Search Documents

The National Institute of Occupational Safety and Health has classified diesel exhaust as a potential human carcinogen. Though standards for diesel particulate matter (DPM) in the work place have not been established, concern for the health of miners is prompting mine operators to consider methods for reducing worker exposure to diesel exhaust. Approach One of many methods for reducing DPM being investigated by the Bureau of Mines is the use of additives in diesel fuel to improve combustion. Research Results Three fuel additives have been tested in Caterpillar and Deutz diesel engines which are similar to types used in underground mines. One iron-based additive containing ferrous picrate had no effect on emissions. A second iron-based additive containing ferrocene reduced DPM between 5 and 45 pet depending on engine operating conditions. The 37-pct reduction for an 8-minute duty cycle, which includes a wide range of transient loads and speeds, is considered to represent in-mine performance.

Jan 1, 1990

By M. J. Ferrante

New data on zirconium tetraiodide (ZrI4) have resulted from high-temperature enthalpy and X-ray powder diffraction studies conducted by the Bureau of Mines. These studies were undertaken as part of the Bureau's efforts to provide important thermodynamic data essential to the advancement of mineral resources technologies that can be employed with minimal energy requirements and minimal environmental degradation. Enthalpies were measured with a copper-block drop calorimeter. No transitions or other anomalies were found. Tabulated values are given from 298.15 to 772 K for relative enthalpy, heat capacity, entropy, and Gibbs energy function. Enthalpies are expressed in equation form and combined with data from the literature to calculate values of the standard enthalpy of formation and the Gibbs energy of formation. X-ray powder diffraction data indicate that ZrI4 is primitive cubic with a lattice parameter of 11.79 A and is isostructural with stannic iodide (SnI4).

Jan 1, 1980

By John C. Machisak

THIS CHAPTER of the Minerals Yearbook relates to employment data and injury experience in the metal, nonmetal, and quarrying industries. Combined statistical data on the mineral industries as a whole can be found in volume Ill. Each industry in the chapter is shown separately, and no attempt has been made to combine and show an overall picture. The voluntary reporting of data on injuries and employment by operators of metal and nonmetal mines and quarries has contributed substantially to the promotion of safety in these industries. Data on injury and employment in the clay mining and milling industry are included for the first time. Table 6 contains data for clay mines only for 1955 and for clay mines and mills for 1956. The clay-mill figures are included with other nonmetallic mills in table 5. The information for norunetallic mills was compiled and published for the first time in the 1955 issue of this report.

Jan 1, 1958

By Fred N. Kissell, J. E. Matta, J. C. LaScola

The methane gas emitted from coal samples collected from the conveyor belts dumping into silos was measured by the Bureau of Mines. Approximately 50 pct of the total gas desorbed into a sealed can within 1 week was released during the first 24 hours. No simple correlation between the gassiness of the coal stored and the methane concentration in the silo open space above the coal was found. This was probably because the gassier coals were stored in open-top silos, which were better ventilated. Although the methane concentration in the open space above the coal pile was less than 1 pct for all 34 silos investigated, a methane measurement in the coal pile showed that high methane concentrations can exist. The methane released in the pile appears to accumulate and not liberate freely into the open space above the coal pile. Probably this gas is released during reclaiming operations, but further research is required to substantiate this claim.

Jan 1, 1978

Determine safe practices for surface mine blasting near pressurized gas, oil, and water transmission pipelines. Background Surface mine blasters regularly have to address the issue of how blasting affects transmission pipelines that run near and sometimes through their permit areas. Regulatory approaches to blasting have ranged from no regulation at all to strict limits intended to prevent cosmetic cracks in plaster interior walls of homes, but they have not directly addressed the impact of blasting on nearby pipelines. Concerned with both productivity and safety, the mining industry and its regulators have requested guidance on safe practices for mining near pipelines. The Pipeline Research Group of the American Gas Association has sponsored studies of the effects of small close-in blasts because of vibration concerns related to the installation of new pipes into existing pipeline right-of-ways. By contrast, the recent study in which the U.S. Bureau of Mines (USBM) took part is the first addressing large-scale mining blasts.

Jan 1, 1995

By James R. Means, George Bowser

A new phone system was developed that provides eight full duplex communications channels over a single twisted shielded phone line, with no central switching station or line amplifiers. This system greatly simplifies installation and maintenance over that required with conventional switching systems. The system is based on microprocessor technology and digital frequency synthesis. Frequency division multiplexing is used over a bandwidth of approximately 300 kHz, and a baseband voice channel (compatible with conventional pager phones) is provided as a backup to assure communication if the multiplex features fail. Multiplex operations are controlled over a 30-kHz digital channel. The system is designed to operate with up to 16 km (10 miles) of cable plant and a maximum phone separation of 8 km (5 miles). The digital techniques permit a limited amount of monitoring and control capability to each phone. This consists of two pair of contact inputs or outputs, to be used as desired. These "flags" may be read or controlled by a dispatcher's phone.

NIOSH recommends that exposures to respirable coal mine dust be limited to 1 mg/m3 as a TWA concentration for up to 10 hr/day during a 40-hr workweek, measured according to current MSHA methods (see Section 5.1 and Appendix J). NIOSH recommends that sampling be conducted with a device that operates in accordance with the NIOSH accuracy criteria [Busch 1977; Busch and Taylor 198 11 and the international definition of respirable dust [ACGIH 1994; CEN 1993; IS01993; Soderholm 1991a,b; 1989].* The REL represents the upper limit of exposure for each worker during each work shift. For single, full-shift samples used to determine noncompliance, NIOSH recommends that MSHA make no upward adjustment of the REL to account for measurement uncertainties [NIOSH 1994c] (see also Section 5.6.2). NIOSH further recommends that all reasonable efforts be made to reduce exposures to respirable coal mine dust below the REL through the use of engineering controls and work practices.

Jan 1, 1997

By Maria I. De Rosa

The U.S. Bureau of Mines performed experiments to determine if the primary gas toxicities evolved during the early (-300° C) and later (>400° C) combustion stages of mine conveyor belts could be predicted by a smoke particle characteristic. The experiments were conducted in an approximately 20-L furnace at set furnace temperatures of 150°, 250°, and 1,000° C, with a furnace airflow of 10 L/min. The variables studied, as a function of time, included hydrogen chloride and carbon monoxide concentrations, the average smoke particle diameter (d8 and number concentration (no), and the product of the average smoke particle diameter and concentration (dgn0) Other variables included the sample and furnace temperatures and the sample mass weight loss. Results show that the inverse of the smoke particle diameter-concentration product (ldgn0), correlates directly with the hydrogen chloride and carbon monoxide toxicities released in large quantities during the early and later stages of combustion.

Jan 1, 1989

By G. M. Molinda, J. P. Ulery

Since 1970, abnormally high methane emissions have been observed in eastern sections of the Federal No. 2 Mine operating in the Pittsburgh Coalbed in northern West Virginia. The nature and volume of these emissions indicate a source other than the coalbed. An investigation was undertaken to delineate probable methane sources. Gas well information and stratigraphic correlation of corehole data indicates that a sandstone directly above the main coalbed is an additional source of methane emissions. The sandstone body appears to be an ancient stream channel, infilled with fine-grained sand and organic matter. Coalification of the organic matter produced methane as a byproduct. Additional methane presumably migrated into the sandstone unit from the subjacent coalbeds. The methane became trapped in the porous clasticunit by the surrounding impermeable strata. Mine development near this unit creates a significant pressure gradient, triggering abnormal methane emissions into the mine along naturally occurring fractures. Pre-development methane drainage of the sandstone could be accomplished by completing vertical boreholes along its trend.

Jan 1, 1984

By R. L. Anderson

Mechanical cleaning of bituminous coal in the United States was begun about 1875, with plants in western Pennsylvania and Illinois. The United States Geological Survey began to record the quantity of washed bituminous coal in 1906; and the series was carried forward to 1923, except that no data were collected, for 1922. This statistical work was transferred to the Bureau of Mines in 1925, and the collection of data on mechanical cleaning was resumed in 1927. Data collected before 1927 include only the coal that was washed at the mines and do not include that cleaned by pneumatic methods at the mines and that cleaned at central washeries operated by consumers.2/ The total bituminous coal washed in 1906 was less than 10 million net tons. In 1927, the first year for which complete figures are available for all types of mechanical cleaning, 28 million net tons of bituminous coal were cleaned in the United States.

Jan 1, 1951

By Robert J. Timko

The objective of this Bureau of Mines research work was (1) to determine how well the E. I. Du Pont de Nemours and Company P-2500 personal dust sampling pump controls the flow rate at 2 L/min and (2) to compare respirable dust mea-surements made using the P-2500 with those made using a nonpulsating sampling flow system, both using the Dorr-Oliver 10-mm nylon cyclone dust size classifier. The calibrator and the operation manual for the P-2500, supplied by the manufacturer, were also evaluated. Flow tests consisted of long-term (6-to 8-hour) flow stability tests at various backpressures, a low-flow indicator examination, flow controller response time tests and pulsation tests. Dust tests were performed using coal, silica, and Arizona road dust. No tests were performed to examine effects of temperature, barometric pressure, vibration, or mechanical shock. These pumps performed well within manufacturer specifications in all tests.

Jan 1, 1982

By W. L. Dare

The Federal Bureau of Mines is publishing a series of studies on the methods and costs of mining uranium on the Colorado Plateau. This report describes the longwall-mining methods and techniques used at the Radon mine, Big Indian district, San Juan County, Utah. The tabular Radon ore body lies on the southwest flank of the Lisbon Valley anticline, strikes N. 10° W., dips 7° SW., and has an average thickness of 4-1/2 to 5 ft. The mine is developed by a three-compartment vertical shaft, a haulage level driven beneath the ore, and a system of drifts driven within and parallel to the strike of the ore.

Jan 1, 1961

This Part is concerned with the theoretical study of UHF radio communication in coal mines, with particular reference to the rate of loss of signal strength along a tunnel, and from one tunnel to another around a corner. Of prime interest are the nature of the propagation mechanism and the prediction of the radio frequency which propagates with the smallest loss. Our theoretical results are compared with measurements made by Collins Radio Co. This work was conducted as part of the Pittsburgh Mining and Safety Research Center's investigation of new ways to reach and extend two-way communications to the key individuals that are highly mobile within the sections and haulage ways of coal mines.

Jan 1, 1974

By Murray Jacobson

The respirable dust standard in the Federal Coal Mine Health and Safety Act of 1969 is designed to prevent disability and death from coal workers' pneumoconiosis. Beginning June 30, 1970, the operators of coal mines were required to maintain the average concentration of respirable dust in the active workings at or below 3.0 milligrams of dust per cubic meter of air. The standard is reduced to 2.0 milligrams per cubic meter after Dec. 30, 1972. This paper presents the equipment and procedures used by the coal mine operators in implementing the respirable dust sampling program established by the Secretary of the Interior and the Secretary of Health, Education, and Welfare and shows the effect of the law, during the first year, on the reduction of dust levels in selected mines. The system employed by the Bureau of Mines for analyzing and processing the dust samples is also presented.

Jan 1, 1971

The first phase of our work for PMSRC on this contract was devoted to a comprehensive and in-depth assessment of electromagnetic (EM) noise measurements and data taken by several contractors for use in the design of operational and emergency mine communications. Pertinent measurements and data of other selected investigators were also included in the evaluation. This assessment treated the measurements and instrumentation used, the data analysis and presentation methods, and the utility of the final results. This phase concluded with the identification of the most useful results and methods, the remaining data gaps, the contractor most qualified to fill these data gaps, and the definition (with PMSRC and this contractor - NBS, National Bureau of Standards) of a follow-on noise measurement program, instrumentation system, and data processing methods tailored to obtain the necessary but missing noise data. A partial bibliography of references related to electromagnetic and seismic noise and propagation in the frequency bands of interest was also compiled during this first phase. The body of this Part of the final report presents a summary of the findings of our EM noise assessment, together with detailed recommendations regarding the new noise measurements to be taken and the instrumentation and data processing methods to be used. This work was done during the latter part of 1971 and the early part of 1972. During subsequent phases of the contract ADL was asked to perform on-going evaluations of the continuing program of electromagnetic (EM) noise and propagation measurements made by Bureau contractors, and to utilize pertinent data from these measurements to make performance estimates for

Jan 1, 1974

By C. Lorimar Colburn

"The use of helmets during the war has accentuated interest in the advisability of using stiff hats in mines to protect the miners against falling rocks. About forty per cent of the accidents in mines are due to falling rocks or roof. A large number of these accidents could be prevented if the miners wore stiff hats or helmets.The use of head protective devices in minas is not new, for they have been in use for many years in Europe and in the Lake Superior District in the United States. In practically all of the mining districts in Europe stiff hats of some kind are required by the mine management. George S. Rice, chief mining engineer of the Bureau of Mines, reported that in Germany, Belgium, and France stiff hats made of papier mache or felt rosin are in use. Similar hats are generally employed in the Lake Superior District. In building the subways of New York and Philadelphia it was the practice of engineers and workers to let the hair grow very long and to wear a close fitting cap or felt hat. In Germany the hats are high like the military helmets, whereas in France and Belgium they fit more closely to the crown. In England the practice is mixed. As a rule the miners use soft padded caps, but in Yorkshire many of the miners use sole leather, tight-fitting caps of jockey pattern with the seam forting a little ridge down the middle of the cap. These hats are very useful allow thin beds of coal, as in crawling one is very likely to strike his head a sharp piece of rock or on a timber. Of course, such mishaps are more likely to occur to a man not familiar with the mine. It must be admitted such hats do not stick on well, though this is usually due to their not being especially fitted. The German hat is particularly unsuited to an American-shaped head.It is interesting to note that on the continent tight cotton caps are generally worn over the hair and under the hard hat. This is a measure for cleanliness which is excellent. In low beds of coal share much crawling on hands and knees is necessary the dirt and coal dust sift down, making the miner black and dirty. In metal mines stiff hats are of especial use in shaft work; also in raises or high stapes. A small fragment of rock falling some distance either down a shaft or raise would kill a man if it struck him squarely on the head. A stiff hat or helmet may protect him and save his life. At a station in a shaft where men are loading the cage or skip, some kind of adequate head protector should be compulsory. A head-protecting hat or cup which is also a good insulator should be worn where there is danger of striking one's head against a wire carving an electric current."

Jun 1, 1920

By Scott Turner

We have gathered here in Pittsburgh, at the Nineteenth Annual Safety Congress, in order to advance the cause of safety. Although my personal inter- est in this movement alone would have been sufficient to insure my presence here, specific duties have brought me to this congress in an official capacity. My responsibilities as the head of the United States Bureau of Mines, which makes the promotion of safety in the mining and allied industries one of its major activities, necessitate my attendance. My obligations as president of the Joseph A. Holmes Safety Association, an organization closely allied to the bureau and which has for one of its objects the public recognition and reward of outstanding achievements in safety, require that I be present at this time. This morning, my job is to present the Holmes safety certificate to the Lehigh Portland Cement Co. First I will remind you of the nature of this safety association, named in honor of the first director of the Bureau of Mines. After Mr. Holmes' death, in 1915, a number of influential organizations banded together to commemorate the name of this leader in the conservation of human life. In order that you may appreciate the significance of an award by the Joseph A. Holmes Safety Association, I shall read you the list of 24 national organizations which comprise its membership:

Nov 1, 1930

By A. T. Iannacchione, D. G. Puglio

This Bureau of Mines study covers 25 underground mines that were active in the Upper and Lower Freeport and Lower Kittanning coalbeds in 1976. The coal ranges from low to medium volatile in rank; its primary use is for steam generation. Seven mines emit more than 100,000 cfd of methane gas; those mines are the deepest and largest producers. The methane gas content of three core samples of the Lower Kittanning coalbed was estimated by the direct method. A sample from a depth of 320 feet contained 0.5 cu cm of gas per gram, at 620 feet there was 0.8 cu cm of gas per gram, and at 1,060 feet there was 11 cu cm of gas per gram. These results suggest that methane control problems will be encountered in the future as deeper coal is mined.

Jan 1, 1979

By Geo S. Rice

"The most authoritative compilations on the coal resources of the British Isles are given in ""The Coal Resources of the World"" issued by the 12th International Geological Congress, 1913. The reserve, calculated to a depth of 6,000 feet, in seams containing not less than two feet of merchantable coal are as follows: Mining at present is conducted at depths from about 800 to 3500 feet. The shallower coals have largely been exhausted. The present average hoisting depth probably is about 1500 feet.The thickness of individual beds at present mined varies from about 2-1/2 feet up to 40 feet in thickness, the latter thickness being found in North Staffordshire. The coal is rarely found level, but is approximately level in some parts of Yorkshire. Anthracite is mined in limited quantities in Wales, and Wales also produces a very high grade semi-anthracite or smokeless coal, which is fa famous the world round, and is equaled only by the Pocahontas and New River coals in the United States:As concerns the methods of mining, these vary widely according to the pitch of the bed, the thickness of coal, and natural conditions, but the prevailing method is some form of longwall or semi-longwall, by which all the coal is extracted. The other principal method is a so-called pillar and, stall method, by which the coal is mined out, leaving square or rectangular pillars which are extracted on the retreat, making it virtually, a retreating longwall system. This method is applied where the roof is strong, and particularly in the thicker beds, as the longwall method is not so well adapted for mining where the thickness exceeds five or six feet, unless it is what is called a multiple seam, one in which there are partings of rock that provide material for building walls, which the roof in subsiding gradually squeezes down."

Jul 1, 1920

By Gene Asai

Properties obtained for columbium carbide-carbon castings ranging in car-bon content from 12 to 17 weight-percent were compared with those of hot-pressed composites of similar composition. The properties were oxidation resistance in static air between 500° and 700° C, linear thermal expansion between 20° and 2,400° C, electrical resistivity between 20° and 1,500° C; microhardness between 20° and 1,500° C, and modulus of rupture between 1,300° and 1,800° C. CbC-C castings differed markedly from hot-pressed material with respect to microstructure, electrical resistivity, and modulus of rupture, but behaved quite similarly with respect to oxidation resistance, thermal expansion, and hot hardness. In oxidation resistance, thermal expansion, and hot hardness both materials were independent of carbon content. Both castings and hot-pressed composites oxidize rapidly in air above 600° C, have thermal expansion coefficients very similar to columbium metal, and the logarithm of the hardness decreases linearly with increasing temperature. The microstructures of hot-pressed composites contained varying amounts of graphite in a CbC matrix but did not contain significant amounts of a eutectic structure present in all castings, nor did they contain graphite needles which were present in the hypereutectic castings. The higher electrical resistivity of hypereutectic castings over hypereutectic hot pressings was attributed to the presence of highly oriented graphite needles in the castings. The modulus of rupture of castings was 1-1/2 to 2 times that of hot-pressed composites. Both materials displayed bend ductility above 1,800° C.

Jan 1, 1971