close monitoring of effective utilization of people, materials, and money to obtain maximum production of commodities under given conditions. Productivity is measured in various ways, including unit cost, output per employee, and output per unit capital equipment"

Jan 1, 2016

By J. W. Klokow, K. L. Riemer, R. I. L. Ferreira

As a result of the increased depth of mining in the South African gold mining industry mining induced seismicity is a severe problem. One of the strategies within the industry to contain the problem is to incorporate a system of regularly spaced stabilising pillars into mine layouts. At the Driefontein Gold Mine a system of closely spaced dip pillars is used to contain seismic energy emissions. Comparisons of seismic data for several mining clusters initially indicated a possible measure of success in the containment and occurrence of larger events. A detailed analysis of data over a 5-year period since the start of mining however, has revealed a delayed seismic response to the increasing strike spans. Significant changes marked by an increase in certain seismic variables have been observed at mining spans of between 100 to 120 meters and could be of significance to pillar spacing in the design of deep level mining layouts. La sismicité occasionnée par l’exploitation minière est un problème grave dans les mines profondes de l’industrie minière aurifère en Afrique du Sud. Une des stratégies utilisées dans l’industrie a été de maîtriser le problème en incorporant un système de piliers de stabilisation régulièrement espacés dans la disposition des mines. A la Driefontein Gold Mine, un système de piliers de pendage proches les uns des autres est utilisé pour contenir les émissions d’énergie sismique. Au début, des comparaisons de donnés sismiques pour plusieurs groupes d’extraction ont indiqué un succès possible dans la limitation et l’occurrence d’évènements sismiques. Cependant, une analyse détaillée des données sur une période de 5 années a révélé un délai entre la progression de l’extraction et une réponse sismique accrue. Des changements considérables dans les variables sismiques ont été observés dans des intervalles d’extraction entre 100 et 120 mètres, ce qui pourrait être significatif pour l’espacement des piliers dans la conception de la disposition des mines de fond. Resultierend aus den zunehmenden Tiefen des Bergbaus in der südafrikanischer Goldbergbauindustrie stellt sich die vom Bergbau hervorgerufene Seismizität als bedrohliches Problem dar. Es war eine der Strategien innerhalb der Industrie, das Problem dadurch einzudämmen, daß regelmäßig plazierte Stabilisierungspfeiler in den Bergbaulayouts inkorporiert wurden. In der Driefontein Gold Mine wird ein System von knapp aneinandergesetzten im Abfallbereich befindliche Pfeiler benutzt, um seismische Energieemissionen einzudämmen. Vergleiche der seismischen Daten für mehrere Bergbaugruppen zeigten anfangs ein mögliches Maß von Erfolg in der Eindämmung und im Auftreten von größeren Fällen an. Eine ausführliche Analyse von Daten über einen 5jährigen Zeitraum hat jedoch ergeben, daß eine Verzögerung zwischen der Progression des Bergbaus und einer erhöhten seismischen Reaktion besteht. Bedeutende Änderungen in den seismischen Variablen wurden an Bergbauspannen von 100 bis 120 Metern beobachtet und könnten für Abstandsbemessung von Pfeilern im Design des Tiefbergbaulayouts von Bedeutung sein.

Jan 1, 2003

By H. Yavuz

Closed form solutions assume opening shape to be circular to simplify the calculation of the ground response curve for the design of underground openings. However, in mining and civil engineering works, non-circular openings are commonly excavated. Therefore, there is a need to estimate the ground response curve for such openings. In this respect, a simple model for circular, arch and rectangular shape underground openings subject to a hydrostatic stress field is the aim of this study. A comprehensive numerical modelling, using the finite difference method, based on numerical modelling code FLAC version 4.0, was carried out. In addition to shape of an opening, the effect of rock mass strength, opening size, in situ stress on strain (tunnel deformation to tunnel radius) of the opening in response to applied support pressures was investigated parametrically by developing models for each specific condition. The strain results for each excavation shape obtained from this large number of models against the normalized strength of rock mass and internal support pressure with in situ stress magnitude were evaluated by multiple regression analysis. As a result, a model that was well correlated to data was developed for an overall estimate of the ground response curve depending on relevant effecting parameters. The regression coefficients of the model were given for estimating both roof and sidewall response curve of each excavation shape. The model was verified by statistical tests and by an analytical solution. Diagrams were also established to highlight the influence of relevant parameters and to estimate the support pressure for a stable opening staying within the acceptable limits of strain. Strains occurring in a rectangular opening are found to be larger than those in the arch and circular openings for the other fixed parameters. In the mean time, larger strains occur around an arch shape opening than a circular opening.

Jan 1, 2006

By J. A. Luckmann

"SynopsisThe purpose of this paper is to introduce an innovative approach to risk management in surface mining operations, namely, positive risk. Traditionally, risk management focused on mitigating losses (negative). Positive risk, on the contrary, reverses the approach and focuses on exploiting a project’s inherent benefits (positive).The inability to accurately determine project objectives during the project planning phase and the failure to achieve those objectives during the execution phase is a major problem for any project management in the mining environment.The advance of computer aided design models for mine planning enables mining engineers to examine various options within a very short time. Employing positive risk management combined with drivers-based risk management when evaluating these options provides an ideal opportunity to investigate areas for improving the mining project’s profits. Furthermore, harnessing positive risk returns during the planning phase contributes immensely to the successful achievement of project objectives.Mining has inherent business risks, which can appear overwhelming when considering the risks associated with a mining project schedule, cost, and safety or resources, etc. The question is – how to manage risks in a surface mining environment, and what process methodologies, work methods, processes, and standards should be used when considering the surface mining risks. Applying the principles of positive risk management to manage surface mining risks is not only relevant, but definitely beneficial to mining projects and to the mining industry as a whole.It would be beneficial for risk managers and risk professionals to understand the roles of positive risk ‘drivers’, also known as ‘propitious attractors’. Identifying, analysing, estimating, and understanding the propitious attractors, their behaviour and their influence on project risk events helps considerably during the planning and execution phases. The theoretical and practical knowledge of both sides of the risk – the downside risk (negative risk) and upside risk (positive risk) – can add substantial value to any organization when downside risk is adequately mitigated and upside risk is beneficially exploited."

Jan 1, 2015

By I. Soto, E. Córdova, A. Anani

The new caving megaprojects that are planned to go into production in the next decade have scheduled horizontal developments at very high rates, which are difficult to achieve. Research has been conducted that seeks to model the construction times for underground developments to determine the feasibility of achieving the planned rates. However, these previous attempts do not consider all the operational aspects that make up the mine development cycle. Here, we present a discrete event simulation (DES) model that individualizes each unit operation of the development cycle to determine the construction rates that new projects will be able to attain. The developed model was applied to the New Mine Level (NML) of the El Teniente Division (DET). The results indicate that it would be impractical to achieve the advance rates scheduled in the original plans if the unit operations of the mine continue to be executed using the status quo. The metres developed after six years in the sections analysed can be significantly improved by changing the maintenance strategy for the equipment (457 metres increase), orepass availability (194 metres increase), and the initial planning sequence (1 598 metres increase). It is recommended that the mine implements a flexible maintenance strategy, defines a strategy to ensure and increase orepass availability to contractors, and makes use of current simulation tools for a more robust development sequence planning.

Oct 1, 2022

By N. Sahay

Open fire in coal mines is one of the most serious threats to miners, as well as to the mine. Open fire can often be effectively dealt with by prompt local action, otherwise it very quickly becomes uncontrollable. In one incident, none of the available open fire control technologies, viz., water deluge and sprinkler systems, high-expansion foam, high-pressure high-stability nitrogen foam, water misting, and ventilation and pressure control techniques, were effective for saving the mine without sealing from surface, since the fuel-rich environment prohibited underground access due to the methane explosion hazard. The authors have developed a methodology for dealing with advancedstage open fires underground by the application of a modified ventilation control technique. It is based primarily on a better understanding of the behaviour of open fires, proper diagnosis of the problem, application of judicious ventilation control techniques, and selection of suitable fire indices for assessing the status of an open fire. This methodology was used to successfully control an open fire in Surakachhar 3 and 4 incline mine Surakachhar, central India. The fire area was sealed underground and production subsequently resumed in record time. The paper discusses the behaviour of open fires, particulars of the mine, diagnosis of the problem, experimentation methods, and the results obtained.

Jan 1, 2014

By A. Mainza

It is common practice in the mineral processing industry to use hydrocyclones for particle classification. However, classification in the UG2 platinum circuits using the hydrocyclone poses major challenges due to the differences in density between silica and chromite, the two major components of this ore. Silica, the PGM carrying component, has an average density of 2.7 and the barren chromite component has an average density of 4.5. When conventional and flat bottom cyclones are used there is a misplacement of particles due to differences in density leading to inefficiencies in the classification by size. As a result of the density effect, coarse silica reports to the overflow, resulting in loss of recovery, and fine chromite reports to the underflow, resulting in loss of milling capacity and unnecessary production of fine chromite. A classifier based on a different concept was required in the classification of UG2 platinum ore. The three-product cyclone, which is a hydrocyclone with two concentric vortex finders to produce three distinct products, has been tested in the UG2 ore application and indications are that misplacement of particles due to differences in the component densities can be minimized through the use of this unit. Industrial and pilot plant trials were conducted and indications are that the three-product cyclone can be installed to selectively produce a middlings stream that can be screened using Pansep screens to provide a screen oversize, which is predominantly coarse silica that can be preferentially reground to recover the PGM values contained in the coarse silica.

Jan 1, 2005

By W. S. Steinberg

In 1963, the full-scale engineering study for the development of an iron, steel, and vanadium plant was initiated. This was the birth of Evraz Highveld and its process flow as it is known today. Highveld started out as a steelworks that produced steel and vanadium-bearing slag from a titaniferous magnetite iron ore mined from its own mine site near Steelpoort. The process utilized co-current rotary kilns for prereduction, and submerged-arc furnaces for the production of pig iron with approximately 1.15% vanadium. Because of various technical challenges that the submerged-arc furnaces experienced over the years, a decision was taken in 2004 to convert the furnaces to open slag bath (OSB) operation, in order to enable the maximum production of iron and vanadium while improving the control over operational parameters. The conversion proved to be highly successful and, since 2005, three furnaces have been converted to OSB operation. The fourth furnace will be converted in the first half of 2011. The conversion to OSB furnaces not only yields higher vanadium recovery to the metal at the iron plant, but also improves the overall throughput of the steel plant. This is the result of the higher carbon content of the liquid iron from the OSB furnaces, eliminating the need for anthracite addition to the shaking ladle process. This reduces the blowing time by approximately 60%. The conversion of the furnaces to OSB configuration is seen as an enabling technology change and a prerequisite to the implementation of other plant improvements that are envisaged. The long-term vision of EHSV is to convert five furnaces to OSB mode, and permanently decommission the two remaining submerged-arc furnaces. This will allow EHSV to maintain current steel and vanadium production but at a significantly improved overall efficiency.

Jan 1, 2011

By M. S. P. Rampedi

The paper reports on a vacation work project conducted at Khuseleka No. 1 Shaft, Anglo Platinum, where there was a need to optimize the transport of personnel to level 15 and below. Approximately 900 men per hour need to travel between the shaft and the start of the current chairlift system. Time studies were used as the major indicator of the extent of the current problem, and it is recommended that a new chairlift system be installed to cover the distance from the vertical shaft station at level 15 to the chairlift decline station on level 15. A capital cost of approximately R10 million is necessary to carry out the proposed recommendation. Khuseleka No. 1 Shaft has the capacity to wind 1070 people per hour, and the current labour complement going to the level 15 shaft station stands at 1570 employees; thus at optimum efficiency the proposed chairlift system could transport the entire shift to the start of the current chairlift system in only 1 hour and 45 minutes. Reducing the distance walked at the start of the shift may also have an impact on productivity.

Jan 1, 2012

By A. Bothma

The Impala No. 1A ventilation shaft is located approximately 15 kms north of Rustenburg and is accessed via the R510road from Rustenburg to Northam/Thabazimbi. This situation is shown on the location plan in Figure 1. The geology at the site consists of an upper layer of black turf of about 1 metre in thickness, grading into weathered norite. The depth of weathering is generally less than 5 metres. Zones of deeper weathering may occur along fracture zones associated with faults and dykes. Groundwater occurs mainly within the weathered/fractured aquifer system. The ventilation shaft is a 5.1 m diameter upcast shaft ,and forms part of a system of ventilation shafts to complement the existing infrastructure as mining progresses down the new twin decline extension of Impala 1 shaft. The principal reason for these shafts is to lessen the risk of an extended RAW and also to counter the effects of the heat build-up as the mining goes deeper, with the resultant effect that the existing cooling centre (fridge plant) becomes more remote from activities. The No. 1A shaft (upcast) is positioned approximately 1,2 km on down dip from the main shaft and the No. 1Bshaft (downcast) approximately 1,2 km further. Geological information was used from a borehole 1,2 km away on strike from the upcast shaft. The first shaft (1A) is a 5,1 m diameter hole to be fitted with two 2,2 MW fans, whilst the second shaft (1B) is 4,1 m diameter to accommodate a 7MW fridge plant.

Jan 1, 2001

By Masanobu Masukawa, Toshio Shiota

The shaft-type ferromanganese smelting furnace (SF) at Mizushima Ferroalloy Co., Ltd. has been in operation since startup in 1985 and is continuing to perform smoothly. Production has been increased from the original design capacity of 270t/d to 350t/d by various operational improvements. As a productivity index of the shaft-type furnace, production of 350t/d is equivalent to productivity of 0.9t/m3/d (daily production/cubic capacity of furnace). Recently, various operational improvements were implemented to achieve productivity of 1.0t/m3/d or higher, including oxygen enrichment operation, increased tapping frequency, maintenance of the throat profile, and operation with small lump coke. The target productivity of 1.0 t/m3/d was achieved in January 2005. This report describes the improvements introduced as part of this high productivity technology.

Jan 1, 2007

By P Knight, P A. Walker, H E. Speight

Pushback 8 South is the final cut back on the south wall of the East Pit at BHPBilliton?s Mt Whaleback iron ore mine in the Pilbara region of Western Australia. Development of the cutback commenced in 1999 and is now nearing completion with ultimate pit walls up to 300m high. This paper describes the geotechnical, structural and hydrogeological setting of PB8S, reconciliation between design and slope performance and the slope engineering techniques used to effectively manage the risks associated with the slope. These techniques include slope buttressing and sequential mining with waste backfilling, as well as a detailed program of displacement and hydrogeological monitoring, structural mapping and slope stability assessment. During the course of slope formation recent developments in remote slope displacement monitoring using radar and remote structural mapping using terrestrial photogrammetry have also been applied. Aspects of the PB8S slope management plan are relevant to many large scale open pit slopes. This paper provides geotechnical practitioners with information which may be helpful in managing geotechnical risk in similar environments.

Jan 1, 2006

By B. Ulrich

The basis of this paper is a compilation of work in the design and construction of copper heap leach facilities, and interviews with various heap leach operations personnel in Chile and Peru. The purpose is not to highlight specific mines and their performance, but rather to discuss geotechnical/civil features of copper heap leach facilities that function well, as well as features that do not. During the 1990s several copper heap leach facilities were brought on-line in South America. Many of these facilities have now been operational for a number of years during which time the operators have been able to monitor the performance of their heaps. This paper serves as a compilation of operators? experiences, and provides a discussion of the lessons learnt over the past decade. Several key geotechnical issues are examined, focusing upon the integrity of the ore, drainage material and pipe network, along with the success of inter-lift liners. This conference provides a timely update of the original paper (Burkhalter et al, 2002).

Jan 1, 2003

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

The roasting of sulphide ores and concentrates is often the first step in the production of metals or chemicals. In many processes, the production of sulphuric acid is viewed as a by-product, while in some plants production is an important economic factor. Regardless of the purpose, a pyrite roasting plant consists of mainly three plant sections: roasting, gas cleaning and sulphuric acid. With the addition of air, the pyrite concentrates are transformed into solid oxides and gaseous sulphur dioxide at temperatures of 600 - 1000° C. After cleaning and cooling, the sulphur dioxide in the roasting gas is further processed to sulphuric acid. Two types of reactors are used depending on the application: stationary or circulating fluid bed . For over 60 years, Outotec has progressively been developing the principle of fluidised bed technology in several different reactor types for a multitude of process applications. The versatility of the fluidised bed reactor system has manifested itself in the treatment of minerals, including solid fuels, and for metallurgical processes both in the ferrous and non-ferrous fields. Process applications have included roasting, calcining, combustion and charring of coals, as well as off-gas treatment. This paper provides a summary of the pyrite roasting technology currently used along with a simple cost comparison of pyrite roasting and sulphur burning processes.

Jan 1, 2009

By D. P. Roberts

This investigation aimed to simulate the experiments performed by Nic Gay (Gay, N.C. 1976. Fracture growth around openings in large blocks of rock subjected to uniaxial and biaxial compression. International Journal of Rock Mechanics and Minining Sciences and Geomechical Abstracts, vol. 13. pp. 231-243) on fracture growth around openings in blocks of rock subjected to uniaxial and biaxial compression, using the Elfen discrete element code. The results of the physical experiments indicated a number of trends that were successfully replicated in the numerical simulations, including crushing ahead of the face, the formation of a sub-vertical tensile fracture at centre-span, the formation of groups of fractures originating from the crushed face zone, the formation of large corner-to-corner fractures which precede sample failure, and linking of slot corner and sample corner fractures leading to sample failure. In addition, other features were apparent that were not reported by Gay. It is believed that these took the form of conjugate shear fractures (as reported by Gay in a previous paper) and other features that may have been altered or inhibited by the presence of pre-existing structure in the physical samples. It was found that the samples, though nominally made up of the same rock type, must have had significantly differing properties. The presence of pre-existing structures may have contributed to this discrepancy. Strain measurements from the physical experiments were reasonably well matched, except where the gauge lay directly in the path of advancing fractures.

Jan 1, 2012

By S. Badr, R. Mendoza, M. U. Ozbay, M. D. G. Salamon

ABSTRACT: The use of coal pillars at depth is fraught with problems due roof control difficulties and the possible occurrence of coal or pillar bumps. In the USA the largest and most important application of pillars at depth is in longwalling, where chain pillars are the customary supports of the multiple entry developments. At first, the chain pillars were designed using conventional approaches, where the principle is that the strength of the pillar should exceed the load imposed on it. Such approach to design led to larger and larger pillars at great depths, but instead of eliminating, it tended to aggravate the roof control problems. Eventually the idea was born that small sized yielding pillars, which have proved to be successful elsewhere, might provide the answer to this pressing problem as well. The aim of this paper is to study the modes of pillar failure at great depths, using two solution methods. The first of these comprises some elementary solutions obtained with the aid of a simplified conceptualization of the rock mass. This model consists of a strain-softening coal seam sandwiched between two stratified masses. The second approach utilizes FLAC3D, which is a commercially available three-dimensional numerical modeling software package. To gain a better insight, both the strain-softening and ideally plastic Mohr-Coulomb constitutive laws embodied in FLAC3D were exploited. As expected, the width to height ratio of the pillar has proved to be the primary factor that determined the behavior of the pillars. Narrow pillars fail in a stable manner without the occurrence of instabilities. Intermediate w/h ratio pillars under the appropriate loading conditions, may fail suddenly and may even collapse totally. Squat pillars do show the potential for sudden, coal bump like side failure, but because the remaining large width of the inner core, the ruble around the pillar provides sufficient confinement so as to reestablish stability. Finally, the study revealed that the traditional Mohr-Coulomb law does not provide a useful insight into the failure of coal pillars. RESUME: L’utilisation des piliers de charbon dans les mines souterraines de grande profondeur occasionne des problèmes due aux difficultés de control de plafond et possibles fracture ou explosions au niveau des piliers. Aux Etats-Unies d’Amérique, l’utilisation des piliers dans les mines souterraines de charbon comme moyen de support est considèrees comme étant la plus grande et la plus importantes des méthodes utilisée dans le ‘’ longwalling method’’ ou une série des piliers sont disposé de manière à supporter les multiple entrées d’exploitation de charbon. En premier lieu, cette série des piliers étaient construit de manière conventionnelle avec un principe basé sur le fait que le poids exerce sur les piliers doit être inférieur a la force que ces piliers exerce sur le plafond. Ce principe a conduit a ce que le volume des piliers augmente au fur et à mesure que la profondeur au de la mine augmente. Malheureusement, au lieu de résoudre le problème de support, ce principe n’a fait qu’aggraver le problème de contrôle de plafond. Eventuellement une idée s’est dégagé allant du fait que les piliers endommagés de taille moyenne qui se sont avérés être efficaces ailleurs, pourraient fournir un indice à ce particulier problème. Le but de cette recherche est celui d’étudier les différent types de ruptures qu’un pilier peut occasionner lorsqu’il est utilisé a grande profondeur, tout en utilisant deux possible méthodes. La première d’entre elle comprend quelques solutions élémentaires obtenues avec l’aide d’une méthode simplifié et conceptuelle de la masse de la roche. Ce modèle consiste à prendre en sandwich la bande de minerais de charbon entre deux masses stratigraphiques sans pour autant endommager le plafond. La seconde méthode nécessite l’utilisation du ‘’ FLAC3D’’, qui est un logiciel commercialisé disposant d’un modèle numérique en 3 dimensions. Dans le but d’obtenir

Jan 1, 2003

By N. McEwan

Keywords: refractories, chromite, Marico This paper examines the role of refractory-grade chromite in refractories. The chromite deposit at Verref?s Marico Chrome mine is described. The refractory properties of chromite and their role in basic refractories are described. The properties and metallurgical applications of chrome-containing refractories are described and finally environmental issues associated with chrome-containing refractories are discussed.

Jan 1, 2011