Search Documents

By Paul Hatmaker

Pumice and pumicite are siliceous volcanic substances quite similar in chemical composition , but somewhat different in physical properties , manner of formation , and mode of occurrence . Production in the United States has increased from 23,271 tons valued at $ 94,943 in 1910 , to 56,843 tons valued at $336,099 in 1930. Both pumice and pumicite are included in these figures as it has been impractical to collect statistical data on the separate commodities .

Mar 1, 1932

By James M. Stuckey

In a search for improved methods of upgrading tar obtained by low-temperature carbonization of coal, monoethanolamine (MEA) was found to be effective in extracting tar acids from coal tar distillates derived from a subbitunwous and a lignite coal. Patch extractions showed that both yield and purity of the extracted acids improved with increasing volume ratios of monoethanolamine to tar acid, varied from 1:4 to 8:1. Yield improved, but purity decreased as the concentration of monoethanolamine was changed from 30 to 70 volume-percent, and as the concentration of tar acid in distillate was increased ad from 14 to 45 percent. In a continuous countercurrent extraction employing a double solvent (monoethanolamine and hexane) approximately 80 percent of the tar acids was extracted from 170° to 350° C. tar distillate when using 1.6:1 volume ratios of amine:tar acids. Tar acids isolated from his extract, although of improved purity, contained appreciable quantities of neutral oils and some tar bases. Aqueous monoethanolamine was not effective for extracting the last 10 to 15 percent of tar acids in 170° to 350° C. distillate oil from lignite coal. The highest yield of isolated tar acids and the best recovery of monoethanolamine were obtained by diluting the extract with water and saturating with C02. Some losses of solvent were encountered when aqueous monoethanolamine solutions were heated through decomposition of the amine with the liberation of ammonia.

Jan 1, 1960

By G. Schuman

Variations in pyrite reactivity are known to exist within samples collected from different areas. Using samples collected from acid and non-acid sites, the relationship between the factors affecting pyrite oxidation and observed variations in pyrite reactivity was studied. Heavy liquid separations were used to extract the pyrite from nine pulverized rock, coal, and coal refuse samples. Simulated weathering tests were used to determine the degree of reactivity of the extracted pyritic material. Representative portions of each pyritic sample were analyzed for whole rock composition (including pyritic sulfur and neutralization potential), for elemental composition, and by x-ray diffractometry. The samples were also examined with reflected light microscopy to ascertain pyrite morphology distributions. Tests for the presence of iron-oxidizing bacteria were all negative indicating the leaching tests were conducted under abiotic conditions. The results of the simulated weathering tests permitted the partitioning of the samples into two groups based on positive or negative neutralization potential (NP) values. Determinations were then made to evaluate the degree to which a variety of factors, including temperature, partial pressure of oxygen and water, and crystallography affected pyrite reactivity. Multiple regression analyses showed no statistically significant relationship between degree of reactivity and elemental composition. However, for samples with negative NPs, a simple regression analysis showed a strong linear relationship to exist between the reactivity of the pyrite and the proportion of "unstable" pyrite (framboidal + mossy pitted) found in each extracted pyrite sample. Samples of pyrite with positive NPs, although producing acidity, did so in at least one order of magnitude less than the NP deficient samples, indicating the important role that NP plays in controlling pyrite reactivity. A simple linear regression between cumulative sulfate production and NP for the three samples with positive NPs had a correlation coefficient of 0.99. For the nine samples grouped together, a linear regression model between cumulative sulfate production and NP (both negative and positive) was established between log of sulfate and NP.

Jan 1, 1991

By George L. Gates

The Bureau of Mines studied pressure-buildup data from a number of California gas wells to determine if the reservoir properties calculated from these data correlated with field-observed reservoir properties. Pressure-buildup curves from 24 wells showed distinct changes in slope, indicating changes in permeability of the reservoir rock. Calculated distances from the wells to indicated permeability changes were in fair agreement with distances deter-mined in the field. Pressure-buildup curves from three wells had more than one distinct change in slope, indicating multiple permeability changes. Thus field data supported the theoretical relations used to calculate reservoir properties from pressure-time relations measured in gas wells.

Jan 1, 1967

By N. S. Dalal, A. H. Hoffman, X. Shi, D. E. Banks, J. K. H. Ma, Y. Rojanasakul

Excessive production of reactive oxygen radicals by alveolar macrophages is proposed to play an important role in oxidative lung injury. A major product of oxygen radical formation is the highly reactive hydroxyl radical (•OH) generated via a biologic Fenton reaction. In addition to its known ability to induce lipid peroxidation, recent studies have suggested that the •OH may exert its cytotoxic effect through the alteration of [Ca2+], homeostasis. To test this potential mechanism as well as to investigate the relationship between •OH and Ca" overloading in cytotoxic injury, isolated rat alveolar macrophages were exposed to externally generated radical system, H2O2 (0.01 to 1 mM) and Fe (1 mM) and their [Ca2+] levels and cell injury were monitored using quantitative fluorescence microscopy with the aid of the specific Ca" indicator, Fura-2, and membrane integrity indicator, propidium iodide. Electron spin resonance measurements using the spin trap 5,5-dimethyl-1-pyrroline-N-oxide (DMPO) confirmed the production of the .OH radical by this system. Upon the addition of the radicals, the macrophages displayed a rapid initial rise in [Ca2+] which was followed by a slower but more pronounced [Ca2+], elevation that reached a level 3 to 5 times higher than the basal level. This process preceded cell death as evident by nuclear propidium iodide fluorescence. Depletion of extracellular Ca" inhibited both the [Ca2+], response and cell injury. Preincubation of the cells with the Ca" channel blocker verapamil or .0H radical scavenger mannitol similarly inhibited the [Ca2+], rise and loss of viability. Firefly luciferase assay of cellular ATP content demonstrated that the alterations in [Ca2+], following .0H treatment preceded the depletion of ATP. Changes in membrane potential caused by Na* substitution with K* had no significant effect on either the unstimulated or stimulated [Ca"], levels. Taken together, these measurements indicate that .OH-induced injury in alveolar macrophages is associated with the alteration in [Ca2+], homeostasis. The mechanism of •OH-induced [Ca2+] loading is not due to nonspecific membrane damage or energy depletion, but mainly due to an increase in Ca2+ influx through Ca2+ selective channels. This Ca2+ over-load state as well as energy depletion caused by the oxidant may activate certain cellular degradative processes leading to cell injury and death.

Nov 1, 1995

By Z. Zhiqun, V. A. Marple, B. Y. H. Liu

"IntroductionIt is commonly understood that aerosol particles may be injurious to human health if they are of a size that enables them to enter the respiratory tract. Coal Workers' Pneumoconiosis (CWP) is one disease known to be caused by coal mining related particles.The location in the respiratory tract where the particles are deposited is primarily a function of the equivalent aerodynamic diameter (EAD) of the particle. The equivalent aerodynamic diameter is the diameter of a spherical particle with a density of 1.0 gm/cm3 with the same falling speed as the particle in question. For a spherical particle the calculation is rather simple in that the equivalent aerodynamic diameter is simply the diameter of the particle in question multiplied by the square root of the density of the particle. For irregularly shaped particles, such as coal particles, there is no simple way to make the EAD calculation. For example, Figure 1 is only one of an infinite variety of particle shapes that can be found in practice and the aerodynamic size of this particle and, therefore, its deposition location in the respiratory tract would be nearly impos-sible to estimate accurately.The normal method for determining the aerodynamic diameter of particles has been to experimentally measure the size of the particles in a settling chamber or with an inertial classifier such as an impactor, cyclone or a centrifuge, since inertial classifiers have the property of classifying the particles according to their aerodynamic diameters."") However, these devices can only give limited information on the EAD of a single particle with a specific shape. Impactors and cyclones, for example, collect particles in size ranges and not at a specific size, so the determination of the EAD of a specific particle is not possible. A centrifuge, on the other hand, can measure the EAD of a specific particle but the equipment is costly and procedure laborious, and it may not be possible to disperse a particle of a specific shape into the centrifuge. The centrifuge can be used to determine the EAD of clusters of spheres in various arrays, but introducing particles of a specific irregular shape may not be feasible. Furthermore, the EAD is a function of the orientation of an irregularly shaped particle and the orientation of a particle in an inertial classifier is unknown. The orientation may also vary as the particle passes through the classifier.Because of the difficulty in determining the EAD of an irregularly shaped particle, we have undertaken a program to apply theoretical numerical methods to calculate the EAD of any shape particle. In our laboratory we have, for some time, been using numerical methods to determine the flow field of air within instruments such as impactors, (2) inlets, (3) and virtual impactors (4) Recently, this technique has been expanded into the three-dimensional regime, and the flow fields and particle motion characteristics within cyclones (5) and glove boxes have been studied. We have now begun to use these numerical three-dimensional flow programs to study the flow field around irregularly shaped particles to determine their drag coefficients, falling speed, and thus, their EAD."

Mar 1, 1989

By Arden D. Fugate

This work was conducted to determine a feasible process for converting siliceous fluoride offgases to a commercially usable product. The offgases were generated by pyrohydrolytic defluorination of low-grade fluorspar in a gas-fired rotary kiln, and fluorine was collected as a hydrofluoric-fluosilicic acid. A silicon-free fluoride solution for further processing was then produced by neutralizing the acidic scrubber solution with anhydrous ammonia, silicon being separated as orthosilicic acid. Ninety to ninety-nine percent of the fluorine originally present remained in solution as ammonium fluoride. Silicon was also separated from synthetic fluosilicic acids, having F-to-Si weight ratios ranging from 3.50 to 14.3. The solutions below a ratio of 4.06, the F-to-Si ratio of H2SiF6, containing dissolved silicon were desiliconized as completely as those containing less than the stoichiometric quantity of silicon. An electrolytic-grade cryolite was recovered from the ammonium fluoride solution by reacting with either sodium aluminate or alumina trihydrate and sodium hydroxide. A product containing 97 to 100 percent of the fluorine, represented by Na3A1F6, was recovered, and 94 to 99 percent of the theoretical yield was realized.

Jan 1, 1963

By D. J. Bauer

A primary amine extraction system was investigated for fractionating a cerium-group, lanthanide sulfate mixture. Addition of diethylenetriaminepenta-acetic acid (DTPA) to the amine extraction system resulted in separation factors as high as 5.4 for lanthanum-cerium, 8.0 for cerium-praseodymium, 3.7 for praseodymium-neodymium, and 7.0 for neodymium-samarium. In multistage studies on a cerium-free lanthanide mixture, 96 percent of the lanthanum was recovered with a purity of 95 percent.

Jan 1, 1968

By A. E. Harak

To determine the retorting characteristics of a column of mine-run, ungraded oil shale ranging in size from fines to pieces weighing as much as 5 tons, a 150-ton batch retort was designed and constructed at the Laramie Energy Research Center, Laramie, Wyo. The retort vessel is 45 feet high by 11-1/2 feel in inside diameter and is supported in a 92-Foot-high steel superstructure. Mine-run shale from the Bureau of Mines facility near Rifle, Colo., assaying about 25 gallons of oil per ton, is currently being used as the test shale. To date, three runs have been completed. Results of the second and third runs are reported in this paper. The two runs considered in this report are the first of a series of nine to determine operating conditions that will yield maximum oil recovery from a column of mine-run shale. Variables studied :ire the oxygen content of the retorting gas and the space velocity of the retorting gas expressed as ft3 gas/ft3 bed/min. Oil recoveries for the two runs reported are 62.2 volume percent of Fischer assay for the run using higher oxygen and space velocity, compared with 39.3 volume-percent when less oxygen and a Lower space velocity were used.

Jan 1, 1971

By Gary P. Sames

This U.S. Bureau of Mines study was conducted in eastern Kentucky drift mines as part of an ongoing research program to characterize the outcrop barrier zone. "Hillseams" were identified as the dominant geologic cause of roof instability unique to the outcrop barrier zone, with many roof fall injuries and fatalities attributed to them. Hillseam is the eastern Kentucky miners term for weather-enlarged tension joints that occur in shallow mine overburden where surface slopes are steep. Hillseams are most conspicuous within 200 ft laterally of a coalbed outcrop and under 300 ft or less of overburden. Hillseams form by stress relief, and therefore tend to parallel topographic contours and ridges. They can intersect at various angles, especially under the nose of a ridge, and create massive blocks or wedges of roof prone to failure. Examples of hillseams are described in both outcrop and in coal mine roof to establish their geologic character and contribution to roof failure.

Jan 1, 1989

By E. G. King

THIRD-LAW entropy data for zirconium-containing compounds are sparse. Kelley a lists entropies at 298° K. for the oxide, tetrachloride, nitride, and silicate, as well as for the metal. The present paper presents heat capacities between 51° and 298° K. and entropies at 298.15° K. for the zirconates of the alkaline-earth metals-calcium, strontium, and barium. The authors believe magnesium zirconate does not exist as a stable compound at room temperature. Entropies of formation from the constituent oxides also are given. MATERIALS The materials used in this investigation were synthesized and analyzed in the Berkeley Laboratory of the Bureau of Mines. Calcium zirconate was prepared by heating an intimate mixture of reagent-grade calcium carbonate and pure zirconia for 30 hours between 1,200° and 1,300° C. and for 32 hours between 1,400° and 1,500° C. As part of the heating schedule, the sample was ground and mixed seven times. Periodic analyses and minor adjustments of composition were made. Analysis of the final product gave 31.19 percent calcium oxide (theoretically 31.28 percent) and 68.67 percent zirconia (theoretically 68.72 percent). The X-ray diffraction pattern agreed with that in the ASTM catalog.

Jan 1, 1960

By Charles W. Huggins

To determine the nahcolite and dawsonite content in oil shales, the Bureau of Mines compared X-ray diffraction, infrared spectroscopy, thermal methods, and a previously published method by Smith and Young based on the selective solubility of sodium compounds. The Smith and Young method and a new method based on the weight of carbon dioxide produced by thermal decomposition are recommended for determining nahcolite. X-ray diffraction and the Smith and Young method are recommended for determining dawsonite. X-ray diffraction, infrared spectroscopy, and differential thermal analysis were useful for identifying other minerals in the samples.

Jan 1, 1973

By A. U. Miller

For many years Illinois has been one of the leading coal producers in the United States and as such its safety record has compared very well with the other large coal producing States , both in tons produced and millions of man -hours of exposure per fatal accident . ( See Table 25 in Bureau of Mines Bulletin 293. ) During the 10-year period from 1917 to 1926 , inclusive , the average production in the United States per fatal accident was 278 , 109 tons . The aver age for the State of Illinois for the same period was 409,249 tons . Illinois produced 450,464 tons per fatal accident, and in 1928 produced 390,630, tons , or an average of 419,721 tons for the 12- year period from 1917 to 1928 , inclusive . In 1927 During the year 1929 , the shipping mines of the State made a decided improvement in their record over any previous year . Table 1 shows the monthly production and the tons produced per fatal accident . During 1928 and 1929 safety work was actively carried on in Illinois . Safety meetings were held with mine officials , representatives of the State. De partment of Mines , and the United States Bureau of Mines . At these meetings mine hazards and accidents were discussed and remedies suggested for : their elimination in the future . It is believed that first - aid training was to a considerable extent instrumental in reducing accidents and in making the good safety records in Illinois during 1928 and 1929. During these years ( as well as in 1926 and 1927 to a somewhat less extont ) en intensive rirst-aid training campaign was con ducted in Illinois by the officials and members of the United Mine Workers of America , coal companies, State Department of Mines and Minerals , and the U. S. Bureau of Mines , Every first -aid class was made a safety meeting ; where accidents and general safety were discussed freely while teaching first aid. During this time , anproximately 25,000 persons were trained in first aid, and 17 coal companies were issued certificates for having 100 per cent of their employees. trained in first aid. Since January 1 , 1926 , more than 40,000 have received first -aid training in and around Illinois mines , and including those who received training previous to this date , it is believed that at least 90 per cent of the miners in Illinois have received first -aid training . This state ment is based on the fact that the labor turnover in Illinois is not large .

Apr 1, 1931

By J. S. Kennedy, R. G. Omeara

Beryllium is a strategic metal of ever-increasing peacetime importance because of the unusual properties of beryllium-copper alloys. These unusual characteristics are the combination of high strength and hardness, high fatigue resistance, and high wear resistance in alloys that have the corrosion resistance of copper. The principal industrial source of beryllium is the mineral beryl, a beryllium-aluminum silicate that occurs in pegmatites associated with quartz, feldspar, mica, and smaller amounts of various accessory minerals. The beryl is usually recovered in processing the pegmatites for the recovery of some of the other mineral constituents. Pegmatite deposits are found in various parts of the United States, but those in the Black Hills of South Dakota are the source of most of domestic production. The beryl marketed from the South Dakota pegmatite deposits occurs as coarse crystals, which are obtained by hand sorting. These pegmatites also contain other valuable minerals.

Jan 1, 1948

By Harold J. Rose

The economic situation in Switzerland during recent years has resulted in theoretical studies , engineering development work , and many commercial installations of ingenious methods for using energy more efficiently . The purpose of the present investigation was to learn of recent Swiss developments for the more effective use of coal , which comprises 98.9 percent of the romaining known mineral - fuel reserves of the United States .

Jun 1, 1947

By Christopher Mark

Roof bolt system design means the selection of the type, length, capacity, and pattern of bolts for a particular application. Despite research efforts dating back 50 years, no design methodology has found wide acceptance. This paper begins by identifying four mechanisms that roof bolts use to reinforce the ground. It argues that the reinforcement mechanism is determined by the roof geology and stress level, not by the type of bolt. Next, the attributes of roof bolts are discussed in the light of recent research, including anchorage mechanism, installed tension, length, capacity, timing of installation, and installation quality. Several significant areas of controversy are identified. Design methods from around the world are discussed, including those based on empirical research, numerical modeling, and roof monitoring. Finally, some simple guidelines for preliminary design of roof bolt systems are proposed based on statistical analysis of roof support performance at 37 U.S. mines.

Jan 10, 2000

By E. C. Perkins, R. S. Lang, D. M. Taylor, H. Dolezal

The amenability of titaniferous slags and domestic mineral concentrates to chlorination was determined in a 6 - inch diameter fluidized bed chlorinator . Ilmenites from Valley County , Idaho ; Aiken , S.C ,; Trail Ridge , Fla .; and MacIntyre , N.Y .; and a titaniferous magnetite from Iron Mountain , Wyo . , were used in preparing the slags . The domestic minerals tested were an ilmenite concentrate from Valley County , Idaho , and a rutile concentrate from Magnet Cove , Ark . A high - grade Australian rutile was used as a standard for comparison . The impurity content of the slags and minerals tested , which was the most critical factor affecting their performance , was dependent on the geographical source of the material . All of the materials tested were amenable to chlorination in a fluidized bed although some required special operating conditions . Titanium extractions and chlorine utilization were over 90 percent for most of the slags and the Australian rutile . The Valley County , Idaho , ilmenite performed well in the reactor despite its 34 percent iron content .

Jan 1, 1963

By F. S. Kendorski

This report covers the work on developing criteria for determining when a hazard exists when mining stratified mineral deposits beneath bodies of surface water. The nature of water bodies is considered, the disturbance to the strata induced by mining is described, inundation case histories reviewed, reasonable water inflows derived, and methods of mining to prevent or minimize the hazard are presented. Criteria are given whereby effected industries and agencies can recognize a potential hazard and plan a mine accordingly, releasing considerable mineral reserves otherwise considered unminable.

Jan 1, 1979

By Sidney Katell

This Bureau of Mines study estimates typical capital investments, operating costs, and selling prices for two bituminous coal strip mines in the Eastern and Interior provinces and a subbituminous coal operation in the Northern Great Plains province. The annual productions were based on tonnage required to fuel a 250-MM-scfd, high-Btu gas plant. The annual tonnage for the Eastern province mine is 4.8 million tons; for the Interior province mine, 6.72 mi 11 ion tons; and for the Northern Great Plains province mine, 9.2 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of May 12, 1974, under the terms of the Bituminous Wage Agreement of 1971, and costs for material and equipment are based on 1973 and early 1974 indexes . Initial capital investment varies: $45,358,600 for the 4.8-million- ton-per-year (MM tpy) mine in the Eastern province, $54,603,000 for the 6.72 MM tpy mine in the Interior province, and $29,871,000 for the 9.2 MM tpy mine in the Northern Great Plains province. Total capital invest-ments for the Eastern province mine, the Interior province mine, and the Northern Great Plains province mine are $61,070,000, $76,753,000, and $56,286,000, respectively. Corresponding selling prices for the coal, per ton, are $4.79, $4.23, and $2.66, assuming a 12-percent discounted cash flow rate of return after Federal income taxes. These studies are considered typical for the areas involved. Costs will vary depending on specific locations in these areas.

Jan 1, 1974

By D. J. Bauer

The Bureau of Mines demonstrated the feasibility of fractionating lanthanide nitrates with a tertiary amine on lanthanum-cerium and thulium-ytterbium pairs. Optimum values were determined for pH, phase concentration, and percent chelation of metal ions in the aqueous phase. Percent extraction is markedly dependent on the concentration of lithium nitrate in the aqueous phase. Selective masking of the heavier element in each extraction system with DTPA or EDTA aqueous-phase chelating agents resulted in lanthanum-cerium separation factors of 8.5 and thulium-ytterbium separation factors of 3.4.

Jan 1, 1966