Search Documents

By Robert Stefanko

Transients are results of sudden changes which take place in power systems and can be created by the opening and closing of switches and circuit breakers or the occurrence of a fault anywhere in the complex. Transients are of short duration, and the time during which they occur is an extremely small percentage of the total operating time. However, it is during these short periods that the greatest electrical stresses occur, mainly due to excessive currents or voltages. In extreme cases, system parts are damaged, and equipment failure follows. Safety can be further compromised because anomalous voltages can exist at machine frames. For several years, the electric utilities have been well aware of the serious nature of transients on their systems, but problems firmly believed to directly result from these phenomena are just now becoming apparent to the coal mining industry. The situation became discernible after the underground introduction of high voltage distribution systems (along with vacuum circuit breakers) and sensitive solid state electronic apparatus. In order to protect against such transients, knowledge about their characteristics and origin must be obtained.

Jan 1, 1974

By H. E. Powell

The magnetic susceptibilities of 57 minerals containing titanium, zirconium, vanadium, columbium, tantalum, chromium, molybdenum, and tungsten were determined. The source and petrographic analysis of each sample are given. Included are values for isomorphous series of minerals showing wide ranges of composition and for a few high-purity synthetic minerals.

Jan 1, 1968

By Eugene T. Sheridan

The 23d annual survey of the peat industry by the Bureau of Mines, United States Department of the Interior, revealed that 75 producers in 17 States re-ported commercial production of peat in 1956. Forty-seven producers reported humus production, 19 reported reed-sedge peat, 17 reported moss peat, and 1 reported muck. This total exceeds the number of active operations, but several producers reported recovering more than one type of peat. Fifty-five percent of the total production was reported as peat humus, 30 percent as reed-sedge peat, and 15 percent as moss peat. A negligible amount was reported as other types. More than one-fourth of the total output was raw peat with no preparation, other than having been air-dried. The remainder consisted of processed peat prepared for use by cultivation, shredding, or kiln drying.

Jan 1, 1958

By J. Mutmansky, C. Lee

"The size distribution of coal mine dust is one of its most important characteristics because the particle size is known to govern the region of deposition of dust within the human respiratory tract. In addition, dust characteristics, particle settling rate, transportability of the dust and the efficiency of dust control measures are all affected by the particle size. As a result, particle size distribution of the airborne dust in a coal mine is a fundamental property that impacts on the health of underground workers.This paper deals with some basic findings on the size distribution of cool mine dust based upon the results of data collection in six underground coal mines using continuous miners. All airborne dust sampling was performed on development sections using eight stage cascade impactors and permissible 2. O l / min pumps. Samplers locations were fixed in the sections with respect to the continuous miner and roofbolter or with respect to the intake and return airways • Sampling times varied from 45 minutes to 6 hours , depending upon the dust concentration. The first topic of analysis was the test to determine whether the commonly used lognonnal distribution is valid when applied to airborne coal mine dust. Secondly, the conventional method of representing the· distribution using two parameters, the geometric mean and the geometric standard deviation, is questioned. Since almost all size data were found to show some degree of bimodality, the two parameter lognonnal distribution may not represent the total airborne coal mine dust size , quite adequately. Bimodal lognonnal distribution was tested to be a good approximation in the case with two modes in the size distribution.The final topic discussed in this paper is the 'locational variation of the airborne dust size distributions within the continuous mining section. The size distributions varied considerably at the different sampling locations with the continuous miner and roofbolter producing the coarser distributions. Fine size modes in the range of 2 to 4µ m including mostly respirable dust particles were present in almost all samples • Second dust generating sources such as the shuttle car movement were found to be major causes of high respirable dust concentrations in some cases ."

Jan 1, 1988

By Frank G. Horino

This report describes an instrument designed by the Bureau of Mines for quantitatively identifying texture of rock surfaces produced by grinding or extremely rough surfaces beyond the range of commercial surface measuring instruments. The transducer for the instrument is a linear variable differential transformer that converts mechanical motion caused by surface roughness, waviness, and lay to an electrical output. The electrical output is recorded graphically as an X-Y plot of the line traversed on the rock surface. Details of the synthesized device and its calibration are given. The sensitivity of the unit is 2 percent of the scale setting of the amplifier. The horizontal scale is adaptable from ¼ inch to 15 inches of specimen length with a sensitivity of 0.01 inch if a 10 to 1 magnification is used and 0.1 inch if a 1 to 1 magnification is used.

Jan 1, 1968

By J. D. Marchant

The Bureau of Mines studied solid-state electromigration to determine the value of the technique as a method of purifying cerium metal. Cerium metal in bars 6 inches long and 1/2 inch in diameter was refined at 600° C by solid-state electrolysis to remove iron, copper, and manganese. Iron and manganese were electrotransported to the anode and copper was electrotransported to the cathode. The concentration of iron at the anode of a cerium bar was 800 times greater than the concentration at the cathode. The concentration of manganese at the anode was twice the value at the cathode. The concentration of copper was 170 times greater at the cathode than at the anode. A radiotracer technique was used to follow the iron migration in the cerium metal. Molybdenum, silicon, and aluminum impurities were not electrotransported.

Jan 1, 1967

By Paul M. Tyler

Syria is a federation of States under French mandate , comprising the Republic of Syria , the Lebanese Republic or Great Lebanon ( Grand Liban ) , the State of the Alouites , and the Djebel Druse Territory . Beirut is the center of government for the whole area , about 60,000 square miles . Syria is essentially an agricultural country . There is little manufacturing ; and with the exception of the production of asphalt and salt , the mineral industries have not yet risen to commercial importance . Whether this condition is due to a dearth of workable deposits or merely to insufficient exploration is not apparent . The mineral resources , as reported by various authorities , include asbestos , asphalt rock , bitumen , chromite , coal , copper , gold , gypsum , iron , lead , magnesite , manganese , marble and other building stones , nickel , ocher , pandermite ( a hydrous borate of calcium) , petroleum , phosphate rock , pyrite , salt , silver , sulphur , tin , and titanium ( ilmenitic beach sands ) .

Mar 1, 1933

By Arthur J. Hudson, Lawrence W. Scott

The performance of RETIMET metal foam as a flame arrester on explosion-proof enclosures was investigated by the U.S. Bureau of Mines both in laboratory tests and at the U.S. Mine Safety and Health Administration's (MSHA's) Approval and Certification Center, Triadelphia, WV. The objective of this research was to develop a permissible pressure vent for use on lightweight, vented, explosion- proof enclosures. In laboratory tests, four grades of RETIMET, a stainless steel foam material, were evaluated: (1) 45 NC-7, (2) 45 NC-13, (3) 80 NC-7, and (4) 80 NC-13. Explosive gas mixtures were prepared by a dynamic flow system. Ignition was by a low-voltage arc. Each grade of RETIMET metal foam successfully arrested the flame front in all methane-air tests. To evaluate RETIMET metal foam on large, commercial size enclosures, a multicompartmented enclosure was designed and tested in MSHA's explosion gallery in Triadelphia, WV. Extensive explosion testing revealed that a minimum vent-area-to-enclosure-volume ratio of 11.33 in2/ft3 is required to keep internal pressure rises below 3 psig. The RETIMET metal foam functioned satisfactorily in all tests as evidenced by the absence of external ignitions.

Jan 1, 1992

By N. S. Dalal, X. Shi

"SUMMARYElectron spin resonance (ESR) measurements provide direct evidence for the involvement of the glutathionyl radical, as well as an isolable Cr(V)-glutathione intermediate in the Cr(VI) glutathione redox reactions. These results indicate a new mechanism for the reduction of Cr(VI) by glutathione in relationship to cellular environment and suggest that synergistic reactions of Cr(V) and GS· might be responsible for the (unexpected) increase in the Cr(VI)-induced DNA-strand breaks at high glutathione levels.INTRODUCTIONWhile the reduction of Cr(VI) by glutathione (GSH) is thought to be a critical' step in the pathogenesis of the Cr(VI)-exposure related carcinogenesis1- 4, the exact reduction mechanism is not yet understood. The following reaction steps have been suggested :(A) Initial step:Cr04 2- + GSH - GSCrOa - (1)(B) At high GSH levels:GSCroa- + GSH - Cr( IV) + GSSG (2)(C) At low GSH levels: GSC rO a - - Cr ( V ) + GS ·(3)Thus far, however, in these reactions, the GS· radical has eluded spectroscopic detection, while the evidence for the Cr(V) formation has been reported positives as well as negative2·. Her~ we present spin-trap ESR evidence for the formation of the GS· radical, and a definitive ESR detection of an isolable cr(V)-GSH intermediate in Cr(VI)-GSH reactions.MATERIALS. AND METHODSESR spectra were obtained at X-band (-9.7 GHz) using a Bruker ER200D ESR spectrometer. The magnetic field was calibrated with a self-tracking NMR Gaussmeter (Bruker, Model ER035M) and the microwave frequency was measured with a Hewlett-Packard (Model 5340A) frequency counter. The spin probes, a-(4-pyridyl-1-oxide) -N -tert-butylnitrone (4-POBN) and 5,5-dimethyl~1-pyrroline-1-ox1de (DMPO) were purchased from Aldrich, K2Cr201 from Fisher and used without further purification. All experiments were done at room temperature."

Jan 1, 1989

By Edward D. Thimons

The Bureau of Mines developed a stopping design that allows the stopping to be blown down by strong blast forces without incurring any permanent damage. Trials with the new stopping, dubbed the quick-fix blowout stopping, have been conducted in the Bureau's Safety Research Coal Mine at Bruceton, Pa., and in two New Mexico uranium mines. Results have been favorable in all cases. Compared with conventional brattice stoppings or wood bulkheads, the quick-fix blowout stopping is easier and less time consuming to install, is easier to maintain, and in most cases is just as efficient an air barrier. There is same indication that the shape of the stopping makes it more resistant to blast fore s than the fabric stoppings now in use.

Jan 1, 1976

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By Michael G. Zabetakis, Israel Liebman, Henry E. Perlee

Flammability studies conducted to date on stratified methane - air and pentane - air mixtures in air indicate that location and extent of a flammable layer are affected by molecular diffusion , gas motion , and propagation of flame . In initially quiescent mixtures , the lower limit - of - flammability zone may be determined by assuming molecular diffusion alone governs mixing rate . The upper limit - of - flammability zone can be predicted in this manner only for stratified layers with small concentration gradients ( less than 0.2 volumepercent per inch ) ; where large concentration gradients are encountered ( for example , as much as 30 volume - percent per inch ) , the initial - mixture methane concentrations that yield flammable mixtures are larger than anticipated . Flames propagating through heterogeneous quiescent methane - air atmospheres in the direction of the concentration gradient exhibit flame speeds at any point that corresponds to the flame speed of the homogeneous gas mixture having the same gas composition as that of the point in the heterogeneous system . In flowing mixtures with large concentration gradients , the degree of mixing prior to ignition does not appear to affect the flame velocity and emitted radiation appreciably in a 6.5 - ft - diameter gallery .

Jan 1, 1964

By J. S. Walker

The Bureau of Mines monitored surface subsidence and water level fluctuations in 10 shallow observation wells above a series of four adjacent longwall panels in southwestern Pennsylvania, for about 4 yr. This study attempted to correlate the changes in the water levels within the observation wells to the measured vertical and horizontal ground movements associated with subsidence. Results of this study indicate that the fluctuation of the water levels appears to be a function of the well location relative to the mine layout and the proximity of mining. Wells are generally unaffected by mining of a preceding panel unless they are located within the angle of draw for that panel. Wells located at the centerline of a longwall panel exhibit the greatest fluctuation and head loss. This relationship may be related to the strain developed by the advancing longwall face. The water levels in the wells monitored fell at the greatest rate when the ground surrounding the well was in tension. The rate of the decline decreased as the dynamic development of the strains was changing from tension to compression. The water levels were found to be near the premining level before the ground was subject to maximum compressive strain. Nine of the ten wells investigated recovered to their premining water level after mining was completed.

Jan 1, 1988

By Laxman S. Sundae

In the vast majority of American coal mines, roof bolt holes are drilled dry, mainly because of mine operator concern with the spent water creating adverse working conditions. Wet drilling, however, can increase drilling rates and the effective lifetime of the drill bits used. This study, carried out as part of an ongoing cooperative research program between the U.S. Bureau of Mines and the University of Missouri-Rolla, shows that the large volumes of water conventionally used in wet drilling are not necessary, and the performance benefits from wet drilling can be achieved with total volume flows on the order of 0.4 L per hole. This conclusion is validated based on the measured respirable dust generated in drilling Berea sandstone. The results are confirmed using a variety of bit shapes, which are also shown to have a significant effect on penetration rate.

Jan 1, 2010

By E. S. Shedd

The Bureau of Mines investigated electrowinning and tapping lanthanum metal from lanthanum oxide in a fluoride bath. The electrolyte was composed of LaF3, BaF2, and LiF. Metal containing 0.2 percent impurities was produced at a rate of over 2 pounds per hour. Principal impurities were carbon, aluminum, and silicon. Low-carbon metal was produced by continually discharging the carbon oxide gases and maintaining 0.1-atmosphere pressure. Anode reactions and cell design were found to be important factors in cell operation. Both frozen electrolyte skulls and tungsten metal crucibles proved satisfactory for collecting the metal and did not react with the molten lanthanum.

Jan 1, 1966

By William H. Schiffbauer, Ph. D. Mowrey

Proximity warning devices can improve workplace safety by alerting workers when they are in a hazardous area near moving equipment. Industrial work sites often present extreme challenges to safety-based proximity warning devices. Many commercially available types of proximity warning sensors and systems can be rendered useless when covered with mud, ice, snow, ore, rock, and other material. The list includes radar, ultrasonic, capacitive, and visual types of sensors and systems. Addressing these shortcomings, NIOSH personnel have developed a patented active proximity warning system called HASARD (Hazardous Area Signaling and Ranging Device) which employs lowfrequency, low-power magnetic fields which are quite impervious to severe environmental conditions. A shapeable wire loop antenna which provides the marker of dangerous work areas, has been mounted on a continuous mining machine and was mounted inside 1.3-cm thick angle iron. This loop antenna was exposed to more than six months of active underground coal production, which included being covered by and scraped over with tons of rock, sprayed by a continuous stream of water, and immersed in thick mud. After six months the loop antenna showed signs of wear, but was still capable of performing its intended function. The HASARD system is now being applied to other industrial applications and is showing much promise, especially in harsh environments. This paper details the system, describes the tests that have been done, and mentions other areas where it can benefit the safety of industrial workers.

By T. A. Henrie, E. K. Kleespies

Electrolytic studies were conducted to determine the transfer rates of the alloying constituents from molten titanium anodes to solid titanium cathodes in molten salt systems . The metals , nickel , tin , copper , bismuth , and manganese , were selected on the basis of thermodynamic data and the melting point of the alloy system . The transfer of nickel , tin , and bismuth was very low . The content of these elements in the cathode was in the range of less than 0.01 to 0.001 percent . The copper transfer was 0.6 to 0.8 weight - percent in electrolytes containing titanium chlorides and 0.12 weight - percent in titanium fluoride salt systems . The manganese transferred at rates comparable to that of titanium . Highpurity titanium and titanium- manganese alloys of uniform composition were produced by electrorefining molten titanium alloys in chloride electrolytes . Comparisons are made between the calculated and the actual quantities of metal transfer .

Jan 1, 1964

By Robert W. Smith

In a certain application2/ it was necessary to compute the beta function B(p, q) for a certain set of values p and q. Since t he set of p and q values was much mo re finely spaced than those in any published tables, the authors decided to make their results available in this report. In connection with this application the functionB(p, q) was needed at various points in the p, q plane at intervals of 0.05, 0.05<p = q< 10.00. Fletcher, Miller, and Rosenhead2/ state that the only tables available in the desired range are those of Rearson.4/ However, the interval used by Pearson was not small enough for the present application. For this reason it was decided to calculate B(p, q) for p = q =0.05 (0.05) 10. 00.2/ This table is published because of the fundamental importance in mathematical analysis of the complete beta function.

Jan 1, 1953

By J. Koster

During the past several years, alunite from the Marysvale (Utah) region has been the subject of investigation by the Electrometallurgical Section of the Bureau of Mines. The nature and occurrence of this mineral, with considerable data on the Utah deposits, together with a number of results of preliminary experiments, have been given in a previous report.6/ The geology of the Marysvale region has been reviewed recently.7/ The present paper reports the results obtained by a method involving the sintering of alunite with boric acid and subsequent treatment of the sinter to produce alumina and potassium sulphate.

Jan 1, 1939

By R. V. Ramani, J. Qin

"During the mining process, the insitu material is broken into different size ranges, from very, large pieces to very fine particles. Some of the fine particles become airborne. In underground coal mining, airborne respirable. dust is associated with health and safety of the miners: The amount and size distributions of airborne dust are important parameters to effective dust control measures. The design of underground mine experiments, including sampling procedures and sample analyses methods to determine these parameters are presented in this paper.. A total of fifteen continuous miner cuts were sampled. The amount of dust generated during the cutting process and the relationship between total and respirable airborne dust concentrations and amounts are examined.The amount of respirable dust airborne is on the average only. 0.016% of the respirable dust generated. On the average, 61% of the total .airborne dust measured is in the respirable size range. The amount of respirable airborne' is on the average 36% of the respirable size fraction in the total airborne dust. For equal proportion of rock and coal material cut, rock contributes about twice as much fines (<0.22 mm) as coal. Additional fundamental research is necessary to further the understanding of 'the airborne propensity of respirable dusts in mine atmospheres.INTRODUCTIONMining is a sequential process of breaking, gathering, loading, and transporting the in-situ .materials.' In underground coal mines, duet in both the non-respirable and respirable size ranges is generated and entrained in every phase of the process. Even though large amounts of dust particles' adhere to run-of-mine coals, part of the dust generated becomes airborne (Cheng and Zukovich, 1973). Studies have shown that bit type affects the amount of dust generated'(Evans and Pomeroy, 1966; Kurth et al., 1975; Roepke et al., 1976; Stecklein et al., 1982; and Khair and 'Reddy, 1986). Deep cutting can reduce airborne dust generation (Black and Schmidt, 1977 arid, Black et 1978). Mechanical properties of. coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable. dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with' data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is'widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism of dust generation and the process by which the generated dust becomes airborne are complex and not yet completely understood coal seams are also important factors in dust generation. Laboratory studies have shown that Hardgrove Grindability Index (HGI) of the coal has a relationship with the amount of respirable dust generated (Beafi and Ramani, 1979; Moore and Bise, 1984; and Moore, 1986). However, these relationships have not yet been validated with data from the mines. The amount of dust airborne depends on a number of factors. Suppression of the airborne propensity of dust by water sprays is widely practiced and is very effective. Water flow rate; pressure and configuration of water sprays have been identified as major factors affecting dust capture by sprays (Courtney and Cheng, 1977; Courtney et al., 1978; and Kissell et al., 1979). Ventilation is a very important means of controlling the dust level at the coal face (Jayaraman, 1977). According to a National Academy of Sciences study (1980), the mechanism"

Jan 1, 1989