Search Documents

By S. Kodama, G. Sasaki, K. Matsugi, K. Sugio, Y. B. Choi

"Pure aluminum (Al) matrix composites with changing the volume fraction of TiB2 particle content from 10 to 30% was fabricated by spark plasma sintering (SPS) process. Then the microstructure, density, dispersibility and thermal conductivity of the composites was estimated. As increasing TiB2 content, the dispersibility of particles and the density of the composites degraded slightly. And, the effect of the dispersibility of TiB2 particles on the thermal conductivity was quite little. The thermal conductivity of the composites was less than the theoretical value calculated by Maxwell-Eucken equation considering the effect of the density. It is due the influence of the interface heat transfer rate, because these composites have many small sized particles and have high interface density.INTRODUCTION Recently, metal matrix composites (MMCs) have been used widely in electric / electronic components, architectural materials, transportation equipment, aerospace and a precision instruments, because it’s superior properties have been greatly watched. Demand of MMC for industrial use has been increasing gradually. Furthermore, multifunction properties are required for the composites strongly. By integrating the dissimilar materials, the composites have various properties that we cannot get from monolithic materials. On the other hand, the response to the thermal management is required for materials, recently, and the need for the structural material controlling the thermal conductivity has been increasing. Especially, superior thermal conductivity and good mechanical properties from room temperature to high temperature are required for heat sink and heat exchanger at the same time. In late years, a study on the composites combining carbon materials and aluminum and copper has been developing, and actually the composites with high thermal conductivity which is not provided in the conventional materials is developed. On the other hand, non-oxide ceramics particles such as SiC and AlN, TiB2 have good thermal conductivity. Particularly, as TiB2 has good electrical conductivity, TiB2 containing MMCs is expected as innovative materials used as electric/ electronic components. Furthermore, as TiB2 has low density, high melting point, low thermal expansion and good deformation resistance, the development of high performance composites with multi-functional properties is expected. As thermal conductivity of pure Al and TiB2 are 225 and 66.4 W/mK, respectively, it is expected that the degradation of thermal conductivity by adding dispersant in Al matrix is suppressed. The authors have carried out a thermal conductivity, electrical conductivity, mechanical properties of 20 vol.% TiB2 dispersed Al composites (Sugio, 2016, Sasaki, 2016). In this study, the influence of quantity of addition of TiB2 on microstructure, thermal conductivity was studied minutely."

Jan 1, 2018

By Michel Gauthier, Pierre Marcoux, Gaétan Morin

"The recent opening of Muscocho's gold mine at Montauban, as weil as the discovery of several new copper-gold showings of a similar nature near the confluence of the Saguenay and St , Lawrence has revealed the existence of a new metallogenic gold province which is located within supercrustal units of Helikian age within the Grenville Province. Three metalliferous belts have been identified, each one of which is related to a series of SW-NE trending faults. The first is located in southeastern Ontario and southwestern Quebec. The second extends from the Balmat-Pierrepont mining district of New York State up to the Lac St. Jean region of Quebec, and includes the Montauban camp. The third follows the St. Lawrence river in Charlevoix County and along the north shore of the Gulf of St. Lawrence.The gold mineralization which is present in the central portion of the Grenville Province is of two types: either stratiform or vein. Deposits of the first type, of which the Muscocho is the type locality, are economically the more interesting of the two. Not only is this mineralization stratiform, but also shows a distinct affinity to AI-rich, Mg-rich or calc-silicate-rich bands. As is the case with the Bousquet and Hemlo regions of the Superior Province, they are associated with layers which are rich in sillimanite and occasionally staurolite. A second parallel between the Bousquet and Montauban deposits might be the presence of manganesian gamets, which have been recognized at the two localities. Some of the mineralization in the central Grenville Province is located within thin bands of iron formation which are rich in arsenic.The stratiform gold deposits of the central Grenville Province are of exhalative origin and are located within a volcano-sedimentary terrane. It is probable that a part of the gold present in these Helikian deposits have been derived by remobilization of Archean mineralization. The vein showings form as a consequence of the remobilization of the Helikian strata during the Grenville metamorphism,"

Jan 1, 1985

By Derek H. C. Wilton

"The Cape Ray Fault Zone of southwestern Newfoundland contains two notable electrum/ base metal sulphide quartz vein lode occurrences hosted by two contrasting lithological units, viz. a graphite schist horizon and a granite. The two occurrences, although in proximity, are not in direct contact, but, based on geochronological, geochemical and isotopic evidence, they were apparently deposited from hydrothermal fluids generated as a vapour phase from the magmatic progenitor of the Windowglass Hill granite.This paper provides further evidence, from REE and background A u and Ag data, for the magmatic origin of the hydrothermal fluids. Wall rocks to the electrum-bearing quartz veins in both the schists and granite have experienced a LREE depletion probably due to leaching by Cl-bearing solutions. Gold and silver contents are typically low in all rock types but there is a slight elevation in gold concentrations in those units in contact with the Window glass Hill granite. The granite also has the relatively highest gold and silver contents of any unit in the region.IntroductionThis paper presents the evidence from rare earth element (REE) and gold/silver concentration data for the magmatic origin of hydrothermal fluids responsible for deposition of the Cape Ray electrum deposits of southwestern Newfoundland. The two deposits occur in the Cape Ray Fault Zone (Fig. I) within the Windsor Point Group and Window glass Hill granite. The larger occurrence is called the Main Shear Showing and consists of a deformed quartz vein horizon, which extends for - 6 km, within the late Devonian Windsor Point Group. This unit is an intermixed ignimbrite and mafic tuff sequence with associated schists (metasediments) and gabbros. The host rocks to the mineralized quartz veins are interleaved graphite, chlorite and sericite schists. Basal ignimbrites within the Windsor Point Group have been dated, by Rb/Sr isotopic methods, at 377 ±21 Ma (Wilton, 1983a). The basal ignimbrites also have enriched REE patterns, an elevated initial Sr ratio (0.709) and a peraluminous-siliceous nature which suggest they resulted from the partial melting of continental crust (Wilton, 1984)."

Jan 1, 1985

By Holly L. O. Huyck

Disseminated hypogene sulphide mineralization in the Lakeshore porphyry copper deposit (also called the Cyprus-Casa Grande deposit) of Arizona occurs in both a granodiorite stock and associated volcanic rocks. Structural development and vein paragenesis at Lakeshore are similar to other Laramide porphyry copper deposits of the southwestern U.S. Two major structural trends are present: intrusive contacts, copper-bearing potassic alteration veins and major post-mineralization Basin-and-Range type faults trend N-NW, whereas phyllic veins and secondary post-mineralization faults trend N-NE, and deep propylitic veins trend NE-ENE. Lithologic permeabilities, caused by fracturing in all rocks and by grain size distributions in volcanic rocks, controlled the distribution of copper mineralization. Differences in chemical compositions of host rocks did not affect are grade. Structural control, through density of chalcopyrite-rich veins, was the major control of are grade. Fracture density of other potassic vein types did not strongly affect grade. Within volcanic lithologies, permeability, as indicated by grain size distribution, provided a second-order, but significant, control of mineralization.

Jan 1, 1990

By Ibrahim Ocak

The prediction of machine utilization time and determining machine performance plays an important role in scheduling and planning tunnel excavation and data base created serve a major role in further applications. In this study, the construction methods of two twin tunnels situated between Basak Konutlari station and Istoc station are summarized. Geology in the study area is composed of fill and weak rock, respectively starting from the surface. The tunnels of 5.6 km in length were excavated with two different earth pressure balance machines (EPBM). Excavation diameters of the EPBMs were 6.564 m. The performance of the machines are analyzed and compared in order to accumulate data for further applications in similar ground conditions in Istanbul. The distance between two twin tunnels is 14 m from center to center and the EPBM in the one tube was almost about 100 m behind the other tube. Segmental lining with 1.4 m of length and 30 centimeters of thickness were used as final support. The overall performances of the two Lovat TBMs are found to be respectively as; the best daily advance rates 30.8 m/day and 30.8 m/day, the best weakly advance rates 115.0 m/day and 153.9 m/day, the best monthly advance rates 388.7 m/day and 400.5 m/day. Total waiting and maintenance times were 25.2 and 16.7 %, respectively.

Aug 1, 2013

By T. Patching

"MINING operations at the Star Key Mine provided an example of a small-scale prairie-type coal mine that employed several interesting procedures and achieved good productivity with low capital expenditures. The mine was located about 11 miles north of the city of Edmonton, on the north side of the Sturgeon River valley. It opened in 1945 and operated until 1979. Output in the winters reached about 500 tons a day in the late 1940s, but in the spring and summer periods activity was usually limited to only servicing and development work. In the later years of the mine's life sales fell to less than 100 tons per day. Most of its output was bought for domestic use in furnaces and stoves so production of large sizes was desired. A modest market for stoker coal did exist for a time. Screenings (-5 / 8 in.) were sold to the city's power plant until it converted to natural gas and were also used for thawing frozen ground for work on pipelines. These markets were comparatively small and the small sizes did not command as high a price as did the larger sizes. However the extension of natural gas services to rural markets cut into the domestic heating market and finally led to closure of the mine. The coal was strong when freshly mined, but because of its high inherent moisture content, about 25%, it did not store well on surface but tended to disintegrate. It was of subbituminous Crank with a heating value of about 8000 Btu per pound and burned with a clean flame. The seam mined was in the Edmonton Formation, of Upper Cretaceous age, at a depth of 60 to 80 ft below the surface. The seam in the mine area was about 11 feet in thickness but thinned gradually to the north and south and split to the west (1). It was approximately horizontal but gentle rolls in the floor of several feet in height necessitated brushing in places to produce suitable haulage grades. The floor material was of bone and clay, overlying a thin layer of coal. Above the seam there were only a few feet of mudstones and weak sandy shales while the remainder of the overburden was clay and unconsolidated glacial till and surface soil. Because of the soft floor and weak roof material the miners usually left about a foot of coal in the floor to provide a firm working surface and about a foot of coal above the rooms and two feet of coal above the entries to provide a competent roof."

Jan 1, 1985

By Libao Zhu, David J. Williams, Nazife Erarslan

"Statistics show that the drawbell in underground mines is usually subjected to significant damage by impact loading due to falling ore. Drawbell damage causes a large quantity of residual ore to remain on the drawbell, thus leading to a huge waste of ore resources. In this study, the Cavity Monitoring System (CMS) and Surpac software were employed to visualize the 3-D damage. Also, the Discrete Element Method (DEM) was employed to perform simulations of the falling ore to investigate the damage evolution of drawbells under repeated ore impact and obtain the dynamic damage accumulation mechanism. The reason of drawbell damage was found due to the micro-shear cracks. The numerical simulations of a drawbell damage process under repeated impact loading showed the main failure type was shear failure and this type damage was found increasing with more ore falling. INTRODUCTIONDrawbells are an important part of underground mines and play a significant role in ore recovery in terms of safety, economy and efficiency (Brunton et al., 2010; Hustrulid & Bullock, 2001; Trueman et al., 2002). In most cases, blasted ore is gravitated along the drawbell and finally arrives at the footwall of the drawpoint. However, some of the blasted oversize ore blocks clog the drawbell road and those ore pieces are called hang ups (Penswick, 1997). However, any damage on a drawbell is believed to be the reason for these hang-ups. In the literature, researchers have reported that the stability of the draw-point is influenced by the stress distribution above and near the drawbell (Butcher, 1999; Neverov & Neverov, 2013). Much research in the literature has been done on draw-points in underground mines. In fact, rockfalls cause very serious damage on a small impact area in a very short time (Volkwein et al., 2011). Hoek (2000) pointed out that the blasted ore causes progressive ravelling and even collapse of the drawpoint, thus the ore in the stope is abandoned. In this paper, the Cavity Monitoring System (CMS) was employed to obtain the damage profile of a drawbell due to the impact of rockfalls and to confirm the residual blocking ore on the damaged drawbell. Then, the drawbell damage evolution due to repeated falling ore was simulated by the Discrete Element Method (DEM)."

Jan 1, 2015

By John Porritt, Alain Dorval

"TioMin Resources Inc. is evaluating the feasibility of exploiting the heavy mineral sands deposit at Natashquan on the north shore of the Gulf of St-Lawrence, Quebec. TioMin holds the exploration rights to 180 square kilometres, on which 1.6 billion tonnes of sands grading approximately 6% heavy minerals were outlined. The heavy minerals of value include magnetite, ilmenite/hematite, garnet, and zircon. An important part of this evaluation is the development and testing of a mineral separation flowsheet. Under a comprehensive mandate from TioMin, the Centre de recherches minerales (CRM) provided technical assistance to build and operate an on site primary concentrator pilot plant. This plant produced a 93 tonne concentrate, providing over 60 % heavy minerals. This concentrate was shipped to the CRM pilot plant in Quebec City. It was used for further flowsheet testing and for preparation of products and concentrates of heavy minerals with regard to marketing possibilities. This paper presents the flowsheet developed to produce these concentrates.IntroductionIn late 1992, an 11 tonne bulk sample of sand was collected from within the mineralized zone of the Natashquan deposit. This sample was processed over conventional spirals and wet tables at the pilot plant facilities of the Centre de recherches minerales (CRM) in Quebec City. A primary concentrate was produced, from which several 20 kg samples were forwarded to five research laboratories in North America and in Australia. Their tasks were to determine the mineralogical composition of this concentrate and the potential for recovery of marketable minerals from the heavy mineral sands. Satisfactory results obtained from this approach encouraged TioMin to proceed with a more detailed pilot plant program."

Jan 1, 1995

By DAVID C. MILLER

Barite deposits occur worldwide and in a variety of geological environments. In recent years, several deposits of barite and barite-lead-zinc have been discovered in northern British Columbia, Yukon Territory and Alaska. Most are associated with Devonian-Mississippian age sediments, and many are syngenetic, bedded-type deposits. The Mel is a barite-lead-zinc deposit; it lies within Lower Cambrian strata and appears to be of epigenetic replacement origin. Figure I is an aerial view of the property from the south. Observations herein described are based largely upon field work, megascopic studies and two recent B.A.Sc. theses (Biasucci 1979, Rennie 1979).

Jan 1, 1984

By A. Jafarnia

Aluminum alloys are frequently grain refined during solidification in order to promote the formation of an equiaxed grain structure in the casting. The application of Ti-based grain refiners and/or Ti containing master alloys for improving mechanical properties may result in formation of Al-Ti based intermetallics. Although the grain refinement produces many desirable qualities in aluminum castings such as improved castability and mechanical properties, the addition of Ti to Al-Si foundry alloys may lead to the formation of some undesirable intermetallic particles such as AlTiSi and cause a number of operational problems such as nozzle blockage due to segregation and agglomeration of aluminide particles within the nozzle. There are several questions to be clarified when minor amount of Ti is added to Al-Si alloys. They include nucleation and growth of AlTiSi particles, their morphologies and orientation relationships with aluminum matrix and the dissolution of these intermetallics during the course of solidification and/or post solidification treatments. The current study was initiated to study the process and possible mechanism of aluminide dissolution and the related phenomena such as segregation and agglomeration. It reports the results found during reheating of laboratory prepared Ti-added A356 alloy at three temperature ranges of below solidus, mushy zone and above liquidus.

Jan 1, 2004

A Joint Venture between Hope Bay Gold Corporation and Miramar Mining Corporation recently acquired the Hope Bay project in Nunavut, which represents the first discovery of a major new Archean greenstone gold belt in Canada since the discovery of Hemlo in 1982 and the Yellowknife belt in 1938. Located some 685 km North of Yellowknife, the Hope Bay Belt is geologically comparable to the other major gold producing regions of Canada. The initial discovery of gold mineralization in 1992 led BHP to acquire virtually all of the Hope Bay belt. Over the subsequent 6 years, BHP expended C$85 million on exploration, including 180,000 meters of drilling, 2.3km of underground workings and a 27,000 tonne bulk sample, as well as extensive environmental and economic studies. Hope Bay Gold and Miramar acquired the Hope Bay property in December 1999 for a cost of C$27 million, considerably less than the C$85 million spent by BHP in exploring the property. They both hold 50% of the project, and share expenses equally. Hope Bay Gold is the manager of all exploration phases and Miramar will manage feasibility, construction and operations. The Hope Bay Joint Venture controls 1,117 sq. km., covering virtually the entire 80 km long Hope Bay and adjacent Elu greenstone belts. We believe that Hope Bay is one of the best-undeveloped gold projects in Canada. Work to date has defined a global resource in excess of three million ounces of gold in three principal deposits, each of which is open to extension along strike and to depth. A C$17 million work program for year 2000 focused on advancing a significant portion of the gold resource to a measured and indicated category. This will provide the basis for initiation of a feasibility study in 2001. The 2000 drill program was one of the largest undertaken in Canada last year, and is a clear indication of our confidence that Hope Bay will develop into a major gold producing district. The majority of the potential mineable areas known to date lie within 350m of surface and would be accessed through a combination of open pit and declines. Currently, development of a 1,800 to 2,000 tpd gold mine producing in excess of 300,000 ounces of gold per year at cash costs below $US200 per ounce is envisioned. In addition, the exploration potential on the 80 km gold belt at Hope Bay is clearly tremendous.

May 1, 2001

By J. M. Turnbull

THE primary objective of the young graduate, after the war, will be to obtain a suitable position within the Industry, with adequate pay and opportunity to advance. The positions available to meet this demand will depend on the magnitude and organization of the industry. The size of the mining industry, in particular, will depend on a number of factors, including depletion; new discoveries of mineral deposits; beneficiation of new kinds of mineral deposits, based on research; technical improvements, also based on research, enabling the mining of lower grade deposits; and complex social factors. The organization of the industry will depend on its control and management, which may be greatly affected by social conditions and changes, and may include a wider or a narrower use of technical services. The corresponding training or qualifications of graduates, to meet these conditions, calls for a consideration of educational requirements and facilities in relation to the conditions that are likely to occur. Some forecast of the probable future of the Industry, after the war, based on consideration of. the above factors, is necessary as a basis of discussion, since the graduate must find his place in the industry of that time, and find his work in maintaining and improving it, within the existent social framework. Social factors are pressing and? important at present and their future impact is uncertain. In considering these, a few quotations and extracts may be in order. "A new economic order, based on free access to the sources of raw materials, means free use of the world's wealth by all civilized nations" (The Pope. Also advocated by Churchill and Roosevelt in the Atlantic Charter). "Every citizen should have a voice in the conduct of business or industry which is ?carried on by means of his labour" (Archbishop of Canterbury).

Jan 1, 1943

By C. Gordon Saunders

"The ungraded-fibre mill is located at the mine site and has a rated capacity of 6,600 tons of ore input and 1,200 tons of ung1•aded fib1 •e product per day. Power for operation is obtained from a diesel generating plant located on the site, which has a capacity of 5,300 kW. The preliminary milling process consists of prima1•y and secondary crushing, drying and temporary storage of plus-1 1h -in. material. The final milling processes are two stages of crushing and three stages of screening, with air-lift separation of the fibre from the host rock. The central mill building also houses a machine shop, mill maintenance shops, a mobile equipment overhaul shop, an engine and majo1•-component overhaul shop, and a warehouse. Major changes to the milling ci1•cuits since start-up have been the addition of a larger secondary cone crusher, ct third dryer, adding a rotary distributor to the feed of the screening section and adding an automatic start-up sequence for all equipment except crushers and fans. The operation of the mill is coordinated from a central control room, where a ""mimic"" panel indicates the operation of all major units in both the ore preparation and the screening sections. Product quality is controlled by continuous sampling and frequent labo1•atory analysis, which provide data fm• the adjustment of aspirating hoods and mill feed rate. Operating problems unique to this location, and common to a sub-arctic environment, are discussed."

Jan 1, 1976

By Walter Koellner

Today?s large electric mining shovels are significant users of power and represent peak loads of more than 3.5 MW to a mine?s distribution system. The power swings during normal operation can influence the line voltage at the Point of Common Coupling (PCC). The static converters for the shovel?s motions also create voltage and current harmonics which are fed back into the mine?s power grid. In addition, shovels themselves are affected by the power quality of the mine?s distribution system. This paper introduces the use of active IGBT rectifiers, also called Active Front Ends (AFE), as alternative to conventional, line commutated SCR thyristor rectifiers. The AFEs convert the AC line input into a controlled DC-link voltage. This DC voltage is then used as input to IGBT inverters, which power the AC motors of the shovel?s Hoist, Propel, Crowd, and Swing motions. The introduction of AFEs creates the following operational improvements: i) reduction of the Harmonic Current Distortion THDi from more than 40% to less than 4%; ii) full regenerative operation; iii) the potential for line voltage stabilization at the PCC; iv) high tolerance for line voltage fluctuations; v) improved dynamic performance, and, as result vi) higher availability and productivity of the shovel.

May 1, 2001

By S. Nakamura, K. Fujiwara, S. Hirosawa, S. Tsukamoto, Y. Koshino, Y. Aruga

"In this study, hardness test, differential scanning calorimetry(DSC)and transmission electron micros copy were carried out to investigate the age-hardening behavior of Al-Mg-Si alloy with a Mg+Si concentration of 1.5mass%, and a Mg/Si ratio of 1.0. Pre-aging treatment was conducted for the solution-treated and then water-quenched specimen at 100, 80, 60, 40, 20 (natural aging), 0 and -20°C for 20min or 5h, followed by artificial aging at 170°C for 20min. It was found that when pre-aging time is prolonged from 20min to 5h, the bake-hardening response is deteriorated irrespective of the pre-aging temperature. In particular, the specimens subjected to pre-aging at 20-40°C for 5 h hardly increased the hardness with the subsequent artificial aging. From the results of DSC measurement, it was suggested that as pre-aging temperature is lowered, the amount of solute clusters formed during pre-aging, i.e. Mg-Si clusters and Si-rich clusters, is decreased, but the ratio of Si-rich clusters is increased, resulting in the deteriorated bake-hardening response.INTRODUCTIONIn recent years, Al-Mg-Si alloys have been widely used forautomotive body panels due to their excellent characteristics such as high strength-to-weight ratio and good formability. Their strength is increased not only by artificial aging during paint-bake treatment; i.e. “bake-hardening”, but also when kept at room temperature(RT);i.e. “natural aging”, in association with the suppressed bake-hardening response. Such a “negative effect of two-step aging” has been a serious problem because Al-Mg-Si alloy coils are unavoidably maintained at RT in the manufacturing process of body panels; e.g. shipping and storage. However, it was reported that pre-aging above 70°C before the two-step aging can restore the bake-hardening response, and such an improvement is related to the formation of solute clusters(Sato, 2006; Abidet al., 2010; Takaki et al., 2014; Zandbergen et al., 2015). From the comprehensive analysis by three-dimensional atom probe (Aruga et al., 2014 and 2015), it is believed that Mg-Si clusters formed during pre-aging transform into the strengtheningß"" phase, whereas Si-rich clusters formed during pre-aging act as a detrimental precursor of ß""phase. In this study, it was aimed to investigate the effect of pre-aging conditions, especially pre-aging temperature and time, on the formation of solute clusters during pre-aging, in order to elucidate the mechanism of the age-hardening behavior of an Al-Mg-Si alloy."

Jan 1, 2018

By A. Gakwaya, P. Vachon-Joannette, P. Gagnon, J. Lévesque

"Predictive numerical methods are essential tools for reduced development cost and improved high performance designs of modern aircrafts. Their use leads to savings in terms of design cycle time and experimental trials. Composite materials subjected to impact loadings demonstrate various damage modes such as matrix cracking, fiber breakage, delamination and, ultimately, fabric fracture. Composite laminates are extensively used in the aerospace industry, and their damage modeling is complex due to their inhomogeneity and anisotropic behavior. Damage evolution affects both in-service properties and performance of these composites. In this work, the drop-weight impact test has been simulated. Using a material model that accounts for both delamination and intralaminar damage, laminates response is analysed using numerical simulations based on 3-D finite-element models of the commercial code Abaqus/Explicit. Experimental and simulation results are compared, in terms of energy absorption and contact force. The obtained numerical results show good agreement with experimental data.INTRODUCTIONAs primary aircraft structures are increasingly being made from advanced fiber-reinforced polymer matrix composites and are in general exposed to a variety of impact scenarios (bird, hail, debris etc.), an understanding of the impact event and the performance of composite materials during impact is important in the development of new structures. This work is focussed on low velocity impacts that typically occur when foreign objects hit the aircraft during maintenance or other on-the-ground operations. These impacts can cause non visible damage that affect the structural integrity of the composite components. While for metallic structures, damaging impact events typically leave noticeable dents due to plastic deformation, in contrast, for high strength carbon fiber reinforced composites, they can deform elastically to strain levels exceeding 1% and the internal damage can often occur without the formation of a visible dent. The identification and effect of impact damage on the performance of the structure is thus of great concern to the aircraft industry as the durability and damage tolerance of these composite structures are strongly influenced by the size of detectable internal damage."

Jan 1, 2016

By Arnfinn F. Prugger, Fritz F. Prugger

"The Saskatchewan potash beds are overlain by a number of water-bearing formations. There are water zones in the footwall as well. These aquifers created difficulties during the construction of shafts to the potash beds at 1()(}() m depth, and they pose a continuous threat to the safe and efficient operation of potash mines in the province.The first shafts to be sunk in Saskatchewan encountered major problems during shaft sinking. Of the 17 potash shafts started in the province, five had major water inflows during shaft sinking or after production startup, and one was abandoned because of water problems. The biggest obstacle encountered during shaft sinking was a poorly consolidated sand-shale-clay-siltstone unit commonly called the Blairmore Formation, which occurs at a depth of about 500 m. The initial problems with shaft sinking were overcome in the 19605by using European methods of freezing and the installation of cast-iron tubbings or a double-steel lining through water bearing horizons.From the start of production in the early 19605, operators have been aware of the ever-present hazard of potential water inflows into mine openings from permeable units in both the hanging wall (carbonates of the Dawson Bay Formation which occur 15 m to 50 m above the mining level) and the footwall (carbonates of the Winnipegosis Formation which occur 50 m to 150m below). This awareness has been reflected in conservative over-all extraction rates and mining layouts specific to local conditions. In spite of this consciousness, a number of water problems have occurred in operating mines. These have resulted in everything from simple increases in expenditure to the shut-down of one mine in 1987.In this paper a history of water problems in the Saskatchewan potash industry is given, followed by a summary of measures that are now commonly used to avoid these problems. A description of each inflow event is given, and the attempt is made to analyze the causes of each occurrence. Based on what was learned f rom each event, suggestions are made to prevent future water inflows into potash mines."

Jan 1, 1991

By T. Winkler

This paper presents elements of the Virtual Working Environment for identification of hazards occurring in the mining industry. The Virtual Working Environment includes models of machinery and models of anthropometric features. Examples are given for identification of technical hazards at the design stage using the following computer programs: Finite Elements Method, Multibody System Analysis and Human Body Modeling. One of the methods to improve work safety at the machine and equipment maintenance stage is to share design and operational knowledge in a form of an Interactive Electronic Technical Manual (IETM). An IETM is created using so-called reusable knowledge elements connected by relationships. A metamodel created in Unified Modeling Language is one of the forms for description of these relationships. The metamodel can represent, for example, interrelations between elements of repair procedures. Examples of procedures realized during the replacement of a damaged cutting bit are presented and discussed.

Aug 1, 2013

By Ken G. Kress

Syphons can be a simple, reliable and proven alternative to otherwise more complex pumping systems or low level outlet works. In a simple form they consist of a pipeline constructed over the top of an embankment or high topographic feature, connecting a source pond to a receiving pond or channel (see Photograph 1). The syphon action is initiated by removing air from the pipeline (priming) using simple devices which can be purchased ?off the shelf?. Once primed, the syphon flow rate can be controlled or stopped using conventional gate, valve, orifice plate or other devices. Repriming is not required even if the flow is stopped, provided the syphon is not drained. A limiting factor in considering a syphon as a design option is the maximum lift (i.e., vertical distance from source pond level to summit of syphon) which is approximately 9 metres, or less, dependent on syphon pipe features and site conditions. Pipeline syphons can be quickly constructed from readily available materials including steel, polyethylene and PVC pipe. They are particularly well suited to many of the unique conditions often encountered at minesites. This paper identifies situations that can sometimes be best resolved using pipeline syphons. It provides basic principles for pipeline syphon design and includes case histories of their successful application.

May 1, 2001

By J. Huh

Recently, there is growing trend to build the high-rise and install curtain walls. Following this trend, we developed robot for building wall cleaning work, which moves along Built-in guide rail of building. Because it moves attached at building wall for cleaning work, it can be seriously affected by potential threats, like earthquake, strong wind, malfunction, and construction error of built-in guide rail. In order to cope with those threats actively, this paper presents the Fail-Safety system. The building wall cleaning robot consists of two moving system: The Horizontal Moving System which mainly do maintenance work, and The Vertical Climbing System which transport the horizontal moving system floor by floor. We apply the Fail-Safety system to these systems. The Fail-Safety system consists of sensors to detect external situation, and, with information of sensors, give instruction for what to do. This robot system is installed with four kinds of sensors: shock sensor, infrared ray sensor, laser sensor, magnetic sensor. First, shock sensor detects external shock during cleaning work. When shock sensor detects big shock, the robot returns to starting point to inspect how damaged it is. Second, infrared ray sensor detects damage of built-in guide rail. It is to prevent destruction of robot caused by moving along damaged rail. Third, laser sensor gives notice about where obstacle is. It is for robot to avoid crash with obstacle and decrease damage. Fourth, magnetic sensor detects magnetic points, which are installed in rail at regular intervals, and helps robot to find its position, based on location of magnetic points detected. If robot is damaged by external shock and its encoder, which gives information of location to it, is not working, magnetic sensor will give information of robot?s location to robot. And then, robot regulates its velocity depending on position of it, and safely returns to starting point. The Fail-Safety system in this paper is for building wall cleaning robot to sense external threats, and prevent getting worse. Applied to this active protection system, making safe environment of maintenance work is possible for robot system.

Aug 1, 2013