Search Documents

By A. F. Baker

Laboratory flotation of synthetic coal-pyrite mixtures and high-pyritic-sulfur coal indicated that ferric chloride (FeCl3), aluminum chloride (AIC13), chromium chloride (CrCl3), and cupric sulfate (CuSO4) are potential pyrite depressants. For each metal salt there appeared to be a range of pH values and optimum concentration for selectively depressing pyrite in coal flotation. Pyrite was depressed in the pH range from 4.5 to 7.0 with ferric chloride, from 5.8 to 7.0 with aluminum chloride, from 6.4 to 7.1 with chromium chloride, and from 6.4 to 7.4 with cupric sulfate. Best separation of pyrite from coal was achieved in flotation solutions containing from 2 X 10-5 to 5 x 10-5 mole/ liter of each salt. In solutions containing excess salt concentrations, coal was also depressed. These Bureau of Mines tests demonstrated on a laboratory scale that, in solutions containing 4 X 10-5 mole/liter ferric chloride and from 1 x 10-4 to 2 x 10-4 mole/liter sodium hydroxide, the pyritic sulfur content of a Lower Freeport bed coal sample could be reduced from about 2.51 percent to less than 0.60 percent with recoveries of over 83 percent. The depression of pyrite appears to be due to the adsorption of positively charged colloidal metal hydroxide at the pyrite-solution interface. This hypothesis is supported by zeta potential determinations which showed that suspended coal and pyrite particles in solutions containing metal salts are positively charged in the pH range where depression occurs.

Jan 1, 1971

By R. L. Montgomery

Heats of solution of yttrium chloride and oxide in hydrochloric acid were measured by Bureau of Mines researchers. Using the heat of combustion of yttrium mentioned in the literature, the Bureau calculated the heat of formation of yttrium chloride to be -239.16 + 0.50 kcal./mole. The Bureau experiments gave evidence that the heats of solution of yttrium chloride from the literature are mostly too low because of water and/or oxychloride impurities. Heat of combustion of yttrium (8)3/ and its heat of solution in hydrochloric acid (2, 14) have been measured. The earlier heat of solution measurement (2) is unreliable because of possible potassium contamination (4). Heat of solution of yttrium chloride has been measured by three researchers (3, 9, 15), who obtained widely different results. Spedding and Flynn (14) report the heat of formation of yttrium chloride as -232.69 kcal./mole from their solution studies. The present work was designed to check the reported heats of solution of yttrium chloride and to determine the heat of solution of yttrium oxide. The latter measurement would allow the results of solution and combustion data for yttrium to be intercompared.

Jan 1, 1960

By Forrest T. Moyer

THE injury data and experience in this bulletin are presented in three general sections. The first section contains general and detailed data relating to 1948 injury experience in bituminous-coal and Pennsylvania anthracite mines, separately and combined into totals for all coal mines. The related employment, worktime, production, and productivity data are given in each breakdown of the statistical data. Tables 1 through 22 constitute a subsection and present statistics on number of injuries, frequency and severity rates, average severity, detailed and major causes of injuries, injury records of the coal-producing States, distribution of injuries by part of body, and distribution of injuries by days of disability. Tables 23 through 45, the second subsection, present injury experience in bituminous-coal mines by various selected factors of physical or operating conditions that ma contribute to the occurrence of injuries. The degree of mechanical loading, productivity, size of mine by number of men working and by tonnage mined, thickness of bed, length of shift, number of shifts, type of cap lamps, rating of mine as gassy or nongassy, type of ventilation, and combinations of these factors influencing mine safety are presented in this group of tables. Similar data on Pennsylvania anthracite mines are listed in tables 46 through 63, which comprise the third subsection. The second section of the report contains the generalized annual injury records of bituminous-coal, Pennsylvania anthracite, and all coal mines from the earliest available data through 1948. Tables 64 through 97 list the number of fatal and nonfatal injuries, injury rates, and causes of injuries on an industry basis, the long-term injury records of each coal-producing State, and the related employment, worktime, and production data.

Jan 1, 1952

By Wilbur L. Webb

This publication reports on the design, fabrication and test of an Improved methane monitor system for compliance to 30CFR75.313. The system will Initiate automatic shutdown of mining machinery when excessive concentrations of methane are encountered. The prime consideration: In the design were small size, Improved accuracy and reliability, fast response and a transient resistant power supply capable of reliable operation from any mine power source. The power supply contains an internal battery that provides operating power to the detection system prior to mining machine start-up or after machine shutdown. This report documents the development program from conception through in-mine testing.

Jan 1, 1978

By M. D. Marshall

A survey showed that there were 24 bin-related fatalities in the 5 year period of 1975 to 1979 in the minerals industry. Only 4 victims wore safety belts and only 1 of these had a second person attending his lifeline, as mandated by Federal safety regulations. Not one victim observed the three main Federal safety regulations governing work in and around bins. A study was conducted on the force necessary to pull victims partially buried in sand and limestone. Recommendations are made on procedures and safety equipment that can minimize bin-related accidents. A Handbook, directed to the plant engineer responsible for bin design and safety, was also issued detailing bin designs and flow-aid accessories as a function of the flowability of the stored material to better maintain material flow from bins. A comprehensive table of the flowability of many materials produced in the minerals industry is presented and simple procedures given for determining the flowability of materials if not available.

Jan 1, 1984

By G. L. Neumann

The Guymard mine in Orange County, N. Y., is reported to have been discovered in 1862 and mined until 1876, producing 10,000 tons of lead and zinc ore. The property was examined by an engineer of the Bureau of Mines in 1948. Development work was done by the Bureau in April and May 1949 and March 1950. During these two periods four drill holes totaling 2,090 feet were completed. The mineralized sections of the core were sampled and assayed.

Jan 1, 1952

By Raja V. Ramani

Productive and beneficial use of reclaimed surface-mined land is a concern of industry, government, and the general public. An investigation was conducted of current mined-land planning practices to aid in the development of a procedure for evaluating postmining land use potentials. This investigation considered both the industry and public planning approach to mined-land planning. It included a detailed review of the impact of regulation, factors that determine land use, and current site planning methods employed by the mining industry. The methods of this investigation included three in-depth case studies of surface mines in the eastern, central, and western United States. A site planning pro-cess has been developed and applied to the surface mine case studies to evaluate the economic, environmental and social impacts of postmining land use alternatives. In add it ion, guidelines are proposed to enhance the cooperation between local land use planners and surface mine planners, as well as to improve comprehensive planning with regard to mineral resources at the local and regional level.

Jan 1, 1983

By J. B. Salsman

As part of the research effort on investigating the effects of microwave energy on the chemical and physical properties of minerals and ores, the U.S. Bureau of Mines (USBM) Tuscaloosa Research Center has conducted research to measure the dielectric properties of these materials. The objective was to establish a reliable database for use in predicting the effects of microwave heating on a wide range of minerals. The dielectric constants and loss factors of minerals, commonly referred to as the dielectric properties, were determined utilizing the theory of microwave propagation through an open-ended, air-filled coaxial line that was terminated at its open end with the particular mineral under investigation. In this phase of microwave research, the USBM measured the dielectric properties of powdered minerals with medium to high electrical conductivities in the frequency range of 300 MHz to 3 GHz and as a function of temperature from 25 to 325 °C. Since the minerals were prepared as powders, techniques were used to relate the measured dielectric properties of the powdered minerals to the dielectric properties of the mineral at its theoretical or natural density.

Jan 1, 2010

By Alphonso Cornejo, Galen H. Clevenger

This bibliography was compiled in connection with an investigation of the Caron process for the treatment of manganese - silver ores , conducted by the T. S. Bureau of Mines in cooperation with the Netherlands East Indies Government . The object of this investigation was to develop a practicable method for treating the refractory manganese- silver ores found in these two countries . The results of the work will be published as a bulletin of the Bureau of Mines . This bibliography summarizes the available information on the subject previous to the investigative work embodied in the forthcoming bulletin, and may be useful to those metallurgists or others conducting work along this line .

Mar 1, 1923

By Van E. Shaw, D. J. Bauer

Conversion of euxenite concentrate to sulfates with sulfuric acid and solvent extraction of the yttrium- rare - earth mixture with EHPA were studied to determine extraction and separation characteristics . Digestion with 3.5 pounds of 96 percent sulfuric acid per pound of concentrate at 336 ° C for 4 hours resulted in an easily handled product with a yield in excess of 98 per- A thorium- free product was obtained by calcining the sulfated material for 3.5 hours at 650 ° C prior to leaching with water . Di ( 2 - ethylhexyl ) phosphoric acid solvent is an effective extractant with preference for cerium ( IV ) and heavy - group rare - earth elements including yttrium . Separation of complex rare - earth mixtures into light- and heavy - group fractions is feasible , and these fractions can be further processed to isolate ytterbium , neodymium , and dysprosium by changing processing conditions to obtain separation factors greater than two between these and adjacent elements .

Jan 1, 1965

By Terry R. Neumann

In 1987 and 1988, the U.S. Bureau of Mines conducted a mineral resource investigation of the 31,400-acre Muddy Creek Wilderness Study Area (UT-060-007). The investigation was requested by the Bureau of Land Management and authorized by the Federal Land Policy and Management Act of 1976 (Public Law 94-579). The study area is located in Emery County, Utah, about 50 air-miles southwest of Green River, Utah. The wilderness study area is in the San Rafael Swell region of the Colorado Plateau Physiographic Province. Rocks in the area consist of gently dipping sedimentary strata of Permian, Triassic, and Jurassic age.

Jan 1, 1988

By Irving Hartmann, John Nagy

"The pressures produced by dust explosions are frequently so great and are developed so rapidly that widespread destruction of manufacturing equipment and buildings results. Experimental data on maximum pressures and rates of pressure rise produced in a closed vessel by numerous metal powders and by dusts used in the plastics industry were published in two previous Bureau of Mines papers.4/5/One means for reducing structural damage is provision in the enclosing walls and/or roof of rapidly opening explosion-relieving devices or relief vents through which the pressure of an incipient dust explosion can be quickly dissipated. The vents can be simply unrestricted or free openings: hinged or pivoted sash which swing outward at a predetermined internal pressure; fixed sash, with light wall anchorages; scored glass panes; light wall panels; monitors or skylights; poppet-type vent closures; paper, metal foil, or other diaphragms that burst at low pressures; pull-out diaphragms, or other similar arrangements.The use of pressure-relief vents is recommended in the dust-explosion codes of the rational Fire Protection Association,6/ and recently a special committee on explosion venting has been organized. However, technical data on which the design and distribution of relief vents can be based are meager. An experimental study on venting grain-dust and cornstarch explosions was made by the Bureau of Chemistry and Soils, United States Department of Agriculture.7/ Tests on cork fines, cinnamon, starch, barley dust, and a phenolic plastic were made in a laboratory-scale (0.1-cubic-foot) apparatus by the engineering department of the Factory Insurance Association.8/ A study on the venting of explosions of acetone-air mixtures was made by the Bureau of Mines.9/The object of the present investigation is to extend the limited knowledge on the effectiveness of pressure-relief vents of different types, shapes, and sizes. The aim is to determine the venting requirements in equipment and structures of various dimensions and shapes for dusts of widely different explosive properties. On the basis of such accumulated information, together with theoretical considerations, it is hoped that ultimately it will be possible to recommend correct venting for most operations in which a dust-explosion hazard exists."

May 1, 1946

By Walter W. Fowkes

Leonardite is a coallike substance, similar in structure and composition to lignitic coal and believed to be derived from lignitic coal by the process of natural oxidation. Leonardite is little known outside lignite-producing areas and has been developed commercially only to a minor extent. The higher oxygen content and less compact structure of leonardite, compared with lignite, make it undesirable as a fuel but indicate that it has potential as a source of chemicals and for other nonfuel uses. It is a convenient source of humic acids. The United States has a large natural reserve of leonardite; furthermore, it can be produced in the laboratory under controlled conditions. The significant elemental difference between leonardite and lignite is the oxygen content (leonardite, 28-29 percent; lignite, 19-20 percent). The higher oxygen content of leonardite is due entirely to a Larger number of carboxylic acid groups. This fact explains the 17-Cold increase in alkali solubility of leonardite. Spectral studies indicate that the material is mixed salts of humic acids.

Jan 1, 1960

By H. B. Brunot, L. C. IlsLey, E. J. Gleim

"INTRODUCTION To supply inspectors, safety engineers, and others with detailed information as to the safety features of the various electrically operated machines that have been approved as permissible by the Bureau of Mines, three bulletins and five reports of investigations have been published dealing with the various classes of approved machines:Bull. 313, Permissible Storage-Battery Locomotives and Power Trucks.Bull, 343, Permissible Coal-Handling Equipment Approved from January 1926 to December 1930, inclusive.Bull. 382, Permissible Coal-Cutting Equipment Approved Prior to July 1, 1932.Rep. of Investigations 3309, Permissible Electrically Operated. Air Compressors.Rep. of Investigations 3326, Permissible Electrically Operated Room Hoists.Rep. of Investigations 3345, Permissible Electrically Operated Rock-Dust Distributors.Rep. of Investigations 3363, Permissible Electrically Operated Hand-Held Coal Drills.Rep. of Investigations 3391, Permissible Electrically Operated Post Drills and Drilling Machines.The present paper gives similar information relative to the mine pumps approved before October 1, 1939."

Mar 1, 1940

As part of a continuing program of evaluating the Nation's crude-oil resource, this report presents information pertaining to resource, primary reserve, and potential waterflood reserve for 3,209 selected reservoirs contained in 24 oil-producing States, as of January 1, 1968. To that date the selected reservoirs had not been subjected to pressure-maintenance or secondary-recovery operations. These reservoirs also met the following parameters: (1) a minimum of five oil-producing wells on January 1, 1968, (2) a minimum of 50 acres areal extent, (3) a minimum of 50,000 bbl of oil ultimate primary recovery, and (4) the principal reservoir energy was other than active water encroachment. The selected 3,209 reservoirs produced 527 million bbl of oil in 1967, about 17 pct of U.S, total production. Primary oil reserve was 4,983 million stb; in addition, there was 6,043 million stb of potential water- flood oil reserve. Oil resource in the selected reservoirs was 59,547 million stb. A brief history and outlook of waterflooding are presented for each State. Depth and producing rate statistics and geologic distributions of production, resource, reserve, and potential waterflood reserve for the selected reservoirs are presented by States in the appendix. Also included in the appendix are description, history, and technique modifications of waterflooding, and a preliminary cost estimate of a closed-system water-injection project.

Jan 1, 1970

By Elger. G. W.

The Bureau of Mines investigated preheating of continuously fed, fragmented ferrous scrap charges by furnace offgases and utilizing substitutes for imported fluorspar to condition electric steelmaking slags. Three types of continuous scrap charging procedures were investigated to determine electrical energy consumption in a I-st (short ton) electric arc furnace. Cold and preheated scrap charges were continuously fed at rates averaging 37.5 and 43.7lb/min, respectively. The feed rate varied appreciably from test to test owing to hangup of the scrap in the charge bin. Approximately 7 pct less electrical energy was consumed in melting scrap preheated to 8400 to 1,1100 F by furnace off-gases than in melting cold scrap. Overall energy consumptions were 888 kW'h/st for cold scrap, 829 kW'h/st for preheated scrap" and 637 kW'h/st for conventional backcharged scrap. Stack gases from scrap preheating averaged 1200 F and a flow rate of 1,615 scfm compared with 2200 F and 1,302 sefm for cold-charged scrap. Slag conditioners tested included synthetic fluorspar, boric acid, hydroboracite, used aluminum potlining wastes and aluminum anode tailing wastes, and Sorelflux B. The boron-containing conditioners fluidized the slags the best, followed in order by the conditioners containing fluorine and titanium.

Jan 1, 1987

By Jr. Jacobson

Thermal reactions of l-methylpyrrole, l-butylpyrrole, and l-isopropyl-pyrrole were investigated by a flow method in the temperature range of 4500 to 5750 C. Those of I-butylpyrrole and l-isopropylpyrrole were also investigated in the 3400 to 4000 C range in a static system. The I-substituted pyrroles isomerize by an irreversible reaction to 2-substituted pyrroles. A reversible isomerization reaction shifted the alkyl group from the 2-to the 3-position on the pyrrole ring. All of the isomerization reactions are homogeneous, unimolecular, nonchain, first-order reactions having similar mechanisms and transition states. There is decomposition and cleavage of the longer alkyl side chain when it is in either the 2-or 3-position giving, as products, pyrrole, 2-and 3-methylpyrrole, 2-and 3-ethylpyrrole, pyridines, and hydrocarbons. The decomposition reactions appear to be by free-radical mechanisms. Pyridine homologs are formed by the expansion of the alkylpyrrole: butylpyrrole produces pyridine, and isopropylpyrrole produces 3-methylpyridine. Approximate Arrhenius equations are given for the formation of the decomposition products.

Jan 1, 1966

By J. D. Davis

The carbonizing properties of No. 2-bed coal from the Bartoy mine and No. 5- or Miller-bed coal from the Wilkeson-Miller mine, both at Wilkeson, Pierce County, Wash., were determined by the Bureau of Mines-American Gas Association (BM-AGA) method. Tests were made in the 13-inch retort at 500°, 600°, and 700° C. and in the 18¬inch retort at 800°, 900°, and 1,000° C. Fischer low-temperature and United States Steel Corporation high-temperature assays were made and the results compared with those of the BM-AGA tests at corresponding temperatures. Agglutinating and plastic properties were determined, and chemical and petrographic analyses were made. The No. 2 bed is 58.5 to 88.0 inches thick at three points sampled in the Bartoy mine. The coal is 98 percent bright and contains only a trace of fusain. A composite of three mine samples contained 13.8 percent ash. The washed sample, which was used in the tests described herein, contained 11.4 percent ash, 2.2 percent moisture, and 0.6 percent sulfur upon the as-carbonized basis and 68.4 percent fixed carbon upon the dry, mineral-matter-free basis. The heating value was 15,183 B. t.u. per pound upon the moist, mineral-matter-free basis. No. 2 therefore ranks as a high-volatile A coal and is very high in that, rank. The ash softens at 2,910° F. Except for its ash content, which is higher than the limit of 9.0 percent specified by the American Society for Testing Materials, No. 2 coal fulfills the requirements of a coking coal. It also is classed as extremely friable, the friability being 88.0 percent. The agglutinating index (7.6 for the 15 : 1 ratio of silicon carbide to coal) is high, and the plasticity as indicated by the Gieseler test (60 divisions per minute) is low for a high-volatile A coal.

Jan 1, 1942

By J. P. Powell

The application of secondary producing methods for recovering additional oil from known fields has been recognized for many years as important to the economy of the nation. One of the most successful secondary methods is waterflooding, which conserves our natural resources by preventing premature abandoment of stripper leases and revitalizing previously abandoned areas. Waterflooding as a secondary-recovery method was introduced into the Midcontinent region in 1931, and its use as such has become widespread. As with most new methods, the most favorable fields and leases received primary attention, whereas those with viscous oil or less favorable sand characteristics were bypassed. Numerous reports3 4 5 6/ have been published giving the results of individual waterflooding projects, In this report, attention is directed to the effect of a single factor, the viscosity of the oil produced,

Jan 1, 1959

By J. L. Reuss

The Bureau of Mines derived information on the softening characteristics of both unfired and indurated iron ore pellets as measured by hot compression strength in a laboratory study. A surprisingly high hot strength (240 1b per ½ -inch spheroid) was developed by unfired magnetite pellets near 900° C; lesser maxima were developed by pellets made from hematite and specularite concentrates near 1,000° C. Those from goethite remained weak throughout the pre induration heating. Fully indurated commercial pellets retain a high resistance to softening when heated in air. On the contrary, in a hot reduing atmosphere their high cold crushing strength dissipates rapidly. At 1,000° C, for example, the average compression strength of seven different commercial pellets was 110 lb; at 1,100° C, the hot strength was only 60 lb. After a rather sharp initial drop, the loss of strength with increase of temperature was gradual. There was no sudden collapse, nor any significant difference, in behavior of commercial pellets whether made from magnetite or hematite concentrates.

Jan 1, 1968