Search Documents

By Peter Moser, Mark Ganster, Andreas Gaich

Surveying of a bench face before blasting is a pre-requisite for a proper blast planning and for a satisfying blasting result both in terms of safety and fragmentation. When surveying a bench face, preferably a large amount of measurement points are required in order to determine the geometry and especially the irregularities with sufficient accuracy. Only contact-free measuring systems allow evenly distributed measurements over the whole bench surface. Existing systems such as total station, laser profiler, or laser scanner show significant drawbacks such as that surveying results are just isolated values of the bench geometry such as heights or profiles, that borehole positions have to be defined in advance in order to know where to take profile measurements and that systems require special surveying skills and that they are expensive too. In order to overcome these difficulties and to provide the blasters a simple tool for bench surveying, blast design and layout and the subsequent back-transfer of the blast plan into the quarry, the Department of Mineral Resources& Petroleum Engineering of the University of Leoben, 3G Software & Measurement company and Mineral AB, one of the largest producers of aggregates in Europe formed a joint venture to develop a new system. Based on an existing stereophotogrammetric system for rock surface surveying and joint analysis (JointMetrix), a new tool was developed within a year. Apart from several mines and quarries using that new tool already today in the daily work, both the Department of Mineral Resources& Petroleum Engineering at the University of Leoben and Austin Powder GmbH Blasting Service did a lot of studies to determine the reliability of the new stereophotogrammetric blast surveying and planning system and its precision in comparison to classical laser surveying equipment. After 1 year of testing and comparison with laser based surveying instruments, it can be concluded, that the new technology of blast surveying& design systems based on stereophotogrammetry is suitable for being used in the daily work routine in quarries and mines. The comparison of the precision of laser based systems and stereophotogrammetric systems has shown, that the deviation between these two types of systems is less than 10 cm, in many cases even lower.

Jan 1, 2007

By Steven A. Mathe, Seokbin Lim

Current analytical models can accurately predict the final velocity of explosively driven flyers and can somewhat predict the acceleration profile, but do little to address the deformation of the flyers. Explosive systems such as linear shaped charges and explosively formed projectiles, which can be described as multiple interacting explosively driven flyers, often involve interactions between the flyers that occur much before the flyers reach their predicted final velocity. In this regime, it is important to accurately understand both the acceleration profile and the deformation profile of the flyers, as both significantly affect the functioning of the explosive systems. Previous work proposed an analytical model to meet this need. As the expanding gas cloud of detonation products drives the flyers, rarefactions impinge upon the gas cloud from around the flyer edges, which produces a pressure difference across the back face of the flyer leading to deformation of the flyer. Previous research condensed the effects of the rarefactions into a single term, the pressure release ratio, ?, which was calculated based on hydrocode simulations of a block of explosive only and an assumption of isentropic expansion. This work intends to determine the value of ? for different explosive compounds. The results of this analysis were compared to hydrocode simulations of an open-faced sandwich configuration explosive/flyer system with an average accuracy of 15% across the tested compounds.

Jan 1, 2015

By Doug Bartley, Roy McKinstry, John Floyd

In March of 2001, Barrick Goldstrike became the first surface gold operation in North America to evaluate the advantages of electronic detonators. A detailed study was conducted to quantify the benefits of the use of electronic detonators to the downstream excavation, crushing and ore processing operations. The following methods were used to quantify blast performance:

Jan 1, 2003

By Jackson R. Pressley, Bruce Vandenberg

An explosive’s velocity of detonation, (VOD), can be used to indicate a number of important characteristics regarding the product’s performance, under specific field and test conditions.

Jan 1, 1997

By Bruce Vandenberg

A 3D, PC based computer program is currently under development by Blasting Analysis International, Inc., to analyze the kinetics of full scale blasts with two or more high-speed motion picture cameras.

Jan 1, 1990

By Jason Ryan, Stephen Harria

Q.E.D. (QED) is a blast design and evaluation model that allows full three-dimensional design specification including the development of unique “live” terrains and an unlimited variety of complex charge configurations. QED’s analysis package allows the examination of likely outcomes resulting from changing various design variables in terms of vibration, fragmentation, rock-mass damage and muck-pile profile. Especially applicable to use cautious blasting applications, QED’s damage model uses vibration to estimate rock damage beyond excavation boundaries. This relates directly to operations such as Yucca Mountain Nuclear Waste Repository in Nevada, where damage beyond the excavation perimeter must be tightly controlled. The U.S. Department of Energy (DOE) h as b een studying a site at Yucca Mountain, NV to determine its suitability for long term storage of nuclear waste. The main mechanism of waste isolation will be the natural barrier of the host rock Total Systems Performance Assessment (ISPA) is used to model the excavation design and its behavior over time. Of importance to TSPA is quantifying the condition of the rock-mass before and after excavation. Ideally, there should be no excavation-induced changes to the rock-mass’ structure (removing the requirement to model the effects). At the least it may be possible to keep excavation-induced damage far enough away from waste packages so that modeling of these effects will not be required. QED can calculate a prediction of the extents of blast induced damage to the rock-mass. By using this metric as a design parameter, it may be possible to complete excavation of the repository more rapidly and inexpensively than previously thought, without jeopardizing the structural integrity of the waste containment areas or requiring blast damage to be modeled by the TSPA. This paper will explain the structure of the QED blast modeling system and show the analysis of historical data from Yucca Mountain. Processing of the historical data and the subsequent results will demonstrate how blast modeling can be used on an ongoing basis to assist the excavation process at Yucca Mountain.

Jan 1, 2000

By Michael Mann, Kenneth K. Eltschlager

The International Society of Explosives Engineers (ISEE) Standards Committee has recently updated both the Field Practice Guidelines for Blasting Seismographs and the Performance Specifications for Blasting Seismographs. The revisions are the result of public and industry input along with recommendations of the ISEE Blast Vibration and Seismograph Section. The committee is comprised of blasting seismograph manufacturers, users and general interest personnel. On an as needed basis, subject matter experts are enlisted to advise the committee. Three phases of activities are necessary for each revision cycle: request for comment on the existing standard, first draft revision of the standard based on public input, and final draft approval by the ISEE Board of Directors. The ISEE standards revision process will be explained and each standard will be discussed along with the significant revisions from the latest revision cycle.

Jan 1, 2018

By Unknown

More than 60 years ago Lakota (Sioux) Chief Henry Standing Bear asked Korczak Ziolkowski to create a monument of Crazy Horse in the sacred Black Hills. Today, you can see Standing Bear’s dream has grown into enormous reality. Crazy Horse Memorial, mankind’s largest mountain carving in progress, is being carved in the round and when completed will be 641 feet long and 563 feet high. Crazy Horse is only 17 miles from Mount Rushmore National Memorial, giving South Dakota unique boasting rights for having two extraordinary mountain carvings in such close proximity

Jan 1, 2009

By Brian Wingfield, Greg Williams, Richard W. Givens

Application of required energies into the rig design can have a dramatic impact upon productivity. Computer modeling of these production variables has led to changes in design with values closely approaching actual field data. Knowledge of these required energies can also specify the proper drilling technique to the application. With this knowledge, productivity-to-cost ratios can be determined with the most efficient option chosen.

Jan 1, 1995

By Dennis R. Jr Bell

Before beginning any site development or mineral extraction activity, it has been well documented that it is first prudent to gain an understanding of the prevailing geologic conditions.Whether it’s identifying the depth to type of bedrock, or determining the quality and quantity of the in place mineral deposit, these factors should always be considered in a project’s fatal flaw analysis. In situations where there is limited subsurface information, geologic models have been proven to be one of the most valuable and cost-effective tools used by the developer and/or his consultant.

Jan 1, 1997

By Lifeng Li, Jhon Silva-Castro

In a previous work, the authors analyzed the overlapping probability of two adjacent charges in a single hole for pyrotechnic and electronic detonators. This document extends such work to a complete mine blast where more than two holes are detonated. In a mine blast, all the blast holes are connected as a network by detonators to follow a given initiation sequence. Such initiation sequence’s performance is based on the adequate timing between charges in the mine blast. The analysis of the reliability of a mine blast based on the timing between charges and the initiation type is presented in this document. For a long-run time and under proposed operating conditions, the reliability of the mine blast can be analyzed based on the network which is treated as a system. The failure of the system is defined as no success between any two delays charges either in a single hole or in between two holes.

Jan 1, 2016

By Randal Martin

Recently, questions regarding the influence of atmospheric temperature and humidity levels on airblast levels have arisen at a number of blast sites. Humidity is alleged to have contributed to high levels of disturbance within communities surrounding blasting. In some cases, local regulatory agencies considered adopting guidelines to specify humidity and temperature ranges under which blasting cannot take place. However, it is normal blasting industry practice not to consider humidity or temperature effects, in the absence of inversions, on airblast levels. When blasting is conducted in the vicinity of residential structures, the influence of weather on the propagation and attenuation of airborne noise from the blasting site is always a concern. Sound naturally attenuates in air with distance from the source. A part of this attenuation is attributed to divergence at the airblast wave front, while the remainder of the attenuation is an accumulation of various factors that include temperature and barometric pressure, absorption in air due precipitation and vegetation, wind and temperature gradients, atmospheric turbulence and topography (Beranek, 1971). Wind speed and wind direction, as well as vertical and horizontal temperature gradients can cause airblasts to focus in local regions surrounding blasting operations and may result in air pressures greater than expected. In fact, wind and temperature inversions can actually increase sound levels with distance from the blast site. Close to the blast site, the effects of inversions may be negligible but may exceed 10 dB at 800 m or greater (Davis and Cornwell, 1991).

Jan 1, 2001

By William H. Highlands

Lightning is a natural phenomenon which poses a potential hazard to people, structures, and equipment unless adequate protection is provided. The type of protection required is related to the nature and of the facility. The decision making process involves a number of interrelated factors which should be considered when determining the need for protection.

Jan 1, 1989

By Zach Ellis, Dusty Fisher

Lightning is a major concern in the explosives industry. The enormous amount of energy delivered to the Earth from a single bolt of lightning is more than capable of detonating explosives. Although explosives incidents caused by lightning strikes are rare, lightning is of great concern to blasting professionals who spend many hours working on or near loaded blast patterns.

Jan 1, 2015

While ring-blasting techniques offer substantial benefits, there are intrinsic problems that are exacerbated when large blocks of ore are mined in attempts to improve the production economics. These problems relate to both the convergence of holes around the ring drive and the charging of up-holes. The size and shape of the ore block concerned should be carefully considered so that good drilling, patterns can be achieved. The hole diameters chosen, both affect and are affected by the size of the ore block. The explosive selected depends on the hole diameter and together with the diameter, determines the nominal drilling pattern. Ring-drilling patterns are best derived through the use of computer software together with engineering judgement. The loading of explosive is necessarily high, and charging patterns require careful thought if overcharging is to he minimised and adequate energy is to be available at all parts of the ore block. Initiation systems are critical to the blasting results, but sub-optimal systems must be adopted if collar priming is practised. In view of all these factors, idealised guidelines can be given for ring design, but it should be recognised that developments in technology may in time change some of these parameters.

Jan 1, 2000

By Zach Ellis, Dusty Fisher

The Office of Surface Mining, Reclamation, and Enforcement (OSM) cited a large surface coal mine for a series of flyrock incidents that occurred when blasting close to the mining lease perimeter. The OSM placed the company on a pattern of violation status. It was determined through analysis of blasting practices that flyrock could be controlled at the mine by drilling a smaller diameter hole and stemming with crushed rock when blasting within 1,000’ (304 m) of the lease line. The procedure to install and remove the small diameter drill steel was cumbersome and dangerous because it was a manual transition. The drill carousel could only hold one diameter at the time the project was initiated. The process was very time consuming, involving a mechanic to transport the steel to the drill and spend up to 1.5 hours of downtime switching the steel. In addition, the hydraulically operated break-out wrench and break-out fork on the SKS Infinity Redrill® is only designed to work with one diameter, so these tools could not be used to disconnect subs and steels on the string. At the time, the mine’s breakdown was between 30-40% small diameter (6 ¾” (171 mm)) versus large diameter drilling (10 5/8” (270 mm)). The drill and blast group was challenged with the task to implement a 6s (Six Sigma) project that would reduce the amount of time spent on steel change-outs on the rotary drills while improving the safety of the task. A solution was proposed to carry the small diameter drill pipe, lower small diameter sub, and small diameter bit on board the drill at all times. The goal of the project was to carry the steel in the carousel after modification so that the driller could change the diameter himself on board the drill in less than 45 minutes without any assistance from a mechanic. The drill had to be modified so that the hydraulic operated break out wrench and deck fork could be utilized on both diameters. The drill accessory supplier and the mine worked together to design and implement design changes and new equipment onto two rotary drills, and new standard operating procedures (SOPs) were created for the new process. The project has been in the sustaining phase for approximately three months now and all steel diameter changes are completed by the operator under the allowable time limit.

Jan 1, 2015

By John Babcock, Bryan C. Smith

In a partnership between Luck Stone Corporation and Loudoun Water, a 42” (1.067m) steel pipeline was constructed along the perimeter of an extensive permitted reserve of diabase rock Luck Stone was about to begin mining. Loudoun Water provides drinking water and wastewater services to over 75,000 households in Loudoun County, Virginia. In discussions to establish the 30-foot (9.1 meter) easement for Loudoun Water within the permitted reserve of diabase rock, Luck Stone and Loudoun Water agreed on the following basic conditions: • Luck Stone could execute production blasting as close to the easement as physical conditions of overburden depth permits. We estimated the minimum distance to be about 75-feet (22.86 meters) from the centerline of the pipe. • Loudoun Water would install strain gauges on the pipe every 500-feet (152.4 m) along the entire length of the future reserve area. This resulted in the installation of 18 strain gauges. • Luck Stone would contract a third-party vibration monitoring company, agreed to by Loudoun Water, to monitor the strain gauges and provide seismograph reading at appropriate locations along the pipe as mining progresses. All information would be provided to Loudoun Water. • Luck Stone’s blasting will be conducted in a manner that ensures the recommended strains are not exceeded.

Jan 1, 2019

By Joseph Nawrocki, Margaret Hettinger, Dr. Catherine Johnson

"Optimized rock fragmentation is essential for minimizing downstream costs to mining operations.Photographic fragmentation analysis, vibration monitoring, and high-speed video all providemeasurements of blast effectiveness and supply data that allows operations to modify blasts to achieve downstream goals."

Jan 1, 2016

By Brian Carr

This workshop will display all of the existing products that are available as stemplug devices and discuss the general concept of the use of them. Actual results will be discussed along with several case histories. There will be adequate time for questions and answers.

Jan 1, 2000

By Dale Preece

A carefully designed and controlled in-place destruction experiment was performed on a concrete bunker buried in 4.27 m (14 ft.) of soil. The objective was to determine if the explosive charges would collapse the structure in-place without requiring mechanical excavation. Collapse of the buried structure was first attempted by drilling holes in the soil and placing four 13.38 Kg (29.5 lb) Comp B explosive charges at a depth of 2.13 m (6.7 ft.). The configuration of the charges when detonated was 2.13 m (6.7 ft.) off the top of the concrete roof and 3.66 m (12 ft.) apart in a square pattern. Detonation of these charges created a crater ~4.88 m (16 ft.) in diameter and 2.13 m (6.7 ft.) deep, leaving ~2.13 m (6.7 ft.) of soil covering. Very limited spalling occurred on the ceiling of the concrete structure as a result of detonating these four charges. The second attempt to collapse the structure consisted of placing another single 13.38 Kg (29.5 lb) charge, identical to the first four, near the geometrical center of the bunker roof. This charge was detonated in the soil cover 100 to 200 mm (4 to 8 in.) above the reinforced concrete roof, collapsing it. Due to the collapsed roof and remaining soil cover, the structure had been collapsed in place, requiring no further demolition.

Jan 1, 2006