Search Documents

By O. Neves, C. G. González Beca, M. C. Sol Pereira, H. Sousa Vale, R. A. Guedes de Carvalho, M. N. Sampaio

"As sulphide ores are usually concentrated by flotation , the material is very finely ground <37um), wet and impregnated with the chemicals used in flotation. These conditions are favourable to the development ofchemical reactions which are largely influenced by atmospheric conditions (temperature, humidity, wind, etc.) as well as by the geometry of the piles.Physical and chemical properties of a chalcopyrite concentrate were determined by laboratory tests. The knowledge of these properties was considered necessary in order to establish a correct design of the storage and handling operations of the sulphide ore concentrates obtained by flotation.The properties studied in this work were: transportable moisture limit, flowability, effects of vibration, hygroscopicity, ""caking"", chemical alterations by humidity, oxidation and self-heating (auto-ignition, dry and wet oxidation, self-heating by humidification and its prevention).INTRODUCTIONIn order that the handling and the transport of a powdered material may be carried out correctly, it is necessary to know certain physico-chemical characteristics. Transportable moisture limit (TML), apparent density (both aerated and compacted), compressibility, angle of repose, angle of spatula, cohesion and angle of slide(l-4) are characteristics (among the flowability parameters) worth knowing.Moisture content of the powdered material is fundamental, because if this is too low heavy losses will occur when the product&apos;s particle size is very small, if it is too high, separations between solid and liquid phases may occur. In the latter case, the centre of gravity of the system may change suddenly and cause accidents, mainly if transport is by sea or by river."

Jan 1, 1989

By E. Yan, M. Mankosa, E. Wasmund

"Rougher flotation in sulfide ore applications is typically performed using conventional flotation machines. The trend over the last 100 years has been for these cells to become larger in volume with cells reaching sizes of 600 m3 and in some cases even larger. The associated foundation loadings, transport and installation requirements along with building size have also increased. In an economic environment where projects must be executed with dwindling capital supply, bigger is not always better. More recently, industry is being challenged to identify new technology that allows for improved flowsheets and financial returns through efficiency gains. To meet this challenge, a novel high-intensity two-stage flotation system known as the StackCell™ was tested to potentially achieve installation volume and required retention time gains when compared to conventional flotation circuits. The results from on-site pilot scale work conducted on typical copper concentrator rougher flotation feed showed retention time gains on the order of 6 to 9 times when compared with conventional flotation equipment. This finding has the potential of reducing capital demands for rougher flotation circuit designs when incorporating the StackCell. The results from test work will be discussed in this paper showing comparative test data generated with a Denver bench batch test, pilot StackCell and large conventional cells, all receiving the same feed.INTRODUCTION Over the last few years, a number of flotation devices have been described as two-stage or multi-stage flotation units. The idea behind multi-stage flotation devices is that flotation performance can be improved by utilizing cells with multiple specialized units in series, but not all units of the same type, as is practiced in trains of multiple tank cells or columns. Instead, each unit is specially designed to provide the optimized fluid environment for each stage of the sequential flotation process. This idea has been proposed based on a study of the fundamentals of the flotation process, and the realization that the process consists of discrete sequential processes, that are each optimized with dissimilar process conditions (Finch et al, 1995), (Zhou, 1996). Instead of executing each step simultaneously in a homogeneous fluid environment, where the conditions would be a compromise between particle collection and froth recovery, the multi-stage flotation unit operates in a set of segregated process environments, each with a set of conditions optimized for that step."

Jan 1, 2018

By Lauri Gregg

The implementation of Energy Management within the global mining industry has advanced significantly during the past 20 years. Consequently, the industry?s knowledge of energy efficiency improvement opportunities, more energy efficient technologies, renewable energy technologies, energy procurement practices, and most importantly, practical approaches for integrating the energy management best practices into business processes and operational procedures has improved greatly. Based on 25 years of experience leading the management of energy in mining operations and the Canadian mining community, the author discusses the key building blocks in the evolution toward becoming an energy efficient mining facility. Sustainable energy management depends on the internalization of the behaviors related to the effective energy use by a mining organization. The paper outlines the typical business drivers that stimulate top management commitment to allocate the resources necessary for this to happen. It also explores the barriers that mining companies must overcome to maintain the commitment. Additionally, it will advocate the need for the application of the principles of organizational change management as part of the energy management implementation process. The question regarding how energy management can be made to happen in a way that is practical for an established organization is answered by providing the details of the framework for energy management, the methodology for controlling energy use, and the roadmap for integrating energy as a key business parameter and production process input variable. An Energy Management System standard developed within the Mining Association of Canada?s ( MAC ) Towards Sustainable Mining ( TSM ) initiative has played an important role in increasing the capacity of the Canadian mining industry to manage energy. The impact of the application the MAC TSM Energy/GHG Management Protocol by Canadian mining companies will be discussed. In June of 2011, the international ISO 50001 Energy Management Systems standard was finalized and published for use. The structure of ISO 50001 will be outlined along with its applicability to the mining industry. Opportunities for practically improving mining energy performance along with the most appropriate current new technologies will be identified. A brief discussion of case studies will be included that demonstrates the successful implementation of Energy Conservation Measures ( EAC?s ) and economic benefits. In conclusion, thoughts on important areas of research and development related to increasing mining energy efficiency will be provided.

Aug 1, 2013

By Raymond B. Hryciuk

Environmental auditing has evolved rapidly over the last decade — first in North America, then Europe, and most recently in Asia — into a widely practiced discipline designed to provide senior management with assurance that operations are being managed in compliance with established governmental standards, internal company policies, and good industry practices. This paper first examines the evolution of environmental auditing, focusing in particular on three interlocking driving forces: company initiatives, collaborative industry initiatives, and government initiatives. Characteristics of effective audit programs, those that have emerged among the leaders, are discussed, including: objectives, scope, coverage, approach, staffing, and organizational considerations. The author then addresses important future trends and developments for environmental audit program design, content, and coverage.

Jan 1, 1996

By Donald P. MacKinnon

"This paper is a commentary on selected trends within the transportation industry.In general, innovations are taking place within all modes of transport (road, rail and water) serving the industrial minerals industry which will affect future distribution patterns, methods and costs. Significant technical innovations in the transportation of solids by• pipeline will also appear, perhaps in the near future, permitting the transport of specific commodities, including some industrial minerals. However, the timing and magnitude of the commercial exploitation of solids pipelines are heavily dictated by marketing factors and distribution system logistics, as well as by the innovations likely to take place within competitive modes of transport. Competitive technological developments will include increased ship capacities, improved bulk-handling facilities, larger and specialized bulk-handling rail equipment, unit trains, containerization, larger ""off-highway"" vehicles and greater inter-modal integration. Equally significant are some ""soft-ware"" techniques such as the growing interest in total distribution cost concepts. However, the impact of the developments will not be spread uniformly over all Canadian industrial minerals."

Jan 1, 1967

By J. A. Pigott, R J. Hall

The International Nickel Company of Canada, Limited operates five underground mines on the rim of the Sudbury Basin in the northern part of the Province of Ontario. Four of the mines, the Frood-Stobie, Creigh-ton, Murray and Garson, are located on the south range of the basin with-in a radius of IO miles of the centre of the city of Sudbury. The fifth mine, Levack, is on the north range about 30 miles northwest of the city. The ores are mined primarily for nickel and copper, and the principal minerals are pentlandite, chalcopyrite and pyrrhotite. In 1960 the total ore production was in excess of 16 mil-lion tons, 95 per cent of which was produced from the five underground mines and the balance from the Frood-Stobie Open Pit. Mining at this open pit is nearing completion and underground production has been expanded to replace the open pit tonnage.

Jan 1, 1961

By V. Falmagne

The mining sequence at Noranda?s Bell-Allard mine calls for two mining fronts retreating toward a central pillar known as the Retreat Zone between pyramids A and C. It is clear from numerical modelling and rock mass characterization that the induced stress level in the pillar will exceed the rock mass capacity. A mining plan was developed including the re-dimensioning of stopes in the Retreat Zone, additional ground support and instrumentation in order to ensure the safety of the workforce and to maximize ore recovery while minimizing production delays. The mining strategy consists in allowing the rock mass to fracture and fail progressively while maintaining control of the existing openings with the appropriate support. A systematic analysis of rockbursting and caving hazards was conducted for all accesses and stopes in order to plan ground support and instrumentation needs.

Apr 1, 2004

By Z. Zhang

Aluminum boron carbide particulate reinforced composites have found new applications in nuclear industry due to their special capability to capture neutrons, Recently, Alcan successfully developed a liquid metal mixing process to fabricate Al¬B4C metal matrix composite instead of powder metallurgical technology. In the process, titanium is added into the composites to control interactions between boron carbide particulates and aluminum matrix, To understand the effects of titanium on the composites, the solidification microstructure of Al-16%B4C without or with titanium was examined by optical and electron microscopes. The results show that titanium can improve the uniformity of the particulate distribution within aluminum matrix if the titanium content in the composites is more than 0,5%, Furthermore, it is found that the layer with rich titanium on the surface of the particulates can limit the formation of AlB2 type compounds, which may greatly deteriorate the fluidity of the composites, In addition, it is also found that the amount of the reaction products in the composites increases with the increase of holding time. However, the rate of the increase is mitigated by the increase of the content of titanium in the composites. Besides, a procedure was proposed and implemented for the evaluation of uniformity of particulate distribution within aluminum matrix.

Jan 1, 2005

By E. Mohammadi Zahrani

In this study, Mg-doped fluorapatite (Mg-FA) nanopowders were prepared through a sol-gel, technique and characterized. Designated degree of Mg2+ ions incorporation into the apatite structure was indicated by the x value in the general formula of (Ca10-xMgx (PO4)6F2), where x=0, 0.25, 0.5, 0.75, and 1. XRD, AAS, FTIR and TEM techniques were utilized to characterize the synthesized nanopowders. In vitro bioactivity of the powders was evaluated in simulated body fluid. Powders had a crystallite size less than 100 nm. It was concluded that Mg-substitution could alter bioactivity and dissolution behaviour of Mg-FA. These two parameters were proportional to magnesium content of the powders.

Jan 1, 2010

By Fathi Habashi

Poland has a unique copper industry. Copper sulphide concentrates are smelted in six shaft furnaces to produce matte and in a flash furnace directly to blister copper. Anodic slimes from electrorefining are treated by a modern technology to recover the precious metals. INTRODUCTION Poland&apos;s copper industry began in 1950 when the old and relatively small mines Lena and Konrad, located in Lower Silesia, were drained and recommenced production. In 1957 the industry entered a period of rapid development with the discovery of a rich ore body in the vicinity of Lubin and Polkowice which was the basis for the establishment, in 1961, of the Copper Mining and Smelting Combine (KGHM). In 1991 the Combine was restructured into a state-owned, joint-stock company under the new name of KGHM ?Polska Miedz? (KGHM ?Polish Copper?). It consists of three mines, three smelting and refining plants, and one rolling mill, and produces about 4% of the world?s copper and about 7% of the world?s silver.

May 1, 2001

By James F. Kelly

"Research and development on the production of liquid fuels from coal is rapidly expanding worldwide. AImost every industrialized country is engaged in coal liquefaction research and process development. In Canada, the federal government, through CANMET, is actively supporting coal liquefaction research and development in a number of areas.A review of the basic principles and some of the processes in the production of liquid fuels from coal is presented with reference to the characteristics of the Canadian coal resource base. An overview of the CANMET coal liquefaction contract program is presented and specific results from the batch autoclave studies carried out with Saskatchewan lignite and Nova Scotia high-volatile bituminous coals are discussed. The development of a laboratory-scale continuous-flow coal liquefaction unit at the Energy Research Laboratories of CANMET to investigate the co-processing of coal and bitumen/heavy oil is also described.IntroductionThe CANMET coal liquefaction program is made up of two interrelated parts. The first part consists of the research and development work being carried out at the Energy Research Laboratories near Ottawa, Ontario. The second focuses on contracted research and development as part of the Coal Conversion Program of Energy, Mines and Resources Canada. The long-term objective of the liquefaction program is to contribute to Canadian liquid fuels production through the definition, research, development and demonstration of different coal liquefaction technologies for the Canadian marketplace.In coal liquefaction, the main objective is to produce liquid hydrocarbons with a higher hydrogen-to-carbon (HIC) ratio than the coal feedstock while reducing heteroatom (S,O,N) content, removing mineral matter and minimizing gas production. Typical atomic HIC ratios for a variety of Canadian fossil fuels are shown in Figure I. Canadian coals have about 500/0 of the HIC ratio present in tar sand bitumens and heavy oils and only about 20% of the ratio available in methane. In general, the cost of synthetic fuels production is related to the cost of hydrogen and, therefore, to the increase of HIC ratio between feedstock and products. On this basis, the production of liquid fuels from coal would be expected to be more costly than liquid fuels produced from bitumens and heavy oils. However, for mined tar sands and some heavy oils this difference tends to be offset by the large sand content (>90 mass %) of tar sand bitumens and the increased production costs of viscous heavy oils. For example, it can easily be shown that for equal weights of distillate <525°C) yield, current coal liquefaction processes required between two and three times less mined coal by weight than the mined tar sand s required for the most technically advanced processes proposed for bitumen upgrading."

Jan 1, 1981

By J. A. Finch

"This paper describes major technical developments in rod mill design and operating practice since its introduction into the North American minerals industry over fifty years ago. The basic operating characteristics of the wet, overflow rod mill are described, and significant operating variables are reviewed in terms of their effects on mill power draw, power efficiency, and practical aspects of circuit operation. Key factors for improving the economic performance of rod milling circuits are identified. IntroductionThis paper summarizes the findings of a detailed review of available technical information on the operation of rod mills. One of the basic problems in historical comminution testwork has been the lack of a standard measure of circuit performance. The Bond Operating Work Index, not introduced until after 1950, has proven of immeasurable value in this regard, but first has to be carefully considered in terms of its utility and limitations. Its prescribed use is described in a later section of this paper.During this review, it became apparent that rod mill performance is generally not well understood. Because of combined interactions, the effects of different operating variables may be difficult to assess, and even at times appear erratic. It is obviously difficult to rationalize plant testwork or circuit adjustments when the results are highly unpredictable. The purposes of this review, therefore, were:a) to establish what basic facts have been learned about rod mill performance;b) to define some genera l guidelines for efficient rod mill design and operation; and,c) to establish a basis for specific recommendations for plant tests or adjustments with minimum risk, and maximum potential for circuit performance improvement."

Jan 1, 1986

By L. Yacher

Most metallurgical plants already have sophisticated control systems as well as a process-historian that manage thousands of real-time and historical variables. There exists a huge potential for operational improvement through the inference of patterns, correlations and cause-effect relationships within these records. The ability to run online and offline advanced multivariate statistical analyses represents a great potential for the mining industry, in various areas such as cathode quality improvement in an SX/EX plant, the analysis of the correlation between the ore characteristics and the mill throughput, the determination of early failure alerts for major equipment, etc. The background theory is described, as well as some practical experiences of operations in Chile and Peru. Cu2007

Jan 1, 2007

By Derek E. McBride

"Exploration work in the Beardmore - Tashota area has led to a reinterpretation of relationships between gold mineralization and the geologicalevolution ofthe area. The host volcanic rocks form two parallel volcanic belts connected by a much smaller cross-cutting band, which trends northeast from Beardmore to Tashota. This connecting band consists of mafic and felsic volcanic, plus clastic sedimentary rocks in a sequence conformable with the contact of the Onaman Lake Batholith to the east. A metamorphic aureole or incorporated xenoliths are lacking along this major contact and the only intrusive relationship observed is chilling between mafic dikes and a cold host granite in proximity to it. Granite dikes are totally lacking in the volcanic succession, or the overlying sedimentary sequence. A major part of this sequence consists of a polymict basal conglomerate with granite boulders and volcanic clasts in a fine-grained chloritic matrix. The nearest source for these boulders is the Onaman Lake batholith.Gold mineralization in significant economic quantities (+ 50 000 ounces) occurs at the top or above the mafic volcanic succession as quartz bands. In the Northern Empire Mine, the band is conformable, folded, boudinaged and the mineral zoning shows a relationship to variations in the host rock, not structural overprinting. In general, where the host mafic tuff is medium-grained, the quartz band is thicker, up to a metre wide, and carries economic grade; where the tuff is finer-grained and bedded, the band is very thin and low grade.Stratigraphic control and metal zoning shows that the mineralization formed as part of the development of the volcano- sedimentary succession. The other major deposits in the area (Leitch and Sturgeon River) have a similar structural history suggesting that they are also syngenetic in terms of the stratigraphic development. Regionally, these deposits were emplaced prior to any significant tectonic deformation but at the end of the mafic volcanic event.The mafic activity was related 10 a period ofextension which caused the volcanic troughs to develop along centres of rifting. The hiatus at the end of this event permitted extensive hydrothermal systems to form and deposit siliceous exhalite bands within sedimentary or terminal mafic volcanic environments in promixity to major thermal sources. Subsequently, the Kenoran Orogeny deformed the entire succession into upright folds with a sub-vertical schistosity. Evidence shows that the deposits have remained intact since deposition."

Jan 1, 1987

By W. G. Q. Johnston, J. S. Fox

"A semi-continuous belt of Aphebian magnesian extrusive and related sub volcanic rocks has been delineated by the authors over a distance of 150 kilometres in the central La Ronge lithostructural domain in Saskatchewan. They range in composition from peridotite to basalt and attain true thicknesses of up to 800 metres. For the most part, they are confined to a basal position in the La Ronge/Wasekwan metavolcanic sequence, and appear to have been extruded onto sialic crust. However, at Lynn Lake, Manitoba, in the eastern continuation of the domain, similar rocks seem to be found only at a relatively high stratigraphic level.Although metamorphism seems to have obliterated any quench textures that may have existed in these rocks, ultramafic pyroclastics, pillows and amygdules as well as intercalated, fine-grained clastic sediment attest to the volcanic nature of these rocks. Bulk chemical analyses indicate that these rocks are heterogeneous, with komatiites, tholeiitic picrites and even rocks with some of the characteristics of boninite all being present. The close temporal and spatial relationship of ""boninites"" and komatiites in the belt may suggest a high degree of Aphebian mantle inhomogeneity in the domain.Nickel-copper mineralization has been found in differentiated tholeiitic stocks within the La Range domain (e.g., at Lynn Lake), but none has yet been found in the ultramafic volcanics. However, the tholeiitic picrites do host one economic gold deposit - the Agassiz Mine at Lynn Lake .Because of the depleted nature of their mantle source, the ""boninites"" of the domain are not considered to be likely hosts for mantle-derived nickel sulphide mineralization. However, the opposite is true of the komatiites, and this points to the need for whole-rock geochemistry in setting priorities for nickel exploration in the belt. In contrast, all of the magnesian rocks of the domain probably have the same gold potential. Inasmuch as the geophysical response to gold mineralization in the domain is likely to be unpredictable, lake-sediment geochemistry, followed by base-of-till and/or alteration oriented lithogeochemistry, should be emphasized during gold exploration."

Jan 1, 1981

By R. A. Horn, S. M. Telfer

"Canada has a per capita GDP second only to Japan among the G7 countries and a positive trade balance which ranks third among the world&apos;s major economies. International trade represents a very large part of the national economy and as a proportion of GDP is larger than that of all the other G7 countries with the exception of Germany. On the negative side the Canadian current account deficit relative to the size of the economy is significantly worse than that of all major industrial countries, due mainly to the cost of servicing an immense foreign debt and to a large and worsening negative trade balance in manufacturing.The outflow of money may be reduced by increasing the productivity and competitiveness of those sectors of the economy in which Canada already has a leading competitive position and which have the potential for further growth. The mining industry is uniquely qualified in this respect in that Canada is the western world&apos;s largest producer of metals and mineral products and has the geology and the exploration skill to replenish reserves assuming that an adequate level of investment is maintained. In 1989 the minerals industry contributed $8 billion to the country&apos;s balance of payments and with the exception of forestry is the only sector of the economy which has shown consistently increasing foreign earnings over the long term.In recent years there has been a decline in exploration in Canada and a significant increase in countries such as Chile. The demand for hard currency to finance the development of the newly emerging capitalist economies of the CIS and Eastern Europe is also driving these countries to seek foreign investment to allow them to exploit their natural wealth more efficiently. Canada is therefore facing growing international competition for risk capital and in the future its trade surplus will probably decline in the face of lower cost foreign production.Canada rightly exercises a high level of environmental control on its mining operations; however a significant deterrent to investment is the fundamentally unjust application of the many provincial and federal environmental laws, under which a mining company, even if it takes every measure to protect the environment, runs the risk of eternal and unlimited future liability. If this situation is not rectified the effect will be an increase in global pollution as mines in countries with more lax application of law and regulations controlling environmental damage replace those of Canada. Tax benefits and incentives are a more efficient means than arbitrary regulations in minimizing environmental damage."

Jan 1, 1994

By A. F. Matheson

"The Jellicoe is the most westerly mine in the Little Long Lac area with a record of gold production. The property is largely covered with overburden and the ore deposit was found by diamond drilling along the projected strike of a gold bearing zone at Magnet lake 1 ½ miles to the east on the property of Bankfield Consolidated Mines, Limited. In 1940-41 Jellicoe mined the whole orebody of approximately 14,000 tons, recovering 5,620 ounces of gold.The vein is in light-coloured greywacke. A mile-long dyke of fine-grained quartz feldspar porphyry 5 to 10 feet in width lies 100 feet south of the vein. A similar, even longer dyke lies 700 to 800 feet north of the vein. Some narrow diorite dykes are also rather closely associated. The porphyry dykes are gold bearing, but not ore. The vein material is quartz and silicified and brecciated greywacke. Mineralization consists of native gold, pyrite, arsenopyrite, and some sphalerite."

Jan 1, 1954

By Ron H. Derammelaere

Coal Slurry Test Pipeline and First Recorded Commercial Pipeline Wallace Andrews founder of New York Steam Company awarded patent for ?Method of Transportation? that involved pumping finely divided coal in slurry form built test facility at Madison Avenue and East 58th Street in New York City died in 1899 in a fire and coal pipeline work was not continued First recorded commercial coal slurry pipeline designed by Gilbert Bell in 1914 to move coal from barges on the Thames River in London to a powerhouse in 8? tubes (660 yards long)

May 1, 2013

By William F. Caley, A. MacKinnon, P. W. Kingston

"The purpose of this paper is to identify a number of currently available opportunities for exploration and/or mine development in the industrial minerals field in southeastern Ontario. The paper is not intended as a complete review of the industrial minerals industry in southeastern Ontario, but highlights what are seen by the authors as areas where there are immediate opportunities for investment and growth.Traditional exploration targets in the Grenville Supergroup in southeastern Ontario have been vein-hosted gold deposits, industrial minerals, and base metals. In recent years, emphasis has increasingly shifted to industrial minerals, in response to changing technologies in the minerals-consuming manufacturing industries, and to an increasing awareness of the industrial mineral potential in this area.This paper examines the resurgence of interest in exploring for and developing a wide variety of industrial minerals, and it examines the work the Ontario Ministry of Northern Development and Mines has done under the current Canada-Ontario Mineral Development Agreement. Specific development opportunities are identified in various commodity areas. Use oj the industrial minerals wollastonite and nepheline as substitutes for fluorspar in the formulation of synthetic steelmaking slags is also discussed."

Jan 1, 1990

By C. R. van Staal, L. R. Fyffe, J. A. Winchester

"The geochemical characteristics of Early Paleozoic volcanic rocks are used to establish the following tectono-volcanic regimes in the northeastern mainland Appalachians: foreland continental rift volcanics; fore-arc ophiolites; island-arc volcanics; back-arc ophiolites; and back-arc ensialic volcanics. A Late Precambrian calc-alkaline magmatic arc bounds the Early Paleozoic volcanics to the southeast.The Precambrian calc-alkaline volcanics of the Caledonian Highlands, primitive Cambro-Ordovician oceanic-arc volcanics of the Eastern Townships, and within-plate Ordovician volcanics of the Miramichi Highlands can be related to a progressive change in mode of subduction from compressional Andean-type in the Late Proterozoic to extensional Western Pacific-type in the Early Paleozoic. The development of marginal oceanic basins in the Paleozoic created a more favourable environment for volcanogenic sulphide deposition, particularly in back-arc areas.The influence of tectonic setting is reflected in the distribution, size and metal ratios of the massive sulphide deposits associated with the volcanic rocks; deposits within intra-oceanic arcs in the Eastern Townships of Quebec average two million tonnes grading 2.2% Cu, 4.0% Zn, and 0.6% Pb, whereas those within a back-arc, ensialic rift near Bathurst, New Brunswick, average nine million tonnes grading 0.6% Cu, 5.4% Zn, and 2.2% Pb."

Jan 1, 1990