Search Documents

By W. C. McBee

Technology for the preparation of densifiable sulfur concrete (sulfapave) materials has been devised by the Bureau of Mines. The materials are intended as new construction materials for use in corrosive areas where conventional materials fail. A series of modified sulfur cements were developed, which can be used in combination with dense-graded aggregates to prepare sulfapave materials with excellent corrosion-resistant properties. The materials can be mixed, laid, and compacted into place with conventional hot-mix asphalt pavi.ng equipment. Mixture designs utilizing 5-to 30-pct-modified sulfur cements and dense-graded aggregates gave material properties ranging from rigid to flexible. Laboratory corrosion tests in sulfuric acid showed no material loss or deterioration of physical properties over a 1-year test period in concentrations ranging from 0 to 60 pct at ambient temperatures. Preliminary results on field testing the materials for durability to weathering, corrosion, and traffic have been excellent, with no evidence of failure in the materials.

Jan 1, 1985

By Alden H. Emery, J. J. Forbes

"IntroductionThe data contained in this paper were collected during the course of an investigation which covered 15 representative coal mines in 6 coal-mining States. The purpose of the investigation was to determine by atmospheric sampling how much dust was raised into the air during the various operations of coal mining, such as undercutting with machines, loading coal by hand, and transporting it from the working face to the surface. The data thus obtained were considered from two angles - namely, the possible physiological effect of inhalation and the explosion hazard of the dust. No attempt will be mode to discuss the former factor in this paper.CONDITIONS OF MININGThe mines in which this investigation was conducted were considered representative, and it is believed that the results obtained will suffice for the average dustiness encountered in most coal mines. .All of the coal mined was bituminous, from beds 30 to 120 inches thick. Only the ordinary room-and-pillar system of mining was employed. Daily production ranged from approximately 700 to 1500 tons and the men employed from 150 to 450. Coal was undercut by short-wall mining machines in all mines, with the exception of one in which pick mining was employed. Loading at the face was done by miners; none of the mines used mechanical loaders. Electric drills, both for brushing roof and for shooting coal, were commonly used although some roof work was done with jack-hammers and a. little of both with augers. Coal was hauled by motor, mule, or rope power in end-gate cars with capacities ranging from 1600 to 3600 pounds. With few exceptions, coal was won at the face by dry methods - that is to say, no water was employed fox wetting down the dust either during undercutting, loading, or transportation."

Feb 1, 1927

By Ellsworth Y. Dougherty, Edwards F. Fitzhugh

"INTRODUCTION During the summer of 1945 the Bureau of Mines made approximately 200 miles of reconnaissance magnetic surveys in north-central Mirnesota. The survey started near the western end of the Mesabi Iron Range and extended into the area to the southwest, west, and northwest and also southward to the-northern limits of the Cuyuna Iron Range. The purpose of the survey was to data to assist exploration for iron ore in the region through:1. Supplying a relatively unit form network of traverses, by which and future surveys of localities in the urea ray be correlated. Suggesting localities in which more detailed magnetic surveys may be justified, and, Disclosing localities in which there is lass hope of obtaining significant results from further magnetic surveys.The instrument used was a Hotchkiss Superdip, and traverses for calibration and comparison were run with a Schmidt-type magnetometer. Field observations and work directly related thereto were carried out under contract by E. J. Lang-year Co., Minneapolis. Engineers of the Bureau of Mines planned, directed, and reviewed the survey."

Aug 1, 1946

By Robert P. Vinson

This Bureau of Mines report presents the results of tracer gas studies conducted at three facilities where bagger hoods had been installed several years ago to remove airborne silica dust from the vicinity of the bagging operator. The studies indicated that for optimum benefits makeup air must be evenly dispersed, the hood enclosures and duct systems must be as airtight as possible, the average intake air velocity of each hood should be at least 200 fpm, and the hoods and duct systems must be properly maintained.

Jan 1, 1981

By M. Karmis

Surface subsidence is an inevitable consequence of many underground mining operations and has been recognized as such since the fifteenth century. Damage resulting from this phenomenon ranges from simple land settlement to severe structural damage to buildings and has been witnessed in rural (Illinois, Colorado, West Virginia, Virginia, Pennsylvania) as well as in urban areas (Pennsylvania, West Virginia, Illinois, Wyoming). In fact, it is estimated that over 2 million acres of land across the United States have been affected by mining subsidence, of which 140,000 acres are in urban areas (Singh, 1978; Johnson and Miller, 1979). Further, it is estimated that during the next twenty years an additional 1.5 to 2.4 million acres of land will also be affected by mining. Subsidence prevention is not feasible, at least under the existing technologic and economic constraints of underground coal mining. Foreign experience has demonstrated, however, that subsidence can be successfully controlled if an accurate method of predicting ground movements is available. Such techniques have been developed in many coalfields, where it is currently accepted that subsidence can be predicted within ± 20 percent of the actual values. Furthermore, such movements can be translated into anticipated structural failures using established damage criteria, thus enabling appropriate precautionary measures to be implemented.

Jan 1, 1983

By J. E. Spurr

"Zinc Industry in BelgiumBy March F. Chase, Consulting Metallurgist, Bureau of MinesBelgium for many years was the principal spelter producing country of the world. Gradually its production was surpassed by that of Germany, and Germany in turn lost first place by the production in the 77ti.tad States. For the ten years previous to 1914, 21.6 per cent of the world's spelter was produced in Belgium. Of this production approximately 40 per cent was exported. A large percentage of the balance was rolled and of the shoots thus produced a considerable quantity was also exported.From an economic standpoint even before the war, the Belgian industry was in a unique, if not praoarious, position. Dependent upon foreign countries for ore and foreign markets for sale of products, smeltor was at a distinct disadvantage when compared with some of those of other localities. These disadvantages were partly offset by cheap coal and labor and by whatever there is of value in experience and what we may term for want of a better expression smelting tradition. However intangible this latter may be, it did have and has today an influence on commercial operations.One must not overlook the effect it will have on the revival of the industry. It may not be the determining factor but the fact that for so many years this industry flourished in Belgium, and played such an important role in the industrial life of the country will decide many operators to attempt to re-establish their operations.In 1913 the Belgian spelter plants produced 204,220 long tons of spelter or approximately 20 per cent of the world's production. During this year 500,000 to of ore were treated. The actual value of all of the products derived from treating sine ore amounted to 225 million frames."

May 1, 1919

By Sarkis G. Ampian

Published optical microscopic and X- ray diffraction characteristics of the following compounds are critically evaluated and compared with Bureau of Mines data : Tricalcium aluminate , calcium monoa luminate , dodecacalcium heptaluminate , dicalcium silicate , tricalcium silicate , and sodium aluminate . A recommended set of definitive optical and X- ray diffraction characteristics is presented . These values are used to identify products of the lime soda sinter process for production of alumina . Polymorphism of gamma- , beta- , and alpha prime - dicalcium silicate is reexamined , and new data are presented on polymorphism of tricalcium silicate and sodium aluminate by high- temperature X- ray diffractometry . Polymorphism is not observed for tricalcium aluminate , calcium monoaluminate , and dodecacalcium heptaluminate . Bureau of Mines data indicating a stoichiometry of 12Ca0.7A10 for the phase 5Ca0.3A1 0₂ are discussed . A critical review of the literature concerning calcium dia luminate and sodium undecaluminate ( 8 -A10 ) is also included .

Jan 1, 1964

By Sabri Ergun

NEW theoretical data are presented for the intensity of X-rays diffracted from randomly oriented aromatic and alicyclic molecules and diamondlike structures such as are found in coals, cokes, and carbonaceous materials. Data have been computed using the Debye interference function. Computations for the smaller molecules have been made with the Univac 1204 computer: those for large structures, with either the IBM 704 or Bendix G-20 computer. A brief theoretical introduction of the Dobye interference function is given, and an outline is made of the treatment of experimental data so that the experimental interference function can be obtained.

Jan 1, 1965

By NORA Mining Sector Council

The National Occupational Research Agenda (NORA) is a partnership program to stimulate innovative research and workplace interventions. In combination with other initiatives, the products of this program are expected to reduce the occurrence of injuries and illnesses at work. Unveiled in 1996, NORA has become a research framework for the National Institute for Occupational Safety and Health (NIOSH) and the United States. Diverse parties collaborate to identify the most critical issues in workplace safety and health and develop research objectives for addressing those issues. NORA entered its third decade in 2016 with an enhanced structure. The 10 sectors formed for the second decade will continue to prioritize occupational safety and health research by major areas of the U.S. economy. In addition, NORA’s seven cross-sectors will continue to focus on the major health and safety issues affecting the U.S. working population. While NIOSH serves as the steward to move this effort forward, it is truly a national effort. NORA is carried out through councils comprised of members with many diverse interests that are developing and implementing research agendas for the occupational safety and health community over the third decade (2016-2026) of NORA. Councils address objectives through information exchange, partnership building, and enhanced dissemination and implementation of evidenced-based solutions. NORA groups industries into 10 sectors using North American Industry Classification System (NAICS) codes. The Mining Sector encompasses NAICS code grouping 21xxxx where “xxxx” represents the different subcodes of the mining “21” classification. Mining encompasses the extraction of solid mineral and mineral-like substances from their place in the Earth’s crust and supplies them to processing industries that produce economically valuable materials. It does not include oil and gas extraction. The Mine Safety and Health Administration, MSHA separates mining into coal, underground and surface, and metal and nonmetal, underground and surface.

Feb 1, 2024

By E. V. Deshayes, W. E. Young

"INTRODUCTION The Camp Bird mine was investigated by Bureau of Mines engineers 3/ September 22 and 24, 1942, and April 29 and 30, 1944. In a subsequent report and supplement, it was recommended that core drilling be done below the 14th. level to determine if commercial ore existed at greater depths, and particularly if ore existed in the vein or adjacent thereto where it passes into the sedimentary formations estimated to underlie the volcanics approximately 400 feet below the 14th level.Seven diamond-drill holes aggregating 3,956 feet were drilled. Four of these holes were under the Hematite ore body and three were under the Big Discovery ore body. Two holes under, the Hematite ore body wore directed at angles but little steeper than the angle of dip of the vein and penetrated the sedimentaries beneath the volcanics close to the vein. Enough low-grade ore was found at the base of the Telluride conglomerate to indicate the presence of a large body of low-grade zinc sulfide ore. Two holes were directed to crosscut the vein at a depth of approximately 125 feet below the 14th level. No commercial ore was cut, but the vein showed the average width and same general characteristics as at the 14th level. One hole under the Big Discovery ore body was directed to crosscut the vein and test the base of the Telluride conglomerate in the footwall block. No commercial ore was found in either the vein or the sedimentary horizon. One hole was directed to test the base of the Telluride conglomerate in close proximity to the vein in the hanging-wall block. This hole was lost approximately 100 feet short of its objective, and a third hole was drilled to accomplish this same thing. The third hole was stopped approximately 50 feet short of its objective when failure of equipment caused a recess of the"

May 1, 1948

By Otis E. Perkins

This paper is one of a series being prepared for the United States Bureau of Mines to disseminate technical information retarding the methods used in mining nonmetallic minerals. The cost tabulations represent operating expenditures only and not total costs. It is recognized that publication of total costs might in many instances cause embarrassment to individual operators as well as to the industry as a whole. On the other hand, operating costs are essential to the technical discussion and study of the methods employed. The attention of the reader is specifically called to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. This paper deals particularly with methods and costs of dredging, classifying materials, and transportation at the plant of the Ross Island Sand & Gravel Co. of Portland, Ore. ACKNOWLEDGMENTS The author wishes to acknowledge the assistance of Harold Blake, general manager of the company, and of A. V. Kramer, cashier in charge of the plant office.

Jan 1, 1933

By M. M. Fine

"INTRODUCTION One of the principal activities of the Bureau of Mines during the recent war was to help to increase the supply of strategic and critical minerals. Fluorite was one of the most critical of the nonmetallic minerals because of the increased demand for it as a flux in basic open-hearth and electric steel furnaces and as a raw material for the production of artificial cryolite used in the aluminum industry. Wartime developments in the technology of hydro-fluoric acid, such as the use of the anhydrous acid as a catalyst in high-octane-gasoline production and the use of organic fluorides as carriers for insecticides, also increased the demand for acid-grade fluorspar. 2/ In 1943 the consumption of acid-grade fluorspar was advancing at a more rapid rate than production and was only slightly less than production during the latter half of the year.The outlook for the postwar market for fluorspar is encouraging. Steel production is expected to remain high until the domestic demand for commodities not manufactured during the war is satisfied. The uses for hydrofluoric acid also are expected to increase under the impetus of war-initiated research. In consideration of these and other factors some authorities predict a new peacetime demand for fluorspar equal to 60 to 75 percent of the war production, 5/ 6/ and others believe that the fluorspar industry will be permanently expanded. 7/"

Dec 1, 1947

By D. R. Tesarik

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars), and biaxial stressmeters (to measure stress changes in several support pillars and abutments). Two-and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 2010

By C. L. Karr

Researchers at the U.S. Bureau of Mines (USBM) have developed adaptive process control systems in which genetic algorithms (GA's) are used to augment fuzzy logic controllers (FLC's). GA's are search algorithms that rapidly locate near-optimum solutions to a wide spectrum of problems by loosely modeling the search procedures of natural genetics. FLC's are rule-based systems that efficiently manipulate a problem environment by modeling the "rule-of-thumb" strategy used in human decision-making. Together, GA's and FLC's include all of the capabilities necessary to produce powerful, efficient, and robust adaptive control systems. To perform efficiently, such control systems require a control element to manipulate the problem environment, an analysis element to recognize changes in the problem environment, and an adaptive element to adjust to the changes in the problem environment. The control system also employs a computer simulation of the problem environment. Details of an overall adaptive control system are discussed. A specific laboratory acid-base pH system is used to demonstrate the ideas presented; all results are from the physical laboratory system and not from a computer simulation.

Jan 1, 2010

By Robert M. Koerner

The feasibility of using small-scale models to simulate residential masonry foundation walls subject to fatigue loading was investigated. Five wall segments were modeled in one-quarter scale using dynamic similitude equations. The walls were dynamically loaded using a sinusoidal base motion and wall accelerations were monitored. The stiffness, natural frequency response, and damping characteristics were measured. The number of cycles of testing necessary to cause initial visible cracking was recorded. Analysis of the data indicated the importance of the relationship between the forcing function and the natural frequencies of the structure in influencing cracking damage.

Jan 1, 1980

By S. H. Lorain

Tin mining on Seward Peninsula, Alaska, has been intermittently active since the early 1900's. Most of the recorded production (over 2,200 short tons of metallic tin) has been obtained from placer deposits, but recent production also has resulted from development of lode deposits associated with intrusive rocks occurring in the western part of the peninsula. Generally, the lode deposits containing tin minerals (principally cassiterite) are found in dikes, in granite masses, and in silicate zones in limestone overlying the granite. Both the placer and lode deposits have been of considerable strategic interest to the Government because of the almost total absence of a domestic supply of tin. The most important tin-lode deposit discovered to date is in the Cassiterite dike at the Lost River mine, on Cassiterite Creek about 85 miles northwest of Nome. This highly altered, rhyolite porphyry dike averages 12 feet in thickness, strikes N. 75° to 85° E., and dips steeply to the south; it can be traced on the surface for about 8,000 feet. Throughout its explored length of about 2,200 feet the dike everywhere contains some tin and tungsten in veinlets and disseminations; economic concentration of the are minerals, however, is confined to definite shoots. The ore minerals include cassiterite, stannite, hulsite, paigeite, wolframite, scheelite, and base-metal sulfides; gangue minerals include fluorite, boron silicates, and lithium-bearing minerals. Some ore minerals also occur in the numerous other dikes and in the granite and intruded limestone in and adjacent to the mine.

Jan 1, 1958

By John D. Spencer

Air and water pollution and land reclamation relating to coal mining and utilization continued to be featured in research and technologic work on coal by the Bureau of Mines in 1967. Details of the environmental studies are given in this report, along with accounts of other research relating to the mining and utilization of coal. Other studies that were continued during 1967 included health and safety, mine explosives, coal preparation and transportation, coal utilization processes, chemistry and properties of coal, inspection and analysis, and inter-national activities. Publications issued in 1967 are cited throughout the report and in appendix C. Bureau of Mines research centers and laboratories are listed in appendix A, and organizations contributing to or cooperating in the work, in appendix B.

Jan 1, 1968

By Dale William Avery

Thirty mines and prospects were studied; 22 are within the Dolus Lakes RARE II area. Three properties within the area and one adjacent to it were determined to have indicated or inferred gold, silver, or molybdenum resources (fig. 1 and table 1) associated with quartz veins and shear zones or quartz-pyrite stockworks in granodiorite. Five other properties in the area and three just outside have potential for the discovery of gold and silver resources. Minor amounts of very fine-grained placer gold are in glacial outwash in and near the area. The John G. Carlisle Mine (fig. 1, no. 9) produced 120 oz (3.7 kg) of gold between 1897-1899. The Independence Mine produced 481 oz (15 kg) gold, 197 oz (6.1 kg) silver, and 189 lb (86 kg) of copper between 1926 and 1935. These mines are adjacent to the study area's northern boundary.

Jan 1, 1983

By Maria I. De Rosa

The U.S. Bureau of Mines conducted a study to determine if correlations exist between the chlorine or nitrogen contents of materials and the hydrogen chloride (HCI) or hydrogen cyanide (HCN) concentrations evolved during the thermal decomposition of these materials. Hydrogen chloride, hydrogen cyanide, and carbon monoxide (CO) were found to be the primary toxic gases evolved during the combustion process. The experiments were carried out in a 20-L furnace with 1-g samples. The furnace temperature, rising from ambient, was set at 1,000 °C with an airflow of 10 L/min. The variables measured were the gas loads (milligrams per gram) of HCI, HCN, CO, and CO2 (carbon dioxide); CO and CO2 concentrations as a function of time were also measured. Other variables included the average concentrations of submicrometer smoke particles and particles' average diameter, mass of particulates, sample and furnace temperatures, and sample weight loss. The data indicate that there are significant correlations between the percentage of chlorine or nitrogen contained in the original samples and the HC1 or HCN concentrations evolved during the combustion of the materials. These correlations may be used to predict and evaluate a material's toxic hazard during combustion.

Jan 1, 2010

By Donald J. Barnes

There are no producing or developing mines in the study area. The only mineral production was stone from a basalt deposit near Indian View Point. Cinders and sand and gravel have been produced from deposits within 1/2 mi (0.8 km) of the boundary. Stone, sand and gravel, and cinder deposits inside the area are not considered resources because equal or better quality material is found closer to markets. The study area has no known oil and gas, coal, geothermal, or other energy related deposits. However, in 1982 application was filed on 25,000 acres (10,125 ha) of petroleum and on 15,000 acres; (6,0/5 ha) of geothermal leases.

Jan 1, 1983