Search Documents

By J. Ronald Lawter

The purpose of the work described in this report was to measure the effects of diesel engine emissions on the air quality of work areas in a coal mine. Concentration measurements of a number of diesel related air contaminants were made at the Martin County Coal Corporation Mine in Inez, Kentucky. Compounds measured included carbon dioxide, carbon monoxide, formaldehyde, nitric oxide, and nitrogen dioxide. In addition, concentrations of the two classes of odorous compound;, aromatic hydrocarbons, and oxygenates were obtained along, with aldehyde concentrations. Surveys were made of the mine by odor analysts to determine the perceived intensity of diesel-produced odors. It was found that the concentrations of the measured species were well below their Threshold Limit Values. Odor intensity levels in the moderate to strong range were observed in the mine.

Jan 1, 1977

In attempting the predict coal cleat orientation in the subsurface for effective methane degasification of the coal beds in the Warrior coal field of Alabama, approximately 150 rock joint orientations and 45 coal cleat orientations were measured in each of 37 7 ½ minute quadrangles in Tuscaloosa, Walker, Jefferson, Fayette, Winston, Blount, and Bibb Counties. Data from these surface locations, and coal cleat data from eight underground mines was corrected for magnetic declination and titled beds rotated to the horizontal where necessary and plotted on rose diagrams for comparative analysis. Data collected on each joint and cleat consisted of attitude, quality, type, spacing, persistence, lithology, bedding thickness, surface texture, and filling. File data and published and unpublished reports from the State Survey and the State Mine Inspector's Office were re-viewed. Twenty-seven mining companies, most of which supplied information pertinant to the project were also contacted. The information obtained consisted of crop line information structure, and underground mine outlines, all of which were put on 7 ½ -minute topographic quadrangles. LANDSAT-1 imagery and Skylab photography were compared to dominant joint and cleat trends in the study area. Detailed results can be found in an open-file report entitled "Fracture Analyses in a Selected Area of the Warrior Coal Field, Alabama." A master's thesis entitled "The Relationship Between Surface Joints and Subsurface Structure in a Selected Area of the Warrior Coal Field" is being prepared to illustrate the relation-ship of the fracture system to the structure in the Warrior coal field. A proposal has been submitted for research on a project entitled "Rock Fracture Systems and Their Affects on the Extraction of Fossil Fuels in the Warrior Basin, Alabama"

Jan 1, 1976

By R. V. Ramani

This report is volume 10 of an eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment. The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation, and ventilation. This volume of the final report describes the Ventilation subsystem of the Master Design Simulator. The Ventilation subsystem has the capabilities to handle: (1) branches in parallel or series, (2) fans in parallel or series, (3) multiple fans, (4) methane, compressed air, or other injections into the system, (5) leakages and fixed quantities, and (6) calculations of absolute pressure at nodes. The program uses the Kirchoff's Junction and mesh laws, and the Hardy-Cross iterative technique to converge to the desired accuracy in solving fox the head quantity. A case study is included in the report illustrating the use of the model. The appendices of the report constitute a user's manual for the Ventilation subsystem, and include a program listing.

Jan 1, 1975

By Larry R. Powell

As part of the Bureau of Mines effort to establish a comprehensive subsidence data base for subsidence technology development, subsidence and related data are being compiled for various mining, geological, and environmental situations. This publication presents data for a longwall mining operation in the Northern Appalachian Coal Region. Vertical displacements and relative faze positions are tabulated for 160 subsidence monuments. Measurements were taken 32 times during the 2 years it took to mine the two panels. Brief physiographic and geological descriptions of the mining site are presented along with a general account of the mining and subsidence monitoring methods.

Jan 1, 1981

By L. G. Marshall

This report describes dredging and processing of sand and gravel from a glacial-fluvial deposit in the Raccoon River valley near West Des Moines, Iowa. Preliminary cleaning and separation of the sand and gravel at the dredge site with subsequent transportation to separate plants and the production and disposal of the various grades of aggregate material are also described. The geology of the deposit is summarized. A tabulated summary of costs in units of labor, power, and supplies is included.

Jan 1, 1963

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

By David K. Denton

Results of the mineral resource study of the Upper Priest Lake RARE II study area indicate a low potential for the discovery and economic recovery of silver and lead in the Prichard Formation near contacts with the Kaniksu Batholith in the vicinity of the Mountain Chief Mine (fig. 1). Silver and lead minerals locally occur disseminated and in irregular quartz fissure-fillings in the Prichard Formation. Between 18^6 and 1967, 105 lode raining claims were located in the study area. The area was designated for "further planning" in the Final Environmental statement but was later changed to "nonwilderness" by President Carter after work was scheduled for the area.

Jan 1, 1981

To develop a conceptual design for an automated longwall mining system, one should know what has been done, what is being done today and what is being planned for tomorrow. The bibliography referenced and discussed in this report provides a good source for that knowledge. To scientifically determine where attention should be focused to up-grade a system, the system must be quantized as far as possible. The Mechanization Profile of Appendix A-I is discussed in this report and has been used to analyze and determine the degree of mechanization currently in use and/or described in the literature for all three major elements of the long-wall system, namely, Winning, Roof Support and Haulage. The charted profiles make it self-evident where attention and design effort is needed to remove human operators from the face of the mine.

Jan 1, 1975

Four taconite plants were studied to establish the extent of hazard to plant personnel which exists based on long-term exposure to noise. The criteria for evaluation include the 90 dBA and 85 dBA summations of partial exposures. Data from extensive interviews were used to determine all work stations or locations which employees occupied and how much time they spent in ach location in a typical working day. Noise level measurements at every designated location were then made. By means of a computer program, these time and noise level data were us d to find the optimum noise reductions which would be required throughout each plant to meet both noise criteria. Subsequently, each plant was examined in detail so that the apparent sources of noise for each of the locations requiring noise reduction could be delineated. In tabular form, this report presents the hazardous locations for each plant, the existing noise level, the optimum noise reduction which would be required to meet the current and proposed laws, and the sources of noise which produce the existing noise level.

Jan 1, 1977

By William L. Crentz

Early in the nineteenth century, coal from Clearfield County entered the eastern commercial market. Ashley reports that coal was moved down the Susquehanna River by ark from Clearfield to Columbia, a distance of 260 miles, as early as 18o4. Around 1850, the famous Moshannon or Lower Freeport bed was discovered. Several years later the Moshannon Basin was developed extensively, and the coal from this area soon acquired an enviable reputation as a high-quality industrial fuel. Today much of the original Moshannon Basin coal is worked out, and the Lower Kittanning bed has replaced the Lower Freeport bed as the principal source of production in southeast Clearfield County. With depletion of the thick underground deposits, the importance 'of Clearfield County as a coal Producer would have diminished rapidly, if it had not been for strip mining the thinner beds. About 60 percent of the coal produced in the county is strip-mined, and the trend toward this mining method is expected to continue as the older underground operations are exhausted. Many strip mines are working in beds that are too thin to be recovered economically by any other method.

Jan 1, 1952

Demonstrate the technical feasibility of using nontraditional, low-rank, coal-based fuels and new coal-based technologies for mineral and metallurgical applications. Approach A cooperative research effort was initiated between the Bureau of Mines, U.S. Department of Energy and the minerals industry to extend the application of the fixed-bed gasification process to low-rank Western coals. The research effort enabled cooperators to gain operating experience in the use of hot, raw producer gas for iron ore pellet induration and other high-temperature mineral processes. Researchers were able to gather data regarding the fundamental engineering aspects of the fixed-bed process and gas cleanup for a wide range of solid fuel properties. Applying Fixed-Bed Gasification As a prerequisite to gathering the data needed for the study, the Bureau of Mines designed and installed, at one of its laboratories, a 6.5-ft-diam. single stage, fixed-bed, air-blown atmospheric pressure gasifier. The gasifier was coupled with a hot, raw gas combustion system and iron ore pellet in. duration kiln. The gasifier is rated at 1.5 ton/h capacity of bituminous coal.

Jan 1, 1987

By J. A. Kost

A dust-control manual was prepared for use by mine operations personnel. The manual documents state-of-the-art control techniques, dust sampling, and use of personal protective devices. Content addresses advantages/disadvantages of control techniques, design and operating specifications, and implementation and maintenance guidelines. An indexed list of selected references is also included. In addition to the completed manual, this report documents work performed in the course of its preparation.

Jan 1, 1981

By William H. Pomroy

The Bureau of Mines, through a 4-year program of combined in-house and contract research, has developed the necessary hardware and software technology to provide rugged, reliable automatic fire protection for surface mining mobile equipment. One element of this program was a continuing effort to help foster rapid mining industry acceptance of the technology by keeping end user costs reasonable. This report is an analysis of the economic impact of surface mining mobile equipment fires and the cost benefit of utilizing automatic fire protection systems to abate these losses.

Jan 1, 1982

By T. G. Carnahan

In-place leaching is being actively utilized to extract uranium, copper, and evaporites from low-grade and difficult-to-mine ores. The purpose of this report is to discuss in-place leaching technology, its advantages and disadvantages, and to give an overview of past, current, and envisioned in-place leaching operations in the U.S.A. Application of in-place leaching to uranium ores has been particularly successful because the conditions for leaching are nearly ideal. The ores are generally in highly permeable sandstone aquifers bounded above and below by impermeable shales. The uranium ore minerals are easily leached with oxidizing acid or base solution and the pregnant solutions are amenable to ion exchange concentration and purification prior to conventional solution neutralization for recovery of yellow cake. Copper is routinely recovered from sub-grade rock by dump leaching at most major copper mines. Acidified ferric sulfate is either sprayed on the surface of the dumps or is ponded on top of the dumps. The leaching solution migrates down through the rock and dissolves copper. The solution is collected from the base of the dumps and copper is recovered by solvent extraction-electrowinning or by cementation on detinned steel cans. True in-place copper leaching is being practiced in the caved stopes of an exhausted underground copper mine. Other innovative in-place copper leaching techniques have been tested commercially and laboratory- and pilot-scale experiments have been conducted to investigate proposed in-place leaching techniques for extracting copper from difficult-to-treat chalcopyrite ores. Solution mining of evaporites is being conducted commercially for the extraction of sodium chloride and potassium chloride. A large-scale experimental project for solution mining of trona has been undertaken.

Jan 1, 1982

By H. P. Rue

The Bureau of Mines has recently collected two samples of crude oil from wells in the Greasewood Flat area of northeastern Colorado. Sample 31310 was taken from the Continental Oil Co.'s well Briggs No. 1 which care in or September 27, 1931, with a maximum production of 940 barrels per day. Sample 31311 was taken from tie Reiter-Foster Oil Co. Is well Ida Johnson No. 1 which came in on August 24, 1931 with a maximum production of approximately 1000 barrels per day.

Jan 1, 1932

By Marvin S. Seppanen

Computer programers are often required to make modifications to unfamiliar Fortran routines. This Bureau of Mines report describes a computer program designed to aid the programer in such a situation by reorganizing: Fortran routines. This reorganization includes a sequential renumbering of the routine's statement numbers, a sequential renumbering, and relocation of format statements, an alphanumeric reordering of dimensioned and typed variables, a uniform pattern of text spacing, and a sequential numbering of the records in the final Fortran routine. The computer program has been extensively tested by the author and has proved to be a valuable tool for reorganizing Fortran routines developed under contract and later utilized by the Bureau, and for preparing routines for publication.

Jan 1, 1975

By Joe Maher

Adequate mine roof support to insure the safety of men and equipment is essential to successful mining. It is also expensive, amounting to more than one-fifth of the total mining cost at the White Pine mine. Cost effectiveness is therefore a prime consideration in developing optimum roof support. Roof bolt length is an important cost factor. This Phase II work compared uniform four-foot length Resin Bolts with the hitherto standard alternating four-foot and six-foot Resin Bolts, aiming at more cost-effective roof bolting. The data generated under this Phase II show that there is no discernible difference in the roof support given by uniform four-foot, and by alternating four- and six-foot, Resin Bolts in the relatively difficult ground selected for a severe initial test comparison; subsequent data from less difficult ground led to the same conclusion, namely no discernible difference between four-foot and four-six foot bolting.

Jan 1, 1975

The Objective: To reduce the noise generated by the exhausting air from a pneumatic roof bolting drill to a maximum of 90 decibels. Any attachment used for this purpose must be lightweight and must not cause a significant increase in back pressure. The Approach: Absorb the noise with a properly designed muffler that will permit sufficient airflow without affecting the normal operation of the drill. How It Works: The air exhausted by the drill enters the muffler through perforated disks into a resonator chamber. It then passes through a series of expansion and contraction chambers and is expelled to the atmosphere through another perforated disk. The basic muffler design for the pneumatic drill was established by using both digital computer analysis and experimentally simulated noise tests. The measured parameters used in the computer program consisted of inlet and outlet pressures, temperatures, airflows and exhaust areas. United

By R. Barany

This report contains the results of experimental work conducted by the Bureau of Mines to obtain the heats of formation at 298.15° K. of analcite, dehydrated analcite, lawsonite, anorthite, hexagonal anorthite, and leonhardite. Thermodynamic data for these minerals have applications in ceramics, extractive metallurgy, and particularly in geochemistry. Except for data on anorthite, no previous similar data existed. The present results will be a substantial aid in deriving the temperature-pressure-equilibrium relationships among these minerals. The heats of formation were determined by solution calorimetry, with hydrofluoric acid as the reaction medium. The results were expressed both in terms of the constituent oxides and in terms of the constituent elements. The heat of formation data were combined with related entropy values to obtain the free energies of formation at 298.15° K.

Jan 1, 1962

By J. R. Thoenen

The objective of this circular is threefold: First, to describe briefly the various modes of occurrence of sand and gravel. Second, to emphasize the need for adequate prospect¬ ing and exploration prior to the expenditure of funds for development and plant construction. Third, to describe various methods of prospecting and exploration and their application to the several modes of occurrence of sand and gravel. Sand and gravel may be found in nearly every county or township in the United States. Commercial deposits, however, are by no means so widespread. The introduction of concrete and the consequent impetus given to consumption of gravel and sand aggregates has seriously depleted deposits in some congested areas. Increasing re¬ strictions in the specification requirements for marketing sands and gravels have further narrowed the economic areas. On the other hand, the combination of increasing transportation costs and decreasing selling prices has forced the decentralization of gravel production. As a result smaller, intermittently operated, and widely scattered portable or semiportable unit plants have been encroaching on the territory formerly supplied from centrally located pits with large tr.atment plants. Generally speaking, the small portable plant can not produce any great variety of ma¬ terials to as exacting specifications nor as economically as the large permanent plant.

Dec 1, 1932