Search Documents

By Foster Fraas

A comparison has been made between cubes and spheres in the matrix of the high-intensity wet magnetic separator. For two inclined plane surfaces, such as may occur with cubes, the maximum force value, H [dH-dx] is at the point of nearest approach and is much higher than the force resulting from adjacent spheres. Although the maximum force value for cubes is higher, it decreases more rapidly at increasing distances. The maximum force for spheres is at an appreciable distance from the point of nearest approach. At field intensities for magnetic saturation of the iron spheres, the force extends to further distances with greater uniformity approximating that of the constant force or isodynamic field. The force is also independent of the sphere diameter, which permits the scaling of the sphere diameter to provide changes in particle migration distances without changes in force gradient.

Jan 1, 1972

By James P. Bennett

The U.S. Bureau of Mines investigated the role of imported natural flake graphites in dolomite-carbon refractories used in steelmaking processes and evaluated carbon fibers as a potential substitute. Varying quantities (1.5-30 pct) of natural flake graphite and carbon fibers were added to test samples. The effect of the additions on modulus of rupture (75°-2,750° F), deformation under load (2,750° F), and air-slag-metal resistance (3,000° F) was studied. Carbon purity of natural flake graphite additions did not influence hot strength, deformation under load, or air-slag-metal resistance. When the quantity of 90-pct-carbon graphite addition varied between o and 30 wt pct, hot strength was highest, deformation under load lowest, and air-slag-metal wear the least at 10 wt pct. As test temperature increased from 500° to 2,750° F, the hot strength difference became less. Carbon fiber additions were limited to 1.5 pct in dolomite-carbon brick. At this level, physical properties were generally comparable to those obtained with natural flake graphite, but were below values obtained with 10-pet-f1ake graphite additions. Carbon fibers are not considered a satisfactory substitute for natural flake graphite.

Jan 1, 1989

By Mark R. Pettitt

After a long series of laboratory and in-mine tests, a cost- effective, mineworthy, reduced-noise auger miner cutting head was de signed, fabricated, and field-tested by Wyle Laboratories under contract to the Bureau of Mines. Compared with standard auger cutting heads, the new heads reduced noise by 10 dBA at the jacksetter's position and by 6 dBA at the operator's position. This report contains detailed fabrication instructions, including engineering drawings, that show how a standard auger cutting head can be modified to produce a reduced-noise auger.

Jan 1, 1984

By Philip Thompson

A part of the Bureau of Mines mission is to help improve the Nation's mineral posture by providing the technology for utilizing low-grade ores. In this regard, laboratory testing by the Bureau of Mines has shown that the removal of insoluble slimes using selective flocculation and flotation is a viable method for treating low-grade potash ores that have a high content of water-insoluble impurities. Results indicated that over 82 percent of the insoluble slimes could be removed from sylvinite ore containing 5 percent water insolubles and 13 percent K20 by using nonionic or cationic polyacrylamide flocculants and cationic, anionic, and/or nonionic collectors. Subsequent potash flotation recovered 87 percent of the potash in rougher concentrates containing 57 percent K2O. Sizing and cleaner flotation of the rougher concentrates upgraded the products to 60 percent K2O. Filtration of the water-leached insoluble-slimes flotation concentrates on a bed consisting of leached insoluble-slimes concentrate mixed with potash flotation tailings recovered 80 percent of the brine. Filtration rates using the mixed bed were nine times faster than filtration rates obtained when the insoluble-slimes flotation concentrates were filtered separately.

Jan 1, 1979

By Larry A. Haas

The Bureau of Mines constructed a torsion effusion apparatus to measure the equilibrium vapor pressure of pure metals, alloys, and compounds at temperatures up to 1,500° K. The reliability of the apparatus was established by determining the vapor pressure of silver. The data obtained on solid and liquid silver in the temperature range 1,200° to 1,500° K can be expressed by the following equations:

Jan 1, 1965

By Virgil A. Marple, Susanne V. Hering

"5.1 IntroductionTraditional impactors do not offer much size resolution for submicrometer particles; typically their finest size cut is around 0.4 µ.m. Yet for many aerosol applications it is useful to be able to size segregate aerosols in the size range below 0.4 µ.m. Diesel emissions, welding fumes, cigarette smokes and photochemically generated smog aerosols typically exhibit mass median diameters between 0.1 and 0.6 µ.m. When sampling these aerosols with a traditional impactor, fifty percent or more of the aerosol mass can penetrate the final impactor stage. Allhough the material can still be collected on a backup filter, the filter gives no size resolution. As a result, the investigator has no size information on a substantial portion of the sample. One needs a sampler that size-segregates the majority of the aerosol mass. A lower size cut of 0.1 µ.m or less is required for most combustion smokes and smog aerosol s.To obtain smaller cutpoints two types of impactors have been developed, namely low-pressure impactors and micro-orifice impactors. Both instruments can provide cutpoints as small as 0.05 µ.m. Low-pressure impactors were introduced more than twenty years ago (Stem et al., 1962), and a variety of these samplers are in use today. Micro-orifice impactors have been developed at the University of Minnesota within the last five years (Marple et al., 1981 ). To date theirs are the only examples of these instruments in use.5.2 Operating PrinciplesThe low-pressure and micro-orifice impactors use two different approaches to achieve their very small particle-size cuts. Low pressure impactors resemble ordinary impactors, but are operated at reduced pressures of 5-40 kPa (0.05 - 0.4 atm). They take advantage of the decreased aerodynamic drag on particles that occurs when the mean free path in the air is as large or larger than the particle diameter. Micro-orifice impactors operate at near atmospheric pressure, but employ very small orifices, 40 µ.m to 200 µ.m in diameter. The streamlines of the air impinging upon the impaction plate have correspondingly smaller radii of curvature; the air is accelerated more quickly, making it more difficult for the particles to follow. The basic operating principles for both types of impactors are evident from the particle Stokes number, defined as:"

Mar 1, 1989

By H. Netuka, J. V. Horak, A. W. Khair

"A general review of major problems concerning mathematical modelling of roof bolting problem is given. A mathematical model (MM) of interactive set Bolt - Resin - Rock and its discretization based on the Finite Element Method (FEM) is developed to calculate numerically course of displacement, stress and strain fields in this set. This new MM enables to get also course of the normal and tangential components of contact stress vector, normal displacement and then mutual tangential slip at the bolt - resin and resin - rock interfaces, respectively.Behavior of system on all interfaces is modelled in the MM as a ""unilateral contact"" governed by so called non-classical boundary condition of Signorini's type including Coulomb's law of friction between resin and rock, and ""a given friction"" law between bolt and resin (see Duvaut, Lions (1972) for mathematical formulation).Numerical example and some values of resulting stresses are shown and remarks on necessary and sufficient conditions for solvability of the problem are also given.IntroductionAs is well known roof bolting has become the primary support system in almost all underground coal mines. But the ""theoretical"" design criteria for roof bolt patterns are rather problematic because: "" ... real mechanisms by which the roof bolts reinforce the immediate roof of underground coal mine entry are still relatively unknown"", see Peng (1986).The aim of this contribution is to present brief description of fundamentals of mathematical theory (see Hlavacek et al., 1988) which could be, according to our opinion and knowledge, very helpful for numerical modelling of a such type of problems. For the sake of brevity we restrict ourselves here to just one of the simplest possible problem: analysis of the behavior of interactive set composed by only single full - length - grouted bolt, resin (or cement) and suitable part of domain of a ""immediate"" neighborhood of bolt which should represent physical action of real rock material."

Dec 1, 1995

By Stephen Krickovic

Air quantity-pressure and methane concentration surveys were conducted by the Bureau of Mines in accessible portions of an area being pillared in a Pittsburgh coalbed mine in West Virginia. These included two mined-out and three active butt headings and a bleeder system. The particular mine workings were started in virgin coal directly from a set of main headings; the main reason for the study was the difficulty usually encountered in adequately bleeding the gobs under such conditions. Although the two separate return airways in each active butt heading and the North and 1 Left bleeders contained acceptable methane concentrations (0.01 to 0.78 percent in the butts and 0.73 to 1.0 percent in the bleeders) with significant total methane removal (109 cfm in butts and 631 cfm in bleeders), there were relatively large areas in the gobs with possible minimal airflows. This condition appears to have developed from lack of systematic regulation of the airflow across the gobs and appears to indicate the existence of considerably more methane in the probably low flow areas in the gob.

Jan 1, 1973

By H. L. Gibbs

Many factors contributed to the decision to build a radiochemical laboratory at the Salt Lake City Metallurgy Research Center to investigate the application of radioactive isotopes and chemical compounds in extractive metallurgy. These reasons included the notable success achieved in biological sciences with radioisotopes, the development of reliable instruments and methods for identifying the isotopes and measuring their activities, and the commercial availability of radioisotopes in a variety of forms and known activities. The paramount reason, however, was the realization that better methods were needed for guiding and quantifying research to resolve the complex extractive metallurgy problems under study at the Research Center. This is the first of a series of reports describing the application of radioisotopes and radioactivity techniques in extractive metallurgy. The report includes a discussion of licensing and safety requirements, a general description of the laboratory and the methods used, a definition of the nature and scope of the research program, and a synopsis of the more important problems studied. Subsequent reports will concern radioactive techniques for solving specific problems in mineral dressing, hydrometallurgy, and pyrometallurgy.

Jan 1, 1960

By R. A. Guidotti

The Federal Bureau of Mines studied the thermal decomposition of the nitrides of the Group V A metals (CbN, Ta3N5, and VN) with the goal of preparing high-purity metals. Solid-state purification and arc and electron-beam melting were examined. Electron-beam melting proved to be the most efficient means of nitrogen and oxygen removal. Columbium and tantalum of 99.9-pct purity were prepared by this technique; in the case of vanadium, however, nitrogen could not be reduced below the solid-solution level.

Jan 1, 1976

By J. M. Stuve

Low temperature and high-temperature calorimetric measurements were made by the Federal Bureau of Mines on high-purity samples of Re02(s) and Re03(s) to determine heat capacities and enthalpies. The temperature range of heat capacity measurements was 5 to 310 K for Re02 and 8 to 309 K for Re03. High-temperature enthalpy measurements alone were determined for pure Re207(s,1). The derived standard entropies are S°298 = 11.43±0.01 cal/deg mole for Re02(s) and S298 = 16.55±0.02 cal/deg mole for Re03(s). High-temperature enthalpy equations expressed in calories per mole are as follows: Re02 (s) , H-H298.15 = 16.002T + 1.600 X 10-3T2 + 3.522 X 105T-1 - 6,095 (298 to 1,400 K); Re03 (s) , H-H298.15 = 20.293T + 3.238 X 10-3T2 + 3.950 X 105 T-1 - 7,664 (298 to 1,000 K); Re207 (s) , H-H298.15 = 38.437T + 10.309 X 10-3T2 + 4.315 X 105 T-1 - 13,824 (298 to 413 K); Re207 (s) , H-H298.15 = 30.181 + 17.713 X 10-3T2 - 10,612 (413 to 600 K) ; Re207 (1) , H-H298.19 = 66.101T - 10,092 (600 to 700 K). Gibbs energy of formation (?Gf°) data and related functions over the temperature ranges investigated are tabulated for the three oxides.

Jan 1, 1976

By R. T. Johansen

The wettability of petroleum reservoir materials by water and crude oil has been recognized as an important factor in determining waterflood behavior. The problem of simulating and studying reservoir conditions and characteristics, to produce laboratory results congruous with field experience, has been examined by many methods. (1, 2, 3, 4).4/ The most generally accepted approach to this problem is determining wettability of the porous medium by imbibition methods; or, after solvent extraction, predetermining the wettability of the samples by coating the surface of the medium to render it preferentially oil-or water-wet (3, 5). The emphasis of wettability studies has been placed on the characteristics of the reservoir materials with little consideration being given to the fluids themselves. Therefore, the wetting tendencies of crude oils have been investigated by a recently developed method (6). Imbibition and the more general phenomena of capillary pressure are the most direct ways to measure wettability. The simplest type of capillary pressure observations involves the use of an interfacial-tension capillarimeter, which does not produce as separate values either interfacial tension or contact angle. Actually, these quantities do not have independent significance in reservoir engineering, and the property of wettability they are intended to evaluate is given, immediately by capillarimetric measurements.

Jan 1, 1961

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By Robert E. Meredith, Thomas T. Campbell

An investigation was undertaken to examine the feasibility of employing low- temperature nonaqueous baths for electrodepositing some of the refractory metals of the ferroalloy group . To date , such metals as tungsten , molybdenum , and vanadium have been produced only by high - temperature processes that are technically difficult and sometimes cumbersome in operation . Deposition studies were performed in a wide variety of organic solvents , including amides , ammonia derivatives , ketones , polyhydroxy alcohols , and ethers . Compounds prepared and used as solutes included the chloride and bromide salts of vanadium , tungsten , and molybdenum . Studies were conducted over a temperature range of 20 ° to 200 ° C under inert atmosphere . Conductivity and current potential data were obtained for all baths that contained reasonable solute concentrations . Qualitative solubility data were obtained for compounds of ferroalloy metals in a variety of solvents . In general , all solutes showed low solubility in ethers and ketones but reasonable solubility ( in excess of 20 grams per liter ) in alcohols , amides , and ammonia derivatives . No successful metallic deposits that would encourage further study were obtained with any of the systems that were examined .

Jan 1, 1963

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

By John R. Benham

The West Pioneer RARE II study area, No. 1-006 (fig. 1), has Figure 1.--NEAR HERE a high molybdenum resource potential. Two molybdenum-bearing areas are being explored by Utah International and by Cyprus-Moly Corp, Inc. using geophysical exploration and diamond core drilling. The study area also contains potential resources of gold and silver at six prospects: the Bear Paw (Ibex), Black Bear, Coeur d'Alene, Franklin No. 1, Martin, and Maynard. In addition, the Black Rear and the Martin contain possible copper, lead, and molybdenum resources. Most of the workings are caved.

Jan 1, 1981

By R. D. Govier

The U.S. Bureau of Mines has developed a thin-film X-ray fluorescence technique to rapidly determine Cu, Ni, Co, Fe, and Cr in super alloy leach liquors. Total analysis time per sample was less than 15 min, as opposed to several hours for traditional wet chemical methods. Precision and accuracy were checked by replicate analyses of solutions similar in composition to leach liquors, whose analyte concentrations were well known. Coefficients of variation for all elements were found to be less than 2 pet. With the exception of the results for Fe, all relative errors of estimation were also found to be less than 2 pet. Bulk liquids are not introduced into the spectrometer; thus, the potential for damage to the instrument by leakage of corrosive liquids is eliminated.

Jan 1, 1989

By J. Owens

Advanced materials development ranks as one of the most important high-tech industries of the future in the United States. Recent breakthroughs can be attributed to advanced computer technology, powerful mathematical models, and more precise analytical tools that enable scientists to examine and control properties of materials as never before. Discoveries now being made are providing many industries with opportunities to improve product lines, fabrication techniques, product reliability, and so forth. More¬over, industries, such as space, medicine, and defense, which require stringent: design and perfomance specifications in highly competitive world markets, increasingly demand these new materials. The definition of advanced materials used here is one that has been adopted by the U. S. Bureau of Mines: Those materials which have been developed over the past 30 years or so, and which are being developed at present, that exhibit greater strength, higher strength-density ratios, greater hardness, and/or one or more superior thermal, electrical, optical, or chemical properties, when compared with traditional materials.

Jan 1, 1991

By K. J. Liles

The Federal Bureau of Mines conducts a comprehensive test program on clay and shale at the Tuscaloosa Metallurgy Research Center. All samples are subjected to standard preliminary ceramic tests, which include firing formed briquets at temperatures ranging from 1,000° to 1,250° C to identify firing range and colors, and quick-firing to determine bloating characteristics. Materials that shop potential as structural products are further tested after either extrusion or dry-pressing. If the quick-fire test is positive, bulk samples can be fired in a rotary kiln to evaluate their potential as light- weight aggregate A number of miscellaneous tests also can be conducted if requested. These tests determine properties such as refractoriness (pyrometric cone equivalency), oil-bleaching characteristics, oil absorbency, viscosity for drilling-mud applications, sand-bonding properties for foundry usage, and pelletizing characteristics.

Jan 1, 1977

By Marting J. Gavin

The twentieth century has often been spoken of as the age of petroleum, and from many viewpoints it can be justly considered so. Certainly the petroleum industry is one of enormous importance to this country, industrially, financially, and economically. The United States, however, at present producing over 60 per cent of the world's total output of petroleum, is not producing petroleum at a sufficient rate to provide for its own domestic, consumption. For several years this country has been importing increasing quantities of crude and partly refined oils from Mexico, and has been drawing heavily on domestic stocks of petroleum. Production in the United States is increasing, but it is not increasing at the same average rate as domestic consumption, nor is it probable that in the future domestic production will increase sufficiently to satisfy the demands of domestic consumption, but on the contrary, in the opinion of those best qualified to know, the peak in the curve of domestic production of crude petroleum will be reached in a comparatively few years, whereas the consumption of petroleum and its product will increase at a continually growing rate. This country, then, must turn, and as the increasing imports from Mexico indicate, is turning to other sources than the crude petroleum, produced in this country to make up the deficit between domestic production and domestic consumption of petroleum and its products,

Jun 1, 1920