Search Documents

By Fernando Romero Lage

"Crushing and screening theory and application has remained fairly consistent in the last 50 years. The application of such equipment is guided by varied formulaic conventions and rules that due to the entropic nature of the process, remains more an art than a science. The variability of conditions creates an environment in which trial and error becomes the principal means of process balance and control. This paper illustrates some of the theories behind the process, plus other assumptions, postulates, myths and misconceptions that exist within the crushing and screening industry.INTRODUCTIONContinuous material balance calculations are habitually performed in the design of new comminution circuits as well as in the valuation of existing circuits. A continuous material balance calculation is one in which the input rate of material is equal to the output rate for each unit functioning in the circuit. At continuous analysis, there is no accumulation or losses of material within the system, as it is when performing a discrete event analysis.In order to produce viable and manageable mine-to-mill material, whether it is ready to leach or ready to mill, we must reduce the material in a series of stages. The power demand increases as the material size decreases, as it is when folding a piece of paper successively. As with the paper, there is a crushing size limitation that is a consequence of the mineral properties such as work index, moisture, viscoelasticity, etc. Comprehensive knowledge of crushing plants in both the aggregate and the mining industries show that, after three stages of crushing, a particle size distribution originating from a blasted deposit can be reduced from an nominal maximum size of 500 mm to a nominal maximum size of 12 mm. if the last stage of crushing is set in closed circuit, the screen openings will be able to yield a smaller top size.Achieving steady and continuous material balance poses major difficulties as crusher lose their settings, screens blind or peg, and material characteristics change geographically or seasonally. Overloading conditions in crushers and screens are nothing but counterproductive, and the net losses of an unbalanced circuit can be overlooked when mining operators are paying a lot more attention to the evermore complex systems downstream.It is not simply the crushing of the mineral but achieving the right size for the downstream milling process that will yield the maximum amount of energy savings."

Jan 1, 2010

By Brent C. Jellicoe, Phil Robertshaw, J. Murphy, Peter Williamson

Kimberlites and associated diamonds have been the focus of extensive exploration in central Saskatchewan since 1988. During 1989, Uranerz Exploration and Mining Limited identified 71 shallow magnetic anomalies in the Fort a la Corne area from detailed aeromagnetic surveys. By the end of 1991, 18 of these targets had been proven, by drilling, to be kimberlite bodies encased within Cretaceous sedimentary strata. From 1991 to 1997, the number of drill-confirmed kimberlite bodies increased to 69. Our current view, drawing on an integration of geophysical and geological information, is that the kimberlites are composed of individual bodies and multi-vent clusters of coalesced bodies, all apparently constructed of stacked, temporally distinct layers of pyroclastic crater-facies kimberlite. Diamond recoveries and geochemical results from associated heavy minerals at Fort a la Corne remain highly variable, although continued minibulk sampling is expected to improve the estimation of diamond grades for the most prospective bodies.

Jan 1, 2001

By Kah Lert

"The Red Mountain porphyry molybdenum deposit is situated in the Big Salmon Range, approximately 80 km east-northeast of Whitehorse, Yukon.Red Mountain is underlain by Paleozoic, argillaceous sedimentary rocks of the Yukon Cataclastic Complex, which have been intruded by a multi-phase mid-Cretaceous stock.Mineraliwtion, quartz stockwork, metal zonation, and an alteration assemblage characteristic of a porphyry molybdenum system have been superimposed on quartz monzonite porphyry and adjacent homfelsed sedimentary rocks. A later, barren and pyritic quartzeye diorite porphyry body and related dikes have dissected the quartz monzonite porphyry, homfelsed sedimentary rocks and associated molybdenite mineralization.Drill-indicated geological reserves of molybdenum mineralization outlined consist of 187 270 000 tonnes grading 0.167% MoS2.IntroductionLocationThe Red Mountain porphyry molybdenum deposit is located at 60°59'N, 133°44'W (NTS 105 C), approximately 80 km east-northeast of Whitehorse, Yukon. The property is situated within the rugged Big Salmon Range, 15 km east of the north-northwest-trending Teslin River. Red Mountain, at an elevation of 1702 m, consists of relatively steep, talus covered slopes with prominent gossanous bluffs marking the southeast flank. Relief on the property is 700 m, with tree-line at an elevation of 1450 m to 1500 m (Fig. 1)."

Jan 1, 1995

By K. Lundholm, A. E. Mäkinen

"Ore grades are declining and getting more complex around the world which not only complicate the ore processing but also produce new type of requirements to manage the produce waste streams. One specifically problematic and increasingly identified element in waste streams produced in mining and metallurgy is arsenic.Arsenic is a compound that has no significant market value, but that needs to be removed from ores, concentrates and other process streams because of environmental or process technical reasons. One example of a removal process is partial roasting of high-As sulfide concentrates, originally developed by Outotec. In this process the arsenic is volatilized in the gas phase and thus separated from the solid material, i.e. the calcine. If the arsenic is recovered by wet methods the process gas is quenched and all arsenic needs to be stabilized in the effluent treatment plant.Outotec has developed ferric arsenate precipitation as a method to produce stabile arsenic residues from wet gas cleaning effluents. Iron based precipitates, when correctly produced, can meet typical landfill criteria measured with different types of leaching methods meant for characterizing the arsenic dissolution behavior from the precipitates.In this paper partial roasting of sulfide concentrates with arsenic volatilization in combination with ferric arsenate precipitation is discussed from the perspective of producing wastes that can meet the stability requirements set by common leaching tests methods, TCLP and CEN. These leaching test methods set the normative landfill requirements for most operations generating arsenic containing wastes. A typical flow sheet of Outotec® Ferric arsenate process is discussed with results showing the importance of correct process control and sequence on producing arsenic containing waste that can meet the landfill disposal requirements."

Jan 1, 2014

By R. H. Pemberton

"THE Mattagami district of Quebec has, during the past few years, experienced intense exploration by virtually every mining company operating in Canada. As a result of this activity, a number of well-mineralized zinc-copper bearing bodies have been found, some of which will almost certainly go into production. Much of the area has undergone what is now termed ""Saturation Prospecting"" or intense and detailed geological and geophysical surveying, followed by the drilling of nearly all possible bets. Considering only the airborne geophysical surveying, some blocks of ground have been flown by virtually every geophysical instrument which has to date been installed in an aircraft. A list of these different geophysical instruments would include: l. Fluxgate-type total field magnetometers 2. Vertical field magnetometer ,3. Nuclear-precession magnetometers 4. Single-frequency out-of-phase electromagnetometers 5. Dual-frequency out-of-phase electromagnetometers 6. Horizontal component measuring electromagnetometers 7. In-phase and out-of-phase electromagnetometers8. Dip-angle measuring electromagnetometers."

Jan 1, 1961

By G. Lee, E. T. C. Spooner

"Molybdenum mineralization at Boss Mountain is hosted by the Triassic Takomkane quartz monzodiorite batholith and is associated with a Cretaceous monzogranite stock. Ore has been mined from a sheeted vein system that describes a partial annulus centred upon the apical region of the stock and from subvertical breccia pipes that emanate from the stock. Molybdenite precipitation is coincident with CO2 effervescence from a dilute (1.9 mole o/o NaC/ equivalent) hydrothermal fluid over a temperature range of 250°C to 370°C at a pressure of approximately 350 bars, interpreted to be greater than or equal to the lithostatic load and equivalent to a depth of 1.3 km or less.IntroductionThe chemical and thermal constraints on molybdenum transport and deposition to form molybdenum ore deposits are not well understood. To address this problem, the Boss Mountain mine in central British Columbia, operated by Noranda Mines Ltd., was chosen as a well-described (Soregaroli and Nelson, 1976), relatively small and simple example of a Cordilleran Mo~ deposit. It is situated on the northeast slope of Takornkane Mountain, 10 km west of the community of Hendrix Lake (N.T.S. 93A/2W; latitude 52°06'N, longtitude 120°56'W). Access is from 100 Mile House by nearly 90 km of road, the first 50 km of which are paved."

Jan 1, 1995

By A. del Campo A.

The roast segregation process, which was patented in 1974, makes use of a set of chemical reactions that are different from the traditional sequential oxidation of iron and copper sulfides used by all modem pyrometallurgical processes to treat copper concentrates. It allows metallic copper to be obtained via sublimation of copper chloride at temperatures in the range of 700-800 OC. In addition it avoids melting the concentrate, doesn't require transferring molten materials, doesn't need flux addition and allows nearly all of the sulphur to be removed in one stage as a high-S02 gas stream. Most importantly, it allows a decrease in the use of energy to approximately 6 million BTU/ton of anodes. This represents a saving of approximately 40%, compared to the potential of the most advanced processes presently used. Such a promising process has been waiting for its first industrial application for more than 30 years. This article examines the technical difficulties that have delayed application of the roast segregation process to beneficiate copper concentrates. Special emphasis is made on material handling aspects, discussing the possibility of using a well designed mass flow silo as the main processing vessel to carry out the segregation stage. Cu2007

Jan 1, 2007

By Staff

Introduction As the Sherritt Gordon property is still in the development stage, . it is rather difficult to write a proper account of the mining methods and milling practice that will be used. While the general scheme of operation will remain the same, there will undoubtedly be many minor changes to meet special conditions which we cannot forsee at the present time. Most of the work accomplished to date has followed the usual routine of preliminary development in the Canadian North. However, we have learned a few things which might be of use to others operating under similar conditions. The most important of these is the saving in power cost made possible by the use of Diesels as against steam power when using wood fuel, and the movement of freight by tractors when rail transportation is not available. Location The property i6 located about 90 miles north of The Pas, or 40 miles northeast of the Flin Flon mine. A branch line from Cranberry Portage, on the?C. N. railway, between Flin Flon and The Pas, connects the property with the outside.

Jan 1, 1930

By Mani Manimaran, Inna Dymov, Mariam Melashvili, Chris Fleming, Joe O’Day

This paper presents experimental evidence that supports the use of bromine/bromide as a potential alternative to conventional cyanidation for gold leaching. The study evaluated a brominebased lixiviant, Stabilized Bromine, with considerably lower vapour pressure than liquid bromine. Using a rotating device, the rate of gold dissolution was determined at various concentrations of this reagent. The reactivity of pure pyrite, arsenopyrite and chalcopyrite minerals was also evaluated in stabilized bromine reagent. Furthermore, bromine leaching of gold in a number of gold bearing ores was undertaken. Results showed that significantly higher gold recovery can be achieved with bromine than with cyanide when leaching gold encapsulated in sulphides, but bromine consumption was high owing to simultaneous oxidation of the sulphides. The greatest promise for the bromine leach process was with oxidized gold ores. The recovery of gold from oxide ores with bromine was comparable to that achievable with cyanide and bromine consumption was reasonable when leaching was conducted at a near neutral pH of ~6. In the case of oxidized gold ores containing copper mineralization, it is possible that bromine consumption may be lower than cyanide consumption, since there is evidence to suggest that bromine is less reactive than cyanide with copper minerals.

Jan 1, 2014

By Walter Herd

For the past eight years, No. 2 mine of the Cumberland Railway & Coal Co., Springhill-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Depart~ of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. °This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of Public Works and Mines, Nova Scotia. Prior to 1925, the room-and-pillar method was employed, and in January of that year (there being a cessation of work from March to August due to labour troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine, was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence had not been experienced. In ?the interval, development work for longwall retreating below the 5,900-foot level was vigorously pushed.

Jan 1, 1929

By A. Lewis, J. Zachwieja, M. Widell, P. Zhou, W. W. Geissler, M. Svensson, A. Movahedi, H. Nordberg

Flotation collectors for sulfide minerals has been traditionally based on xanthate, thiophosphate, thiophosphinate and thiocarbamate, all derived from sulfur chemistry. Tecflote™ is a new family of patented collectors based on nitrile chemistry which can supplement or replace thiol collectors, depending on the ore types. A steep grade-recovery curve typical of Tecflote™ collectors was observed when using Tecflote™ as the main collector for the rougher and cleaner steps allowing a better recovery compared to current thiol collectors while maintaining the desired grade. Additional recovery increase has also been observed by the addition of scavenger steps using Tecflote™ collector in combination with current thiol-based collector. The selectivity seen in the lab is transferred to full scale trial and is clearly seen in the rough flotation where the increase in the rough concentrate grade of 5% after pumping Tecflote S11 directly into the tank cell. The mechanisms for Tecflote’s selectivity towards sulfides are currently under investigation and will be discussed. Results of TOF-SIMS analysis will be presented, demonstrating the collector’s selective affinity to different mineral surfaces in flotation. INTRODUCTION The history of collectors used today started in 1882 when Zeise first made xanthates. It was first used in flotation in 1925 – Cornelius Keller’s first patent (Fuerstenau, Jameson, Yoon, 2007). Between 1928 and 1930 American Cyanamid filed 7 patents for dithiophosphate, including flotation and chemical synthesis of the reagent, the first of which was filed by Christmann in 1928 (Christmann, 1933). Synthesize of thionocarbamates for mineral flotation was filed in 1954, by Dow Chemical Company (Harris, 1954). Now that the head grades have been declining over the last decades the need to find more selective collectors to extract difficult and complex ores has pushed the industry to look at different chemistries. Thiol collectors standard to the industry rely on the sulfur in the collector molecule to bond to the mineral surface. The electronic property of this group is modified by the adjacent chemical groups, such as additional S, P or N have the effect of changing the selectivity of the collector (Wills & Finch, 2016). In the case of xanthate the length of the hydrophobic group also has an effect on the selectivity with some minerals such that the ethyl xanthate is more selective against pyrite and pyrrhotite than the long chain xanthates (Wills & Finch, 2016).

Jan 1, 2019

By N. Behnood

"This paper describes how material selection, quality assurance, and failure investigation play important roles in the efficiency and safety of mining and metallurgical operations.INTRODUCTION Material selection, quality assurance, and failure investigation are all complementary elements of materials engineering in the application of materials technology for failure prevention. Based on commodity price increase of 300% between 2002 to 2013 [1] and increased cost ofcapital projects and operation, equipment failure, which in some cases causes complete shutdown of the operation, becomes a vital importance in mining and metallurgical plants. The following sections present a number of examples from many failure cases experienced by the author during his three decades of work as a materials engineer in the mining industry."

Jan 1, 2015

By Marcel Vallée

Frequently, costs overruns and defaults in mining project performance result in serious problems and headaches for all project participants and impact on corporate objectives, profits and image and, occasionally, lead to project failure. As mining professional s, we should be very concerned that, in a recent World Bank paper (Weber-Fahr, 2001), geological and technical risks were considered the most important ones facing mining projects. Whenever we manage to reduce or minimize these risks, we are in better position to overcome the environment-, market-, finance- and community-related ones. The causes of this situation seem rather systemic, as a fairly long list of industry problems with new pro jects has been described in industry papers in pas t and recent years. A brief review of industry problems with mining projects will be given first, followed by a review of the basics of the current Quality Management and Continuous Improvement perspectives that have evolved from earlier quality control and quality assurance systems and policies. Particular particular attention will be given to the work of W. E. Deming. As the system approach is an essential part of such policies, it will be described succinctly. Given that poor communications and interactions among geologists, mineral processors and mining engineers/operators ca n seriously affect project efficiency and profitability, these interrelated processes with in the mining systems will be analyzed and modelled and the impacts of such situations will be described through a number of anonymous case histories and examples. A synthesis of Dr Deming's management system, includ ing his Four teen P oints and System of Profound Knowledge, will be prese nted .

May 1, 2002

By R. Bruce Ferguson

"IntroductionThe Beaverlodge Operation of Eldorado Nuclear Limited is a uranium property located near the north shore of Lake Athabasca about 7 miles from Uranium City, Saskatchewan.The mill is a 2000 tpd carbonate leach operation producing a high grade yellowcake concentrate.The Lamella Thickener was purchased to replace a 55 foot conventional unit which had deteriorated beyond repair. The cost of the unit was considerably lower than for a conventional unit, installation was much simpler and the unit is much more compact allowing it to be installed in the mill basement and be insulated completely.The unit was sized according to the results of tests performed both by the supplier and Beaverlodge engineering staff. The supplier guaranteed overflow clarities of less than 100 ppm suspended solids. The Lamella thickener was developed by A. Johnson Co. of Stockholm, Sweden, is manufactured under license by Parkson Corporation of Ft. Lauderdale, Florida and is distributed in Canada by A. Johnson Co. of Montreal."

Jan 1, 1975

By W. E. Roscoe, H. Agnerian

The contour method can be used to estimate the mineral resources of a mineralized body. It relies on geological interpretation and allows the geologist to determine the plunge of a mineralized ore shoot along the dipping plane of the mineralized body. The technique is best applied to estimate tonnage and average grade of relatively planar bodies, i.e., where the two dimensions of the mineralized body are much greater than the third dimension, such as Archean lode gold vein deposits or mantos of massive sulphide mineralization, based on exploration drilling. For these types of deposits, the contour method can provide a clear view of the “mineralization landscape” with “peaks” and “valleys” along the plane of the mineralized vein. The technique also reduces the “nugget effect” of local high values commonly present in gold deposits. With sufficient drill hole information, the contour method may be used to estimate the tonnage and average grade of individual blocks within a mineral deposit. General procedures for the contour method are described in this paper, along with examples and explanatory notes.

Jan 1, 2002

By B. Dubé, R. Friedman, J. Oliver, R. Aubertin, M. Burson, G. Panneton, M. Hamilton, J. Ayer

"The Detour Lake gold deposit is located within the northwestern limit of the Archean Abitibi Subprovince of the Superior Province. Mineralized zones are hosted by a sequence of pillowed and massive flows, hyaloclastite units, and altered ultramafic rocks, and are commonly oriented parallel to a series of high-strain zones that are co-planar to the regional-scale Sunday Lake Deformation Zone. Early in its kinematic history, the Sunday Lake Deformation Zone placed older (2.72 Ga) volcanic rocks of the Detour Lake Formation over younger (2.70 Ga) sedimentary rocks of the Caopatina assemblage. Gold mineralization is also parallel to the position of a laterally persistent siliceous rock unit, the 2.725 Ga ‘Chert Marker Horizon.’ The Chert Marker Horizon coincides with the boundary between the mafic-dominated upper Detour Lake Formation and the ultramafic-dominated lower Detour Lake Formation. Stratigraphic and geochronological data suggest that the Chert Marker Horizon is a deformed felsic volcaniclastic unit. At a cut-off of 0.6 g/t Au, the Detour Lake deposit contains 17.26 million ounces of Au within 445.9 million tonnes of rock grading 1.20 g/t Au. Gold occurs in shear-hosted and extensional vein arrays within rocks of the upper and lower Detour Lake Formation and within the Chert Marker Horizon. The Detour Lake deposit has many of the characteristics of a greenstone-hosted, quartz-carbonate vein deposit; its very large size may be attributed to large-scale rheological controls resulting in the formation of dilatant sites in permissive rock units."

Jan 1, 2012

By Patrick Cloutier

Presentation objectives ? Introduce discrete-event 3D computer simulation as a tool to design, improve and optimize construction projects: ? Describe a real typical construction project planning issue. ? Present an applied use of simulation to solve this issue. ? Detail benefits of using simulation versus traditional planning methods.

Aug 1, 2013

By M. J. Collins

"Autoclaves were first used in the metallurgical industry in 1893 to recover alumina from bauxite. In the 1940s and 1950s, several high temperature and pressure processes were invented in the laboratory of Professor Frank Forward at The University of British Columbia, in parallel with advances in equipment and processes by the Chemical Construction Corporation. Sherritt Gordon Mines Limited enlisted these groups to help develop the nickel sulfide ammonia leach process that was commercialized in 1954. Autoclave processes that have since been commercialized include high-pressure acid leaching of laterites, zinc pressure leaching, and pressure oxidation of refractory gold feedstocks. RÉSUMÉ En 1893, l’industrie métallurgique est la première à utiliser les autoclaves pour l’extraction de l’alumine dans la bauxite. Dans les années 1940 et 1950, plusieurs procédés à haute température et à haute pression sont inventés dans le laboratoire du Pr Frank Forward de l’université de la Colombie-Britannique (UBC) ; parallèlement, la Chemical Construction Corporation fait de grands progrès en matière d’équipement et de procédés. Sherritt Gordon Mines Limited fait appel à ces groupes pour qu’ils aident la société à développer le procédé de lixiviation du sulfure de nickel dans de l’ammoniaque, commercialisé en 1954. Les procédés de lixiviation en autoclave commercialisés depuis incluent notamment la lixiviation acide à haute pression de latérites, la lixiviation sous pression du zinc et l’oxydation sous pression des matières premières de l’or réfractaire.INTRODUCTION Autoclaves are chemical reactors that are built to contain processes taking place at elevated pressure. They are used in metallurgical refineries throughout the world to take advantage of the increased reaction kinetics and different reaction products that can be obtained in aqueous systems above the boiling temperature at atmospheric pressure. The word autoclave comes from the French “auto” and the Latin “clavis” and literally means self-locking—that is, the core distinguishing feature of an autoclave is that it includes a means for pressure regulation (e.g., a pressure relief valve). Denis Papin (Figure 1a), one of the inventors of the steam engine, was the first to make use of a safety valve to control steam pressure. He is credited with inventing the autoclave in 1679. Papin’s “digester” (Figure 1b) was a type of pressure cooker that was originally used to liquefy bones. Most commercial autoclaves are horizontal, multicompartment vessels with mechanical agitation, as shown in Figure 2a; however, the steam-agitated Pachuca vessels used to leach laterite ore in Moa, Cuba (Figure 2b), are also classified as autoclaves according to the self-locking definition provided above."

Jan 1, 2018

By David O. DeGagné

While mine backfill plants are becoming increasingly more automated and instrumented, especially with paste fill operations, underground backfill distribution systems have hardly changed over the years. While fill properties are appropriately measured in the preparation plants, as backfill enters the mine borehole, the technology for control, data gathering and reporting is somewhat lacking. Mines typically experience problems with borehole and pipeline plugging, pipeline bursting, bulkhead failure and exposed fill sloughing. With adequate instrumentation of the backfill system it is possible to obtain a complete, continuous and detailed picture of the entire filling operation from preparation to post-pour. Good data will, over time, provide the basis for needed improvements of backfill systems and will be essential to safer, more efficient and less costly fill practices. This paper will review the areas of the filling operations where monitoring would prove critical to eliminate failures such as pipelines, bulkheads, fill exposures, stope walls, etc. The types of monitoring systems currently available will be reviewed and potential areas for development will be highlighted.

May 1, 2001

By M. M. K. McCrank

"PRACTICAL SAMPLING TECHNIQUESIt is important to achieve reliability when sampling heterogeneous materials where there is a difference in composition, and non random distribution of the constituent particles. Throughout the design, construction and installation of sampling systems it must be borne in mind that the sampling point must be capable of:-allowing each particle in the stream an equal opportunity to be sampled.-accepting and collecting as large a volume or mass of material as necessary to satisfy the requirements of particle counting statistics.-establishing a sampling plan so that the sample is representative of the whole to a defined standard of accuracy.Design ConsiderationsFactors that may influence the design of the sample point include:-the mass, or volume flow rate of the material being sampled-the size and shape of the material or flowing stream-the physical condition of the material being sampled (i.e. temperature, wetness, size consist, density).-the chemical composition of the material being sampled -the location of the sample point and the space available for installation, extraction, reduction where necessary, secondary sampling, and return of the sample rejects downstream.-whether the process to be sampled is in an existing plant or one yet to be designed and built.-ease of access for servicing and maintaining the equipment.-whether the sampled material must be collected continuously or intermittently.-whether an existing sampling method is likely to be adequate or whether a new technique has to be developed."

Jan 1, 1989