Search Documents

By R. Singh, M. Roy, D. Singh

Success of a blasting pattern in Blasting-off-the-solid (BOS) in Bord (Room) & Pillar method of coal mining is judged by the percentage of pull achieved vis-à-vis the yield of coal produced in a blasted round. Improper blast design and distribution of explosives in shot holes normally causes poor breakage i.e. a major portion of shot holes left unbroken resulting into reduced yield per blast. Over and above the disturbance to the roof is also due to excessive vibration caused by explosive energy not properly utilized in fragmentation.

Jan 1, 2003

By L. Trivino

Blast-induced damage criterion based on the peak particle velocity has worked reasonably well for estimating building damage. However, the same criterion cannot be used to estimate damage to rock and mine structures such as shaft and tunnel walls. It does not take into account the nature of seismic radiation pattern in the near-field, which is very different than what is obtained at far-off distances. To investigate this phenomenon, a systematic study has been carried out involving single-hole blasts and normal production blasts, with explosive source ranging from nearly point source charges to standard borehole sizes (6-7 m long explosive column), with charge weight varying from 0.5 kg to 30 kg. In the near-field, it is shown that, both P-wave and S-wave take a dominant position compared to the mainly surface waves measured in the far-field. These are shown to depend strongly not only on the length of the explosive column but also the way it is initiated in the borehole (i.e. direct vs. reverse initiation in the borehole) with respect to the target location. The seismic radiation patterns were recorded by high-frequency triaxial accelerometer stations grouted in the rock mass. This study describes the nature of seismic radiation in the near-field from long and short charges, the role of initiation direction and their effect on frequency with respect to sensor locations or target area of interest, and their implication in prediction of blast-induced damage in the near field.

Jan 1, 2009

By Martti Hagfors

UNDERWATER EXPLOSIONS - Part 6 - EFFCTS OF CYLINDERICAL SHAPE OF CHARGE TO THE RESULTS OF ENERGY MEASUREMENTS OF EXPLOSIVES

Jan 1, 2008

By Thomas Leonard, Philip R. Berger, Bryan E. Papillon

Bardon Trimount Inc., a large producer of aggregate, crushed stone, and concrete, was experiencing significant public opposition to its five quarries in the Boston area. It was believed by the authors that this opposition could be significantly lessened if the total number of blasts per week were reduced. Although the blasting company at these quarries, Austin Powder Company, contended that this could easily and safely be accomplished by increasing the size of the blasts, regulations precluded this alternative by limiting the total amount of explosives that could be used per blast.

Jan 1, 1996

By Richard Brummer, John Hadjigeorgiou, Patrick Andrieux

Some of the major challenges associated with underground mining at depth and/or under high extraction ratios are related to the resulting high stress levels, which can lead to the failure and collapse of the rock mass surrounding the excavations. Sudden and violent failures, which can have severe consequences, represent the highest degree of difficulty in terms of underground personnel exposure, erratic and unpredictable production, ground rehabilitation requirements, possible reserve losses and overall mining costs.

Jan 1, 2012

By David G. Borg

Emulsions explosives, like slurries or water gels, are water based explosives. Emulsions were first introduced as a packaged blasting agent in the late sixties. Since then, many new variations have been developed, from small diameter detonator sensitive products to bulk loaded anfo/emulsion blends. Explosive detonation characteristics such as velocity of detonation, density/sensitivity relationship, strength, and water resistance along with how they relate to the type of rock and type of application will be presented. Various methods of sensitizing such as glass microspheres and chemical gassing along with product limitations and safety recommendations for bulk loading emulsions will also be presented.

Jan 1, 1994

By Stuart Brashear, Lee Schettler

The effect of water on several ANFO/emulsion blend ratios are documented by both physical observations and analytical testing to demonstrate the effect even small quantities of water can have on water resistant blends.

Jan 1, 1996

By H. Rossmanith

This contribution introduces the fundamental concepts of wave propagation and fracture mechanics which form the basis of electronic blasting, i.e. precise initiation timing using electronic detonators. The concept of Lagrange diagrams will be frequently used for the calculation of the delay time between blast-holes in a row and rows of blast-holes. The effect of burden and structural geology will be briefly touched. It is found that the advanced blasting technology based on the use of electronic detonators introduces a change of paradigm. It will be shown that knowledge in wave propagation and fracture mechanics is essential for the successful application of the new blasting technique in industry. In particular, the delay time, the wave speeds in the rock mass, the shape of the wave pulse and the acoustic impedance mismatch have become decisive parameters in advanced blasting. Utilizing the wave speed and wave shapes of detonations, large scale tests Utilizing the wave speed and wave shapes of detonations, large scale tests in various countries (Australia, Chile, etc.) have shown that optimal delay timing requires shorter delay times in conjunction with allowing for a wider drilling pattern and the use of a reduced amount of explosives, i.e. a lower powder factor. This seemingly contradictory arrangement is fully justified by using scientific principles in blasting, and converting blasting from an art to a scientific discipline.

Jan 1, 2003

By Michael F. Barber

"Highway slopes are intended to remain stable over a long period of time. Unexpected slope failures can be costly in terms of human life and property damage or loss. Cleanup of failures can prove to beextremely expensive."

Jan 1, 1999

By A. Karadogan, G. Tuncer, A. Kahriman, S. Gorgun

This paper presents the results of ground vibration measurements induced by blasting operations at five different sites located close to the residential areas. Within the scope of this study, ground vibration components were measured for all blast events over a long period of time in order to predict peak particle velocity and determine the slope of the attenuation curve for five sites. During the study, while the parameters of scaled distance were being recorded carefully, suitable monitors for all blast events of five blasting sites measured the ground vibration components. At the end of evaluation of the data pairs, an empirical relation, which gives an average line at 95% confidence level, and upper bound 95% prediction line with a good correlation coefficient was established and suggested for each site

Jan 1, 2003

By Mark Svinkin

The purpose of this paper is to present an overview of recommended existing criteria of ground vibrations generated by blasting. It is shown that these criteria have limited liability because they were found for specific categories of structures. A new approach based on measurement of structure vibrations is suggested for assessment of damage in structures subjected to blasting vibrations. This approach provides the flexibility of implicitly considering a variety of soil-structure interaction and structure conditions. It is explained a new frequency-independent safe-level criterion of 51 mm/s (2 in/s) for the PPV of structural vibrations. Attention is brought to use seismographs properly calibrated for the required frequency range. Positive flexibility is demonstrated in assessment of structure and component of concern vibrations from blasting.

Jan 1, 2003

By X Meng, W. A. Hustrulid, M. K. McCarter

Rock excavation in both surface and underground mining is largely accomplished using the drill and blast technique. At the perimeter of such excavations, cautious blasting procedures are often employed to minimize unwanted damage to the remaining rock. Of the several different techniques available, the use of explosive charges with a diameter smaller than the holes in which they are introduced (so-called decoupled charges) is the most common. In spite of the long and widespread use of the technique, a technically sound basis for relating the borehole wall pressure to the explosion pressure is still lacking. Such a relationship is required for optimal design

Jan 1, 2005

I was lucky to land a job in the powder business. I was looking for some way to support my wife and first child to be when I saw an ad in the Hercules magazine, “Explosives Engineer” for technical representatives. I answered the ad in hopes that a geologist might find something else to do besides sit oil wells or “doodlebug” for oil. Both of these occupations I had tried and while the money was good the life was a bit erratic. The Army also wasn’t made for a guy who asked too many questions although my two plus years in uniform were interesting and in a few cases fun.

Jan 1, 2004

By John W. Gunnett

The purpose of this afternoon’s presentation is to highlight the investigative proce dures employed to complete an engineering audit of a mining operation. Skelly and Loy has been retained to perform operational audits throughout the nation’s coal fields, The need for such studies is generally associated with long term coal supply contracts and is typically initiated by the utility company. However, a number of projects have been commissioned by mining companies while others have been jointly funded by the utility and mining company.

Jan 1, 1992

By Harry Verakis, Thomas Lobb

In the past decade, approximately 5 billion pounds of explosives were used annually in the United States. Most of this quantity of explosives was used by the mining industry and coal mining was the dominant application for explosives. Considering the large amount of explosives used, the accident safety record for the mining industry has improved significantly over the past two decades. Blasting accidents are usually a small percentage of the total number of mining accidents. However, blasting accidents continue to occur and the severity of these accidents is disproportionately high with respect to other types of mining accidents. This paper is a summary and an update of the surface mine blasting accident investigations and studies conducted previously by the Mine Safety and Health Administration (MSHA) and the former U.S. Bureau of Mines.

Jan 1, 2001

By Felix Torres

CVRD is one of the largest mining companies in the world. Adoption of new technology and improving operational efficiency are top company priorities. Initiatives in these areas have driven continuous company growth and an increased share price. During the first half of 2001, the company had a net profit of nearly US$ 500 M.

Jan 1, 2003

By Roger Holmberg, Donald Jonson

The Swedish Standard SS 460 48 66, “Vibration and shock - guidance levels for blasting induced vibration limits”, is based on more than 50 years of experience from blasting close to structures and tunnels. The Swedish Standard gives a method for calculation of guidance values for different types of buildings and ground condition under the building. This is done for every building and structure within a predetermined zone. The guidance levels are for the peak particle velocity monitored in vertical direction. The standard is valid for all kinds of blasting project (tunnelling, quarrying, mining etc.) The guidance levels neither take in to consideration discomfort for people inside the building or structure nor vibration sensitive equipment inside the structure. The paper also presents the Swedish Standard SS 02521 “Vibration and shock - Blast induced airborne shock wave - Guidance levels for buildings”.

Jan 1, 2005

By Billy J. Thorne

The damage model in PRONTO simulates the dynamic fracture behavior of brittle rock. It is based on work started by Kipp and Grady, [lg] continued by Taylor, Chcn and Kuszmaul [I91 [20] and recently.modified by B. J. Thorne (first documented here). The essential feature of this model is the treatment of the dynamic fracture process in rock as a continuous accrual of damage in tension, where the damage mechanism is attributed to microcracking in the rock medium. The fundamental assumption of the damage model is that the material is permeated by an array of randomly distributed microcracks which grow and interact with one another under tensile loading.

Jan 1, 1989

By David P. Reddick

Economics is a social science dealing with the allocation of scarce resources. In modern times the “science” was identified by Adam Smith in his book, The Wealth of Nations, written in 1776. Mr.Smith, highly influenced by the Mercantilists of the 17th and 18th centuries, identified the “Invisible Hand” which would lead every individual to pursue selfish rewards in purchasing goods. He speculated these selfish motives would result in the best good for all. Price would be determined by barter, at a point where self-centered customers and vendors were mutually satisfied. Today, Smith’s theory is known throughout the world as “Capitalism” but most often termed “Free Enterprise” in the United States.

Jan 1, 1992

By W B. Gregg

The rock blasting and mining industries use a system of detonators and explosives for mining operations. Many detonators use small metal bridgewires, which are heated by passing a current through the wire, heating and igniting the pyrotechnic powder in contact with the wire. Typical bridgewires require a current of at least 3 amps, applied for a few milliseconds, for an explosive output. The semiconductor bridge (SCB), in comparison, initiates an explosive in 0.01 to 0.1 of a millisecond.

Jan 1, 1994