Search Documents

By Jr. Karr

The Bureau of Mines studied the influence of carbonization method, temperature, and carrier gas on the composition of eight different low-temperature tars produced from a Colorado subbituminous coal. A fluidized bed was compared with an entrained bed, temperature was varied from 500° C to 650° C, and external heating using recycle gas as the carrier gas was compared with internal heating using oxygen-containing gas. The entrained bed yielded significantly more m-cresol and m-ethylphenol, indicating that thermodynamic equilibrium was more nearly approached in the system. Increasing the temperature greatly increased the yield of benzenes and naphthalenes, while paraffins, olefins, and total tar acids were reduced. Using oxygen in the carrier gas decreased the yield of low-boiling phenols and increased that of paraffins and olefins at 650° C.

Jan 1, 1966

By R. F. Stevens

A laboratory method for examining crude shale oil is described. The method uses only about 500 ml. of sample and a limited number of analytical determinations. Results provide information on the general characteristics and composition of an oil and serve as a basis for comparing different oils. However, the method does not provide for direct estimates of yields of commercial products. Analyses of 10 oils produced in the United States by different methods of retorting and of 10 shale oils from commercial-scale operations in 6 foreign countries are given. The shale-oil-analysis method presented in this paper is based on and employs the same equipment as the Bureau of Mines routine method for analyzing crude petroleum. As shale oil contains groups of compounds not generally found in petroleum, several modifications of the petroleum method that might increase its suitability for application to shale oil were investigated. The modifications included in the present method take into account the apparent poor heat stability of shale oil and the presence of large quantities of olefins and nitrogen compounds.

Jan 1, 1952

By Charles A. Seitz

This Bureau of Mines report describes an automatic and continuous transducer-drift compensator. The compensator formed a part of the instrumentation used to indicate the saturation by hydrogen of a cryogenic, adsorption column. It has a variable delayed-response characteristic and will respond only to signals having rise times faster than component drift times. Zero drift due to varying ambient conditions and component aging is nullified. Equations relating the output as a function of the input signal are given.

Jan 1, 1981

By E. B. Nelson, B. W. Gandrud, B. M. Bird

"The Lewisburg No. 2 mine of the Sloss-Sheffield Steel & Iron Company is located in Jefferson County, Alabama, about 7 miles due north of Birmingham. At this point the coal from the Mary Lee seam when coked in by-product ovens yields an excellent quality of metallurgical coke suitable for use in the iron blast furnace; it is also an excellent steam coal. In mining, all three benches are worked. Coarse impurities are largely gobbed by the miners underground.In addition to giving the data obtained from screen-sizing and float-and-sink tests of a representative sample of the raw coal, this report presents the results of slotted-screen tests to show the proportions of flaky particles in selected sizes, and the results of tests to show how much coal is liberated from impurities by crushing the coarsest sizes. These data have been obtained in connection with an extensive study of coal-washing now being conducted by the U. S. Bureau of Mines and the University of Alabama, with U. cooperation of the different operators of Alabama. As the work progresses other reports will follow containing furtner data on the washability both of the Mary Lee seam and of other seams in Alabama and giving the results obtained in preparing these coals by various methods.Although a great amount of investigative work on the preparation of the Mary Lee scam was previously carried on by the various coal companies of the district, comparatively little of this information has been published. In governmental publications three references have been found. Forbes5 gives a number of sections with proximate and ultimate analyses of face samples taken in the mines. Gandrud and Britton'' show sections of this seam at Flat Creek and New Castle; they also give the specific gravity and ash contents of the partings of coal and impurities. In their paper Yancey and Fraser7 include washability studies and washing data from the Sayreton mine of the Republic Iron & Steel Co."

Jun 1, 1930

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1952 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 94 samples of aviation gasoline which include, for the first time in this series of reports, data on five samples of grade 108/135 aviation fuel. Data also are given for 34 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers? production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1953

By Harry W. Campbell

A mineral survey by Bureau of Mines personnel identified no mineral resources or mineral occurrences with development potential at prospects in the Mecca Hills Wilderness Study Area (WSA). Bentonite occurrences are in Skeleton Canyon and Surprise Canyon. Sand and gravel occurrences are numerous in and near the WSA. Much of the Mecca Hills WSA was leased for oil and gas exploration in 1983. No current mining claims or other leases were found in the study area. The Skeleton Canyon Clay Mine yielded clay to seal irrigation canals, Clay to seal ponds was also mined from the Red Top Clay Mine west of the USA. A sand and gravel pit south of the study area (near Box Canyon Wash) supplied material for local construction projects. A commercial sand and gravel pit was operating in 1983 near the mouth of Thermal Canyon 4 miles west of the WSA.

Jan 1, 1984

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980

By B. H. Eccleston

Experimental data were obtained from two medium-duty diesel engines derated to qualify for use in underground mines. Gaseous and particulate emissions from these engines were measured and results provide information on the effect of exhaust treatment devices on the emissions. The devices in the study were a catalyst, a particulate trap, and an exhaust gas cooler of the water scrubber type. Emission levels of carbon monoxide and hydrocarbons were observed to be very low in comparison with emission levels of comparable engines in full-rated operation. Oxides of nitrogen and benzo(a)pyrene content of the exhaust also were found to be somewhat low in comparison with previous findings. For particulate reduction, the combination of a particulate trap and a scrubber was observed to be the most effective combination tried; in some cases, over 60 pct particulate reduction was effected by the trap-scrubber combination.

Jan 1, 1981

By R. T. Sorensen

Bench-scale and continuous testing were performed to adapt the anionic process for flotation of calcium activated silica to the fine-grained hematitic-goethitic jaspers from the Marquette range, Michigan. These ores typically contain about 35 percent Fe and require grinding to about 80 to 100 percent minus 400 mesh to insure an adequate liberation of gangue from the iron oxides. A method for removal of troublesome slime fractions without excessive iron loss, by first dispersing the quartz and then selectively flocculating the iron oxides, was evolved in the laboratory and successfully accommodated to pilot plant practice. The efficiency of the flotation process was improved with respect to both reagent usage and concentrate grade and recovery by using the selective flocculation-desliming technique as a pretreatment. The benefits of the combined desliming-flotation procedure were most evident in pilot plant processing. The best tests on two ores yielded recoveries of about 84 percent in concentrates containing 65.1 percent Fe and 4.8 percent SiO2 and 66.2 percent Fe and 3.9 percent SiO2, respectively. These results are in comparison to recoveries about 10 percent lower than the above to concentrates containing 63.9 percent Fe and 6.6 percent SiO2 in the one instance, and 63.6 percent Fe and 7.2 percent SiO2 in the other, obtained by flotation without the prior desliming treatment.

Jan 1, 1967

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied a 12,564-acre portion of the 34,795-acre Rockhouse Wilderness Study Area (CA-010-029) in order to evaluate its identified mineral resources. The study area is located in Kern and Tulare Counties, CA, about 60 air mi northeast of Bakersfield at the south end of the Sierra Nevada. A review of the geologic and mining literature, and a field examination identified a turquoise and a gold prospect in the study area, and another gold prospect and a feldspar prospect within a mile of the study area boundary. Thirty-three rock and 16 alluvial samples were taken.

Jan 1, 1988

By H. V. Makar

An aluminizing dross which is accumulating as a waste material in substantial quantities was tested for possible use as a steel deoxidizer. This material, consisting mainly of aluminum, silicon, and iron, was used to deoxidize laboratory-scale melts ranging from 7 to 100 pounds. Oxygen analysis showed that the aluminizing dross was effective in reducing oxygen levels in steel. A direct comparison with aluminum wire showed the dross material to be at least as effective. Under similar test conditions with 7-pound melts, 3 grams of aluminum reduced the oxygen concentration from 210 to 175 ppm, while 4 grams of aluminizing dross (equivalent to approximately 2 grams aluminum) reduced the oxygen concentration from 250 to 170 ppm. An additional 4 grams of aluminizing dross produced a final oxygen concentration of 140 ppm.

Jan 1, 1972

By H. A. Doerner

For the past three or four years attention has been attracted to the deposits of lead vanadate in the Goodsprings , Nevada , district . Some ore running as high as 9 per cent 205 has been produced , but most of it runs from 0.5 to 3 per cent . Only a little ore , and that of the richer sort , has been shipped , since the low- grade ore will not stend the cost of shipment and no concentration mill has been available . Preliminary experiments indicate that chemical treatment of the low- grade ore without concentration is not feasible . Its treatment therefore involves two distinct problems ; first , mechanical concentration ; and second , a smelting or chemical treatment to obtain the lead and vanadium in marketable form . Upon this basis the work has been conducted . The writer wishes to acknowledge the excellent work done by J. T. Norton and Virgil Miller on table concentration and by J. E. Conley , who suggested and did preliminary work on the direct smelting method . Many helpful suggestions were received from Dr. S. C. Lind and John Gross of the Bureau of Mines . The ores were furnished by Mr. Frank Williams and Mr. James Ewing .

Jan 1, 1923

By David L. Veith

This report summarizes a Bureau of Mines review of selected literature on the effects of subsidence due to high-extraction underground coal mining on farmland areas. The data are presented for consideration in evaluating the subsidence effects due to similar mining techniques on the prime farmland areas of Illinois. In Illinois the ground water level in the glacial drift is only 2 to 15 ft below the nearly flat to gently rolling ground surface. The main subsidence concern is flooding, as caused by the lowering of the ground surface, and the subsequent effects on crop production. Positive drainage must be maintained in the farmlands, and the need exists for extensive regional planning by the mining and agricultural industries to maximize short- and long-term production from both efforts. The Bureau is cooperating with the State of Illinois to develop basic information necessary for such planning.

Jan 1, 1987

By Floyd G. Anderson

Owing to the rapid growth of the perlite industry in recent years, the Bureau of Mines has received numerous requests for information relative to the possible harmful effects of breathing dust resulting from the processing and use of perlite. As published information on the composition of perlite is rather meager, consisting chiefly of conventional chemical analyses, samples of crude and expanded perlite from 9 deposits in 6 Western States were studied. Crude perlite ores were examined petrographically and analyzed by chemical, spectrographic, and X-ray-diffraction methods. Sized crude and expanded perlites were analyzed chemically for total free and combined silica content.

Jan 1, 1956

By G. W. Jones

As a part of it investigations pertaining to the promotion of safety, the Bureau of Mines is investigating various means, useful for the elimination or mitigation of the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explocibility of many complex, gaseous, combustible atmospheres may be calculated in a simple manner without the necessity of performing laborious laboratory experiments. In a previous publication4/ data were given and a method described whereby the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen, could be determined by calculation. The information published in that report enables one to calculate the limits of inflammability of such gases as are liberated by mine fires, gases from explosives, automobile exhaust ran, uses present after mine explosions, blast-furnace gas, and other gases containing part of or all of the above-listed constituents.

Jan 1, 1938

By Ronald T. Mayerle

There are no producing or developing mines in the Rattlesnake RARE II area. Specific areas with mineral occurences are prospects for: 1) stratabound copper and silver in Belt sedimentary rocks on the northwest border of the study area; 2) base metal sulfides, in thin veins and shear zones in Belt sedimentary rock, and diabase dikes and adjacent metasedimentary rocks in the southern part of the study area; 3) barite in sedimentary rocks near Rattlesnake Creek and Sheep Mountain; 4) limestone near Rattlesnake Creek and Blue Point; and 5) silica in quartz veins near the headwaters of Rattlesnake Creek and Sanders Lake. Stone, sand and gravel suitable for construction material are in the study area; however, equal or better quality deposits are common throughout the region. The RARE II area has no known oil and gas, coal, or geothermal energy deposits.

Jan 1, 1983

By Robin B. McCulloch

No producing mines are in the study area. Sample results indicate the only resources in the study area are low grade phosphate deposits associated with Cuyama Phosphate Mine (fig. 1). Within the study area, are more than 21.4 million tons of inferred subeconomic phosphate rock resources which would be reserves at an 80 percent higher phosphoric acid price; weighted average grade is 4.84 percent phosphorous pentoxide (P205). About 17.6 million tons of similar grade are outside the area to the northwest. The South Cuyama Oil Field, adjacent to the study area (fig. 1), produces petroleum from the Vaqueros Formation which underlies parts of the study area. Oil and gas potential was evaluated by U.S. Geological Survey. INTRODUCTION Location, Size, and Geographic Setting The U.S. Bureau of Mines conducted a mineral survey of the Fox Mountain RARE II area (No. 5120) during the summer of 1981. The area was examined to determine the presence or absence of mineral resources and reserves, and to estimate tonnage and grade where possible.

Jan 1, 1982

By L. M. Demers, D. C. Kuhn

The alveolar macrophage (AM) responds to stimuli such as coal mine dust by releasing inflammatory mediators such as cytokines, growth factors. reactive oxygen species. and eicosanoids. Eicosanoids are synthesized by°AM through the action of cyclooxygenase and lipoxygenase enzymes and serve to modulate the proinflammatory function of this cell as part of the lungs' host defense mechanism. Reactive oxygen species can be generated by AM as a by-product in the biosynthetic pathway of the prostaglandins. AM produces primarily prostaglandin E2, thromboxane A2, and leukotriene B4 as part of the cellular response to an inflammatory stimulus. There is evidence to suggest that eicosanoid production by AM is functionally linked to both surface interaction with mine dust particles like silica and by the phagocytosis of the dust particle itself. In this report, we examined the effects of an antioxidant, vitamin E. on dust-induced synthesis of PGE2 and TXB2 in vitro and in vivo by AM obtained by bronchoalveolar lavage from rats. We also looked at the effects of the surface of silica particles on AM eicosanoid biosynthesis under conditions of calcination, a process that removes exposed hydroxyl groups from the surface of silica particles, thus reducing the likelihood of soluble hydroxyl radical formation. Treatment of AM with vitamin E in vivo and in vitro reduced the augmentation in eicosanoid production usually observed when AM are exposed to mine dusts. These results suggest that vitamin E may effectively reduce the inflammatory and fibrotic response produced by inhalation of mineral dust through an antioxidant mechanism. Silica that has been chemically altered by calcination was unable to activate AM eicosanoid production in vitro when compared to untreated, freshly fractured silica. These findings suggest that the mechanism by which dust particles can activate AM eicosanoid release may involve interaction of surface and/or soluble factors with the cell membrane. Taken together, these studies point to the involvement of AM eicosanoid production as part of the proinflammatory response of this cell to occupational inhalation of mineral dust. - Environ Health Perspect 102(Suppl 10):97-100 (1994)

Dec 1, 1995

By Wesley T. Holmes II, Lloyd H. Banning

Electric - smelting studies were made on titaniferous materials obtained from the Klukwan and Snettisham , Alaska ; Choteau , Mont .; and Iron Mountain , Wyo . , deposits with the objective of determining the feasibility of producing pig iron and an enriched titania slag in one test series and pig iron alone in another test series . In addition , related studies were conducted to determine the amenability of Choteau crude ore to wet -magnetic separation and to determine the quality of steel that could be produced from the titaniferous pig iron . The continuous smelting tests were made in a three - phase , submerged - arc , electric furnace , and the laboratory steelmaking tests were made in a singlephase electric - arc furnace . A continuous , belt - type , wet - magnetic separator was used in conjunction with a ball mill and a spiral classifier in recovering titaniferous magnetite from the crude Choteau ore . Pig irons containing less than 0.05 percent phosphorus or sulfur were readily produced from the titaniferous materials ; iron recoveries ranged from 92 to 98 percent . The Choteau ore was ground to minus 65 - mesh to produce a concentrate containing 60 percent or more iron . The steel produced from the titaniferous pig iron was a high - quality product .

Jan 1, 1964

By J. T. Dunham

The Bureau of Mines studied by dilatometry the effect of titanium on the thermal expansivity of hot-rolled zinc and Zn-l percent Cu alloy. The titanium content of the alloys was varied up to 0.3 percent. Expansion coefficients were determined from measurements made both parallel and perpendicular to the plane of the rolled sheet. Titanium reduced expansion parallel to the plane of the sheet, especially in the rolling direction, but increased expansion perpendicular to the sheet. Basal-plane pole figures showed that the degree of preferred orientation increased with the titanium content in the alloy, and that anisotropic expansion can be correlated to sheet texture.

Jan 1, 1965