Search Documents

"Coupon testing has been used to investigate stress corrosion cracking (SCC) of rockbolts in a laboratory based experimental program. This program has focused on the use of ASTM G39 three- and four-point bent beam coupon specimens, immersed in an acidified sodium chloride test solution containing hydrogen sulfide. The specimens were loaded to a range of stresses from zero, to just above the materials yield strength. It was found that only specimens above an applied stress of 580MPa failed by means of SCC, showing that rockbolts loaded to near their yield strength may be susceptible to SCC in-situ.INTRODUCTIONStress corrosion cracking (SCC) is a failure mechanism that affects material through the growth of hairline cracks when exposed to a corrosive medium while under stress (Jones and Ricker, 1999). SCC has been found to affect rockbolts in the Australian underground coal mining industry and has the capacity to cause the catastrophic failure of ground support systems, potentially leading to falls of ground in underground excavations, injury or death to mine personnel, damage or loss of equipment, and loss of productivity through the loss of roadway access (Crosky et al, 2002).Coupon testing utilises small scale samples that are intended to be indicative of the behaviour exhibited by a material in-situ (ASTM G39). The small scale, and usually high surface area to volume ratio of coupon specimens mean that they corrode at faster rate proportional to their mass, greatly reducing testing times. The small scale of the specimens allows them to be more easily prepared and handled, loaning them to mass manufacturing techniques.A previous study conducted by Vandermaat et al (2012b) into the use of three- and four-point coupon testing in-situ in an underground coal mine failed to result in SCC of the specimens. This paper serves as a follow up laboratory investigation in order to understand why these specimens did not fail. Previous studies into the SCC in rockbolts carried out by Gamboa and Atrens (2003) determined that rockbolt steel has a critical stress threshold of approximately 90% of the material ultimate tensile strength (800-900MPa). This study will focus on this critical stress threshold as a possible explanation for the lack of failure in the in-situ specimens (Vandermaat, 2012b)."

Jan 1, 2015

By Jean-Pierre Birat, François Hanrot, Gérard Danloy

Global warming presents an enormous challenge to the steel industry, which is both carbon-intensive and energy efficient. Lean production can provide some short-term emission mitigation, at the level of the Kyoto requirements. In the middle term, more use of scrap will also help alleviate emissions. But to reach much larger reductions in GHG emissions, on a par with the likely targets that will be set after the Kyoto period, the steel industry will have to imagine new production paradigms, which constitutes its most formidable challenge for the years to come. Carbon capture and sequestration, processes leaner in carbon use, electricity and hydrogen from green sources will have to be added together in a patchwork of process routes, which will have to be developed at great risk in the next decade, hopefully through broad international cooperation.

Jan 1, 2004

By Y. Obara, A. Sato

"Limestone is one of the most important mineral resources, and in Japan it is only one mineral which can be fully supplied by the domestic product. Generally limestone mines in Japan located at mountainous regions, and the combination between bench-cut method and the carry-out system using vertical shaft is widely used in the domestic mines. During mining operations, the occurrence of the blockage in the vertical shafts is very serious problem. Once the blockage in the shafts is occurred, a lot of works and dangerous procedures are necessary to solve the problems. It is thought that blockage is influenced by the cohesion and friction coefficient due to clay minerals thrown into the vertical shafts, however, the quantitative and precise reason is not revealed yet.In this study, the process of blockage occurrence was simulated by 2-Dimensional Discrete Element Method (DEM). In the 2D-DEM analysis, discontinuous circular particles are generated, and the individual movement of each particle is calculated by forward difference method. In the analysis, several typical ore distributions are applied, and the DEM analysis was conducted under the various combinations of cohesion and friction coefficient. From analytical results, it was found that the friction coefficient strongly influences to the occurrence of blockage and there were a threshold values which blockage does not occur. Several kinds of shaft shape were also simulated towards different ore size distributions, and those influences to the blockage occurrence were also discussed."

Jan 1, 2015

By L. Jiang

The evolution of twinning in an AM30 Mg alloy was examined by uniaxial tension and compression testing at temperatures from ambient to 250°C and a strain rate of 0.1/s. The samples were cut along the extrusion direction from extruded AM30 Mg alloy tubes. Specimens deformed to various strain levels were examined by optical microscopy and electron backscattered diffraction (EBSD) techniques. The results indicate that the initial extrusion texture plays an important role in the formation of different types of twins and that the twinning behavior also depends on the strain path. Contraction and double twinning are the dominant twinning mechanisms in uniaxial tension, while extension twinning prevails in uniaxial compression. The different twinning behaviors are shown to be responsible for the sharply contrasting strain hardening characteristics of the experimental flow curves.

Jan 1, 2006

By M. A. Roche

The property of the Hudson Bay Mining & Smelting Company, Limited is located at Flin Flon lake, 85 miles northwest of The Pas, Manitoba, on the Manitoba-Saskatchewan boundary. The area is at latitude North 54°, and is approximately 1,000 feet above sea level. The ore-body occurs in amygdaloidal greenstones, which are to be referred to the earliest basic volcanic flows in the district. It was discovered in an outcrop on a point of land jutting into Flin Flon lake, and subsequent diamond drilling proved that it extends under the lake both to the north and south of the point of discovery. After the taking of soundings from the ice during the winter months, it was estimated that l,000,000 tons of overburden, mainly mud and clay, would have to be removed to expose the underlying ore. Flat diamond-drill holes indicated that the ore-body was separated into more or less independent lenses by horses of unmineralized greenstone, and that in places the overall width, including horses of waste, reached 450 feet. These several] conditions were the main factors influencing the management in their decision to adopt an open-cut method for the mining of the upper portion of the ore-body. Before it was possible to commence stripping operations, it was necessary to dam-off the eastern portion of Flin Flon lake, instal pumps, and de-water the dammed-off area. Dams for this purpose were constructed of mine waste rock and clay filler from nearby hillsides. Material for the bottoms of the dams was taken across Flin Flon lake in hopper-bottom barges. Trestles were then built on the dam bottoms and dams were complete by the time trackage was available. De-watering commenced in April, 1930, and was completed by the latter part of May of the same year. Estimated pump output for the period was roughly four billion gallons. Two Morris 10-inch dredging pumps were used, direct-connected to 250 h.p. electric motors. Individual pump capacity was rated at 3,000 g.p.m. against a 150-foot head. Average head for the operation was 50 feet, which increased the total output considerably. The pumps were mounted on floating barges in cribbings of piling driven at the lowest points in the lake bottom.

Jan 1, 1933

By C. Gaubert, G. Bourassa

"The construction or rebuild process in the anode baking furnaces has been modeled with the software Rockwell Arena, in order to minimize the process cost and risk. The case study was focused on the sectional rebuild (""on the fly"") that needs a high coordination of the material inventory, the on-site personnel and the construction/production schedule. Multiple entities and resources were allocated for the different part of the process (in-furnace process, prefabrication, materials transportation, etc.). Logic flow charts and VBA macros were used to simulate the space utilization (including cranes utilization) and interaction with production. MS-Excel output files can show user-friendly results."

Jan 1, 2006

By T Salman

The construction and use of the B.E.T. (gas adsorption) apparatus is described. Examples are given for the determination of large and small surface areas using nitrogen and krypton. Introduction A NY study of the milling of ores from crushing to grinding, classification, and concentration and finally dewatering of the products involves solid particles which are either in contact with a gas or a liquid phase. The surface area of the solid and its characteristics constitute important parameters in all mineral dressing operations. The success of any particular operation is dependent on the interaction of the surface of the solid particles with the gas or the liquid phase. Particle size and specific surface (surface area per unit weight) continue to be important parameters in the flotation research associated with the adsorption of collector molecules or ions on mineral particles, as in the early years of mineral dressing research (1). In order to understand the mechanism of the flotation process, it is essential that the surface properties of the adsorbent be known.

Jan 1, 1965

By M Safa

Addressing deficiencies and defects that occur during construction projects is costly and time consuming. The manual quality assurance programs currently used in the industry have certain limitations, including human error and lack of consistency. Hence, there is a need for integrated electronic models that employ new technologies and methods. This research introduces an integrated construction quality control system that has the potential to improve quality management processes in the construction field for piping construction, which is a complex process often requiring rework. The proposed integrated system relies on data collected from construction sites using photogrammetry and laser scanning, which is then used to compare actual work performed to that designed. The proposed system aims to improve the promptness and accuracy of quality assurance processes, in particular dimension measurements, by avoiding human error and integrating defect detection and quality management. The use of this system has highlighted some of the limitations during data fusion and acquisition process, which are highlighted in this paper. These aspects must be considered to increase the reliability of the acquired information.

Aug 1, 2013

By A. Poor Zaeif Doost

With columns being installed in rougher section at Miduk Copper Complex, the rougher feed mainly reports to rougher-scavenger cells. To evaluate the efficiency of regrinding circuit, we conducted flotation experiments on samples of the feed and the products of the regrinding circuit. The grade difference of these products at 85% recovery was considered as the efficiency index. Results show that, with weight recovery of the rougher-scavengers the efficiency of the circuit increases. Exclusion of the rougher-scavenger concentrate from the feed to the regrinding circuit, resulted in an increase in the efficiency index from 10.12 to 17.6%.

Jan 1, 2012

By E. Demedde

Carbon anodes in aluminium reduction cells are continuously consumed during electrolysis. In prebake cells the anodes are replaced at regular intervals. The spent anodes, called butts, are often allowed to cool in air while emitting fluorides into the building from the hot alumina cover and the adhering bath. In modem smelters spent anodes are placed inside enclosures and fluoride emissions during cooling are effectively reduced. Fluoride emissions from spent anodes were estimated by considering the kinetics of fluoride formation, a heat transfer analysis of the cooling anode butt and the ventilation flow from a cavity. Fluoride emissions from large anode butts cooling inside enclosures were compared with those cooling in air. Good agreement with published experimental values was obtained for enclosures having different leakage opemngs, when a hydrofluorination reaction of the spent anodes was included.

Jan 1, 2006

By R. A. Payant, J. A. Finch

Under certain conditions of air and moisture, sulphide materials can spontaneously heat, or selfheat. The reaction mechanisms of self-heating are not well understood. Most previous work has involved pyrrhotite because it is the most reactive sulphide. The current work investigates the self-heating behavior of sulphide mixtures composed of sulphides other than pyrrhotite. The four studied sulphides were pyrite, chalcopyrite, sphalerite and galena. The rest-potential was measured for each. Binary mixtures formed as a 1 : 1 weight ratio were pyrite-galena, chalcopyrite-galena, pyrite-chalcopyrite and chalcopyrite-pyrite. The four sulphides and the binary mixtures were subjected to standard self-heating tests. The four individual sulphides did not self-heat. However, mixtures of pyrite-galena and chalcopyrite-galena with rest-potential difference (?E) >0.3 volts did self-heat while the mixtures of pyrite-chalcopyrite and chalcopyritesphalerite with rest-potential differences (?E) = 0.1 volts did not self-heat. The results demonstrate that when certain non self-heating sulphides are combined they can self-heat. A possible explanation based on galvanic interaction and formation of hydrogen sulphide as an intermediate product is discussed.

Jan 1, 2009

Fault detection and identification are major challenges in process engineering and manufacturing and the key component of abnormal event management systems. Timely detection, diagnosis and rectification of abnormal or faulty process conditions can lead to savings of billions of dollars in equipment damage and lost productivity, not to mention the prevention of injury and loss of human life associated with industrial accidents. A major contributing factor to current losses in industry is the reliance on human operators to interpret high-frequency samples from hundreds or thousands of variables simultaneously. As a result, the automation of fault detection and diagnosis is seen as crucial to the successful implementation of abnormal event management, the need for which is becoming all the more urgent given the increased complexity associated with modem industrial plants. In this paper, a methodology for process monitoring that uses support vector methods to extract nonlinear features from data is discussed and applied in the diagnostic monitoring of an industrial liquid-liquid extraction column.

Jan 1, 2005

By T. Kagawa

Ever-increasing demands for non-ferrous metals owing to population growth and improvements in the standard of living in the world, under the constraint of limited availability of natural resources, would easily make us imagine that more efficient and sustainable developments in mining and smelting activities are required in the near future with due consideration for environmental concerns. In order to realize the efficient and sustainable development of mining and smelting activities and operations, the following issues are indispensable: (1) to investigate the up-to-date pollution control technologies of mine and smelter, (2) to promote those technologies, (3) to develop technologies which are environmentally friendly. This paper discusses the recent technologies for environmental conservation/prevention and their diffusion in the world, and also the key technologies required for the most desirable sustainable development.

Jan 1, 2007

By Jr. Wilkinson

Suncor Energy currently mines approximately nine hundred thousand tonnes of ore and waste per day at its open pit operations in the Athabasca Oilsands near Fort McMurray, Alberta. Modeling these deposits for planning purposes is particularly challenging given the characteristics associated with the deposit - stratigraphic deposition coupled with gradational grade distribution. The identification of ore and waste is a combination of bitumen cutoff grade, minimum mining thickness and separable waste thickness subject to criteria established by provincial regulatory agencies. Suncor along with Mincom Inc. have collaborated on this project to derive a methodology, automated by computer software, to streamline the ore and waste identification process. This paper explains the methodology and programs created to identify ore and waste in use at Suncor Energy and how this identification is used to categorize reserves and to generate mine design surfaces.

Apr 1, 2005

By Jean Descarreaux

"The Rexspar uranium deposits are located near Birch Island in central British Columbia. The property lies within the Omineca crystalline belt of the Cordilleran Orogen. Gneiss, schist, tuffaceous and porphyritic trachyte are the main rock types encountered on the property. These rocks are of pre-Late Triassic or probable Mississippian age.Lenticular bodies of mica and pyrite-rich rock are the host of three closely spaced uranium deposits and are found close to a fluorite deposit. The altered trachytic rock as well as the fluorite and uranium deposits are found in the upper part of the trachyte unit. The latest tonnage estimates are 1,441,820 tonnes averaging 23.46% CaF, for the fluorite deposit, 490,966 tonnes of 0.084% U10afor the 'W' deposit, 164,290 tonnes of 0.074% UP8 for the ""B"" deposit and 459,124 tonnes of 0. 071 o/o UP8 for the ""BD"" deposit.A hydrothermal replacement origin was first proposed for the fluorite and uranium deposits. The mineralizing and altering solutions would have been genetically related to a felsic batholith outcropping a few kilometres south of the property. Another hypothesis has been proposed more recently. A volcanic centre has been tentatively identified in the upper part of the trachyte unit, close to the mineral deposits. The fluorite and uranium deposits could possibly be volcanogenic, rather than related to the Cretaceous felsic batholith.IntroductionFluorite and uranium mineralization occur on the property of Consolidated Rexspar Minerals and Chemicals Ltd. in central British Columbia. The exploration and development works executed over the years are summarized in this paper. The deposits and their geological environment are described but the origin of the mineralization has not been definitely established."

Jan 1, 1986

By A. G. Pentland

PROSPECTING is popularly supposed to be surrounded with an air of romance and adventure. The word 'prospecting' brings to mind high mountains, northern lakes, and aeroplanes. A note of urgency has been added to this by the war, particularly in the case of strategic, minerals. Prospecting for strategic minerals in a modern mine in full production, although it may Jack the romance of travel in little-known places, has the advantage of having all the necessary machinery at hand and ready to go into action at a moment's notice. HISTORY Tin was discovered in the Sullivan ore in 1925, when a white streak was noticed on a pilot table which was being used to check the amount of galena in the tailing. The mineral which made up this streak was identified as cassiterite. The amount of tin in the ore is so small that, while of scientific interest, it was considered to be of very little economic importance. Nevertheless, several attempts were made to learn something of the occurrence during times when other work was nor pressing. These studies were dropped when anything came up that seemed more important.

Jan 1, 1943

By F. Q. Barnes

"Uranium, thorium and yttrium have been recovered, since the 1950s, from pyritic quartz-pebble conglomerates occurring in the basal sediments of the Quirke syncline at Elliot Lake. Gold, an element of interest in similar type deposits occurring worldwide, is a very minor constituent of the Elliot Lake conglomerates because the provenance area of the sediments had few gold-bearing rocks.Uranium, thorium and rare elements are found in resistate and diagenetic minerals occurring in the matrix of the conglomerates. The valuable elements are recovered from the acid soluble minerals during the milling process.Large uranium reserves occur in mines found on both limbs of the Quirke syncline. Major reserves are being developed on the South Limb of the syncline, where the Stanleigh Mine, among four past-producers, has been reactivated.IntroductionUranium and thorium commonly occur in anomalous amounts in coarse basal sediments. Radioactivity in basal conglomeratic sediments is generally attributable to resistate minerals, that rarely occur in concentrations high enough to be of economic significance. One type of basal conglomerate found worldwide, in Precambrian cratonic basins, has uranium or uranium and gold concentrations large enough to be of economic interest. Principal among the occurrences are the pyritic quartz-pebble conglomerates of the Huronian in Canada, of the Witwatersrand in South Africa and at Jacobina in Brazil.The uranium and gold mineralization of these conglomerates was derived from provenance areas where both elements occurred and were later concentrated through source degradation and deposition in placers in a reducing environment. Only the Huronian conglomerates, generally much richer in uranium but with negligible gold, have been exploited solely for their uranium content.The uraniferous conglomerates of the Huronian at Elliot Lake, 500 km north of Toronto, continue to represent a major world source and supply of uranium concentrate."

Jan 1, 1986

By S. Ivanova

The results presented in this paper show that the gold solution dilution is a key parameter to control the dispersion of gold on ?-Al2O3 the selected support. The variation of concentration leads to changes in pH which modify the nature of gold complexes from HAuCl4 formed in the solution. These complexes are presented. Some of them (AuCl3(OH)- and AuCl2(OH)2 -) react with the surface of alumina and give interesting interaction. AuCl2(OH)2 complex has been considered as an ideal complex because of the strong anchorage of a bidentate species on the alumina. This complex is formed mainly in a solution of gold with a concentration of 10-4 M giving a pH of 3.5-4.5. The nature of the anchorage and the amount of chlorine, has an influence upon the formation of Au-Cl bridges which modify the dispersion of the gold on alumina of the final catalyst as shown by TEM.

Oct 1, 2003

By S. Shairp

Copper is an impurity as well as a necessary reagent in the processing of zinc sulfide concentrate at Hudson Bay Mining & Smelting Co., Limited's (HBMS) zinc pressure leach plant. Copper is present in the zinc concentrate as chalcopyrite, which consumes reagents necessary for zinc leaching. A small percentage of copper precipitates in the autoclaves, discharge lines, and flash tanks, requiring maintenance of the equipment and disposal of the solids. Copper also precipitates in the neutralization stages and is removed to low levels in a specific copper removal stage of purification. Yet some copper, as copper sulfate, is required, along with potassium antimony tartrate, in the final purification stage to improve cobalt removal from the zinc sulfate solution prior to electrowinning. The behaviour of copper experienced at HBMS's zinc pressure leach plant is discussed.

Jan 1, 2008

By V. H. Valenzuela

Materials in process or in stocks are quite relevant items in almost every plant, particularly in mining operations, where efficiency in rate of recovering material of interest becomes a key issue when production costs are evaluated. A manager requires information to do an effective use of the resources, especially when raw materials are involved. Losses associated to leaking, efficiency in the transformation process, performance of equipment, and operating conditions are a short list of items which must be properly identified and evaluated. Operations supervisors require information in order to keep key process variables under control. Because of these information needs, it is absolutely necessary to carry on a series of activities related with installation and maintenance of measuring equipment, sampling equipment, sample preparation, chemical analysis, statistical analysis, data handling and reports generation. These pieces of data must be managed on a wise manner in order to get the most of it, keeping always on mind data reliability. Normally, information related with metallurgical balance and even more, the metallurgical balance concept, is handled under an accounting criteria which does not allow dealing with the real world. This situation happens because the criteria utilized do not consider aspects such as bias and uncertainty associated with every measurement that affect the quality of the information and therefore conclusions drawn from it. The purpose of this paper is to give a few rules, necessary to follow, in order to develop an adequate Metallurgical Balance System for an operational point of view. The Gaussian approach for error propagation is used as a basis, allowing one to know the actual uncertainty of the balance and the way how it can be improved. A few real applications of this concept are listed, detailing experiences obtained from practice.

Jan 1, 2007