Search Documents

By P. Tittes, M. Deal, M. Spicher, S. McDaniel, J. Wickens

"Haile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The relatively low grade and refractory nature of the deposit has been a challenge for efficient processing since the start of mining on the property. Early processing techniques included gravity separation and barrel chlorination. The last operation employed heap leaching in 1985 through 1992. After being closed and reclaimed for over 20 years, the property is poised to re-open and produce once again. In this chapter of the Mine’s legacy, flotation and ultra-fine grinding will be employed to achieve economic extraction of gold and silver from the pyrite. This paper briefly reviews some of the mine’s history, the metallurgical testing, the flowsheet and discusses design considerations.INTRODUCTIONHaile Gold Mine is located near Kershaw, South Carolina, approximately 50 miles south of Charlotte, North Carolina. Gold was first discovered at the site in 1827, and the property has been through several operating periods since. The last operation employed heap leaching in 1985 through 1992. Since then, the property has been closed and fully reclaimed. Romarco Minerals acquired the property in 2007, and began an exploration program that has delineated over 62 tonnes (+2M ozs.) of gold in reserve at an overall grade of 2 ppm (0.06 opt). This paper provides a brief history of the property, a summary of metallurgical testing, description of the process flowsheet and discusses design considerations.HISTORY1827 – 1837Gold was discovered in creek beds on the Haile property in 1827. The property was owned by Benjamin Haile, and the first few years of production came from placer mining. After gold was discovered in schist beds to the sides of the streams, Haile expanded the operation by leasing 18 meter-square (50 ft.) plots to local planters. These planters used slaves to work the small excavations in the agricultural offseason. The gold ore was taken to arrastras where the free gold was liberated and recovered. The excavations were above the water table, generally less than 18 meters (60 ft.) down, and it was noted then that gold could be found embedded in sulfides and difficult to extract."

Jan 1, 2013

By Cameron J. Clayton

Cumberland Resources Ltd. is currently planning to develop the Meadowbank Gold Project located some 70 km north of Baker Lake, Nunavut in the eastern Canadian Arctic region. The Meadowbank Gold Project currently consists of up to 6 main gold bearing deposits within relatively close proximity to one another which are planned to be mined primarily as a truck-and-shovel open pit operation and using conventional gold milling and extraction. The mining plan indicates that approximately 20 million tonnes of ore will be mined over a mine life of 8 to 10 years. The operation will generate approximately 160 million tonnes of mine waste rock and about 20 million tonnes of tailings. The site is located in an area of continuous permafrost with mean annual average air temperature of -11 °C and average annual precipitation in the range of 100 to 200 mm. Lakes cover a large portion of the site, including some of the ore deposits. The location of the site, and the physical environment, pose challenges to development. This paper presents some of the designs considered to effectively manage and utilize the waste products of mining at the project.

May 1, 2004

By Karla Kaboth, Brad Garraway

"The surface of many concentrate thickeners has traditionally looked like that of a flotation cell. Over the last three years Normandy Golden Grove Concentrator, in partnership with Outokumpu Technology have developed and implemented an innovative breakthrough deaeration technology to address this problem.When installed in the thickener feedline, the system successfully detached air bubbles adhering to the solid particles and removed air bubbles from the feed stream, subsequently presenting a fully deaerated feed to the thickener feedwell.Tests to date have shown an 80% reduction in overflow solids. As a result, costs associated with concentrate loss and measures to recover concentrate that settles in process tanks and ponds have been minimized.MOTIVATIONIt is recognised in mineral processing operations that the entrainment of finely divided air in thickener feeds can cause significant problems in the operation of a thickener. This is particularly the case with thickening of flotation concentrates, in which air bubbles are strongly attached to the mineral particles and are difficult to remove. Such particles attached to fine air bubbles rise to the thickener surface, and hence over the weir and into the thickener overflow. High solids carryover can lead to a direct loss of mineral product, and if the product settles in process water tanks and ponds, the recovery of this product by means of intermittent dredging operations is usually expensive and inconvenient.Many concentrate thickeners are fitted with devices which attempt to alleviate this problem. Froth rings or baffles, skimmers and froth sprays, all play a part in reducing the amount of solids carried over into the overflow. However, many froths are very stable and persist despite these measures. In the worst cases, a thick froth layer forms which builds up to a depth greater than the froth ring, and hence may overflow or pass beneath the ring . Any concentrate that finds its way past the froth ring can also cause blockage of the overflow weir and launder, and has the potential to upset clarification performance by cutting off sections of the overflow handling system. The formation of a froth layer on the thickener also makes it more difficult for the operator to monitor the clarification performance."

Jan 1, 2001

By Kjell Winther

"Hydralift Scanmec introduced early in the eighties a new and different mill design for very large grinding mills. The design described has actually no size limitation upwards and is so far suggested with motor power up to 40 MW. The mill is furnished with gearless ring motor drive transmission. It is totally fabricated, without heavy castings. The first installation, an 8, 1 MW ball mill dia. 6,5 m x 9,65 m length, has been in continous operation in 13 years without problems. Total grinding costs has been reduced with 3 0% compared to traditional smaller mills. Reductions has been achieved in maintenance cost, power consumption, liner wear and grinding media consumption.So far 3 ball mills of the described design are delivered and in operation, one grinding Iron ore and two grinding Nickel ore.IntroductionThe design of mills for mineral ore dressing has basically been unchanged since grinding in mills started some I 00 years ago, in spite of the fact that mills have grown larger and larger. This has resulted in structural and mechanical problems, causing expensive failures and loss of production.Hydralift Scanmec engineers were designing mills for more than 20 years according to the old «rules». As they experienced interest for an increase in the mill size at the time when reports about failing mills were published, they started analyzing the different mill parts to find new solutions. One goal was to only use elements from proven technology in the new design. Two key items were ring motor (wrap around motor)(Isch et al. 1977, Meintrup and Klein 1982, Ranze 1983) and large diameter pad bearings (wrap around bearings)(Fuller 1984), both acknowledged from other industries."

Jan 1, 1995

By M. Sturzenegger

This paper documents a field survey using long-range terrestrial digital photogrammetry at the Palabora open-pit mine, South Africa, for multi-scale characterization of rock mass discontinuities. Stereomodels covering the entire mine were generated based on photographs taken from a distance of 1600m across the pit, using a series of f=20-400mm lenses. Details on the methodology used and its accuracy are discussed. Preliminary results on discontinuity orientation, persistence and intensity are presented, highlighting the effect of observation scale. The potential uses of long-range terrestrial digital photogrammetry in open-pit mine and large natural rock slope environments is emphasized. The use of an f=400mm lens from distances larger than 1.5km may represent an important step forward in the geotechnical characterization of inaccessible remote rock faces.

May 1, 2009

By A. Vien, B. C. Flintoff, R. P. Edwards

"This paper provides a critical review of the development and application of advanced controls in mineral processing at the industrial level. These algorithms can be sub-divided into four broad categories: Kalman filter, self-tuning, extended horizon, and knowledge based or expert systems. Applications from each category are described outlining the benefits derived, the relative advantages of that particular controller, and potential limitations of the controller which may inhibit their more widespread application. The paper will conclude with a description of control algorithms which are currently in the rudimentary design stage, but may hold tremendous potential for mineral processing control systems in the next decade. INTRODUCTIONThe Canadian mining industry has a large installed milling base and many plants are run with manual or low level automatic process control. The competitive pressures imposed by the market will not allow these operations to ignore the significant increase in efficiency that can be achieved through the effective application of advanced process control. These improvements will come in the form of better quality, higher productivity and reduced costs.There have been quite a number of reports of successful applications of advanced control in mineral processing applications. As this trend continues, and more of the work is documented, the technology will be more effectively transferred to process and control engineers. It is the authors' opinion that the most difficult problems facing process control are not really technical in nature. Rather, they lie more in process control education. This extends from management, through engineering to the operators.The purpose of this paper is to provide a tutorial type overview of some of the more frequently encountered advanced control algorithms. The assumption is that the reader has a superficial knowledge of this technology. In the discussions which follow, several techniques are explored within the framework of simple process examples. Industrial examples are cited for each and an evaluation of the expected longer term potential is given."

Jan 1, 1992

By Stephen Hammond

?Our own prejudices form the greatest barrier to creating an inclusive working environment.? Have you witnessed? Racism or Negative Comments about an Aboriginal Person? ?You are free to compete with all the others?, and still justly believe that you have been completely fair.? Lyndon B. Johnson

May 1, 2008

By Bill Mercer

The Triggers for PDAC Involvement in H&S ??Increase in serious accidents in mineral exploration in past few years ??Increasing junior role in exploration ?? Impression that there were few H&S protocols in place in smaller companies ??Lack of national benchmarking ?? The attitude that H&S is a provincial responsibility ??Corporate Social Responsibility initiative What is the issue in exploration? ??Mining?s reputation as ?dirty and dangerous? ??In public?s and media?s minds exploration employees are ?miners? ??In Canada, regulators often do not distinguish between ?exploration? and ?mining?. ??How does exploration compare to mining from a H&S point of view?

May 1, 2008

By Tatiana Ravani von Ow, Leandro Bomvisinho

"The size of mills driven by ring-gear or by a gearless solution has significantly increased in the last years. This has created additional challenges for the driven equipment. The requirements for the mechanical devices and the power grid have become more demanding. Controlled soft starting and operation, especially in dual pinion mills, as well as the protection of the equipment has gained importance. The selection of the drive solution for the mill therefore becomes more critical. Besides the classical criteria such as performance, efficiency and capital costs other factors come in the evaluation of the system such as flexibility and optimization of operation, reliability and the ageing of the grinding equipment.Variable speed solutions offer significant advantages over conventional fixed speed drives due to their application specific features and process optimization capabilities, even for ball mills where these are not seen yet as a must.The initial capital costs are higher than some of the direct on-line solutions however the benefits for the operation during the lifetime of the mill generated by the use of converter solutions justify the additional higher investment.INTRODUCTIONThe method of powering mills such as AG, SAG and Ball has a long and technically interesting history. It can be said; almost every decade in the last half century had its own trend. The trend was dominated by the market demand, by the process development and requirement of the mechanical and the electrical technology but mostly by the price of the applied technology.All has started about 50 years ago with mill diameters less than 20 feet driven by fix speed synchronous or wound rotor motors with the power of about 2 MW. Around 10 years later, the mill sizes increased, but the necessary torque could not be transmitted by one pinion therefore dual pinion solutions were developed to power the mills. However, realization of the dual pinion solution was only possible when load could be evenly shared between the two pinions."

Jan 1, 2010

By D. Getzlaf

"Oilfield cementing has been utilized in the industry since the turn of the century. Originally, wells were shallow and criteria for well integrity were somewhat limited. Since that time, wells have stretched the envelope in depth, temperature, and pressure. Environmental regulations have also become more stringent, thus, the importance of hydraulic isolation between permeable zones, and between these zones and surface has become more and more important.Initially, oilfield cements were comprised predominantly of construction cement and very limited additives. As time progressed, additives were incorporated to control pumping time or placement time and little effort was placed on optimizing actual components within the cement chemistry. This paper presents issues and concerns created by adding just one new component to the fundamental chemistry of an oilfield cement."

Jan 1, 2004

By Doug Smith, Gary Taylor, Paul Ogryzlo

"Uranium mining and processing typically requires large quantities of high-grade reactive quicklime for the neutralization and clean-up of contaminated mine water and mill process waste streams. Currently the Saskatchewan uranium industry’s lime requirements are being supplied from deposits located in Manitoba and Alberta, resulting in transportation costs, which equal or exceed the market value of the product. During the summer of 2001, the northern village of Pinehouse located 220 kilometers south of the Key Lake uranium mill, staked two previously discovered limestone deposits. The relatively shallow deposits, known as Missi Island and Sleeping Giant are located in close proximity to one another, approximately 35 km south of Pinehouse adjacent to highway 914. This paper describes the results of a scoping study carried out by AMEC for the development of the two deposits based on a seasonal limestone mine and a continuous 40,000 to 60,000 tpy wood fired calcining plant designed to supply all of the quicklime needs of the Saskatchewan based uranium industry. Also described are the results of calcining and customer acceptance testwork on samples of lime prepared from recent Pinehouse limestone drill core. The potential benefits of the project include a significant new source of revenue for the community of Pinehouse, lower lime costs for the Saskatchewan uranium industry and employment for northerners in the mining, processing and wood harvesting operations.IntroductionInterest in the Pinehouse/Massinahigan River area for limestone was precipitated by the results of a 1977 industrial minerals drill hole program by the Saskatchewan Department of Mineral Resources. These results led to the acquisition of land in the area by Missi Island Mines Ltd who carried out extensive exploration during the period 1978-1982. They discovered a deposit on the southwest side of the Massinihigan River thought to contain approximately seven million tonnes of limestone with an average grade of 94.5% CaCO3. Missi Island carried out preliminary feasibility studies and prepared an Environmental Overview Statement. However, in spite of positive recommendations, the project was dropped in the mid 1980’s."

Jan 1, 2003

By Eugen Gluck, Gus Van Weert, Peter Kondos

"Microwaves have the capability to heat up sulphides, especially clusters of particles of approx. 1 mm. Some sulphides absorb microwaves more readily than others. Molybdenite is especially effective in this regard, possibly due to its flaky nature and/or electrical conductivity. Even where it occurs in low concentrations in a deposit, individual rocks may be ore grade due to the high monetary value of MoS2. Such rocks often result from crushing mined veinlets or stockwork, or are contained in the cutoff grade fraction of ROM. Machine segregation of rocks high in MoS2 by infrared sensors after microwaving could therefore advantageously be used to upgrade lower grade ore between Mine and Mill. This would reduce the size of the latter, and thus its CAPEX and OPEX. Such upgrading could also yield shipping ore for a distant Mill, or extend ore reserves.Barrick Gold Corp. has been supporting the development of MW/IR sulphide sorting for the past three years. The results of MW/IR sorting work on molybdenite and other (pyritic) ore samples from a variety of sources are being presented here.INTRODUCTIONThis paper looks at mechanized, i.e. machine ore sorting technologies currently available and under development, and what conditions would be needed for the potential application of such ore sorting to sulphide mining and milling. Current machine sorting involves no-contact sensing technology for rocks, and signal processing after sensing to activate airblast segregation of certain rocks, normally the smallest mass to keep compressed air costs down.The forerunner of modern sorting is probably magnetic separation, which utilizes an inherent property of certain ores to divert it into mag and non-mags fractions. Radiometric ore sorters, which have been applied successfully for decades in the pre-concentration of uranium ores (Wotruba and Riedel, 2006) initiated modern sorting. In the 90’s, sensor-based machine sorting became a viable means of increasing the overall economic recovery of a resource. This technology became driven by the availability of low cost computing equipment and the concurrent development of algorithms, and by the availability of extremely fast response sensors and air actuators, allowing the sorting equipment to run faster, dropping the cost per tonne. It has been in industrial minerals processing that rock sorting has been most widely adopted, not really surprising. Liberation occurs on a different scale than in the base metal industry. Most industrial minerals are mined from massive deposits, requiring (in the past) no upgrading. Many of these operations now run into product contamination problems, which ore sorting can solve. One illustration: in Finland, a quarry is separating limestone from dolomite at 500 tonnes / hour, with individual rocks weighing up to 15 kg. Many of these industrial minerals operations have stockpiles of earlier discarded below-quality rocks, now being reprocessed with the help of ore sorting. The economics of this are very favourable, going from zero or negative value (stockpiles can not be left when closing the mine) to full product value for at least a portion of the stockpile. This suggests that in the future the economics of overburden sorting could become attractive under the right circumstances and such treatment could well become an integral part of open pit mine development."

Jan 1, 2009

By Andy Fortin, André Vien, Christophe Bouché, Jeff McKay

"The technology and equipment design of the Twenty-first Century permit us to exploit low-grade ore bodies with milled tonnages reaching 300,000 tpd. Because of their substantial operational costs (energy, wear parts, etc) and precarious economic situations, the operations of today must maximize their metallurgical performance.The implementation of an Expert System becomes a logical avenue to pursue in view of increasing plant performance.Many operations, following the implementation of an Expert System, meet the objectives they determined before its integration; such as increased tonnage, stability, decreased costs, etc. However, they often cannot develop the full potential of the system due to certain factors that have been neglected or omitted during the implementation of the system.Three main elements have been identified during the implementation phase at INMET Mining Troilus Concentrator: 1- Instrumentation & Control 2- Software 3- Integration. Even though they have been clearly identified, these elements are often neglected due to lack of resources or lack of comprehension on the part of the operations personnel. This document will demonstrate, based upon our experience at Troilus and that of Metso Minerals, that we can identify and handle many factors which influence the profitability of the Expert System, for both short and long-term process control improvements.INTRODUCTIONThe Inmet Troilus Mine is an open pit mine, situated 175 km north of Chibougamau in the province of Québec, Canada. The mill, which started production in November of 1996, was originally designed to treat a gold – copper ore at a rate of 10,000 tpd.In early 1998, the mine plan called for a pit pushback and decreasing head grades for the following two years. With the price of gold nearing decade lows, the Troilus project was facing a major economical setback. There was a sense of urgency to reduce operating costs below the market price of gold. The mill team presented a project to management calling for an increase in mill throughput while minimizing capital expenditures and operating costs. This idea was supported by the existing mine plan, which called for a mine cut-off of 0.7 g/t Au and stockpiling low grade 0.5 g/t material for future milling."

Jan 1, 2003

By L. Su, S. Liu, K. Jiang, K. Xie

The reduction of iron dissolution and acid consumption is fairly important in the extraction of Ni and Co from laterite ores from both economic and efficiency perspectives. BGRIMM conducted detailed research to investigate the behavior of iron in a nickel laterite leaching process. The mineralogy of Ni and Co was studied. In limonite ore about 76% of nickel is present in goethite while in saprolite ore 79% of nickel is associated with magnesium and silicon minerals. Test work revealed that limonite can be decomposed completely with enough acid concentration during atmospheric leaching. More than 98% of Ni and Co were leached into solution while 85% of the iron was also dissolved with 130-140 g/L iron in solution. Iron precipitates as hematite in the temperature range 250-270?C without neutralization reagents. That’s why limonite is treated by high pressure acid leaching (HPAL) technology to achieve nickel extraction and iron precipitation in the same autoclave. BGRIMM’s test results indicated that the remaining acid in atmospheric leaching solution and acid released by iron precipitation at a lower temperature was enough to leach saprolite efficiently. The so-called inverse leaching technology leaches limonite at atmospheric condition and the leaching slurry combined with saprolite is pumped into an autoclave to leach saprolite at 150-170?C. In the autoclave iron precipitates as hematite without acid consumption. Total nickel and cobalt extractions in the test program were more than 90% with iron content in solution below 8 g/L. In this inverse process iron dissolves in the atmospheric leaching stage and precipitates as hematite in the low temperature leaching stage. Compared with HPAL the leaching temperature is reduced to 150-170 ºC from 250-270 ºC. Compared to atmospheric tank leaching acid consumption is reduced from 850-950 kg/t ore (atmospheric) to 550-650 kg/t ore (inverse).

Jan 1, 2016

By S. Rajeswari, D. Gopi

"Pitting corrosion inhibition of 304 stainless steel (SS) in groundwater with a ternary inhibitor mixture (phosphonic acid + bivalent cation + various surfactants) was studied with different environmental variables such as temperature, pH, dissolved oxygen and chloride ions. Critical pitting potential and corrosion potential were calculated for these test media using electrochemical techniques. Under the tested condition, the localized corrosion resistance of 304 SS was determined and the results are discussed. IntroductionPitting corrosion of metals and alloys is a major cause of failure in chemical processing desalination plants, scrubber for flue gas desulphurization (FGD) plants, water storage tanks and pipelines, petroleum refineries, etc.Heat exchangers and condensers in inland thermal and nuclear powerplants utilize groundwater as a coolant, but materials of construction are generally prone to localized corrosion.Localized corrosion attack can be initiated when the passive film on the metal is disrupted. The presence of certain aggressive anions such as chlorides (Cl-) can migrate to the actively corroding area and stabilize pitting corrosion. Attention has been focussed on improving the resistance of stainless steel against localizedcorrosion in aqueous environments.One of the most accepted methods of avoiding corrosion is by the addition of chemicals (inhibitors). Over the past two decades, some phosphonic acids have been explored due to their good corrosion inhibition efficiency and low toxicity (Fang et al., 1993; Karman et al., 1998; Rajendran et al., 1998; Gopi and Rajeswari, 2000a). Bivalent cations like Zn2+ are often applied as additives to inhibit the metal dissolution (Sekine and Hirakawa, 1986; Aruna Bahadur, 1998)."

Jan 1, 2003

By Gordan Marrs, O. Matwijenko

"The Kidd Creek metallurgical site has been highly integrated to maximize revenues from its base metals mines. The site's operations include a Concentrator processing 4.3 million tonnes per year of copper-zinc ore, a Copper complex producing 100,000 tonnes per year copper cathode and a Zinc Plant producing 130,000 tonnes per year of zinc metal. To improve operating efficiency with increasing emphasis on productivity, process control, process automation and process optimization have been augmented and expanded during the last decade.New microprocessor based control systems provided the opportunity for the capturing of an expanded number of process related measurements. As supervisory computers were already in place, databases could be generated with only increased disc space and database management programs required. Once the data had been accumulated and stored, a method was then required for handling, screening and sorting large volumes of information in relatively quick and easy terms in order that the stored information could be used. By 1984, a decision to use personal computers for accounting, engineering and management reporting provided the vehicle necessary to handle this data. Using commercially available software, large volumes of stored process data can be downloaded from existing databases, filtered, sorted, analyzed, graphed, displayed, projected, reported and distributed. All this can be performed in very little time."

Jan 1, 1989

By J. E. Sepulveda, R. Morrow

"The Linear Wear Theory provides a reliable framework for the assessment of grinding media performance at full scale. This theory can be applied for analyzing grinding media consumption rates in any given grinding operation as well as the evaluation of alternative grinding media products, based on actual operational data, correcting for conditions like ore hardness, feed and product sizes, mill power and circuit throughput; all of them unrelated to the grinding media intrinsic quality attributes. A series of Moly-Cop Tools 3.0 applications have been developed to facilitate the calculations involved. Moly-Cop Tools 3.0 is available, free of charge, to all interested parties through the corresponding author.INTRODUCTION Mineral grinding circuit operators recognize the significance of grinding media (balls) consumption on the cost structure of any full scale grinding facility. The effective cost associated with this essential consumable depends on two factors: delivered price and durability (quality) of the grinding media. When evaluating alternative grinding media varieties, there is a well accepted evaluation criterion by which a given media type is considered to be “cost-effective” when its unit application cost – normally expressed in $/ton of ore ground – is shown to be lower than that of a nominal reference condition: Grinding Media Cost = Ball Price x Ball Consumption (1) ($ /ton ground) ($/ton balls) (ton balls/ton ground) Under this criterion, an alternative, higher-price grinding media product could be “cost-effective” if its associated consumption rate is sufficiently lower than the reference media, enough to yield a lower grinding cost, as dictated by Equation 1. For the proper application of the above criterion, evaluators must rely on representative indicators of grinding media quality, ideally independent of most mill operating conditions. In each particular case, ball price is always a known component; however, it is not so evident how media performance (quality) differences amongst alternative product types could be assessed with a reasonable degree of accuracy and precision."

Jan 1, 2014

By H. D. Stolovitch, M. L. Lavallée

"An engineering system used to analyze and improve the performance of industrial grinding circuits has been adapted into a training program. The systematic approach to the design of training was applied in order to:Determine if training was an appropriate and effective tool for the transfer of this new technology;Define the technical content of the program;Establish program specifications based on learner and context characteristics;Design and test prototypes of the instructional modules; and,Establish a strategy for plant implementation and maintenance of the training program.This paper thus describes how a engineering system is transferred to the workplace through the use of designed instruction.INTRODUCTIONTraining can change human performance in a permanent way. It can improve productivity for the overall benefit of an operation. Organizations can therefore use training as a mean to achieve their specific goals. Training is not the solution to every performance problem. However, in many cases, it can be a very effective way to attain desired performance.The benefits of training are often difficult to assess. However, to remain competitive, organizations must introduce new products and innovative technologies. Often, they can do both most effectively through suitable training interventions.In order for the effort and investment of training to provide optimal results, two points of view should be adopted.• An overall view of the system in which training is to be applied.• A systematic approach to the design of training (Stolovitch and Keeps, 1989)."

Jan 1, 1992

By R. E. Jones

"INTRODUCTIONCominco Limited, one of the free world's largest producers of lead and zinc having majority ownership in Pine Point Mines Ltd., operates a mining and concentrating complex on the south shore of Great Slave Lake in the Northwest Territories. The mine was developed in 1963-64 and commenced operation late in 1964 with the direct shipping of high grade ore. The concentrator started production in November 1965 at a design throughput rate of 5,000 T.P.D.In 1968, the Company acquired the mining rights to a large ore body located to the east of the Pine Point claims and subsequently an expansion program at the concentrator raised the throughput rate to 8,000 T.P.D. The expansion included a third grinding circuit and additional flotation capacity. The flotation capacity took the form of a completely separate circuit from the existing flotation plant. In 1972, the zinc flotation circuits were modified to include two additional stages of cleaning. This change concluded the ""Pre-Consolidation Flotation"" circuit at Pine Point.In considering these modernization programs of the flotation section of the concentrator, the philosophy was to utilize the largest available machine having proven and modern technological changes. With the advent of the large capacity machines available in the late 1970's, it was considered a suitable time to revamp the entire flotation circuit at Pine Point in 1979. The Circuit Consolidation Project was developed to meet this requirement."

Jan 1, 1982

By R. Tessier, C. R. Larsen

"INTRODUCTIONOn November 10, 1982 Nor and a Inc signed an agreement with Golden Sceptre Resource Ltd. and Goliath Gold Mines Ltd. to construct a mine and milling facility.The Golden Giant mine is located in the Marathon area of north - western Ontario, immediately north of Highway 17 and about- 3.5 km west of Highway 614.With the exception of selected unit processes, the mill was designed for a nominal throughput of 2500 tonnes per day with early operating data to be used to identify sections requiring possible expansion to achieve an ultimate throughput of 3000 tonnes per day.Commissioning of the highly instrumented milling complex which includes crushing, grinding, cyanidation, and carbon in pulp processes commenced in February 1985. After water testing various sub-circuits from grinding through tailings, waste ore was introduced to ensure proper mechanical and electrical operation of process equipment.The first ore was milled as a mixture with waste on March 4, 1985. The first gold bullion was poured April 6, 1985.Initially, ore was only available from mine development at a rate of 700 t/d, which was milled at a minimum rate of 1200 t/d. While regular weekly shut downs of two to three days was useful for mechanical maintenance, changes, and modifications, process tuning was more difficult due to the non-steady operation. As increased quantities of ore became available, regular weekly shutdowns tapered off and process operation improved accordingly. For testing purposes and as ore was available, mill throughput was increased regularly to 2300 t/d and for very short periods of time to nearly 3000 t/d.No major design or operating problem has been encountered to date. The following is a brief description of the milling process and various operating highlights. Process flowsheets are shown in Figures 1 through 6."

Jan 1, 1986