Search Documents

By C. Denis Thibodeau

Outline Introduction 402 OB Mining Sequence Trial to Verify Sequence Change Monitoring Observations Numerical Modelling Conclusion

May 1, 2013

By Michel Carreau

Presentation topic Introduction to Renewable Power in Remote Mining Industry Trend What are the Challenges and How to address them Acceptability (Management Buy-in) ? RP not core business to mining company Significant upfront costs Project Risks - Technological and Delivery Wind and solar power variability Operating hybrid power (Operator Buy-in) Conclusion Introduction ? RP at Remote Mining Sites Mining Project Cost Energy represents 25% of mining project CAPEX Energy represents 25% of OPEX Diesel, HFO, ? cost : 30+ cents/kWh RP - Proven technology - Excellent track record ?Wind (20 years), Solar PV (10+ years)? Hundreds of GW installed ?Reliable, High availability, very small OPEX. ?Wind/Solar cost : 15 to 22 cents/kWh (with good resource) ?Potential 10% to 20% Reduction in net cost of energy ?Price certainty for 20 to 25 years

May 1, 2013

By T. Patching

"Introduction The occurrence of coal was first reported in the Drumheller area in 1793 but it was not until 1912 that production of coal was recorded. In that year 13,000 tonnes were mined in the Drumheller area. Three years later the Drumheller mines ranked next in the Province to those in the Crowsnest and Lethbridge districts, with an output of 225,000 tonnes. By 1917 production had increased to 600,000 tonnes, moving Drumheller to second place in output in the province, second only to the Crowsnest district. It held this rank until 1960. Production, almost all from underground mining, rose to over a million tonnes a year by 1920 and remained between one and two million tonnes per year until 1954. Competition from newly discovered oil and natural gas, beginning around 1950 caused a steady loss of domestic coal markets, especially from underground mines. By 1960 Drumheller's production had fallen below a half a million tonnes per year and the field ranked third in output in the province, being surpassed by new stripping operations in the Castor field. By 1965 only a couple of producing mines remained in the Drumheller valley, and output was only about a quarter of a million tonnes per year(1). Throughout the life of the field production was seasonal, depending mainly on the domestic heating market. In 1979 the last mine ceased production. For the last several years of its operation it had remained open in the summers to provide tours for visitors(2). The Drumheller mining operations were located along or near the Red Deer River valley which is 300 to 400 feet deep, and extended from a few miles above the city of Drumheller to East Coulee, about 13 miles down the river in a south-easterly direction. Intervening mining communities existed for some years at Wayne and Rosedale. During the peak years of production some 2000 to 2500 miners and their families lived in these communities and the surrounding areas."

Jan 1, 1985

By E. A. Cleveland

A glance at the map discloses the fact that the Pacific Great Eastern railway either traverses or crosses some of the most important rivers of the province: the Squamish with its branches the Stawamus, Mamquam and Cheakamus; and the Green, Lillooet, Birkenhead, Fraser and Quesnel rivers. Each of these and some of their tributary streams, having their ?sources and upper reaches in the higher altitudes in regions of abundant snowfall, is capable in greater or less degree of furnishing water under suitable heads for the economic production of power. Beginning at its present terminus at Squamish the railway has the only hydro-electric development within its territory among the whole list of streams mentioned. A 225 horsepower installation at the edge of the East branch of the Squamish river, using water from Stawamus river, a branch of the former, under a head of 418 feet, is a modest beginning. Two or three additional sites, where water may be used under somewhat similar heads, may be found on this little stream. Next above Squamish, along the route of the railway, is the Mamquam, a long tributary of the Squamish from the eastern slopes. It has a drainage area of something like 130 square miles with widely varying discharges of from less than 50 to about 14,000 cubic feet per second. The preliminary investigations so far have disclosed no suitable storage sites, so the Mamquam may be regarded as a small continuous power stream - probably less than 1000 horsepower.

Jan 1, 1925

By Norman B. Davis

Introductory Feldspar is one of the most important mineral products consumed by the various branches of the ceramic industry. In the manufacture of table ware, electric porcelain, floor tile, and enamels, it supplies the chief fluxing ingredients necessary to bond the other more or less inert materials together when moulded into desired shape and fired in a kiln. Feldspar is used in the manufacture of bottle glass as a means of introducing alumina in a form easily assimilated. It is also used in certain scouring soaps particularly designed for cleaning enamel and glass surfaces. Feldspar, as it finds its way to the trade, is not a single mineral but is rather a mixture of various proportions of the feldspar silicate series, either in natural intergrowth or blended in the milling process, to produce a desired result. It is often further modified by the presence of quartz in amounts up to 30 per cent. The table on the next page gives typical commercial analyses of feldspar from various sources. Canadian feldspar produced to date has consisted mainly of the high-potash, relatively low-soda, variety, and has enjoyed a good market in the United States for the manufacture of enamels, electric porcelain, and vitrified table-ware. About eighty per cent of the output has been exported to the United States, but, with increased milling facilities in Canada and changes taking place in domestic United States sources of supply, the proportion exported will be reduced next year.

Jan 1, 1931

By B. H. Weber

"Industry generally has become noise-conscious and is realizing that damage to the human ear is expected to become more costly than any other compensation. Noise control has been recognized as a necessity and, fifteen years ago, in co-operation among different countries, inter-national organizations were set up to co-ordinate measures against dangerous noise and the development of silencing devices began. Rock drills for underground operations were particularly scrutinized because of the explosive nature of the noise developing from air escaping from exhaust. This paper describes the results and the present stage of development in the reduction and control of noise on rock drills, with special application to their use in mines."

Jan 1, 1970

By Roy O. Ifill, W. Charle Cooper, Alan H. Clark

"Queen’s UniversityIn representative, run-of-mine samples from the Panel and New Quirke mines of the Elliot Lake uranium district, Ontario, brannerite, ametamict uranous titanate, occurs in microscopic grain-aggregates which display wide variations, both in textural habit and in the relative proportions of brannerite, titania polymorphs and/or “uraniferous titania”. As is widely documented, much of the brannerite occurs as trellis-like arrays of laths and needles pseudomorphing rutile oranatase. In some cases, the laths and needles are cemented by coffinite. Brannerite, with an average composition of (U0.629Th0.039Ca0.20)(Ti2.199Fe0.13)O69contains =3 wt% Th and is distinctly Ti-rich relative to the ideal composition, UTi2O6. Much of the Si reporting consistently in electron microprobe analyses (between 1 wt%and 5 wt%) is tentatively attributed to contamination by the quartz-sericite matrix, and a minor proportion is attributed to the presence of coffinite intergrowths. “Uraniferous titania” (average par-tial composition by weight: 10.8% U, 0.3% Th,32.9% Ti) is considered to represent an intermediate stage in the conversion of titania to brannerite.The leaching behaviour of brannerite in its different modes of occurrence was studied qualitatively by the rotating-disc (polished section) method in H2SO4and HCl solutions at 25° to70°C. Redox potential was not measured. The progress of the dissolution of the individual brannerite crystallites and grain-aggregates was monitored by optical and scanning electron microscopes. Regardless of its morphology and texture (laths or needles, reticulate or blocky),brannerite is not readily leachable. Regardless of the process conditions, the rate-controlling step appears to be the initial leach-pit formation. These pits expand radially through the aggregate as leaching proceeds. This dissolution mode is independent of the relative amounts of brannerite and titania, i.e. the type of grain-aggregate. Secondary coffinite intergrowths are readily leachable and enhance the overall leaching kinetics of brannerite by accelerating leach-pit formation. These data provide, for the first time, information on the controls on the leaching of the uraniferous phases which dominate the lower-grade ores in the Elliot Lake district."

Jan 1, 1996

By J. D. Corbett

The spatial coincidence of the seven anomalies is obvious, even though the self-potential is offset northward. Because the ratio, as an indicator of conductivity, is a relative estimate at best, concise interpretation is limited in almost every instance to the location of a conductor or conductor axis. When related to the initial phase of an exploration program, magnitudes and ratios similar to those obtained from any one of the methods described, would be sufficiently attractive to warrant further investigation. The compilation shown is an empirical comparison of actual field results and no emphasis has intentionally been placed on the relative merits of one method in respect to another. Too many additional factors, i.e., size, depth and conductivity of overburden, etc., that cannot unequivocally be answered, enter into such a comparison before a relative evaluation can be made.

Jan 1, 1961

By W. A. Jones

"The Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is near the north end of lot 1, con. II, Hislop tp., Ontario. The property comprises the north half of lot 1, con. II, and the south onethird of lot 1, con. III. It is readily reached by a good motor road from the village of Ramore, 7 1/2 miles to the southeast on the Ontario Northland railway. The mine is being developed to a depth of 1,500 feet, and the current daily production rate is approximately 300 tons. From the inception of operations in March 1935 until December 31, 1945, 692,000 tons of ore, with a total value of $5,762,685, was milled . The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines.TYPE OF 0REBODIES AND MINERALIZATIONThe orebodies consist of lens-shaped and pipe-like stringer lodes and tabular vein zones composed of parallel quartz stringers. The host rocks are steeply inclined eruptive breccias and tuffs, striking N.70°W., intruded by very small stocks of red syenite. The orebodies appear to be spatially related to an intricate system of fault planes. Hydrothermal alteration is widespread and is not zonally related to individual quartz stringers. The wall-rocks contain abundant fine-grained pyrite, but gold is confined to the quartz stringers.RELATIONSHIP TO REGIONAL STRUCTURELack of outcrops has prevented the detailed mapping of the Keewatin complex in the vicinity of the Ross mine with the degree of success that has been achieved in the Porcupine area.A northwesterly trending belt of slates and greywackes, bounded by faults, forms the central part of a broad anticlinal arch about 3 1/2 miles north of the Ross shaft. Lava flows forming the south flank of the structure face south toward the mine. If the sediments are to be tentatively correlated with the large areas of Keewatin slates and greywackes of the Porcupine area, it must be assumed that they are younger than the lava flows and that they have been down-faulted."

Jan 1, 1954

By K. Meshinchi Asl

In this study the effects of T4 and T6 heat treatments on microstructural characteristics of AZ91 alloy containing Rare Earth elements have been investigated. Formation of intermetallic Al1 1RE3 needle shape particles which have a good thermal stability reduces both formation of ß(Mg17A112) and discontinues precipitation in AZ91 alloy which are dominated at the grain boundaries and are responsible for poor mechanical properties specially in elevated temperatures. For AZ91-RE samples both T4 and T6 heat treatments led to a continuous precipitation of ß particles at the grain boundaries after aging. However, in AZ91 samples (with no Rare Earths) precipitation was discontinuous at grain boundary areas. This type of precipitation is one of the main reasons of poor mechanical properties of this alloy at elevated temperatures.

Jan 1, 2007

By P. A. Riveros, R. Molnar, F. J. Baša

"An acidification circuit was installed and operated at the Agnico-Eagle Silver Division refinery in Cobalt, Ontario, for treating ~300 m3 of a concentrated cyanide waste solution with the purpose of recovering its cyanide and metal values. The acidification circuit was designed from parameters determined experimentally at CANMET. Available refinery equipment was assembled according to a flowsheet developed by Agnico-Eagle Mines. The process produced a regenerated cyanide solution containing >15 g/L of free cyanide, which was used for leaching gold ore at another Agnico- Eagle operation. It was estimated that the value of the recovered cyanide offset the treatment cost. BackgroundThe Silver Division of Agnico-Eagle Mines needed an economic and effective method for disposing of ~300 m3 of a concentrated cyanide waste solution that had remained in the plant after the operation was shut down in 1989. As a result of extensive recycling and evaporation, the solution had become practically saturated with metals, cyanide, thiocyanate, sulphate and other components, and was, therefore, an environmental liability for the company. A partial analysis of the solution is presented in Table 1. Initially, the use of cyanide destruction methods was considered by Agnico-Eagle, but the estimates indicated a considerable cost with no credits to be gained. A research project carried out by CANMET showed that a simple procedure consisting of acidification, filtration and reneutralization was the most attractive option, because it enabled the recovery of a substantial portion of the cyanide. Furthermore, the metals would be recovered in the form of a solid precipitate. The research showed that conventional AVR was not applicable because of excessive cyanide degradation and low HCN volatilization obtained with this particular solution (Riveros et al., 1996). This paper describes the procedure used to treat the concentrated cyanide waste solution and the operating practices of the large-scale acidification circuit run at the Agnico-Eagle refinery."

Jan 1, 1998

By F. E. Lathe

The method of feeding blast-furnaces to be described below is simply the application of well-known principles, and an attempt to carry that application to its logical conclusion. It does not involve radical changes in equipment, nor does it require unusual skill on the part of the furnaceman. In fact, much of its value lies in its very simplicity. Before giving details of the method it will be well to consider briefly the conditions under which it was used at the Nickelton plant of the British America Nickel Corporation, in the Sudbury district, before that plant closed down. The Sudbury nickel ore consists chiefly of pentlandite, chalcopyrite and pyrrhotite in a gangue of norite or greenstone. The proportions of sulphide and gangue vary widely in different mines, the former constituting about 45 per cent of the total in the British America sorted ore. The gangue is fairly uniform in analysis, carrying about 55 per cent Si02, 18 per cent A120 3, 13 per cent FeO and smaller quantities of CaO, MgO, Na20 and K20. The ore has been frequently described as refractory, a word which seems suitable when one considers the many unsuccessful attempts to smelt it pyritically, as well as the high percentage of coke normally used at all the plants in the district.

Jan 1, 1925

By Brian G. Pewsey

Located in the northern part of the Province of British Columbia, the Cassiar Mine started development of its asbestos orebody in 1952, and is currently producing 105.000 tons of asbestos fibre annually. The townsite is nestled in a beautiful valley and supplies more than average facilities. The fibre is shipped to more than 40 countries and is used in many industrial products.

Jan 1, 1978

By A. Torkian

Process water from production of concentrates in Meydook copper sulfide mine is transferred to the 8.3 million m3 tailings dam and a water retention pond after initial thickening. Elevated concentrations of heavy metals, sulfate, and TDS and decrease in pH as well as seepage into the aquifers have been the concern of the regulatory agencies since the start of activities. In this paper the results of a 6-month monitoring program from 4 wells are presented. The wells were located approximately 1.5 km from downstream of tailing dam (0.4 km from water retention pond) as well as upstream background well (2.28 km from water retention pond and 1.27 km from tailings dam). The objective was to study possible effect of accumulated tailings on the groundwater resources. Water levels in sampled wells were on average between 20 and 40 m. Results showed high levels of lead (5 ppb), copper (0.17-0.46 ppm) and selenium (73.1- 29.1 ppb). High levels of selenium and lead were partly due to natural geological settings of the area with high levels present in unaffected soils in the vicinity including water wells of villages upstream of mining operations. High copper levels were attributed to both mining operations as well as deposition from particulate air deposition onto the soil and transport to ground water by rain.

Aug 1, 2013

By ManhKha Trinh, Neal Pyke

Dofasco was the first company to adopt oxygen steelmaking in North America in 1954, two years after the first LD vessel installed and operated successfully in Linz, Austria. Since then, Dofasco has investigated and implemented several strategies to maximize hot metal usage and minimize overall cost. Some key strategies -low hot metal silicon, combined blowing conversion, vacuum degassing tank upgrade and BOF slag carryover control - are discussed. Post combustion, scrap preheat, carbon injection trials along with current operating philosophies are described.

Jan 1, 2004

By Roger K. M. Bellows

The last coal-fired power plant to be built in Canada came into operation in 1994. Since then, Canada?s electricity requirements have grown substantially but no new coal-burning plants have been built. This country has abundant resources of coal from coast to coast, but in recent years, this has not affected our choice of fuel. In many other countries this is not the case, and the use of coal is growing rapidly. Although this presentation covers the topic from an Alberta perspective, some of the conclusions can be extrapolated to the rest of the country, and perhaps even to other countries. The coal found in the Alberta plains is particularly attractive because of its low cost and low sulphur content. Yet coal is no longer the fuel of choice, and a long-standing provincial government policy to favour coal for electricity generation has been ignored for more than a decade. Considering the lack of good alternatives, it seems obvious that we should look to coal as our primary energy source in the generation of electricity and for other industrial applications. This paper discusses some of the reasons that coal has fallen out of favour, particularly with respect to electricity generation. The significance of the deregulation of the electricity industry will not be ignored. In addition, the author will offer his opinion on the question of what it will take in order for coal to once again become the favoured fuel.

May 1, 2001

By G. G. Bowser

THE time has come when, as your President, 1 turn the helm over to my worthy successor. When 1 was reminded by our Secretary that 1 had to prepare an address for this meeting, 1 was at a loss for a subject. In the hope of inspiration 1 perused the records of our Society for some years past. 1 found in these records that many problems in need of solution relative to industry in Nova Scotia were discursively dealt with and that sound thought was given to the solution of these problems, with a natural leaning, of course, to problems pertaining to the mining industry. 1 found also that some of the reasoning was remarkably prophetie. Some of these subjects and problems were: The use of pulverized coal to generate power instead of hydro-electric power; rural electrification; the importance of youth training for an efficient place in industry; the proper marketing of coal; the fuels competing with coal; the need for better in-dustrial relations between employer and employee; better education for success in the social field as applied to industry; and Canadian unity. The issue of some of these copies has been forced upon us by war. For instance, there appears to be no marketing problem for coal, nor does there ? seem to be a marketing problem for anything just at present. The problem of the coal producer just now is supply and transportation. Also, at present, coal fe.ars no competitors, such as oil-and not even hardwood. Many large companies now have an industrial Relations or Personnel Manager and department. Furthermore, we have been compelled of necessity to train our young men, and women also, for both industry and war. However, war does not solve these problems and, with the return to normal times, we may be faced with the same troubles in even greater measure. My reason for mentioning these copies is to point out that, as mining men, we are aU desirous of progress in every industry, not only the mining industry; and that mining men are able to see clearly ahead. In normal times, especially in matters not directly affecting the mining industry, we are inclined to let matters take their own good rime, or let the government do it. We do not seem to realize that these necessary and desirable changes can be made in times of peace-instead of being forced upon us by war or other social upheavals-by the method of sound thought and action to the desired end.

Jan 1, 1943

By Y. Wang

In this study, homogeneous (unseeded) precipitation of nesquehonite (MgCO3.3H20) by the reaction of MgC12 with (NH4)2CO3 in supersaturated solutions at 30 °C was investigated. Factors which influence the precipitation of MgCO3.3H20, such as initial concentration, temperature, stirring speed, titration speed, equilibration time, have been studied. SEM images show that the initial concentration and titration speed have significant effect on nesquehonite's crystal morphology and particle size. In addition, stirring speed and equilibration time also have some influence on its properties. With the optimization of operating conditions, the crystals can grow up to a length of about 40µm and a width of 5µm, indicating good filtration properties. High purity nesquehonite obtained in this study was calcined to produce highly pure MgO at 800 °C as shown by XRD results. The novel process may be used to separate Mg and Li from high Mg/Li ratio brines in Qinghai, China.

Jan 1, 2007

By D. L. Griffith

THE realization by metallurgists of the important effect that traces of impurity may have upon the properties of a metal, and their steady demand for purer and still purer metals, have made the special cools for 'trace' analysis of increasing value. In the United States at least, spectrographic analysis is becoming the standard method for determining the impurities in zinc die-casting alloys. The Hudson Bay Mining and Smelting Company, as a producer of virtually pure zinc, uses the spectrograph to control the purity of its products, and-as the electrolytic method is employed here-to control both the impurities in the electrolyte and those 'trace' elements, which, while they do not contaminate the zinc, have a great effect on the plating efficiency. The general plan of the laboratory is shown in Figure l; the housing for air purification, which is on the roof, is indicated by broken lines. One of the chief factors affecting the layout was the easy way in which a spectrographic assay can be spoiled by contamination. To minimize the quantity of dust tracked in, the laboratory was made separate from the general research laboratories, and an office was placed between the two. This arrangement has its drawback because of the traffic through the office, but it has effectively cut down dust. For similar reasons, the available space was subdivided into a number of small rooms, and the air currents in the laboratory were so arranged that dust would be carried where it would do least harm. Air is drawn in at the roof over a 50-kilowatt bank of Calrod heaters, through Annis air filters, by a No. 4 Sirocco fan. Most of it is forced into the spectrograph room, but some goes to the office and darkroom. The air flow is from the spectrograph room, through the plate-measuring room, into the chemical laboratory, where it is exhausted by a No. 1% Sirocco fan on the fume hood. Air can also re-circulate from the plate-measuring room back to the heater. The arrangement is such that the air in the laboratory is maintained at higher pressure than the outside air; consequently, no dirt enters through cracks about the windows and doors. A thermo-regulator holds the temperature constant within one or two degrees; only on the hottest days in summer does the temperature rise enough to affect the focus of the instrument.

Jan 1, 1940

By Muhammad Zaka Emad

Cemented rockfill (CRF) is a mixture of rock aggregate and binder slurry. It is a stiff backfill, it is fast curing, its operation is simple, placement rate is reasonably high and no drainage is required. The main demerit of CRF is failure of exposed faces causing ore dilution, which can be associated with the fill placement method. This paper discusses the effects of two placement methods being practiced by mines and numerical modelling is used as a tool to evaluate stability of the backfill column. In the first method, practiced in longitudinal retreat mining of a narrow vein deposit, the rockfill is hauled and dumped into the stope with a LHD scooptram. Once dumped, cement slurry is sprayed into the stope. In the second method, a raise situated centrally above the mined stope is used to convey already mixed CRF into the stope. Stopes are mined out transversely in primary and secondary blocks in a sublevel stoping system. Problems of poor mixing in combination with both placement methods are discussed. The two backfill placement methods are analyzed for blast induced vibration damage using the dynamic Flac3D modelling technique accounting for rock mass and fill damping characteristics, and a pressure wave is used to simulate the blast vibrations. Fill heterogeneity has also been considered for the two cases and results are compared.

Jun 1, 2012