Search Documents

By K. L. Rubow

"IntroductionAir sampling for airborne contaminants requires a system for moving air, a collection method, and a procedure to determine the quantity of contaminant collected. Because occupational exposure limits and air quality standards frequently are expressed in terms of concentrations, a method of determining the volume of air sampled is also needed. The four principal components in a sampling train are shown in Figure 12-1. The inlet admits the air sample into the train; the collector(s) separates the gas, vapor, or particles from the air; the flowmeter measures the rate or total quantity of air sampled; and the pump (air mover) provides the suction required to draw an air sample through the train. Inlet sampling considerations are discussed in Chapter 21. Various types of collectors are described in subsequent chapters. Flowmeters are discussed in Chapter 7.This chapter will describe the air mover portion of the sampling train and air sampling systems that contain three or four components in a convenient package. The chapter consists of two parts. The first part contains a brief description of the different types of air movers and air sampling systems. The second part consists of tables and figures showing detailed information on a wide variety of commercially available air movers and sampling systems. ient size is filled with a liquid in which the suspected contaminant is insoluble. When the liquid is allowed to escape from the vessel, it is replaced by air from the atmosphere to be sampled. Such an air sample is an integrated sample rather than an instantaneous sample because the mass of fluid requires a finite time to empty. In fact, by employing a large vessel with controlled drainage, this method can be used to move air at low flow rates through a sample collector for extended intervals. Additional discussion of this method can be found in Chapter 17."

Dec 1, 1996

By C. N. Adams

The purpose of this investigation was to evaluate the physical and mechanical properties of high-purity titanium made by two processes. Sodium-reduced metal with 58 Brinell hardness number (B.h.n.) and electrorefined metal with 60 B.h.n. and 70 B.h.n. were used. Titanium of these hardness levels did not work-harden excessively, and beyond 40 percent cold work the hardening effect was not great. Rapid softening occurred when the metal was annealed at temperature between 300° and 600° C. Full annealing, as determined by property and microstructure studies, was accomplished after 30 minutes at 700° C. A recrystallization diagram is presented which is based on determinations of annealed grain size as a function of rolling reduction and annealing time. For reductions of less than 20 percent, exaggerated grain growth occurred during annealing; for reductions greater than 20 percent, the variation in grain size for each annealing temperature was minor.

Jan 1, 1961

By Eugene Frey

"INTRODUCTION The Good Fortune mine was sampled by an engineer of the Bureau of Mines in June 1944. Project 984 was set up under the strategic minerals program to make old workings accessible for this sampling program. Actual operations commenced June 1, 1944, and were completed June 30, 1944.The deposit was visited and discussed briefly by Sidney H. Ball 3/ of the Federal Geological Survey in the summer of 1906 and by H. M. Chance 4/ several times from 1887 to 1900.LOCATION AND ACCESSIBILITYThe Good Fortune mine is situated in the Hartville mining district in Platte County, Wyo., approximately 9 miles northwest of the town of Guernsey. The property is about 100 miles north of Cheyenne, Wyo. (fig. 1).ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metal¬lurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests."

Aug 1, 1947

By J. A. Stampe

In connection with its investigations of strategic minerals in the United States, the Bureau of Mines ran magnetic surveys totaling more than 533,000 linear feet at 30 deposits of magnetite in northern New Jersey. These deposits occur in a belt of granitic gneiss and in limited areas of limestone. The ore consists of magnetite accompanied by score of the following minerals: Hornblende, augite, apatite, feldspar, biotite, calcite, garnet and pyrolusite. Results of these investigations are being presented in two reports of which this is the second. The first paper, Certain. Magnetite Deposits in New Jersey, by A. L. Neumann and McHenry Mosier, was issued in April 1948 as Report of Investigations 4225.

Jan 1, 1949

By Lucia Kuizon

The Antimony RARE II area is underlain principally by Mesozoic igneous rocks associated with the Sierra Nevada batholith. The San Andreas fault zone is near the southern boundary. Metallic mineral deposits are associated with the fault zone. These deposits were formed from magmatic solutions, and tend to be along shears and fractures within the country rock. Marble and dolomitic marble deposits occur in Paleozoic roof pendants or inclusions in the Mesozoic intrusive rocks in the area (Troxel and Morton, 1962, p. 52).

Jan 1, 1982

By BUREAU OF MINES

This summary of State laws on explosives was compiled primarily to ascertain what subjects relating to their control have been acted upon by each State legislature and , in general , how they have been treated . It does not include any legislation passed after 1942 , or any proclamations , regulations , or administrative orders . It does not purport or attempt to be authoritative . If any problem arises involving interpretation of the statutes of any particular State , the original source must be consulted for the exact words used by the legislature . This summary , however , will be useful in determining whether relevant statutes exist , and in locating thern quickly, with a minimum of effort . It will be of value also in comparing statutes in one State with similar statutes in other States to determine what construction has been placed upon them by the courts of these jurisdictions or to contrast the varying provisions of many States upon a similar subject . To make these comparisons easier , the statutory provisions for each State have been grouped under several major topics in outline form . Although this sometimes has resulted in disruption of the continuity of individual acts , the increased general clarity and availability of comparable sections have more than justified the procedure followed ,

Jul 1, 1943

By William O. Vanderburg

Some mines after passing through the prospecting stage and becoming sizable enterprises still adhere to the development program of the prospect, extending their workings without definite plans. In mining operations where definite structural conditions do not exist, a prearranged layout of mine development is not feasible; but where exploration and preliminary development have indicated the extent and probable limits within which the ore is expected, careful planning of development will result in a lowering of mining costs and a consequent increase is profits. A lack of definite plane for laying out mine workings is one of the contributory factors to unnecessarily high costs. Although this paper deals primarily with the influence of level spacing on mining costs, still other phases of mine development, such as the proper spacing of ore chutes and raises, can be analyzed on a cost basis in a similar manner, as shown herein. LEVEL SPACING The problem of establishing a new level or levels in order to exploit steeply dioping ore deposits and prospect the ground at depth recurs at intervals during the active life of mines. Driving levels is largely "dead work" and therefore costly. By the judicious selection of the proper level interval after balancing the opposing factors involved in the problem, a considerable saving in mining costs can be effected. Although much has been written in regard to the various methods employed in ore extraction, mining literature is still incomplete in regard to the factors-influencing level spacing at various mines. Level spacing involves procedures not lending themselves readily to description, and, moreover, it is a phase of mining operations that is apt to escape criticism, because only those in close contact with the operations are equipped with the necessary familiarity with the conditions to pass judgment.

Jan 1, 1932

By Dean H. Ambrose

Using three-dimensional (3-0) graphics computing to evaluate new technologies for computer-assisted mining systems illustrates how these visual techniques can redefine the way researchers look at raw scientific data. The U.S. Bureau of Mines is using 3-D graphics computing to obtain cheaply, easily, and quickly information about the operation and design of current and proposed mechanical coal and metal-nonmetal mining systems. Bureau engineers developed a graphics simulator for a continuous miner that enables a realistic test for experimental software that controls the functions of a machine. Some of the specific simulated functions of the continuous miner are machine motion, appendage motion, machine position, and machine sensors. The simulator uses data files generated in the laboratory or mine using a computer-assisted mining machine. The data file contains information from a laser-based guidance system and a data acquisition system that records all control commands given to a computer-assisted mining machine. This report documents the first phase in developing the simulator and discusses simulator requirements, features of the initial simulator, and several examples of its application. During this endeavor, Bureau engineers discovered and appreciated the simulator's potential to assist their investigations of machine controls and navigation systems.

Jan 1, 1992

By A. F. Colombo

The western Mesabi range nonmagnetic taconites containing about 34 percent Fe were evaluated by the Bureau of Mines in a 900-pound-per-hour pilot plant employing a selective flocculation-desliming-cationic flotation technique. The flotation step was a reverse flotation process and involved the flotation of the gangue minerals. The objective of the research was to increase the availability of domestic raw materials for the iron and steel industry. The beneficiated ores yielded concentrates containing 62 to 64 percent Fe and less than 5.5 percent Si02 with accompanying iron recoveries that averaged about 75 percent. Comparable flotation results were obtained with either fresh or 80 to 90 percent reclaimed water. Recycled waters having turbidities as high as 5,000 ppm Si02 did not affect the flotation process. Reclaimed waters containing residual calcium contents of less than 10 ppm gave better flotation concentrates than those containing 15 ppm.

Jan 1, 1976

By Victor Kalcevic

A gas-flow retort for thermal processing of oil shale to recover shale oil was developed by the Bureau of Mines at its Oil-Shale Demonstration Plant, Rifle, Colo., from 1948 to 1952. The retort is a crossflow gas-to-broken-solids heat exchanger. The heating medium is the gas produced in the shale retorting process. The gas is heated in specially designed stoves outside the retort and recycled to the retort. Oil shale from the Mahogany ledge section of the Green River formation in northwestern Colorado was the material processed. Indicated maximum oil recoveries for 20-to 25-gallon-per-ton shale in a l2-inch-thick shale bed and a 20-inch bed are 96 and 91 weight-percent of Fischer assay, respectively. Heat requirements for maximum recovery are 600 to 750 B.t.u. per pound of shale. Properties of the recovered shale oil are affected slightly by shale-bed thickness and extent of retorting. Oil recovery from oil shales assaying over 30 gallons per ton is lower than that from leaner shales.

Jan 1, 1959

By Edward D. Thimons

This Bureau of Mines report presents expected levels of air pollutants in the face areas of oil shale mines, based upon data collected by the authors and previous investigators. Ventilation requirements to maintain these pollutant levels below their threshold limit values and Federal and local mine air quality standards are discussed. Two practical face ventilation systems are discussed in terms of actual in-mine test experience.

Jan 1, 1986

By M. R. Geer

American and European practices in cleaning fine coal are strikingly different. The tables, launders, classifiers, and pneumatic devices used in America are seldom employed in Continental Europe, where much of the fine coal is cleaned in feldspar jigs, often supplemented by froth flotation of the extreme fines. This difference in choice of cleaning equipment may be fortuitous, but in large measure can be attributed to a difference in economic factors. Coal being more costly in Europe, there is greater emphasis on efficient cleaning of all sizes, including the extreme fines, and it is common to produce a high-ash middling for "on-site" consumption to avoid any waste of fuel value. The feldspar jig has been found advantageous under these conditions. In the United States fuel coal must be prepared as cheaply as possible, and metallurgical coal must be prepared as efficiently as possible; thus in both branches of preparation practice, any cleaning device that promises greater economy or higher efficiency warrants consideration. The feldspar jig, as employed in Europe, has a much higher unit capacity than the wet table used so extensively here and therefore offers economy in the capital costs of a washery through saving in space. As pointed out by Vissac,4/ the jig operates under automatic control, and therefore can cope with fluctuations in quality of feed. Maintenance costs for a single, large-capacity unit, such as the feldspar jig, would be expected to be lower than those for a battery of low-capacity cleaners. These considerations led the Bureau of Mines to undertake an investigation of the feldspar jig to determine its possible usefulness in this country.

Jan 1, 1958

Prevention of coal-mine explosions depends largely upon thorough knowledge of the causes that initiate explosions. A review of coal-mine explosions in one geographical area when supplemented by nationwide data of similar nature, should serve as a guide for the adoption of measures for explosion prevention. Explosions in bituminous-coal mines of the United States during the 10 years ended December 31, 1932, ranked third in the causes of fatal accidents and constituted 16.1 percent of all fatal accidents in bituminous mines. Kentucky now ranks fourth in coal output in the coal-producing States of this country; a study of the coal-mine explosions in this state will be of definite interest locally among coal-mining people, as well as to those in the coal-mining industry who are concerned in preventing coal-mine explosions. This circular reviews gas and dust explosions in Kentucky coal mines to show their hazards, to point out the influence of certain factors in causing explosions, and to indicate the effectiveness of preventive measures.

Jan 1, 1934

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high- temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols4 it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range.

Jan 1, 1932

By J. Douglas Causey

In 1986 and 1987, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied 73,010 acres of the 76,480-acre Lower Owyhee Canyon Wilderness Study Area (OR-003-110) in order to evaluate its identified mineral resources. The study area is in Malheur County, OR, about 8 miles north of Rome. There are approximately 7.7 million tons of subeconomic zeolite (heulandite and/or clinoptilolite) resources with ammonia ion exchange capacities as high as 1.75 milliequivalents per gram in the Chalk Basin-Lambert Rocks area. The bed is 25 ft thick with less than 100 feet of overburden. This resource probably will not be mined in the foreseeable future.

Jan 1, 1989

By T. A. Lang

The objective was to develop a Program Plan of analytical studies and tests for determining ( 1) the optimum installation tension of a coal mine roof bolt, (2) the most valid bolt support theory or theories, and ( 3) the most valid roof failure theory or theories. On this basis a comprehensive literature search was made and significant material dealing with coal mine roof behavior, roof bolting and roof support was collected, reviewed, classified and analyzed. Emphasis was given to the influence of rock reinforcement on the control of deformation, stress field modification and mine roof stability. An assessment was made of the effect of various parameters including bolt tension, bolt pattern and time of installation, on the effectiveness of rock reinforcement systems, and equations developed for bolt tension as a function of these parameters, and rock properties. From these studies, a major program plan of tests and studies was developed for verifying and validating the most tenable theories of roof behavior and roof support and for determining optimum bolt installation tension.

Jan 1, 1979

By E. P. Carman

In this report, the Federal Bureau of Mines presents a summary of the occurrence, properties, and uses of some natural bitumens, using the layman's or dictionary definition of bitumens - that is, naturally occurring hydro-carbons. Emphasis is on the less common solid and semisolid bitumens, particularly those occurring or used to some extent in the United States. This comprises data from many sources and references to these sources for more detail than is given in this summary. This paper was prepared primarily to answer questions about some of the less known bituminous materials. The word hydrocarbons could just as well have been substituted in the title for bitumens, but bitumens was used, since an abstract of the paper was presented at a meeting where the major emphasis was on bituminous materials. The reader will realize that coals, of which only the more unusual such as the cannel coals and torbanites are discussed in this paper, are primarily mixtures of bituminous materials and carbon. The amount of bituminous material, or volatile matter, in coals is greatest in the lower rank coals and the unusual types described in this paper, and decreases as coal rank increases. However, since no method other than destruction of the original coal substance by heat is known that will separate the volatile matter from the carbon, it appears reasonable to classify the coals with other bituminous materials, particularly since bituminous coal - the most widely used coal - by its name indicates the combination of bituminous materials and carbon.

Jan 1, 1961

By B. W. Gandrud

At the Southern Experiment Station of the Federal Bureau of Mines, reports are prepared from time to time on results of washability studies of commercially important coal beds in the Southern Appalachian region. The investigations that provide the material for these reports are made by the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama and the mine operators. This report records the results obtained on a sample of run-of-mine coal taken in June 1953 from the Pratt bed at the Davidson Coal Co. mine about 1 mile west of Graysville, Ala. One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield an acceptable grade of coking coal with a mini-mum of losses of coal in the rejects. The Pratt bed is one of the main sources of coking coal in the Jefferson County part of the Warrior field. This is the first time, however, that data from a complete washability study of coal have been obtained from this bed in Jefferson County. In the Graysville area, Pratt-bed coal has good coking characteristics and is used for blending with other coals in making metallurgical coal. The extent of its use in such blends is severely limited in this area, however, by the fact that it has a high sulfur content, which has not been reducible to any great extent by washery treatment.

Jan 1, 1955

By G. V. Sullivan

This report summarizes the results of metallurgical investigations by the Federal Bureau of Mines of manganese oxide ore, averaging 23 to 25 percent manganese, stockpiled at the Butte-Philipsburg depot of General Services Administration (GSA). The oxide ores were stockpiled in two general classifications, straight oxide ore and mixed oxide-carbonate ore. Continuous-circuit flotation tests at the Albany (Oreg.) Metallurgy Research Center of the Bureau of Mines showed that each of these ore types could be concentrated by an oil-emulsion scheme to produce a concentrate that could be sintered to meet program specifications. About 88 percent of the manganese was recovered in the concentrate from the straight oxide sample, with the sintered concentrate containing 48 percent Mn. The sintered concentrate from the mixed oxide-carbonate sample contained 41 percent Mn with a recovery in the concentrate of 95 percent.

Jan 1, 1961

By E. E. Maust

The present work is part of an ongoing Bureau of Mines effort to provide a better understanding of the fundamental phenomena involved in sulfide flotation, the role of oxygen in xanthate adsorption being one essential issue. Galena was chosen as the material around which to develop a conceptual model, partly because of its demonstrated oxygen sensitivity and partly because information on its properties and flotation behavior constitutes the largest part of the fundamental information available on sulfides of commercial importance. The model is formulated primarily in terms of surface electronic energy levels produced by oxygen and xanthate and is further developed using existing experimental evidence and its implications. Four major functions of oxygen are elucidated, and the relationship of these to the formation of lead xanthate, dixanthogen, and a surface compound is discussed. Though yet incomplete, the model provides a useful framework within which the results of diverse experiments can be related to one another in their proper perspective, as shown by a brief discussion and resolution of some apparently discordant results reported in the literature.

Jan 1, 1976