Search Documents

By I. Liebman

Two triggered barrier systems and several extinguishing agents were tested against coal dust explosion propagating in the main entry of the Bureau of Mines Experimental Mine at Bruceton, Pa. One system used a high-pressure cylinder to propel the extinguishant; the second system used pressurized nitro-gas or Halon 1301 (CF3Br) in a low-pressure system to power the disperser. The relative efficiencies of the extinguishants were determined by compar¬ing calculated concentrations of the extinguishant clouds present in the mine during suppressing of the explosions. Results showed the following trend of increasing effectiveness: Purple-K (KHC03)<water<hybrids consisting of foam or water combined with Halon 1301<Halon alone. On a weight basis, water was two to three times as efficient as Purple-K, whereas the hybrids and Halon alone were only marginally superior to water. Maximum efficiency of an extinguishant is attained by high rates of discharge from the barrier and by minimizing the time interval between onset of discharge and flame arrival to that necessary for discharge. Both the high- and low-pressure barrier systems were demonstrated to be capable of suppressing coal dust explosions; however, because of the potential hazard of the former, the low-pressure system is considered to be the most attractive prototype.

Jan 1, 1979

By David A. Hill

This volume contains a summary of the results of past analyses on U.S. Bureau of Mines Contract No. 80122061 which are relevant to electromagnetic location in mine rescue situations. The analytical results indicated that detection of a trapped miner equipped with a special transmitter is feasible in most situations. Location of the miner by surface measurements is also generally feasible within certain errors. The feasibility of miner detection and the accuracy of miner location have been examined theoretically for a wide variety of situations. Agreement with experimental results is generally good in cases where measurements are available. Personnel involved in the investigation include J.R. Wait (Principal Investigator), D.A. Hill (Co-Principal Investigator), K.P. Spies, A.Q. Howard, and Lana Slusher (Administrative Assistant).

Jan 1, 1974

By Clarence Karr

THE BUREAU OF MINES is investigating methods for upgrading tar produced by the low-temperature carbonization of bituminous coal. This survey was undertaken to compile information needed for identifying the ether constituents of low-temperature tar. Physical properties are listed for 1,024 aromatic ethers. The compounds include cyclic and noncyclic, polyfunctional and monofunctional ethers with oxygen joined directly to either one or two aromatic rings. Alkyl groups up through butyl are included. The compounds are divided into 37 groups ranging in complexity from alkoxybenzenes to dibenzopyrans. Compounds containing aromatic ether groups are important constituents of the neutral oxygen components of low-temperature tar. For example, at Morgantown, W. Va., the Bureau of Mines has identified and determined the amounts of benzofuran, 2-, 3-, 5-, 6-, and 7 -methylbenzofuran, diphenyl ether, dibenzofuran, 2,3-dimethyldibenzofuran, and two other dimethyl-dibenzofurans in the neutral oil from a low-temperature bituminous coal tar (103, 104).3

Jan 1, 1962

This Bureau of Mines report concerns two subjects important in the application of electric power in mining systems. Electrical transients and their suppression are discussed, and several considerations are explored with regard to the use of explosionproof or other electrical enclosures.

Jan 1, 1979

By L. Bruce McDonald

This Federal Bureau of Mines publication is a statistical analysis of all surface and underground coal mine fires reported in the United States from 1950 to 1977. Accounts of selected nonreportable fires and opinion data gathered via interviews with mine safety directors were separately analyzed. Both reported and nonreportable fires were analyzed by time trends, State, ignition source, burning substance, location in mine, equipment, detection, duration, injuries, fatalities, and successful extinguishing agents. It was found that the majority of all mine fires were electrical in origin. The equipment most frequently involved in underground fires was conveyor belts, and in surface fires, it was crushers and/or breakers. Underground fires occurred most often near the working face. Water and hand-portable extinguishers were the most common methods of extinguishment.

Jan 1, 1980

By Joseph L. Condon

Fifteen shots of three explosives with charge weights of 0.52, 1.1, 3.1, and 5.1 kilograms were fired in a pond to study the seismic effects of detonating explosives in water. Shock pressures and bubble periods were measured with pressure transducers in the water. Vibrations were measured on land in three orthogonal directions with particle velocity gages. Statistical tests indicated that a charge weight exponent of 0.43 best scaled the data. While shock pressures and bubble periods showed considerable differences in explosive performances, the amplitudes of ground vibrations showed less difference, and one prediction equation was therefore derived to estimate vibration amplitudes from all the explosives.

Jan 1, 1970

By Milne J. Schmid

A program has been conducted to determine the feasibility of providing a borehole liner for Kelly Bar drilled boreholes in Southern Florida. The concept was to drill the borehole with the Kelly Bar and with it still in the borehole insert a tube which would remain in the unstable ground after withdrawl of the bar. The tube then will provide an unobstructed borehole for the charging of explosives upon completion of the drilling the shot pattern.

Jan 1, 1977

The purpose of this report is to describe the work accomplished by Mine Safety Appliances Company under Contract No. H0110845. This contract required the design, installation and testing of a permissible mine surveillance and communication system for the USBM Bruceton experimental mine facility. While much of the design and operational detail of this system can be drawn from the instruction manuals delivered with the equipment, some of it will be repeated here in Volume I for the sake of clarity, but the principal objective will be to report on overall system and subsystem performance and to suggest design alternatives for future consideration. Details of the overall system design will be found in Volume II of this report.

Jan 1, 1973

By James J. Scott

Eleven workshops were held in various locations throughout the country in an attempt to reach the many diverse groups working in various mineral commodity areas and special ties. These meetings were held between March 1, 1974 and June 25, 1975. They were held under the auspices of the Bureau of Mines Contract to the University of Missouri-Rolla which was designed to help define Bureau research and development priorities. At each workshop a summary of current Bureau research and development was presented and the attendees were asked to present their ideas on what Research and Development programs should be undertaken to meet their needs locally. Participants included representatives of federal and state agencies, educational institutions, mining companies, equipment companies and other interested parties. The workshops covered under this report include lead mining in Missouri, limestone mining, coal mining both surface and underground in the midwest and in the Rocky Mountain area, iron mining in Minnesota, two top management meetings on institutional problems and, finally, a special two-day meeting on roof control.

Jan 1, 1977

By J. O. Merritt

The primary objective of this research program was to recommend ranges of minimum luminance for safety in underground metal and nonmetal mining. Visual tasks critical to safety were identified and rank-ordered. Realistic, full-scale, dynamic task simulations encompassing the most important visual components of the critical tasks were installed in a large simulated workspace. Five trained observers performed the six simulated mining tasks under varying levels of luminance. Over 13,000 measurements of visual task performance were used in developing minimum luminance recommendations for the on-foot underground worker and the mobile equipment operator.

Jan 1, 1983

By Sterling J. Anderson

To define the technical competence and capabilities of a nonexplosive excavation concept, the Bureau of Mines conducted reduced-scale laboratory tests of a mechanical excavation tool called a rock splitter. Hydraulically actuated splitters, capable of generating both radial and axial loads on a predrilled hole, were designed and fabricated. Through paired variable testing and drifting simulation, reduced-scale splitter performance was evaluated in concrete. Testing proved that the rock splitter is capable of excavating within the highly confined drift set-ting and that it offers a distinct advantage over splitters that can generate radial loads only.

Jan 1, 1982

By C. M. McKinney

The Bureau of Mines analyzed 626 crude oils from 546 oilfields in the United States that produced 2,500 BOPD or more during at least 1 of the last 3 years. Included also are crude oil analyses from eight fields that produced less but which were located in areas having few or no fields that produced 2,500 BOPD. The tables show the geographical and geological source, general characteristics. and determined and computed analytical data for each sample. The analyses were made according to the Bureau of Mines routine method and are directly comparable to other previously published analyses.

Jan 1, 1966

By H. M. Lawrence, E. Roca

"INTRODUCTION Of the phosphate rock deposits of the United States that are being exploited actively at present, the land-pebble area in Florida is the largest producer. In recent years the land-pebble district, in Polk and Hillsborough Counties, has produced about 80 per cent of the raw phosphate rock that has supplied the requirements of the several national industries based on this essential commodity.In the land-pebble deposits sizes finer than 16 to 22 mesh are below the commercial limit in phosphate content, and washing-plant practice has been directed to the recovery of the coarser material. Recently, more extensive control of the washery plan has resulted in the saving of additional amounts of phosphate, the loss of which had been considered unavoidable. However, strict requirements of the trade regarding the lowest acceptable grade of phosphate rock prevent the inclusion of more than a very small proportion of the low-grade phosphatic sands with the washery output of phosphate roe:. Further advances in practice resulting in larger recoveries of phosphate can only be effected by the application of processes that are based on other principles than merely a difference of particle size. Research is be conducted actively along these lines by the industry and by cooperating agencies.Flotation has been studied for several years by the International Agricultural Corporation and its allied company, the Phosphate Recovery Corporation. J. T. Burrows, vice-president of the International Agricultural Corporation, in a letter dated July 10, 1929, states:"

Aug 1, 1931

By R. Blickensderfer

Maintaining an adequate supply of minerals and metals to meet national economic and strategic needs is the overall goal of the Bureau of Mines, U.S. Department of the Interior. One method of achieving this goal is to conserve scarce metals by cladding a plentiful base metal, such as iron, with a scarcer metal. To investigate cladding, a vacuum-rolling mill capable of rolling bimetal specimens at temperatures to 1,300° C in a residual gas pressure of 2 x 10-5 torr was established. Metals that were successfully bonded to iron included stainless steels, chromium, nickel, nickel alloys, copper, and several refractory metals including molybdenum and titanium. The effects of the rolling temperature, reduction in thickness, rolling speed, and residual air pressure on bonding strength and bend ductility of the bimetals were determined. Optimum rolling conditions produced bimetals with bond shear strength essentially equal to that of the iron base metal.

Jan 1, 1980

By P. C. McWilliams

Theoreticians in soil mechanics have been pursuing a probabilistic approach to the factor of safety of an embankment or darn for the past 10 years. The motivation for this work is in contrast to the current practice of deterministically computing a factor of safety and treating it as an absolute with no regard to its inherent statistical variability. Basic to the probabilistic approach is the selection of an appropriate statistical model to represent the histogram or probability density function (PDF) of the factor of safety values, Rather than simply assuming which PDF is appropriate, the Bureau of Mines collected data at two waste disposal embankments for consideration, This report addresses three candidate models, using the techniques of nonlinear curve fitting, and identifies the "best" model. A propagation of error formula for estimating the variability of Fellenius? factor of safety is also discussed.

Jan 1, 1983

By James Westfield

A brief résumé follows of some of the most recent activities of the Division of Coal-Mine Inspection that have had a favorable effect. on health, safety, and injuries at coal mines: 1. There were approximately 8,510 active coal mines in the United States during 1955. In all, 82,389 regular Federal inspections of coal mines have been made since Public Law 49 became effective in May 1941; 9,823 of these inspections were made during 1955. 2. The Bureau of Mines introduced the revised Coal-Mine Accident-Prevention Course for Supervisors in the coal-mining industry on March 1, 1948. Since that date, 19,455 supervisors and those aspiring to official positions have completed such training conducted by personnel of the Division of Coal-Mine Inspection.

Jan 1, 1956

By Choon Kooi Quan

Water availability is essential for mining and minerals processing. To provide government and industry with recent data for water use planning and management, the Bureau of Mines canvassed a number of U.S. producers of nonfuel minerals to determine their water use in 1984. Data were analyzed and compared with previously published data in order to examine historical trends in water utilization in the nonfuel minerals industry and to estimate water requirements in the year 2000. Total water use in the domestic nonfuel minerals industry during 1984 was estimated at 2,267 billion gal, of which 571 billion gal was new water and 1,696 billion gal recirculated water. The largest users of water were the phosphate rock, iron ore, copper, sand and gravel, and crushed stone industries, together accounting for almost 90% of total used. More than one-half of all water was used in Florida, Michigan, and Minnesota. In the year 2000, total water use will amount to an estimated 2,679 billion gal, of which 810 billion gal will be new water and 1,869 billion gal recirculated water. Most of this water would be used in producing the foregoing suite of minerals,

Jan 1, 1988

By Galen H. Clevenger, MARTINUS H. CARON

Although there are exceptions, oxidized silver ores containing the higher oxides of manganese are generally refractory to hydrometallurgical methods of treatment. When these ores are of high enough grade they can be smelted; indeed, some rather low-grade ores of this type have been smelted at a profit because of their fluxing value. In the past, when these ores could not be smelted, they either were not treated or were treated at low efficiency, generally by cyanidation. The need for thorough investigation of the problem was therefore evident for some time before the writers began their research. The problem of treating manganese-silver ores seems to have been recognized first about 35 years ago by C. W. Goodale in applying pan amalgamation at Tombstone, Ariz. He attributed the low extraction of silver to the fouling of the mercury by manganese rather than to the presence of a refractory compound of manganese and·silver. Although definite knowledge as to the cause of the poor extraction of silver was lacking, a more or less effective preliminary treatment, that is, a chloridizing roast, was applied. E. M. Hamilton, in 1909, was perhaps the first to define clearly the problem as it affects the cyanidation of silver ores and to suggest possible methods of preliminary treatment. Most of the work done in the interval between the appearance of Hamilton's paper and the assumption of the investigation by the authors was in the nature of routine tests covering suggestions already made rather than of research directed to a fundamental study of the problem. No practical application has so far been made of any of these proposed processes. The investigation described in this bulletin has proved that there s a refractory compound of manganese and silver-probably a manganite- insoluble in cyanide solution and other common solvents for silver. Although this compound has not been isolated from natural ores, it has been made synthetically, and shows all the characteristics of the natural product. Furthermore the authors have shown definitely that heating in air a relatively small amount of a silver compound with a large excess of silica (in the proportions ordinarily occurring in a commercial silver ore) renders

Jan 1, 1925

By D. Randolph Berry

The United States Bureau of Mines (USBM) awarded a contract to Foster-Miller, Inc. to develop guidelines for the storage and use of Self-Contained Self-Rescuers (SCSRs) in underground non-coal mines. An SCSR is a device capable of supplying, in an emergency, one hour of self-contained oxygen (no breathing of mine air). The information and recommendations in this report were developed primarily from three sources: discussions with mine representatives (including management, labor, and government), site visits in underground mines I and a detailed analysis of every reported non-coal accident which produced d hazardous atmosphere during the 5-year period 1976-1980 -plus ten other major incidents from prior years. Volume IV has three major sections: Recommendations and Discussion (Section 2), Analysis of Mine Accidents (Appendix A), and a Summary of Discussions with Mine Representatives (Appendix B).

Jan 1, 1983

By Normal Seidle

This report (rind related Appendices) provides a description of the functional design specifications and related rationale for development of a training system for dragline equipment operators. Phase I activities involved a delineation and detailed analysis of specific behavioral requirements for successful dragline operation. Following the field data collection effort, job/activity/task descriptions were formulated into training requirements which can be achieved by a trainee with training hardware having specific functional capabilities. The training system analysis integrated the training requirements and the trainer functional capabilities into recommendations which configure a total training system. The objective of the training system described in this report is to provide new operators of dragline equipment with the requisite skills and knowledge to assure cost-effective development and an adequate supply of our human resources.

Jan 1, 1975