Search Documents

By G. Dale Cor, Will H. Coghill, M. F. Williams, I. L. Feld

"INTRODUCTION During the past several years the Southern Experiment Station of the Bureau of Mines, with the cooperation of the University of Alabama, has given attention to hydraulic classification. One of the things this work has revealed is a variability not generally recognized in the conditions of teeter at different depths. This report depicts the passage of material through a teeter column and its emergence as a classified product.The work was made possible through the development of a classifier for several hundred pounds per hour permitting a small quantity of coarse spigot material to be discharged without the usual interruptions caused by stop-pages. Previous designs of small classifiers have been unsatisfactory because the,orifice used to control the quantity of spigot product as subjectto stoppages, particularly when attempting to discharge a small quantity of although the classifier used in this work has been described in detail in a previous publication 6/ its principal features will be discussed briefly herein. The main subject matter of the paper is based upon the three figures that illustrate in panorama the conditions that exist in a classifier during the continuous classification of bituminous coal, anthracite coal, and an iron ore trailing."

Jan 1, 1946

By Richard L. Unger

The U.S. Bureau of Mines has designed, fabricated, and tested a prototype track maintenance vehicle for underground coal mines. The vehicle uses a stiff rotating brush to clean the track so that a visual inspection is possible. It is also equipped to measure track gauge and cross-level. The objective of this report was to describe the track maintenance vehicle and detail the results of investigations into present underground track inspection procedures and cleaning technologies, which led to the development of the prototype. Recommendations are made concerning the integration of components of this prototype vehicle into current track cleaning and inspection systems used in underground mines.

Jan 1, 1984

By E. D. Gardner

About five minutes after 3 o'clock on Thanksgiving morning, November 24, 1927, smoke was discovered coming up No. 2 shaft of the Magma Copper Co.'s mine at Superior, Pinal County, Arizona. Of the 49 men in the mine at the time, 42 were able to make their way to the outside unassisted, but 7 perished. Six bodies were recovered, and the seventh, that of an Apache Indian cage-tender at No. 2 shaft, is thought to be in the caved section between the 1,600 and 2,250 foot levels A second and independent fire broke, out in No. 1 shift about 2 a.m., November 27, burning .out the shaft timbers from the surface to the 200-foot level and destroying the surface fan and structures. About 20 men were underground fighting the fire in No. 2 shaft, but all were safely withdrawn, aril the fire in No. 1 haft was quickly controlled.

Jan 1, 1928

By J. M. Singer

The objective of this investigation was to determine minimum air velocities and entrainment rates for coal and rock dust dispersion in wind tunnel experiments under conditions that simulate dispersion from surfaces in coal mines where airflows are induced by weak gas explosions. Dust deposits were bed-or ridge-shaped; particle sizes were 6 to 80 microns (cohesive deposits) or 100 to 150 microns (free-flowing deposits); and wind tunnels were 7.62 cm wide by 5.08 cm high by 300 cm long, and 2.4 m wide by 1.5 m high by 215 m long. The investigation showed that minimum air velocities (directed at mid-height) of separate, layered, or mixed piles of coal dust and rock dust were within the range 5 to 30 m/sec, independent of size of wind tunnel. This finding considerably facilitates scaling of data to mine-size passageways. Free-flowing deposits dispersed relatively slowly by single-particle detachment; cohesive dusts dispersed faster by the breaking and lifting of large clumps along weak failure flames; particle dispersion occurred in flight. Layered or mixed deposits of coal and rock dust did not disperse selectively. Semiempirical expressions were derived relating minimum air velocities and dispersion rates to dust-pile geometry, cohesion, porosity, and bulk density.

Jan 1, 1972

By I. O. Salyer

This research was conducted with the objective of suppressing the respirable dust in coal mines by foam application. A formulation was developed for making a water-based, high-expansion, and limited stability foam. A horizontal boring machine was used as a laboratory coal mining model for generating coal dust. A modified laboratory foam generator was built. Foam was applied directly to the point at which dust was being formed by the cutter of the boring machine working against a block of coal. Coal dust was sampled with an impinger and analyzed for the particle count and particle size distribution. Coal dust suppression test results on freshly generated dust have demonstrated very clearly that in laboratory scale experiments over 90% of the respirable coal dust can be suppressed by foam. These tests were run when initial coal du t concentrations were 10 and 70 million particles per cubic foot (mppcf).

Jan 1, 1970

This report presents a Bureau of Mines study comparing the construction costs, leakage measurements, and predicted performance of different types of large stoppings built and tested in a room-and-pillar oil-shale mine. The six full-sized structures (30 ft high by 55 ft wide) included both permanent and temporary stoppings and were fabricated using materials ranging from structural steel to coated brattice cloth. Leakage across each stopping was measured at differential pressures ranging up to 1.0 in w.g., using both the brattice window method and sulfur hexa-fluoride (SF6) tracer gas. Blast air pressures resulting from a full-scale face blast of approximately 1,800 lb of ammonium nitrate-fuel oil (ANFO) explosives were measured across two of the stoppings and the pre-and post-leakage rates were compared for all the stoppings. Overall performance of the stoppings for production applications was evaluated using an operational model of a two-panel oil-shale mine. Different combinations of temporary and permanent stoppings were evaluated based upon ventilation performance and construction and operating costs.

Jan 1, 1988

By P. Kovalchik

The Bureau of Labor Statistics (BLS) classifies hearing loss as a separate illness category. Hearing loss accounted for 11% of all illnesses in 2005 (U.S. Department of Labor Bureau of Labor Statistics, 2006a). According to occupational data for coal mining provided by the Mine Safety and Health Administration (MSHA) from 2000 to 2005, operators that exceeded 100% noise dosage were from only seven types of machines: auger miners, bulldozers, continuous mining machines, front end loaders, roof bolters, shuttle cars (electric) and trucks (Title 30 CFR Part 62, 2000-2005). Roof bolting machine operators rank second among all underground machine operators that exceed 100% noise dose. There are approximately 600 underground coal mines with 3,930 roof bolting machine operators (U.S. Department of Labor, Mine Safety and Health Administration, 2005; U.S. Department of Labor Bureau of Labor Statistics,

Jan 1, 2008

By David E. Morse

Burundi, a small central African republic located between Tanzania and Zaire, remained essentially a nation of small family farms in 1978-79 with approximately 95% of the population engaged in subsistance agriculture. Coffee and tea continued as the nation's major export commodities. Mineral exports, small tonnages of cassiterite, wolframite and bastnasite, accounted for an estimated 3% of total exports in 1978 and 2% in 1979, or $2 million2 in both years. Burundi's major mineral imports in 1978-79 were cement, iron and steel, and refined petroleum products. Abnormal weather conditions, a drop in world coffee prices in 1978, and the conflict in neighboring Tanzania and Uganda in late 1978 and early 1979 combined to re-strict economic growth in Burundi during 1978-79. The gross domestic product (GDP) posted a gain of 6.7% in real terms for 1978 and an estimated 2.5% for 1979 which was significantly less than the 13.7% recorded in 1977, a time of high world coffee prices. The manufacturing and construction sectors were hard hit in 1979 by the conflict between Burundi's eastern neighbors because of transport disruptions which made building materials and manufacturing inputs almost unobtainable.

Jan 1, 1981

By Janke L. W. Jolly

Owing to an upsurge in export earnings. Cameroon made substantial economic Progress in 1978 and 1979. With a real growth estimated at 6%, the gross domestic product (GDP) for 1979 surpassed $5 billion.2 Crude petroleum production was providing a new potential in 1978 and 1979 for achieving national self-sufficiency. Among other benefits, crude petroleum exports were helping to offset the escalating costs of refined petroleum imports and to reduce the 14% to 17% annual rate of inflation. Over the 4 years prior to 1978, Cameroon's petroleum imports increased by 12.1% in volume annually, while the import cost increased by 24.5% annually to about $105 million. Total export earnings for 1978 were $805 million,3 to which crude petroleum contributed $25.3 million and crude aluminum product exports contributed $25.9 million. Petroleum exports had increased to about $240 million in 1979 and were in third place after coffee and cacao. Total imports for 1978 were valued at nearly $1 billion. The volume of petroleum imports decreased in 1979 to 552,000 tons, compared with 622,000 tons in 1978. The European Economic Community (EEC) countries purchased over 75% of total Cameroonian exports and provided most of the Nation's imports. The United States purchased $12.4 million in petroleum exports from Cameroon in 1978. Domestic consumption of aluminum metal from imported Guinean alumina continued. to grow; thus exports of this metal to France (valued at $2 million in 1978) and Japan

Jan 1, 1981

By G. Esterhuizen, C. Karacan

Methane can be a significant hazard in coal mine longwalling operations and extensive methane mitigation techniques are employed by coal mine operators. Reservoir modeling techniques are used to better understand the liberation and migration of methane from the surrounding rocks towards the mine ventilation system. The caved rock behind the advancing longwall face, known as the gob, can contain high void ratios, providing high permeability flow paths to the methane. The gob is progressively compacted by the weight of the overburden, resulting in a reduction in the void ratio and associated permeability. Estimating the permeability distribution within the gob poses challenges due to its complexity. The authors have developed a new methodology to determine both horizontal and vertical variations in the permeability of the gob. Variations of the permeability in the vertical direction are based on a model of caving and block rotation, which considers the effect of block dimensions and fall height on the void ratio. Gob compaction by the overburden and associated permeability changes are determined from a three-dimensional geo-mechanical model which simulates the gob as a strain hardening granular material. The resulting three-dimensional permeability distribution in the gob is then transferred to a reservoir model. The paper demonstrates the application of the method and shows that reasonable results are obtained when compared to empirical experience and measurements.

By R. Hogg, J. M. Mutmansky, E. Kaya

"Characterization of the size, shape, chemical composition, and mineralogical content of mine airborne dusts generally requires a larger mass of dust particles than is typically collected using traditional sampling devices. In this paper, the general design of a passive dust collector is described and the field results are presented. The collector was constructed of galvanized sheet metal duct with a resin-coated honeycomb to provide an elutriation-type system for particle collection. Several versions of the collector were used in the field portions of the research.The dust samples collected from underground coal mines were found to possess angular particle shapes, relatively consistent size distributions, and elemental compositions that showed relatively little variation, at least for the more prevalent elements. In addition, the distributions of particles sizes obtained from the passive dust collector appear to be similar to those of samples collected at the same time in a conventional personal sampler except that the passive device seems to collect a larger quantity of coarse, nonrespirable particles. Conclusions on the suitability of this dust collector for collecting characterization samples are presented. In addition, the potential for using such a dust collection system for supplying dusts for biomedical research is discussed.INTRODUCTIONRecently, a considerable amount of research effort has been directed toward better understanding of the characteristics of the coal dust generated during the mining process. It is generally believed that dust characteristics play a significant role in the development of Coal Workers' Pneumoconiosis (CWP). In order to effectively protect coal workers from coal dust, it is important to understand the properties of dust, the mechanisms of generation and dust-lung reaction. Conducting research on dust characterization, dust control and the biomedical aspects of dust toxicology generally requires a large sample of airborne coal dust. Unfortunately, current dust sampling instruments are not able to meet this demand because only a few milligrams of dust are collected."

Nov 1, 1995

By Andrew B. Cecala

The U.S. Bureau of Mines has designed and tested a system called the Bag and Belt Cleaner Device (B&BCD) to reduce dust levels in and around the bag conveying and stacking process. The device physically cleans either 22.7 kg (50 lb) or 45.4 kg (100 lb) paper bags by using a combination of brushes and air jets. It is completely self-contained and is kept under negative pressure by a baghouse to ensure that dust and product removed from the bags during cleaning does not flow into the work environment and contaminate workers. The bags travel through the device on a chain conveyor, which permits any product or dust cleaned from the bags to fall into a hopper at the bottom of the device and be recycled back into the process via a screw conveyor. Once exiting the B&BCD, the outside of the bags and the conveyor are essentially product and dust free. The B&BCD was evaluated at two mineral processing plants to determine reductions with the device in use. The results of both field evaluations showed that the amount of product removed from the outside of the bags varied from 77 to 93 pet.

Jan 1, 2010

By David C. Oyler

The U.S. Bureau of Mines and the United States Steel Corporation evaluated the progress of methane drainage at the Oak Grove, AL, degasification pattern. Coalbed pressures were monitored between December 1981 and November 1985. Formation pressures, in the lower bench of the Mary Lee Coalbed, were reduced from 400 lbf/in2(ga) in 1977 to 50 lbf/in2(ga) in November 1985. Gas contents of coal cores obtained from monitor wells were compared with coalbed gas contents measured in 1976. Data indicated a 48- to 56-pct reduction within the pattern and a 29-pct reduction at a point 500 ft outside the pattern. The effect of the advance of a section of the Oak Grove Mine on changes in gas and water production rates in the pattern was evaluated. Gas production increases were noted in 12 wells; water production decreases were noted in 6. The times of initial influence indicate the presence of a zone of high permeability within the pattern. This zone correlates well in orientation and location with a fracture zone mined through at the mine. The existence of such fracture zones could have a significant effect on productivity of individual coalbed methane wells.

Jan 1, 1989

By A. Adams

The Bureau of Mines determined the composition of the vapors liberated during thermal decomposition of aluminium nitrate nonahydrate. Small samples were heated from room temperature to 5500 C with initial heating rates from 500 to 2000 C/min. Gases were rapidly swept away from the heated chamber with Ar and subjected to immediate analysis in order to minimize reaction between the components. In addition to H20, four N-containing compounds were identified: HN03, N02, NO, and N20. Nz could not be determined in the presence of the nitrogen oxides, and at-tempted separation from the oxides led to the formation of more nitrogen. Relative amounts of each component were found to vary over a period of time; however, total amounts measured with different heating rates were reasonably constant and were typically as follows: 84.2 pct HN03, 7.1 pct N02, 4.3 pct NO, and 4.2 pct N20. HN03 and NO were determined from chemical reactions with a permanganate solution, N20 was measured with a mass spectrometer, and NO2 was measured with a spectro-photometer. Details of the methods used are described. Since NO2 and NO can readily be converted to HN03, about 96 pct of the N from the decomposition can be recovered as HN03

Jan 1, 1987

By L. H. Adami

This paper reports the results of solution calorimetry conducted to obtain the heats of formation of crystalline FeS04?6.952H20 and FeS04?1.008H20, from. which values were derived for the stoichiometric compounds FeS04?H20 and FeS04?H20. Also included are derived values of the free energies of formation and dehydration. This work was undertaken primarily to fill a need for data for pure, easily obtainable ferrous compounds that are suitable for use as calorimetric intermediates, The ferrous sulfate hydrates meet the essential requirements for this use.

Jan 1, 1963

By Jürgen F. Brune, R. Karl Zipf, Michael J. Sapko

Seals are barriers constructed in underground coal mines throughout the United States to isolate abandoned mining panels or groups of panels from the active workings. Historically, mining regulations required seals to withstand a 140-kPa (20-psig) explosion pressure. However, the Mine Improvement and New Emergency Response Act (“MINER Act”) requires the Mine Safety and Health Administration (MSHA) to increase this design standard by the end of 2007. This report provides a sound scientific and engineering justification to recommend a three-tiered explosion pressure design criterion for new seals in coal mines in response to the MINER Act. Much of the information contained in this report also applies to existing seals. Engineers from the National Institute for Occupational Safety and Health (NIOSH) examined seal design criteria and practices used in the United States, Europe, and Australia and then classified seals into their various applications. Next, the engineers considered various kinds of explosive atmospheres that can accumulate within sealed areas and used thermodynamic calculations and simple gas explosion models to estimate worst-case explosion pressures that could impact seals. Three design pressure-time curves were developed for the dynamic structural analysis of new seals under the conditions in which those seals may be used: unmonitored seals where there is a possibility of methane-air detonation or high-pressure nonreactive shock waves and their reflections behind the seal; unmonitored seals with little likelihood of detonation or high-pressure nonreactive shock waves and their reflections; and monitored seals where the amount of potentially explosive methane-air is strictly limited and controlled. Figure 1 is a simple flowchart that illustrates the key decisions in choosing between the monitored or unmonitored seal design approaches and the three design pressure-time curves. For the first condition, an unmonitored seal with an explosion run-up length of more than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections exists. The recommended design pressure-time curve rises to 4.4 MPa (640 psig) and then falls to the 800-kPa (120-psig) constant volume (CV) explosion overpressure. For unmonitored seals with an explosion run-up length of less than 50 m (165 ft), the possibility of detonation or high-pressure nonreactive shock waves and their reflections is less likely. A less severe design pressure-time curve that simply rises to the 800-kPa (120-psig) CV explosion overpressure may be employed. For monitored seals, engineers can use a 345-kPa (50-psig) design pressure-time curve if monitoring can ensure that (1) the maximum length of explosive mix behind a seal does not exceed 5 m (16 ft) and (2) the volume of explosive mix does not exceed 40% of the total sealed volume. Use of this 345-kPa (50-psig) design pressure-time curve requires monitoring and active management of the sealed area atmosphere. These design pressure-time curves apply to new seal design and construction.

Jan 7, 2007

By C. B. Manula, R. L. Sanford, R. A. Rivell

PART I. FLOW CHARTS

Jan 1, 1974

By Takashi Ohya, George V. Keller, Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a rela- tively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurements of ambient surface electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal-to-noise ratio at the surface. Numerous C.W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surface magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null in the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

By A. W. Ambrose

"Those having an intimate knowledge of the relation between production and consumption of crude oil in the United States have realized for some time that production will not be able to keep pace with consumption. The American public has had this called forcibly to its attention by the increased prices of gasoline and crude oil, and by the recent shortage of gasoline on the Pacific Coast. In substance, each year we are consuming millions of barrels of oil more than we produce, and this deficit must be made to by importations. A careful analysis of the situation makes it evident that we need every barrel of oil that can be produced.Need for the Petroleum Production Engineer.Under present production practices perhaps 80% of the oil still remains in the sand. (See Lewis, J.O., Methods for increasing the recovery from oil sands, U. S. Bureau of Mines, Bulletin 148 p. 8.) Many wells are making water, and even whole pools are being flooded. The burning of fuels under field boilers is not generally efficient, and often gas is not made to do its full duty in bringing the oil to the well.In the past the producer has had to combat these and other problems single-handed. He has been too busy to give them special attention, and he has had little competent engineering advice. Oil, gas, and water occur underground according to certain natural laws. Undoubtedly an engineer, who is familiar with production practices and understands the fundamentals of the accumulation of oil and gas, can be of service to the producer by specializing on certain problems with a view of getting mare oil from the sand. In every other enterprise of similar magnitude the engineer is regarded as a necessary unit to its operation, and he should be so in the production of oil. His field of work should extend to every phase of production in which science and engineering and geology"

Sep 1, 1920

By A. W. Ambrose

A few years ago, (March 3, 1915) Congress passed a law providing for the establishments of ten mining experiment stations under the supervision of the Bureau of Mines. In 1917 the Secretary of the Interior decided that one of these stations should be devoted to Petroleum, and in the early part of 1918, approved the establishment of the Petroleum Experiment Station at Bartlesville, Oklahoma, upon the condition that the city furnish the site for the buildings and guarantee $50,000. for the erection of the buildings. A building site of 5 acres and the necessary building fund was furnished by the Bartlesville Chamber of Commerce.The buildings consist of an administration and laboratory building, both of brick construction. The former is a two-story structure of eight rooms. A large room occupying over half of the main floor is devoted to the library, reception room, and clerical force. The remaining rooms comprise a drafting room and six offices occupied by the staff assigned to this station. The laboratory is a one-story brick building and contains a well-equipped chemical and physical laboratory, also a machine shop and mechanical laboratory. In addition to the main buildings there now are on the property an experimental refinery, a blue-print house, and a store house. These latter buildings are all of sheet-iron construction.

Oct 1, 1920