Search Documents

By Shoma Sinha, Nirmal K. Sinha

Deformation in a material at any temperature is known to consist of two major components - a reversible (elastic) part and an irreversible part (often called plastic). What is not universally known is the fact that at high temperatures greater than about 0.4Tm, where Tm, is the melting point in Kelvin, the reversible part includes not only elastic but also a delayed elastic (recoverable but time dependent) component. A very simple computational model is presented here for a constant-strain stress relaxation test (SRT) on the basis of a three-component constant-stress rheological equation derived from strain relaxation and recovery test (SRRT) data. It is shown that the rapid stress reduction during the early periods of relaxation when the stresses are high is governed primarily by delayed elasticity irrespective of the imposed strain level. This is in contradiction to the popular concept prevailing today. The asymptotic approach to a quasi-stable stress rate at longer times and lower stresses is, however, controlled by viscous flow (power-law creep). The validity of the theory is examined by comparing the predictions with experimental results obtained for a titanium-base alloy Ti-6246 at 0.45Tm.

Jan 1, 2004

By Michio Okada

Dissociative adsorption of hydrogen (deuterium) on thin gold films grown on Ir{111} surface has been studied with temperature-programmed desorption using a quadrupole mass spectrometer and nuclear reaction analysis. Thin Au{111} films are epitaxially grown on Ir{111}. Surprisingly, H2 (D2) can dissociatively adsorb on these Au{111} films, although it is well known that Au surfaces are noble enough not to dissociate hydrogen molecules [B. Hammer and J.K. Nørskov, Nature 376, (1995) 238]. We attribute this to the sensitivity of hydrogen to changes in the local surface properties, e.g., electron localization (the narrowing of the s-band, the s-band center model), which could explain the upto now unexpected high for the reactivity of a thin Au{111} surface. Moreover, we found that H (D) atoms can be confined into a Au thin film and/or the interface between an Ir surface and the thin Au film. We demonstrate how anomalously reactive thin Au films grown on an Ir surface are, and also compare the Au films with Ag films grown on Ir to test the validity/generality of our proposed s-band center model.

Oct 1, 2003

By C. V. Deutsch, O. Babak, J. G. Manchuk

High levels of geological heterogeneity occurring over relatively short distances pose a challenge to the unconventional open-pit techniques used in oil sands mining. There is strong motivation to mine selectively and minimize dilution and loss; however, the large equipment and high mining rate used to meet production targets tend to reduce selectivity. A numerical model is developed to account for geological complexity, mining equipment, regulatory criteria, and other operational parameters. This framework is used for more accurate forecasts, optimization of equipment, and other operational decisions. An example demonstrates the approach in light of Alberta Energy Regulator criteria.

Jan 1, 2014

By Patrick Fantin

Mining ? The Past Safety Not a priority; Health Not a priority; Energy Manual Labour; Horsepower? Literally. Financially Robust For the Owner?s; Mining ? The Future Safety Zero Harm Health Understanding and elimination of Industrial Disease Energy Efficient use of energy through technology. Full value of renewable energy. Financially Robust Continually build shareholder value through optimum CAPEX/OPEX.

May 1, 2013

Safety Leadership The management and leadership of a mining operation is a challenge at all times. The pressure to make production, safety, and environmental goals is intense. At some point mining cycles will put every operator into periods of time where economic issues seem to over-ride all other concerns. This is when leadership is most needed.

May 1, 2009

By J. C. Ingles

"A new technique is in the process of revolutionizing inorganic chemical analysis. Galled atomic absorption spectrophotometry, it combines the use of a special light source, a flame, and the equipment of conventional spectrophotometry, to provide a quick, reasonably accurate method for the determination of a large number of elements.This paper outlines the principles on which it is based, describes the commercial instrumentation"" available for exploiting it, and. summarizes current applications in process metallurgy."

Jan 1, 1966

By M. Okada

Consumption of refined copper in Asia, especially in China and India, has soared, and the copper price is at its historic height. New smelters and refineries have been built in the region with state-of-the-art technology to meet the unprecedented demands. Supply of copper concentrate, on the other hand, has fallen short of the growing demand for concentrate by the smelters and refineries with expanded production capacities. The shortage of copper concentrate is attributable to the delay in the mining development, caused by the prolonged price slump of before 2005. The mismatch between supply of concentrate and smelting and refining capacities may cause disorderly movement of copper price, and hamper the sound development of the industry. The recent high copper price may prompt substitution with alternate materials. With electrical and thermal conductivity and workability, copper is one of the most customer-friendly materials. It is regrettable for both customers and suppliers if the high copper price would become an impediment to promoting copper use. Some outdated and environmentally unfriendly facilities still operate. In view of recent lower-grade copper concentrate with higher sulfur content, these facilities must reform their equipment to environmental-responsive one. The current level of per capita consumption of refined copper in Asia shows that the demand of copper will further grow. It is necessary to realize stable supply of refined copper and stable copper price, to help developing countries including China and India to economically take off. Hence, it is essential that the development of the copper industry be accompanied by environmentally friendly facilities, and harmoniously increased capacities between mining and smelting and refining.

Jan 1, 2007

By Robert B. Parsons

"As the 1981 annual reports of Canadian mining companies one by one see the light of day, it becomes clear that softer metal prices and rising costs are the main problems which beset the industry today. These problems are certainly not lightened by that familiar monster lurking in the shadows-taxation! Recent taxation trends in Canada, and the existing tax regimes for the mining industry, continue to be a major bugaboo.This examination by ""Tax Notes"" of the impact of current taxation trends on the mining industry is based on a speech delivered recently by Robert D. Brown, senior tax partner of Price Waterhouse, Canada, to the annual meeting of the American Institute of Mining, Metallurgical and Petroleum Engineers in Dallas.IntroductionThe purpose of this paper is to tell a story-and it is a story with a moral. The first thing to recognize is that, with depressed metal prices and weakening western economies, high taxes, in and of themselves, are not really the cause of the Canadian mining industry's present doldrums. However, the character and level of mining taxes in Canada has had a profound influence on the development of the industry over the past decade, and the expectations of what the future holds for mining men in Canada will equally play an important role in the future development of the Canadian industry. Our tax system has, in the past, served as a negative and destabilizing influence in the mining industry: it has contributed to a major short-fall in investment commitments and hence in the contribution which the mining industry can make to the Canadian economy, and the adverse effect on the industry of previous high marginal tax rates was made far worse by the confusing, contradictory and perverse nature of the tax system itself."

Jan 1, 1982

By K. Shikaze

"For the last three years (1967-9) the value of the output of mineral resources in the Province of Ontario exceeded one billion dollars per year. To produce this great wealth, it was necessary for the mining industry in Ontario to dispose of an estimated 80 million tons of waste mill tailings. Some of these tailings were returned underground but the greater proportion was disposed of above ground in lakes, watercourses, marshy areas and in engineered impoundment basins. This volume of tailings, if accumulated in one location would cover an area of 1000 acres to a height of almost thirty feet. The provision of proper disposal of the waste mill tailings in a manner such that they will not create problems in the environment is one of the costs which must be borne from the extraction of such a wealth from our mineral resources. It is principally the potential water pollution which may occur as a result of the indiscriminate discharges of waste mill tailings which is of concern to the Ontario Water Resources Commission.ONTARIO WATER RESOURCES COMMISSIONThe Ontario Water Resources Commission was formed in 1956 and operates under the Ontario Water Resources Commission Act. The Act has been broadened and amended many times by amendments."

Jan 1, 1970

By R. W. Seedsman

In 1984 and 1985, two 7.6m diameter TBM tunnels were driven from the Donkin-Morien peninsula in Nova Scotia to access the Harbour coal seam. The design of the ground support was based on identifying zones of rock failure through the application of the Hoek Brown failure criterion and the early use of finite element analyses. In 1992, the mining project was abandoned and the tunnels allowed to flood. Monitoring data from the tunnel was subsequently used as a case study in the development of the concepts of brittle rock behaviour. In 2007, the tunnels were pumped out as part of a feasibility study into the reintroduction of longwall mining into the coalfield. There is a good match between observations of the collapse zones in the roof and sides of the tunnel and a simple elastic analysis using brittle parameters, a spalling limit of 5, and a low independent shear modulus. The brittle analyses form the basis of the design for the resupport of the tunnels.

May 1, 2009

By Lawrence Devon Smith

The Business Case for Sustainable Development ?What are SD & TBL? ?Investment Funds & Fund Managers ?Banks and Risk Aversion ?The Dilemma of Juniors ?Meet Your New Partners ?The Cost of Problems ?The Cost of Delays Sustainable Development ?Humanity has the ability to make development sustainable -to ensure that it meets the needs of the present without compromising the ability of future generations to meet their own needs.? Our Common Future BrundtlandCommission, 1987

May 1, 2003

By I. S. Thompson

"The discovery of low-grade copper-silver mineralization near the town of Tipperary, Ireland, by Gortdrum Mines Limited was the result of reconnaissance geological and geochemical exploration followed by target delineation from induced polarization surveys.Initially, orientation studies at the Tynagh lead-zinc orebody showed that such deposits could be readily detected in stream sediments and soils using cold extraction analysis for total heavy metals. Numerous areas showing stratigraphical and structural similarities to Tynagh were then selected for reconnaissance geochemical prospecting.The Gortdrum deposit was detectable through the presence of anomalous metal values in stream sediments 3,000 feet downstream; soil sampling indicated an area of 2,000 by 700 feet containing 2 Yz to 20 times background cold-extractable metal values. Induced polarization surveys defined the dimensions and attitude of mineralization.Drilling to date has outlined (under 10 to 20 feet of till) low-grade copper-silver mineralization within Lower Carboniferous limestones and shales which have been faulted against Devonian sandstone. Mineralization ex-tends from surface to depths of 250 to 450 feet and consists of bornite-chalcocite-tetrahedrite and some chalcopy-rite in altered limestones and intrusive dikes.The deposit is geologically analogons to the Tynagh and Silvermines orebodies, but in contrast exhibits a predom-inant structural control. Provisionally, it is postulated that mid-Carboniferous folding and faulting produced the pre-mineralization high porosity via recrystallization, shearing and brecciation. Subsequently, hydrothermal solutions from the west, with a probable eommon origin to the volcanic dikes, were introduced along the fault planes. Although syngenetic causes cannot be exempted, the field relationships favour an epigenetic origin."

Jan 1, 1967

By G. W. H. Norman

INTEREST in the mineral possibilities (gold, copper) of northern Quebec, north of the Quebec-Cochrane branch of the Canadian National railway, has centred for many years in the Chibougamau district (see Figure 1). Since 1934, however, promising gold discoveries in the Rose Lake-Florence River section, 115 miles southwest of Chibougamau lake, have widened the interest, and prospectors have examined other parts of the country between Chibougamau lake and Bell river and the surrounding districts. The object of this paper is to !resent an outline of the geology, and to describe the mineral deposits, o part of this region, or, more specifically, of the part embraced by the Opawica-Chibougamau and Waswanipi map-areas(l), which include the districts about Chibougamau lake and Rose lake-Florence river, where mineral deposits are now in course of development either by surface or underground work. Early discoveries, developments, and explorations in the Chibougamau district are well summarized in the report of the Chibougamau Commission, published in 1911(2). The Commission discredited previous optimistic accounts of mineral discoveries in the area, made initially in 1903, but at the same time they expressed the opinion that, from a geological standpoint, the district promised a reward to diligent and intelligent prospecting. Their general conclusion-that prospecting in the area was not then (1911) commercially advisable in view of its inaccessibility and other handicaps shifted interest from the district until, some years later, valuable discoveries were made in the Rouyn area, and aircraft widened the field of successful exploration. During the past ten years or so, considerable energy has been spent in promoting the development of the district. The net result has been the discovery of a number of prospects, the majority of which have been explored only by trenching and, in most cases, diamond drilling.

Jan 1, 1936

By M. Somppi, D. Weirmeir, Z. Yamak

"Milling operations commonly employ activated carbon to capture complexed gold from lixiviants in leaching processes. As the carbon moves through pipes, pumps, vessels, kilns and other processes in the gold leaching circuit, this consumable may experience losses by various mechanisms like attrition, breakage, and rupturing. Whenever possible, capturing the fine gold-bearing carbon portion of this stream could provide value to milling operations at low capital cost and manageable financial risk. Identifying, testing, and validating the successful payback of a low-tech flocculant system is described. However, the work more closely explores a Monte Carlo risk-based methodology for understanding the potential payback of this project at various confidence levels – an approach that many improvement projects can follow where some level of uncertainty exists.INTRODUCTION Gold milling operations commonly employ activated carbon to adsorb gold from solutions. Normal handling causes the carbon particles from this material to abrade, break, rupture to a size that becomes too small for further use in the process. Operations often concentrate on capturing the fine particles because gold is associated with the carbon and this metal content can be a valuable revenue stream for toll processing. However, the small particle sizes become difficult to separate from the process and can ultimately leave the facility in the waste stream. Hence, operations often place a great deal of care in capturing as much fine carbon as possible by a variety of methods including using screens, settling tanks, and chemical methods. Retrofitting a circuit to capture more carbon fines is common but can expose the operation to financial risk. Approaching this potential improvement by leveraging a Monte Carlo methodology can be effective in understanding the risk and the associated payback of a project at various confidence levels. This method provides a strong framework for capital go-no-go decisions and the structure to validate the potential project success before implementation."

Jan 1, 2019

By V Dolmage

Copper Mountain is the third largest copper mine in British Columbia, and is now producing close to 20 million pounds of copper per year, with which is recovered also 4,000 ounces of gold and. 13,800 ounces of silver. After a long and checkered career, during which the ownership and management changed several times, this deposit finally came into the possession of the Granby Consolidated Mining, Smelting and Power Company in 1923. It was not, however, until the end of 1925 that the mine, under the management of Charles Bocking and C. H. Smith, was successfully placed on a basis of profitable production. It is a low-grade deposit of the contact-metamorphic type, with refractory ores consisting of chalcopyrite and bornite in a gangue of altered andesitic and basaltic breccia. The ore is concentrated to a product carrying over 30 percent copper, which is smelted in Tacoma. The deposit is 12 miles south of the town of Princeton, which is on the Kettle Valley railway, 150 miles east of Vancouver and 40 miles north of the International Boundary line. Princeton is served also by a branch of the Great Northern railway, which leads clown the Similkameen, Okanagan, and Columbia valleys. Copper Mountain mine and camp are connected to Princeton by a good mo tor road extending up Wolf Creek valley, while the haulage level of the mine, which emerges on the steep side of the Similkameen valley 1,000 feet below the camp, is connected with Princeton by a spur of the Kettle Valley railway leading up the Similkameen canyon and passing en route through Allenby, where the concentrator is situated.

Jan 1, 1929

By H. C. Gunnings, C. O. Swanson

"The Sullivan mine; at Kimberley in southeastern British Columbia; is the largest silver-lead-zinc mine in the Empire and one of the largest in the world.The original discovery was made in 1892 by four prospectors. Until 1899, when the branch line of the Canadian Pacific railway from Cranbrook to Kimberley was completed, little work was done on the property. In 1900, systematic development was started, and during the next 3 years 5,000 tons of ore was shipped to the smelters at Nelson and Trail. By 1903, some 300,000 tons of ore was developed, and a smelter was started at Marysville, about 5 miles from the mine. However, this smelter closed down in 1907 because of metallurgical difficulties after treating 75,000 tons, and the property came under the control of the American Smelting and Refining Company. An option on the property was taken in 1909 by the Consolidated Mining and Smelting Company of Canada, who exercised their option in the following year. During the next 5 years by selective mining and sorting 188,000 tons of high-grade ore was produced and shipped to Trail. This tonnage came from the upper levels, about 4,600 to 4,800 feet in elevation. At the same time, deep drilling down to the 3,900-foot level showed the presence of an immense body of complex ore. In 1915, the main adit-the 3,900-foot level-was started, and by 1919 this had been driven a distance of 2 miles to develop the ore above this level. Meanwhile, progress was being made in overcoming the milling problems. An interesting account of this work was written by the staff ( 4). In 1923, the first unit of the present concentrator was erected, with a capacity of 2,500 tons a day, and thereafter the rate of production increased rapidly. In 1934 it was around 8,000 tons a day, and to date a total of about 30,000,000 tons of ore has been sent to the mill. In recent years, a considerable part of the production has come from levels between the 3,900-and 3,350-foot, which were opened by an internal incline shaft started in, 1930. In 1942, tin was added to the products separated at the concentrator."

Jan 1, 1954

By David McMullen

Radiation plays a critical role in the thermal behaviour of hydrometallurgical process equipment. This effect is particularly important when designing refractory lined equipment used in pressure leach/oxidation processes. In order to simplify this non-linear mode of heat transfer, the effects of radiation had previously been incorporated in an equivalent convective film coefficient in finite element methods (FEM). This prior method omits the effects of radiosity, a critical aspect of radiation heat transfer, which affects the design of refractory lining systems in autoclave vessels. Given that 60% of the heat loss in actual plant practice of an autoclave is due to radiation, reliability in the FEM is therefore impacted. This study validates the use of radiosity in FEM through thermal loading using a combination of simple geometries to be applied to complex environments such as vessel nozzle clusters. The added benefits of using a radiosity load includes an increase in confidence in thermal distribution results, greater accuracy in determining appropriate refractory lining systems, weld overlay sizing, and increased accuracy in structural analysis.

Jan 1, 2014

By Robert B. Parsons

"The Whitehorse Mining Initiative (WMI) brought together all of the key stakeholders in Canada's mining industry to develop a framework whereby the industry can meet the challenges that it faces into the 21st century. The WMI Accord7 which was signed at the annual Mines Ministers Conference in Victoria, British Columbia, on September 137 1994, touches all of the important issues that confront the industry, including taxation. IntroductionSeptember 13, 1994, was a historical day for Canada's mining industry. On that day, on the occasion of the annual Mines Ministers Conference in Victoria, British Columbia, the Whitehorse Mining Initiative (WMI) Accord was signed by the leaders of the five principal stakeholders in the industry: industry; government; labour; environmentalists; and aboriginals. The Accord is the culmination of two years of hard work and intense collaboration by these stakeholders. But, the Accord is not the end result. The Accord can better be described as a springboard to a prosperous future for mining in Canada.The WMI had its beginnings at the Mines Ministers Conference in Whitehorse, Yukon, in September 1992 (hence, the name of the initiative). At that time, the mining industry was well aware of the serious challenges facing the industry, including significantly increased competition for mineral investment from other mining countries, coupled with an atmosphere of uncertainty surrounding land access, environmental regulations, and taxation. The diversion of investment abroad was hurting, and would continue to hurt, all Canadians. Something had to be done. At the 1992"

Jan 1, 1994

By H. Rozovsky

This paper deals with the large iron ore concentrating plant owned by the Iron Ore Company of Canada. The plant is part of the Carol Project, which is being developed in the Wabush area of western Labrador. The mining and milling operations were officially opened in July of this year. The handling of fine material has always been considered a serious operational problem. The crushing, grinding and sizing of 50,000 tons of iron ore per day, in a dry state, could present sizeable problems in maintenance and orderliness. The operation, as a whole, embraces many recent developments in the iron ore industry. Mining operations include the latest techniques of jet piercing and blasting. Primary crushing involves a single crusher, which handles the complete production. Grinding of the ore includes the latest concepts of dry autogenous grinding in air-swept mills. The actual concentration of the ore is per-formed, in the wet state, by the use of spiral concentrators, with provision for possible flotation or magnetic separation, if required. The upgraded concentrates are either stored or pelletized, prior to shipment by rail to Seven Islands.

Jan 1, 1962

By G. F. Vander Voort

Over the past twenty years, steelmakers have introduced improved practices for reducing the inclusion content of steels. The success of these practice changes can be monitored in a variety of ways. Chemical analysis of the bulk sulphur and oxygen contents provides a relatively simple means to assess the impact of these changes. However, microscopical test methods are still needed to assess the nature of the inclusions present. Traditional chartbased measurement methods have wide acceptability, and their data are well understood by both purchaser and producer for heat acceptance purposes. However, these methods do have inherent weaknesses which limit their usefulness for quality control, SPC, and database applications. Image analysis-based chart measurements are an improvement over manually generated chart ratings, but the data still do not lend themselves to databases and statistical comparisons. ASTM Committee E-4 on Metallography has developed a stereologicallybased image analysis standard test method, E 1245, which provides the necessary data in a form which is easily databased and analyzed statistically. This paper describes E 1245 and shows how data from different heats and melting practices can be compared statistically to ascertain valid test differences.

Jan 1, 1998