Search Documents

Experimental Mine, Val d'Or, Quebec, Experiments on the ignition of sulphide dust clouds by explosives have been conducted in a 1 m3 explosion chamber. The explosives tested are ANFO, emulsion, aluminized emulsion and Detasheet. By controlling the composition of the ANFO and the emulsion explosive the oxygen balance could be changed in order to identify the dominant factors in the ignition of sulphide dust clouds by explosives. Experimental results, combined with theoretical calculations, show that the temperature of the detonation products is the most important parameter in the ignition of the dust cloud while the combustible detonation products are of secondary importance in the case of non-aluminized mining explosives. In the case of aluminized explosives and explosives having very negative oxygen balance the ignition of the dust cloud is assisted by the large amount of combustible detonation products.

Jan 1, 1993

By M. F. Lopez, A. J. Mattus, S. B. Magid, D. B. Mobbs

"The use of Caro's acid as a replacement for hydrogen peroxide for the oxidation of vanadium prior to solvent extraction resulted in a 56% reduction in oxidant usage when compared on an equivalent hydrogen peroxide basis. Comparative oxidation tests, using two actual uranium mill raffinates, resulted in premature precipitation of an amorphous ferric vanadate when hydrogen peroxide was used to oxidize one of the raffinates containing a high iron to vanadium ratio. The use of Caro's acid eliminated the precipitation problem, thereby permitting the adjustment of the raffinate pH to a higher, more favourable level prior to solvent extraction.Potentiometric characterization of the raffinates revealed that vanadium is responsible for the inefficiency of hydrogen peroxide compared with Caro's acid, with the oxidation efficiency of iron being the same for both oxidants. A limiting potential between 720 and 740 mV was observed when using hydrogen peroxide, while, when using Care's acid, potentials approaching 1200 mV were achievable.A four-stage, countercurrent extraction performed on the oxidized raffinates did not reveal any operational problems. The extraction efficiency and the extraction coefficient were found to be higher when Caro's acid was used as the oxidant, as opposed to hydrogen peroxide.IntroductionMost vanadium is recovered as a by-product of some other process: leaching of Carnotite uranium ores, oil fly ash, phosphate rock or chromite processing. The major source of vanadium has been from uranium mills incorporating acid leaching of Carnotite ore s at elevated temperatures and pressures. The by-product recovery of vanadium from uranium ores of the Uravan Mineral Belt, located in the Colorado Plateau , is a common occurrence when vanadium recovery is economically viable."

Jan 1, 1983

By M. S. Badollet

INTRODUCTION THE DEMAND for general knowledge on asbestos fibres has increased considerably in recent years. A few publications have printed data showing some of the physical and chemical prupertie3 of asbestos, but in many cases this information is difficult to find and is seldom available when needed. During the past ten years, Johns-Manville have received many inquiries on the physical and chemical properties of asbestos fibres. Fortunately, we had some of the information in our files, and we willingly supplied the data. To help relieve this need, we have tried to present briefly in this paper some of the interesting and out-standing properties of asbestos. This information was obtained over a period of years by search of the literature and by experimental investigations. PROPERTIES OF ASBESTOS FIBRES Table I (1, 2) presents, in convenient form for easy comparison, data on the principal properties of the several varieties of commercial 'asbestos' -actinolite, amosite, anthophyllite, chrysotile, crocidolite, and tremolite. Under each variety of fibre is a brief statement describing the properties in terms of structure, mineral association, origin, etc. Some of the more important data in Table I are expanded and presented in Table II (3). SOLUBILITY OF ASBESTOS A report ( 4, 5) discussing the effects of acids and caustic on asbestos fibres was published in Germany in 1927.

Jan 1, 1951

By Fred Delabbio

There are presently several issues that the mining industry is facing, such as underground air quality, deep mining and green house gas emissions, which could be addressed by the application of alternate energies. Several aspects must be considered by the industry in any drive to introduce new technologies within the context of a producing underground mine. This article presents several operational and support aspects that will evaluate the relevance of alternate energies, with emphasis on hydrogen power systems: operational drivers, commercial supply of technology, site supply system requirements, health and safety, capital and operating costs, mine production, corporate philosophy, and role of government. It is concluded that introduction of alternate energy technology requires a step-wise progression: Applicability to the industry, proof of concept testing, development of generic infrastructure, power systems and regulations, whole system studies and detailed studies of cost and risk versus benefits. The current initiative to apply fuel cells is at the proof of concept stage, entering the generic infrastructure stage.

May 1, 2007

"The Antamina orebody is a geologically complex, polymetallic skarn located in the Peruvian Andes. A range of copper and copperzinc ores are campaigned separately through the concentrator producing copper and zinc concentrates as well as lead and molybdenum by-products.Ore type classification at Antamina is based on chemical assays; geological or lithological variations are not considered. Consequently, each ore type demonstrates a wide range of concentrator performance.Antamina is currently implementing a system to track ore movements from the shovel face to the concentrator. Relatively sophisticated models of run-of-mine and coarse ore stockpiles ahead of the mill will be used to account for the variable delay between mining and milling.One of the numerous benefits of ore tracking is the ability to directly associate the measured concentrator performance with a physical location in the orebody. Using existing mine planning software, three-dimensional models can be created of such performance measures as metal recovery, concentrate quality, operating cost, and reagent consumption.Such a database of information allows the true value of different ore sources to be determined. The value of an ore source is conventionally measured as metal content (individual or combined ‘equivalent’) with a cut-off grade applied to indicate some base level operating cost. However, the true value of an ore source should include dynamic factors like haulage cost, reagent use, smelter penalties, and even prevailing metal prices. If an ore source is considered from all perspectives rather than simply its potential to deliver value, the concept of ore becomes more flexible. Any ore source that reveals itself to be unprofitable can be eliminated from the mine plan or possibly blended with others to improve its value. The ability to predict mill performance, and thereby profitability, is a powerful tool.In an operation such as Antamina, where managing ore sources, campaigns, and the delivery of a variety of concentrates in a narrow timeline to customers is a daily challenge, prediction is the key to success and improved efficiency."

Jan 1, 2005

By David W. H. Ellis

This presentation will discuss over 2 dozen past, present and future oils sands projects in Alberta. The very early projects as well as the most recent along with the ones that never got off the ground and the ones in production are all included. For each, the following will be given (where known): owners, location, type (mining/SAGD/refinery), production, capital budget, spent to date, status. Some overall impacts will be discussed.

May 1, 2004

By J. A. McLennan

Nickel laterite deposits are typically formed from tropically weathered mafic-ultramafic complexes. The resulting nickel concentration is found within soil horizons and is mineable with regular dozer units. At the time of mining, digging elevations are needed at selective mining units (SMUs). Moreover, for mine planning, the costs due to dilution and lost ore require mining elevations to be specified. A conditional simulation approach is used to calculate ?optimum? SMU mining elevations. Multiple realizations of the ore base surface are simulated. For a single bottom surface realization, dilution and lost ore costs are calculated over the entire vertical extent of each SMU. The optimum mining elevation is the elevation where the lowest summed cost of ?accepting dilution? and ?wasting ore? occurs. The reported SMU dilution is the cost of mining the volume of waste located below the bottom surface and above the optimum mining elevation and the reported SMU lost ore is the cost of not mining the volume of ore above the bottom surface and below the optimum mining elevation. For all ore bottom surface realizations, optimum SMU mining elevations and their associated dilution and lost ore costs are calculated and compiled to represent production uncertainty.

Apr 1, 2005

By A. M. Hill

"This is an account of the expansion of Texasgulf's Timmins concentrator by the building of a fourth circuit.The original capacity of the mine and concentrator was 3.6 million tons per year of ore. In 1974, Texasgulf decided to increase that capacity by about one third to 4.8 million tons per year. It was planned that the increased capacity would be available by mid-1978.The expansion involved work at the rninesite, increased railroad capacity, and a new circuit in the concentrator, and it is the concentrator expansion which is described here.In 1974, the minesite drew its ore from the open pit. The pit was being phased out and was to be replaced by No. 1 mine. To allow for the expansion, a second mine was required. The railroad was capable of handling 18 car trains. Its capacity had to be increased to 27 cars per train and this, in turn, required two new locomotives. Each of these alone cost half a million dollars.The concentrator building in 1974 contained the concentrating equipment and miscellaneous services (such as machine shop, warehouse, analytical lab). The grinding and flotation sections were divided into three circuits ('A', 'B', & 'C'). 'A' and 'B' circuits treated copper-zinc ore and 'C' circuit treated the much more difficult copperzinc- lead ore. This 'C' circuit had been modified over the years to implement improvements in the metallurgy."

Jan 1, 1979

By Marcel M. Djivre

Electromagnetic wire rope testing is the only practical non-destructive method to evaluate the current condition of wire ropes in general, and in the mining industry in particular. The method has been successfully used worldwide for decades. In mining it has considerably improved the safety of operations. Yet, problems persist. In particular both the Loss-of-Metallic-Area (LMA) readings, as well as the Local Fault (LF) readings, as obtained by different instrument operators, were found to be unacceptably diverse. Consequently, large sums have been spent internationally, as well as in Canada, comparing a whole range of these instruments in an effort to rate their performance. The published results clearly confirmed operational experience, namely that the LMA and LF readings were, indeed, unacceptably diverse. Excellent pertinent conclusions were also published. In Canada the authors? conclusion was that while the divergence in the LF signal based results could, possibly, be attributed to both hardware and human-error related factors, the LMA signal related quantitative uncertainties were human-error related. Consequently, much attention was paid in Canada to developing novel control methods, namely computerized ones to replace the more error-prone analogue ones. In addition new sensor-heads were developed, both for portable as well as for permanent installation with remote control operations. While these efforts were of considerable benefit, the situation must again be carefully reviewed with very special reference to deep-level mining, now of immediate concern in Canada as well. In this paper the authors supply an overview of the results obtained by three of the four major international projects referred to previously. Relevant conclusions/comments are also restated. Moreover, specific recommendations are put forward as to how current problems might best be remedied.

May 1, 2004

By R. J. MacLeod

"INTRODUCTIONThe removal of water or liquid from slurries and solutions is a procedure generally present in many process industries. This has prompted the development of many mechanical and thermal devices with which, I have no doubt you are al1 familiar.In the mining industry, beneficiation of ores necessitates ' the removal of water or other 1iquid from the concentrate material. The most common method of accomplishing this is by means of thickeners, vacuum filters and rotary dryers, generally all three and in that order;The use of spray drying techniques to obtain the same end has many advantages and these will be outlined here.THE PRINCIPLE OF SPRAY DRYINGA Spray Dryer consists of a cyclone shaped chamber where hot air and atomized concentrate are introduced in the upper section. (Sec figure No. 1). Efficient mixing of these two streams produce dry concentrate and moist spent air, both of which are removed from the base of the chamber.Thermal dewatering involves the product ion of heat and spray drying has no special requirements in this area. Generally a direct fired air heater is used and the products of combustion whether they stem from the use of gas, oil or coal fuel go into the spray dryer along with quench or dilution air which is used to reduce the combustion gases to the desired temperature. This generally lies in the range of 1,000 to 1,600° F. In spite of these relatively high inlet temperatures, the spray drying process eliminates the need for refractory lining or indeed any special heat resistant metals except on the air inlet ducting. Waste heat may also be used even if a significant amount of contamination is present."

Jan 1, 1972

By David Stephenson, Hugo Granados, Steven Klohn

"HudBay’s Constancia project is a copper molybdenum concentrator located in southern Peru. In 2010 Ausenco was contracted to perform a feasibility study optimization review which resulted in an improved design with significantly increased throughput capacity at a minimal increase in capital cost. Construction began in 2012 with commercial operation commencing in May 2015. This paper outlines the process plant design as well as describing the plant’s major equipment selections, start-up and early operations experiences.IntroductionHudBay Mineral’s Constancia project is located at 4200 meters above sea level (masl) in southern Peru, approximately 630 km south-east of Lima, Peru. The property can be accessed by road from Cusco, Peru, (approximately 110 km to the north), or from Arequipa, Peru (approximately 215 km to the south). Matarani, accessed via Arequipa, is the closest port.Constancia is located within the Yauri-Andahuaylas metallogenic belt. The region contains several large copper-gold-molybdenum porphyry deposits such as Antapaccay (by Glencore) and Los Chancas (by Grupo Mexico), and copper skarn deposits such as Tintaya (by Glencore) and Las Bambas (by MMG). Constancia’s ore reserves contain copper and molybdenum with trace amounts of gold and silver.Ore is mined by an open-pit operation. The process plant recovers copper and molybdenum concentrates, storing tailings in a conventional tailings management facility. Infrastructure at the site includes a grid power supply (via a 70 km overhead transmission line from Tintaya), water supply, workshops and an accommodation camp. Mine life is 22 years.Site construction works began in 2012 with first copper concentrate produced in late 2014. The project was executed for approximately 1.75B$USD.Ausenco’s design approach focussed on developing a capital efficient copper molybdenum concentrator. This paper outlines key features incorporated in the concentrator design, plant layout and equipment selection, as well as start-up experiences and early operational results."

Jan 1, 2016

By R. W. Watson, H. D. Peer

"This paper outlines the history of steel linings in the Autogenous Mills, the factors influencing the decision to convert to rubber lining, and the operating and cost experience with the rubber liners to date. INTRODUCTIONSherman Mine is an open pit iron ore mining, concentrating and pelletizing operation located at Temagami, Ontario. The operation employs 392 hourly employees and 81 salaried employees and has an annual capacity of over one million L.T. of high quality iron ore pellets produced from low-grade magnetite ore.The Sherman Mine is a joint venture; 90% owned by Dominion Foundries and Steel Limited (Dofasco) of Hamilton, Ontario, and 10% owned by the Tetapaga Mining Company, a wholly-owned subsidiary of the Cleveland Cliffs Iron Company of Cleveland, Ohio. The operation and management of the mine is by Cliffs of Canada, Limited. Development of the property was started in 1965, with pellet plant production beginning on March 17, 1968. At the present time, the orebodies contain sufficient reserves to sustain operations at current production levels for 30 years. Mining was originally carried out in three orebodies, the North, South, and West pits. The North Pit has been exhausted and mining operations ceased in the spring of 1980. A fourth pit, the East Pit, will be developed during the early 1980's."

Jan 1, 1981

"The measurement of error in assays collected as part of a mineral exploration program or mining operation historically has been undertaken in a variety of ways. Different parameters have been used to describe the magnitude of relative error, and each of these parameters is related to the standard measure of relative error, the coefficient of variation. Calculation of the coefficient of variation can be undertaken in a variety of ways; however, only one produces unbiased estimates of measurement error: the root mean square coefficient of variation calculated from the individual coefficients of variation.Thompson and Howarth’s error analysis approach has also been used to describe measurement error. However, because this approach utilizes a regression line to describe error, it provides a substantially different measure of error than the root mean square coefficient of variation. Furthermore, because regression is used, Thompson and Howarth’s results should only be used for estimating error in individual samples, and not for describing the average error in a data set. As a result, Thompson and Howarth’s results should not be used to determine the magnitudes of component errors introduced during geochemical sampling, preparation, and analysis.Finally, the standard error on the coefficient of variation is derived, and it is shown that very poor estimates of relative error are obtained from duplicate data. As a result, geoscientists seeking to determine the average relative error in a data set should use a very large number of duplicate samples to make this estimate, particularly if the average relative error is large."

Jan 1, 2007

By Ian M. F. Arnold

"Occupational health programs and their role in improving the quality of working life in the mining industry are discussed. Attention is directed to some problems peculiar to the Canadian mining industry. Factors affecting program development are reviewed, as well as parameters affecting cost-benefit analyses.IntroductionThe quality of working life in the mining industry is a more important consideration than in many other industrial environments because of the very nature of the undertaking. It was a strange paradox of the 1960s that preventive maintenance programs for machinery and equipment were well accepted, whereas the concept of ""preventive people medicine"" was basically ignored. Fortunately, there seems to be a swing toward the development of occupational health programs in many sectors of the business community; however, there is a noticeable lack of consistency and uniformity for thought among the members of the mining industry. The blame for this lack o f progress in the occupational field cannot be entirely attributed to the industry, but must also rest with (for the most part) apathetic and inadequately trained physicians. This latter problem is slowly improving with the growing recognition that a well-planned and executed occupational health program may improve the quality of working life for mining employees and their families.There are a number of factors which relate to occupational health in mining, and its effect on working life quality. Included among these are:1. Community isolation.2. High accident risks.3. Occupational disease risks.4. Production demands and the state of the economy.5. Government regulatory requirements.6. Travel demands.These, and others, reflect on all levels of the mining industry. To examine how these factors can be moderated by an occupational health program, it is necessary to first review the rationale for such a program and some of the costs related to it."

Jan 1, 1983

By John D. Campbell

"IS YOUR MANAGEMENT CONTROLLOOP FUNCTIONINGMineral processors make use of hundreds of control circuits in their mills, process plants, smelters and refineries, to optimize throughput and recovery and minimize cost. This afternoon, I would like to discuss what is probably the weakest circuit in any mineral processing operation - the management control loop.In their recent book ""The Winning Streak"", Goldsmith and Clutter describe extensive research on unsuccessful companies. They conclude that ineffective control, which does not immediately identify the problems, is one of the main failings of unsuccessful companies.We will look at the three key components of control which, from the manager's point of view, ensure that the loop is complete. These three are:• measuring what's happening,• assessing its significance, Rnd• altering performance.If we compare management control to process control as shown in this first figure, ""We see that parameter sensing by the analyzer in a process circuit is analogous to performance monitoring by management in a responsibility centre. The analyzer senses temperature, pressure, flow, weight or some surrogate indicator such as colour to indicate ion concentration. For manage1nent, the performance to rnonitor is dependent upon the objectives of the responsibility centre, and the key factors which affect these objectives."

Jan 1, 1985

By André van Wageningen

Long term mine scheduling is one of the most difficult optimization problems. The problem is said to be NP-complete in that the best possible solution cannot be found any quicker than checking all possible permutations and combinations. In current mining operations, it is important to report changes in long term plans as soon and as accurately as possible. Where geological data can change rapidly, such as in narrow vein deposits, the need to quickly identify and optimize different long term alternatives becomes a difficult task and can lead to many permutations of the long term mine plan. The question arises, is the new plan optimal or not? Can the company objectives be met while adhering to operational constraints? Although a number of optimization techniques have been used in the past, many include significant simplifications or fail to produce acceptable results within the required timeframe. Genetic Algorithms (GAs) are among the most promising optimization techniques within operations research. They are based on natural selection and evolution of solutions to complex problems. They have been known to quickly converge within a few percent of the optimal solution by examining only a fraction of the possible permutations. The GA itself contains very little problem specific information and, as such, in this study, has been linked to a discrete-event simulation (DES). The DES is able to evaluate each sequence proposed by the GA and determine the effectiveness and value of each schedule. The DES feeds information regarding the feasibility and quality of the solutions back to the GA during the optimization process. In this paper, GAs and DES are described and the coupling of the two methods is outlined. The GADES module is then used to ?optimize? a narrow vein theoretical case study and the results discussed in a broader mining context.

Oct 1, 2004

By W. J. Young, K. B. Macneill, C. N. Smith

"A BRIEF HISTORY OF THE MURRAY BROOK MINERAL DEPOSITDuring the mid-1950's intensive exploration activity in northern New Brunswick followed the discovery of the world class Brunswick base metal deposit. Using the prototypes of modern airborne geophysical and geochemical exploration techniques many mineralized areas in the Bathurst-Newcastle area were quickly identified. This base metal - silver camp is situated within the metavolcanic - metasidementary rocks of the Tetagouche Group which forms a roughly circular caldera-chaped voloanio complex of Ordivician age.One of the early results in the exploration history in the camp was the discovery of the Murray Brook Deposit by Kennco Explorations, (Canada) Limited. During routine ground checking of geophysical anomalies, most of which turned out to be graphitic schist, the discovery of some copper bearing float was made by the exploration team. This encouraged the company sufficiently to carry out a regional stream sampling program which lead to a large anomaly associated with a hematitic gossan. Diamond drilling of a weak Slingram anomaly over the gossan zone resulted in the discovery of massive sulphide lenses. This was followed in 1956-7 with an intensive drilling program. The result was the delineation of a potential ore body containing an estimated 23 million tons with an overall grade of 0.44% copper, 0.86% lead, 1.95% zinc, 25.73 g/tonne (0.91 oz/ton) silver, 0.28 g/tonne (0.01 oz/ton) gold. Within this package were higher grade zones of copper and lead-zinc mineralization approaching ore grades.A thick blanket of gossan was present and is reported to have caused the drillers considerable trouble as they attempted to penetrate it to get to the underlying sulphides. The gossan, consisting of iron oxides and silica fragments sits on top of the massive sulphides and attains a remarkable thickness of 45.5 meters (150'). Early work had suggested that the gossan was enriched in gold and silver. If this were the case and if the precious metal could be leached out with cyanide, then mining and recovering those values might be economic.With this in mind Northumberland Mines Limited optioned the property from Kennco in 1985. Preliminary leach tests indicated that indeed the gold in particular leached readily. Subsequent drilling of the gossan (using triple core barrel technology for better recovery of the easily ground core) indicated 1,536,363 tonnes (1,690,000 tons) with an average grade of 1.05 g/tonne (0.037 oz/ton) gold and 42.13 g/tonne"

Jan 1, 1993

By D. Imeson, T. Grammatikopoulos, G. Pearse, M. Aghamirian, C. Mohns

"Spodumene mineral is a source of lithium for lithium ion batteries. Thus, the production of a spodumene concentrate with an approximate grade of 6% Li2O is targeted. Traditionally, spodumene is concentrated by froth flotation using fatty acid as the collector. Amine collector can also be used to float mica ahead of spodumene as required or feldspar from the spodumene tailings. Slimes have a negative effect on spodumene flotation and they are commonly separated by scrubbing and de-sliming prior to spodumene flotation. The main losses in spodumene flotation typically occur in cyclone overflow, scrubbing slimes, spodumene flotation tailings and mica concentrate. In recent years, dense media separation (DMS) is the main concentrating process in Australian spodumene operations. In these operations, DMS is efficient at generating coarse grain concentrates and rejecting large portions of silicate gangue, thereby directly reducing the milling cost. The ore should be crushed to 3/8” or coarser while further crushing is possibly necessary on the middling particles to scalp further spodumene. The DMS feed should be classified to remove fines (typically -0.5 mm particles). The final middlings and undersize fractions could then be processed by flotation. The main requirement in DMS operations is to have good spodumene liberation at relatively large grain size. This paper reviews the most significant DMS and flotation parameters in spodumene beneficiation. The treatments of different minerals in the spodumene ore are also addressed.INTRODUCTION A number of laboratory/pilot plant programs have been recently conducted at the SGS Lakefield site, sponsored by different clients. The main objective has been to develop a process flowsheet to generate a spodumene concentrate containing 6.0% or higher Li2O (~75% spodumene) suitable for producing lithium carbonate by a hydrometallurgical process. Depending on spodumene liberation size, dense media separation (DMS) can be an attractive option to produce a final high grade concentrate and to reduce the mass to be treated in the flotation circuit. In such a case, crushing would typically be performed in stages, with DMS separation to recover a spodumene concentrate and reject gangue minerals following each stage. DMS middlings and -0.5 mm fines can be processed by flotation to further recover spodumene. In the flotation process, coarse stage grinding minimizes the grinding cost and formation of slimes. In the majority of cases, a grind size (K80) of approximately 200 microns is sufficient for flotation. After primary grinding, mica, if present in an appreciable amount, should be floated to minimize interference with spodumene flotation. Desliming after scrubbing and high density conditioning are the key process operations prior to spodumene flotation. Spodumene can then be floated from silicate gangue minerals with a fatty acid or a mixture of fatty acid and petroleum sulfonate at slightly alkaline pH. Subsequently, feldspars can then be floated from the spodumene tailings."

Jan 1, 2012

By R. D. Lindsay

"Pamour Porcupine Mines, Limited is involved in the mining, milling and primary refining of various gold, gold - copper and refractory gold ores. Pamour operates five mines in the Porcupine Mining District of Ontario, and two 2,550 t/d milling facilities.Both metallurgical facilities use conventional cyanidation technology including zinc cementation for precipitation of gold and silver from solution. The precipitation process, as applied to clarified leach solutions (less than 1 ppm suspended solids) at Pamour is called the Merrill - Crowe process. Precipitates from both milling operations are treated at Pamour's Area Refinery. Schumacher precipitates, unlike Pamour No. 1, require an ''Acid Treatment Stage"" prior to refining to remove the high contained copper. This is accomplished by leaching the precipitates initiallv with sulphuric acid to remove zinc and then with sulphuric acid and manganese dioxide to dissolve copper. Refining procedures after ''Acid Treatment"" are essentially the same for both precipitates.The following considerations highlight the basic principals applied to refining cyanidation precipitates at Pamour, including:"

Jan 1, 1986

By A. F. Banfield

"IntroductionELEMENTAL sulphur occurs in three types of deposits: in salt domes in the Gulf Coast region of the United States and Mexico, from which over 90 per cent of world native-sulphur production is obtained; in sedimentary deposits such as those in Sicily, which are thought by some authorities to contain the largest world reserves of elemental sulphur; and as surface deposits, associated now or in the past with some phase of vulcanism, the type which bas the greatest world-wide distribution.Deposits of the volcanic type are the subject of this paper.From antiquity until the successful development of the sulphur-bearing salt domes at the beginning of this century, important sulphur production for local needs was obtained from volcanic deposits in many parts of the world. Due to technical and economic factors, however, producers could not compete in price with sulphur from salt domes. •The result has been that, except in Japan and Chile, little sulphur was produced from volcanic deposits from about 1910 until the start of the Korean war in 1950. Shortly after the outbreak of the Korean war, an acute world sulphur shortage developed and prices skyrocketed in many countries up to several hundred dollars a ton. Interest in volcanic deposits was renewed and exploitation of many was undertaken. Few of these operations have been successful, mostly due to inability of management to solve technical problems.While important volcanic deposits of elemental sulphur have not been reported ( 1) in Canada, and it is doubtful that any will be found, data presented in this paper may be of interest to students of ore genesis.This paper is based on field examination of numerous deposits of the volcanic type in North and South America."

Jan 1, 1954