Search Documents

By F. W. Gray

A GEOLOGICAL study seeking to determine, for economic purposes, the value of the Sydney coalfield as a source of coal supply. Limitations of the coalfield come under two main heads: (a) Areal extent of the undersea coalfield. (b) The distance from shore at which coal can be mined at a cost of production permitting its profitable sale. Conclusions reached are that the areal extent of seams below the Phalen seam is of. small economic importance, and that non-persistence of these seams in full thickness and quality in the undersea extension of the coalfield will put an end to profitable mining before any limitations connected with distance from the shore-line become operative. With respect to the Phalen seam, non-persistence or deterioration of the seam will become effective in the western part of the coalfield, and less certainly in the eastern part of the coalfield, before operation of limitations by distance from shore. In the central portion of the coalfield, the seam probably persists in commercially workable thickness and quality to beyond the limit of mining set by distance from the shore-line. With respect to the seams above the Phalen seam between the Mountain fault on the extreme western boundary of the coalfield and the assumed termination of the deposition area on the eastern extremity of the field near South Head of Morien, there appear to be only such limitations as arise from engineering approach, distance from shore, sufficiency of strata cover between the sea-floor and the upper coal seams, and quality of the coal (with certain reservations as to the continuity of the upper seams under Sydney harbour and in the Sydney Mines-Little Bras d'Or district). Some of these seams have fragmentary land outcroppings from which their persistence seaward is assumed, and there may be other and still higher seams in the strata column which are entirely submarine.

Jan 1, 1941

By M. P. Tixier

Abstract In a review of the application of electrical logging in Canada, examples are .given of long and short distance correlations by means of the electrical logs. The use of MicroLogging for the determination of permeable and porous formations is explained. The question of log analysis for the quantitative determination of fluid saturation and porosity is .discussed. An example is provided to illustrate the significance of the resistivity gradient. The advantages of the new method of the Laterolog are shown, chiefly for the case of wells filled with high-salinity mud. Introduction Electrical logging techniques developed rapidly in Canada at the time an intensive drilling activity started for the exploitation of the Devonian series in Alberta, namely, at the beginning of 1947. The conventional service was soon thereafter supplemented with the latest technica1 improvements. Canada has been among the first regions to take advantage of MicroLogging*, which has proved a most powerful .tool for the investigation of permeable and porous formations; also, the more recent development known as the Laterolog has ?been introduced in Canada. The Laterolog provides a better determination of .the formations, particularly in the case of salty mud where the conventional logging is greatly handicapped. The various methods of electrical logging are now commonly known in oil industry and have been described in numerous publications ( 1) ( 2) (3).

Jan 1, 1951

By L. M. Pidgeon

Introduction The production of magnesium by direct reduction of the oxide has far passed the experimental stage and was responsible for 30 per cent of the recent wartime production of 246,000 tons per annum. This paper describes the small-scale experiments which culminated in a number of the wartime plants. The paper traces the author's early experiments on various direct reduction reactions leading to his choice of the ferrosilicon reduction of dolomite and the realization that this reaction would proceed at a satisfactory rate at temperatures obtainable in metal apparatus. MgO has a standard heat of formation of 146,100 cal. and is therefore one of the most difficult oxides to reduce. However, if advantage is taken of the relative volatility of magnesium metal, thermally unfavourable reactions may be utilized. In reaction MgO + X = XO+ Mg . . . . . . . . . . . . . (1) the removal of Mg as a gas at high temperatures displaces the equilibrium to the right in the face of the unfavourable thermo-chemistry which is inevitable with any X other than calcium metal. If X is carbon, not only is the reaction highly endothermic, but CO is gaseous. A temperature of l,864°C. is required to produce a pressure of one atmosphere of Mg. Between l,900°C. and perhaps 400°C., the back reaction takes place readily and special shock cooling devices are required to recover magnesium from the gaseous mixture. This reaction does not lend itself to small-scale experiments and was not examined by the author. If, in reaction, carbon is replaced by a relatively pan-volatile metal, the oxide of which is also non-volatile and possesses a fairly high heat of formation, a reduction reaction is offered which is free from the difficulties associated with carbon. The typical case of silicon will serve as an example: 2MgO + Si = SiO2 + 2Mg (g) . . . . . . . . . . . . . . . . . . . . . . (2) At temperatures above l,000°C., a positive pressure of magnesium will exist over the system. Removal of the magnesium vapour will displace the reaction to the right in the face .of an unfavourable thermal balance. Since magnesium is the only volatile component at this temperature, it may be evolved and condensed, using attractively simple distillation technique.

Jan 1, 1946

The integration of mining and mineral processing technologies into new advanced mining systems is considered to offer several benefits, including selective mining, reduction in waste, increased productivity, flexibility, and improved resource utilization. This paper focuses on underground hardrock mining and the integration of pre-concentration technologies into future mining systems as representing realistic, shorter-term integration options. Control of fragmentation to optimize grinding, pre-concentration of ores, in situ leaching, and modular mining/mineral processing systems are possible with existing technology. Current research is directed toward development of integrated underground systems that minimize surface activity and minimize or eliminate surface waste disposal. Results from a simulation model of an integrated underground pre-concentration system are presented.

Jan 1, 2002

By P. Karimi, G. Mollataheri, A. Amini, H. Abdollahi, A. Mirzaeian

"Chah-Palang tungsten deposit is one of the two tungsten indexes in Iran. Based on ore characterization techniques (including optical mineralogy and XRD analysis), quartz, chlorite, atacamite, azurite, malachite, ferberite, illite, goethite and calcite were distinguished as major minerals. The representative sample was analyzed qualitatively by using X-ray fluorescence and chemical assay. Results showed that grade of tungsten oxide and copper were 1.76 and 7%, respectively. Also precious metals such as gold with grade of 1 ppm was reported in the sample. By using the mineralogical studies on the prepared sample, the liberation degree of tungsten minerals in –0.6 mm size fraction was obtained 80%. Several tabling tests were carried out on the original sample which at the optimum conditions and as a result, the grade and recovery of tungsten in concentrate reached to proximately 23 and 59%, respectively. To increase the grade of tungsten in the final concentrate, acidic leaching were performed on the tabling concentrate and its appropriate results indicated that the grade of tungsten increased to 27%. Also more than 90% of copper was extracted as a byproduct in the fallowed process.INTRODUCTIONTungsten, a unique hard, heavy heat-resistant metal, is distributed erratically in economic concentrations throughout most continents, occurring mostly as small irregular deposits that are not readily adaptable to large-scale, low-cost mining methods. The diverse physical characteristics and mineral composition of tungsten ores also present problems in beneficiation, requiring complex hydro- and pyrometallurgical treatment to yield high-purity concentrates suitable for the production of ferro alloys, carbides and super alloys in the steel industry (Hausen, 1989; Kholmogorov & Kononova, 2005). Tungsten is most frequently used as tungsten monocarbide, which has hardness close to diamond, in cemented carbides. The most well-known use of tungsten is in lighting filaments, and other important applications include improving steel properties and use in tungsten alloys, electronics, and chemical products (Hausen, 1989; Kholmogorov & Kononova, 2005)."

Jan 1, 2016

By Jiuhua Xu, Yuling Xie, Fenglei Bie, Neng Jiang

"Abstract - The Xiaoqingling Mt. area is one of the most productive gold districts in China. The gold-bearing quartz veins are controlled by a series of east-west shear zones within the Archean Taihua Group, and related to the late Yanshanian (Cretaceous) granite. The major metallic minerals are native gold, electrum, pyrite, galena, chalcopyrite and sphalerite, with gangue minerals dominated by quartz, sericite, ankerite, and calcite. The host rocks are mainly amphibolite, plagioclase gneiss, and migmatites. Principal alteration is sericitization, silicification, pyritization, and carbonization.There are four generations of hydrothermal quartz in altered rocks of gold deposits. The earliest generation of quartz, (Q1), occurs in altered amphibolite gneiss and migmatite, and typically contains fluid inclusions with halite crystals (type A) and two phases, (L+V), of fluid inclusions (type B). The salinities of type A inclusions are 32 wt% to 52 wt%, with dissolution temperatures of halite crystals being from 155°C to 465°C. The second generation of quartz, (Q2), occurs as a fine-grained aggregate associated with sericite, and has small (less than 3 µm) type B inclusions. The third generation of quartz, (Q3), occurs in mylonitic, intensively altered rocks and specially beresite (a type of rock composed of quartz, sericite, and pyrite) near the veins, and contains large amounts of CO2-rich fluid inclusions (type C-fluid inclusions with liquid CO2 and type D-fluid inclusion with high density CO2). The CO2 contents of type C range from 72.6 to 87.4 mol% in gas phases, and 35.7 to 68.3 mol% in liquid phases, based on Laser Raman analysis. The homogenization temperatures of fluid inclusion type A and C are from 215°C to 380°C, and from 210°C to 325°C, respectively. The minimum trapping pressure of fluid inclusions is estimated as 80 MPa to 170 MPa for type A, and from 57 MPa to 190 MPa for type C, which approximate to those of fluid inclusions in vein quartz.The ?18O of quartz are from 10.4‰ to 11.0‰ for Q3 of altered rocks, and from 10.7‰ to 12.8‰ for stage I quartz. The calculated ?18O of fluid inclusions varies from -1.3‰ to 6.0‰. The ?D of fluid inclusions ranges from -67‰ to -59‰ and from -81‰ to -48 ‰, respectively. It is concluded that the water in the hydrothermal fluids both reacting with wallrocks and precipitating orebodies could have been mainly of magmatic and/or metamorphic nature. However, local meteoric water might have been important in late mineralization, because of a distinct oxygen-shift toward the meteoric water. The ?34S values for pyrite of the ores range from -7.1‰ to +7.1‰, with an average of +2.9‰. Those of other sulfides (chalcopyrite, galena, and sphalerite, range from -12.5‰ to 8.3‰. The ratios of lead isotopes for galena of the ores are: 17.06 to 17.31 (206Pb/204Pb), 15.43 to 15.74 (207Pb/204Pb) and 37.58 to 38.45 (208Pb/204Pb). In summary, ore-forming fluids in the Wenyu-Dongchuang gold deposits may have originated from a mantle and/or lower crust source, and ore materials were derived from the Precambrian basement, the Taihua Group."

Jan 1, 1998

By Charles G. Kemsley

MR. C. R. WHITTEMORE: It is interesting to note that the mining industry is making increased use of alloy steels for drilling. They will undoubtedly lead to greater footage at lesser cost. Mr. Kemsley states that, for use in hard ground, the shanks are brought to a hardness of 435 to 440 Brinell by heating them to approximately l,800°F. It seems to me that this temperature is excessively high-it is considerably above the critical point of the steel. The only effect of such a high temperature is to lessen considerably the impact resistance of the steel. The possibilities of an oil quench, followed by a tempering draw which does not lessen the hardness of the steel too much but increases its toughness, might well repay further study; also the temperature control, a factor which depends on the composition of the steel. However, service results are undoubtedly the best criterion of practice. MR. KEMSLEY: I would like to point out that the steel is not quenched at 1,800°F. After heating to this temperature, it is laid aside to cool gradually; this high temperature is necessary to produce the required hardness by simple normalizing-cooling in still air. We all know that ideal conditions for hardening steel demand salt baths and furnaces with automatic temperature control, but for most companies the cost of such equipment having sufficient output capacity is prohibitive. The end we are trying to attain is to make good drills at a cost that will be within the means of any mine.

Jan 1, 1942

By J. T. Kalala

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By J. A. Herbst

Professor Klaus Schönert and his students used fundamental physics to develop many of the principles required for the design and scale-up of "Gutt Bett Zerkleinern" devices such as the high pressure grinding roll (HPGR) or the high pressure roll crusher (HPRC). As the equipment evolved so have the tools used for its selection and analysis. In the current paper discrete element modeling (DEM), Metso's proprietary Fast Breakage simulations, and Schönert's packed bed piston test are combined with energy based population balance models (PBM) to yield an alternative to ore characterization and equipment selection by pilot plant testing. The resulting methodology is used to take the next step in understanding these devices with a view toward predicting plant performance. This paper describes a journey beginning with precise modeling of a small HPGR including stud geometry and system hydraulics. A key to predicting performance is the accurate modeling of individual particles, their motion in the machine, the probability of breakage and redistribution of fragments, and the inter-particle breakage events that occur between the rolls at different pressures, speeds and moisture levels. Advanced DEM simulations and particle breakage characterization methods provide the necessary technology. The resulting combined models were validated using a small diameter laboratory scale unit. The validated physics based model was used then used to predict the performance of plant scale units using a specific energy based scale-up method. Scale-up results are analyzed in terms of power draw, throughput, and discharge product size distribution.

Jan 1, 2012

By CH. Liu, H. X. Jiang, X. Xiao

"A study has been conducted to characterize the fatigue life in 7050-T7451 thick plate by the comparison between an experimental alloy and commercial alloy. The fracture origins were specified and their sizes were measured by scanning electron microscope (SEM). Additionally, the size, number density and spatial distribution of porosity in the experimental material and commercial material were characterized and compared, using X-ray Computed Tomography(XCT). The results showed that microporosity was the predominant site for crack nucleation and subsequent failure of the experimental alloy. However, as for the commercial alloy, fatigue cracks were found to originate from constituent particles. The presence of microporosity in 7050-T7451 thick plate reduced fatigue life of an order of magnitude or more compared to the commercial alloy. The relationships between size of origin and fatigue life were proposed. It was showed that the fatigue endurance was reduced when the size of porosity increased.INTRODUCTION 7xxx series aluminum alloys, due to their combination of high strength, high resistance to stress corrosion cracking, and good fracture toughness, are widely used in structural engineering applications where high-strength and low-density characteristics are fundamental design requirements (Williams& Starke, 2003). Every designer is striving to find an optimal combination of properties including strength, corrosion resistance and fatigue resistance (Wanget al., 2016). Based on the design principles of aircraft, a higher fatigue resistance of aluminum alloys are required. Thus, many investigations have been carried out on the microstructures and its effect on fatigue properties of the 7xxx series aluminum alloy (Robson, 2004; Schubbe, 2009).Microporosity, which is a common defect in casting materials, can lead to a significant deterioration of mechanical performance and fatigue resistance, especially in the high alloyed 7xxx aluminum alloys. The actual valid loading area decreases due to microporosity, which results in detrimental effect on the mechanical properties. Many experimental studies have been conducted in this research field. Mayer et al.(2003) investigated the fatigue properties of magnesium alloys produced by high-pressure die-casting. The results show that porosity in magnesium alloys greater than0.18mm diameter may be considered as the most important material defect for high cycle fatigue and fully reversed loading conditions. Nadot et al.(2004) found that the near surface defects are much more dangerous than the internal defects. Wang et al.(2001a) used the Weibull statistics method to analysis the influence of the microporosity, oxides and particles on the A356-T6 alloy fatigue life. The results show that, the porosity is more detrimental to fatigue life than oxide films and particles. With regard to fatigue resistance, although the deleterious effect of microporosity has been generally acknowledged, a quantitative understanding between casting microporosity and fatigue life in 7050-T7451 plate is not well established."

Jan 1, 2018

By G. V. Theja, V. B. Maji

Large infrastructure projects like tunnel excavations, underground constructions face innumerable risks. For successful completion of these projects, it is essential that we foresee and understand risks that could occur during different phases of the project. One of the risks affecting underground excavation projects is the inaccurate performance prediction of TBMs. As this could severely affect the project, resulting in lower advance rates and could also result in changing the excavation machine or method, due to difficulties in excavation, thereby increasing the overall cost of tunnelling. This makes performance prediction of the TBMs as one of the crucial aspects in tunnelling, as a precise estimation of its performance is required for planning and estimation of time and cost of the tunnelling projects. This performance prediction of TBM is a challenging geotechnical problem that is intricate and complex in nature, this is possibly due to the fact that TBM performance prediction involves understanding the rock fragmentation process in wide range from micro-scale (i.e. the interaction of surface of rock material and cutter tip) to macro-scale (including the interaction of rock mass and TBM). Thus in order for the performance prediction model to be efficient, parameters of both TBM specifications and ground conditions have to be considered. Various models have been proposed by researchers since the early phases of TBM application, these studies resulted in the development and improvement of numerous penetration prediction models. Most of these models consider the geotechnical parameters that are input to the model to be consistent along the TBM drive and neglect the uncertainties in parameters that occur. And so to improve the predictive capability of these models and to incorporate the above uncertainties, the penetration rate is modeled as a stochastic variable depending on the geotechnical and TBM parameters, its statistical distribution is determined and is used to characterize the penetration rate instead.

Jan 1, 2015

By Jean-Christophe Ehrström, Fanny Mas

"A specific test set-up has been developed to study at the lab-scale the high-temperature behavior of aluminium alloys in conditions close to those experienced by thick plates during hot-rolling. A particular attention is paid to reproducing both the stress triaxiality and strain fields that exist in plate during rolling. In addition to standard ductility measurements by means of secondary tensile tests (STT), multi-step plane strain compression (PSC) tests have been performed to mimic hot-rolling pass schedules. Tool and sample geometries were adapted to allow low h/a ratios (h= average specimen thickness, a= tool width) and thus guarantee depressive stress conditions at the center of the specimen during most of the test. Such conditions resulting in porosity opening can then be used to investigate the impact of rolling conditions on damage evolution. The mechanical testing was combined with post-mortem high-resolution ultrasonic scans allowing to detect small amounts of damage and quantify its evolution as a function of processing parameters such as strain and temperature. The test set-up was validated on two 2050-type AlCuLi alloys with different susceptibilities to high temperature embrittlement.INTRODUCTION Aluminium thick plates are widely used in the aerospace industry, mainly as semi-products to be machined for internal structure parts of wings (spars, ribs) and fuselage (frame). The conversion route of such products always involves a hot-rolling step, the conditions of which (temperature, speed, pass schedule) have to be optimized to maximize both mechanical properties and final plate quality. This goal cannot always be efficiently achieved by full-scale industrial trials as (a) cost limits the number of possible test conditions and (b) it is often difficult to change one parameter alone. That is why there is a need for laboratory-scale tests able to mimic the rolling process in terms of temperature, strain rate, stress triaxiality and deformation. Most laboratory hot-rolling mills do not adequately simulate industrial processing routes, especially in terms of heat loss, deformation speed and rolling geometry (maximum roll gap vs. work roll diameter). Concerning thick plate, it is of interest to achieve both similar deformation and L/h ratio (L=arc of contact, h=mean gauge) per pass as the industrial schedule because they are simultaneously involved in damage evolution and void closure during hot forming processes (Saby, 2014)."

Jan 1, 2018

Training by Inclusiveness ?Background ?Video ?Results ?Partners ?How SEM works ?Future of SEM Background: Inclusivity partners ?Northwest Community College ?Smithers Exploration Group ?With support from the Province of BC ?Federal government ?And First Nations across the northwest

May 1, 2010

By L. López

Argentina reported about 40,000 tonnes of uranium (tU) as reasonably assured resources and inferred resources for the production cost category <130 US$/kgU in the OECD-NEA/IAEA classification scheme. These resources belong to the following projects: Sierra Pintada, Cerro Solo, Don Otto, Laguna Colorada, Laguna Salada, Meseta Central and Amarillo Grande. With three heavy water reactors in operation and an approximate installed capacity of 1.7 GWe, the current natural uranium requirements are about 220–250 tU per year. Based on various nuclear growth scenarios, it is estimated that by 2030 there will be a generation capacity of some 3,092 GWe for the reference case, with raw material needs of some 486 tU per year. Currently, there are no perspectives for local uranium production in the short term, and it is thought that uranium projects with identified resources must complete resource delineation and advance in technical pre-feasibility studies for the recovery of uranium. It is expected that Argentina continue meeting the uranium demand with imports in the next following years. In the Latin America region, both Brazil and Paraguay could be considered as potential uranium suppliers. In conclusion, despite the apparent growth prospects for the use of nuclear energy to generate electricity in Argentina, there are no immediate prospects for the provision of uranium oxide concentrates from domestic deposits for fuel fabrication. This has implications for supply and energy security.

Jan 1, 2020

By T. Hidayat, D. Shishin, V. Prostakova, M. Shevchenko

The chemical compositions of copper feed streams are becoming increasingly complex following the growing demand for metals and corresponding shortages of primary sources. The optimisation of process conditions requires an accurate description of phase equilibria and thermodynamics. Integrated experimental and thermodynamic modelling research program on the characterisation of the complex, multi-component, multi-phase gas-slag-matte-speiss-metal-solids Cu2O-PbO-ZnO-Al2O3- CaO-MgO-FeO-Fe2O3-SiO2-S-(As-Bi-Ni-Sb-Sn-Ag-Au) system is being carried out to support companies undertaking the pyrometallurgical primary production and recycling of copper. The experiments involve high temperature equilibration in controlled gas atmospheres, rapid quenching and direct measurement of equilibrium phase compositions with quantitative microanalytical techniques, including electron probe X- ray microanalysis and Laser Ablation ICP-MS. The thermodynamic modelling is undertaken using FactSage computer package with advanced thermodynamic solution models. The continuing development of research methodologies has resulted in significant advances in research outcomes. Implementation of the results of these fundamental studies involves an ongoing collaboration of researchers and industry technologists. An overview of recent progress in research, implementation and applications in industrial practice are given in the paper. INTRODUCTION Rapidly developing technologies increase the demand for various metals in number and volumes. Modern technological devices such as mobile phones, computers, other electronic devices, have dozens of metals—all those metals have to be a) produced and b) recycled. The fast transition in mobility from fossil energy delivered through combustion to renewable energy first stored in bakeries and delivered through electric engines introduce a significant change in the metal demand in terms of both type and volume of metals. Pyrometallurgy is playing a key role in supporting these changes in our industrialised society.

Jan 1, 2019

By S. Flewelling, M. Scobie, G. R. Baiden

"SynopsisA feasibility study to develop a research program, the Mine Automation Plan (MAP), was recently completed. This was undertaken by a team comprised of Inco Ltd., Falconbridge Limited, the Canadian Centre for Automation and Robotics in Mining (CCARM) and the Centre for Resource Studies (CRS). The study was sponsored by PRECARN Associates, which is a consortium of thirty-six Canadian companies focussed on research and development in artificial intelligence and robotics. PRECARN Associates was formed in 1987 when a number of research proposals were funded in the fields of process control systems, robotics systems and intelligent engineering systems. In July 1991, PRECARN accepted the next round of proposals for research. The MAP project was one of the successful proposals, being awarded $100,000 for the development of a feasibility study defining a long-term R&D plan for underground hardrock mining automation.The development of the feasibility study started by addressing the fundamental structure of the mining process, and its relationship to the metallurgical process, over-all infrastructure support and management systems (Fig. I).Mining may be considered as comprising five subprocesses: (I) delineation; (2) development; (3) production; (4) backfilling; and (5) infrastructure support services. Within these subprocesses many applications for artificial intelligence and robotics exist. The mining process is dependent upon the interaction between the physical mining process and information. For example, the delineation process is dependent on geomechanical, geochemical and geophysical techniques to develop a model of the orebody based upon access to such data. This same relationship between the physical and information models holds true through the development, production, backfill and infrastructure support systems.The foundation for the MAP study has been the recent development by Inco Ltd. of an underground communications system (Fig. 2). The system has the ability to supply high bandwidth communications, over voice, data and video to mobile and stationary locations within the mining operation. It is seen to be the future backbone of a comprehensive, automated information system which should permit the application of the concept of Computer Integrated Manufacturing (CIM) to underground mining. CIM, through the automated flow of information, has been successful in integrating the engineering, production and various support groups in manufacturing."

Jan 1, 1994

By D. N. Madge

The use and development of industrial process control computers in the mineral industry during the 1970&apos;s has been sluggish. This cautious approach is due to lack of commitment by senior management. The lack of commitment is due to several reasons: variable mineral processes and technologies, market fluctuations, and excessive costs and inadequacies of applicable products supplied by computer vendors.

Jan 1, 1979

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By Francoi Robert, Andre J. Audet, Alex C. Brown

"The Sigma gold deposit is in a band of deformed metavolcanic rocks that are cut by an irregular mass of porphyritic diorite and by narrow undeformed feldspar porphyry dykes. The gold is in veins consisting mainly of quartz and tourmaline with minor pyrite, carbonate, chlorite, scheelite and free gold. The results presented here concern the structural setting of the ore and are based on a study of the mode of emplacement.Two principal types of veins have been recognized: subvertical and oblique veins. Both types are contemporaneous, mechanically linked and postdate regional deformation. The sub-vertical veins are composed of numerous mineralized lenses that occupy the central part of ductile shear zones of great lateral and vertical extent. Normally, several lenses occur in the same shear zone. The vein material seems to have resulted from incremental filling of openings by repeated vertical movement along rupture planes developed in the central part of the shear zones.The oblique veins are small elliptical lenses of ribboned vein material which formed essentially by progressive vertical opening of oblique fractures. Two types of oblique veins are known: one is restricted to feldspar porphyry dykes, within which they are arranged in an en-echelon fashion; the other is of greater extent and is not restricted to one rock type, but tends, however, to occur in the more competent porphyritic diorite.Vein orientation and mode of formation suggest that both sub-vertical and oblique veins developed during progressive deformation associated with the formation of the ductile shear zones. The latter probably formed in response to a compression that took place late in the tectonic history of the host rocks at Sigma."

Jan 1, 1983

By H. C. Gunning

SOME small vanadium-bearing deposits on the west coast of British Columbia about 100 miles north of Vancouver are of interest for several reasons. They are of a type that is, so far as we know, unique. They are difficult to identify as being vanadiferous so that, unless they are described, other similar deposits could easily pass unrecognized. Furthermore, although none of them has as yet been proven to be of commercial proportions, no good reason is apparent why larger, and therefore valuable, deposits should not occur under similar geological conditions. The original discovery on Quadra island was made in 1932 and has been recorded by H. V. Ellsworth and H. C. Gunning (l). Since 1932, prospecting in the area has revealed other similar deposits, one about a mile south of the original and another some ten miles to the east, near Menzies bay on Vancouver island. The Quadra Island showings are a mile and a half north of the head of Gowland harbour, a small inlet that is easily reached by gas boat from Campbell river, about four miles to the southeast on Vancouver island. The deposits were examined by the writers in the spring of 1943 in connection with field work sponsored by the Department of Geology, University of British Columbia. We are indebted to Mr. G. A. Dirom and Mr. Lothrop, of Vancouver, for helpful data on the Menzies Bay deposits, and to Dr. V. Dolmage for making a brief trip to Gowland harbour and discussing the deposits.

Jan 1, 1944