Search Documents

"The Waite-Amulet, an important copper-zinc mine, lies astride the Duprat-Dufresnoy township boundary about 8 miles northwest of Noranda, Quebec. It is an amalgamation of two properties, that of the former WaiteAckerman- Montgomery Mines to the north and that of Amulet Mines, Limited, to the south. This amalgamation took place in 1933. The description that follows is confined to the Amulet section.Ore was first discovered on the Amulet property in the autumn of 1924. The C Shaft and Upper A orebodies were found in 1925 and the F orebody in 1929, the latter by diamond drilling under a swamp. Under the present management, Lower A ore body was discovered by diamond drilling at a depth of 700 to 1,200 feet in 1938, and new ore was found from the old C Shaft workings between 1943 and 1945.From April 15th to October 20th, 1930, 60,291 tons of ore was produced from the Amulet. During the second half of this period, the ore averaged 4.2 per cent copper, 16.3 per cent zinc, and 0.02 oz. gold and 3.35 oz. silver per ton. Due to the prevailing low prices of metals, there was no further production until July, 1937. Output was greatly accelerated in 1940 when the newly found Lower A orebody assumed the main burden of production. Up to January 1st, 1946, mill reports indicate the treatment of the following ore: GENERAL GEOLOGYFig. 1 shows the geology of the entire property. To the east is the Lake Dufault granodiorite stock and to the west the Flavrian Lake granite mass. Around the granodiorite and separating the Waite from: the Amulet section is an older diorite intrusion. The ore occurs in a series of lavas that form a broad anticline pitching eastward at a relatively low angle into the Lake Dufault intrusives. There are several steep east-west faults. The late Powell diabase dyke is shown, also the general areas of strong dalmatianite alteration, a type closely associated with the sulphide mineralization."

Jan 1, 1954

By H. Lundberg

Introduction The world has been suffering from an excessive production of all kinds of raw materials, and the metals and petroleum are no exception. As a consequence, at the moment, the urge to find new mineral deposits is almost non-existent and prospecting languishes. But from previous experience we know that sooner or later new supplies will be needed. Mineral deposits become exhausted, and to keep up the supplies of our metals and petroleum, new deposits must be found. Even now, a supply of petroleum of domestic production would not be unwelcome in Canada. It is not, therefore, so entirely malapropos to discuss means of finding ores and oil as it would seem. Almost any physical property connected in definite manner with minerals and rocks may be made the basis of geophysical exploration. This is particularly true of electrical resistivity, and its utilization in electrical prospecting has been the deciding factor in the discovery of such big ore-bodies as Buchans mine, Newfoundland, and the large copper ore-bodies in northern Sweden, etc., as well as in the solution of many foundation and structural problems. The importance of electrical prospecting has been growing steadily, and already there exists hardly any exploration project involving geological problems which may not profit by its application. Electrical prospecting is marching on, and neither temporary failures, nor incompetence, nor over-optimism, nor ill-will and pessimism, nor bad times and business depression, will be able to halt its progress.

Jan 1, 1931

By Z. I. Zaki

Synthesis of TiC /A1203 Composite from TiO2, Al and graphite using combustion technique has been investigated at different initial temperatures; room, 400 and 600 °C. The effect of initial temperature on the composition of the product, wave velocity and combustion temperature of the reaction was studied. The measured combustion temperature and wave velocity were increased with increasing the initial temperature of the combustion reaction. The maximum wave velocity obtained was 5.9mms-1 when conducting the combustion reaction at initial temperature of 600 °C. Oxidation resistance of the obtained composite was also studied at the temperature range 300-800 °C. No oxidation is detected before 400 °C while it takes place effectively at 700 °C forming different titanium oxides. Wave velocity measurements method was used to calculate the activation energy of the reaction between the starting materials. It was found to be 316.34 kJ mol 1 at the temperature range that was studied.

Jan 1, 2007

By Claudio Rocha Rosales

"Peñoles is a mining group with integrated operations in the smelting and refining of non-ferrous metals, and is also a chemicals producer. Peñoles is the world’s foremost producer of refined silver, metallic bismuth and sodium sulphate and is the leading Latin American producer of refined gold, lead and zinc. The Met-Mex Peñoles Zinc Plant commenced operations in 1973 with an annual production capacity of 105,000 t/y. Year after year the production has been increased, and at present, the production capacity is 240,000 t/y. In this paper, the leaching process,particularly the operation of the jarosite circuit is reviewed ,specifying process improvements to treat high iron calcines.INTRODUCTIONThe purpose of the leaching process is to recover the metals, mainly zinc,through a series of extraction stages with sulphuric acid solutions, which progressively increase the zinc recovery. After the series of acidification stages,the solution, which is rich in iron, is sent to the jarosite circuit to separate the zinc from the iron (Garcia & Valdez, 1996).The first step of the leaching process is the neutral leach circuit which produces a zinc sulphate solution that is sent to the purification section for the removal of impurities such as cadmium, cobalt and copper, after this solution is sent to the tankhouse to feed the electrolytic cells."

Jan 1, 2016

By Arnold Blaisonneau, Théophile Guillon, Xavier Rachez, Sylvie Gentier

"L’étude présentée ici vise à étudier l’influence, lors de stimulation hydraulique de puits dans les réservoirs géothermiques de type Enhanced Geothermal System (EGS), du comportement mécanique des zones de failles recoupant le puits sur la réponse hydraulique du réseau de fractures 3D. Dans ce but, un modèle 3D, basé sur la méthode des éléments distincts et dans lequel les zones de failles recoupant le puits sont modélisées par des fractures numériques 2D, est mis en oeuvre. Les modélisations présentées ici visent à caractériser l’influence du comportement mécanique (type de comportement, hétérogénéité) sur la cinétique de la stimulation hydraulique, ainsi que sur son effet spatial autour du puits. INTRODUCTIONPour le développement de l’exploitation géothermique de type Enhanced Geothermal System (EGS), la phase de stimulation conditionne grandement le succés du projet ; en effet, elle a pour objectif d’augmenter l’injectivité et la productivité des puits et doit permettre d’assurer la connexion entre les puits d’injection et de production garantissant ainsi la viabilité technique et économique de l’échangeur. Pour le site EGS de Soultz-sous-Forêts (France), parmi différentes techniques de stimulation, la stimulation hydraulique a été utilisée à cette fin en provoquant une augmentation irréversible de la perméabilité autour des puits. Dans ce type de réservoirs fracturés, le but des stimulations hydrauliques est de réactiver, plus spécifiquement en cisaillement, des structures hydrauliques pré-existantes (fractures, zones de failles etc.) dans le socle cristallin. La compréhension des phénomènes physiques durant la stimulation hydraulique est cruciale pour optimiser cette technologie et pour contrôler/limiter les risques associés (viabilité technique et économique des puits, sismicité induite etc.). C’est notamment le cas pour la relation entre le comportement mécanique des structures stimulées et les conséquences sur le comportement hydraulique dans un contexte tectonique spécifique."

Jan 1, 2015

By P. G. Dunn, J. Fitzgerald

ABSTRACT The scheduling of underground mining activities is a complex task that must simultaneously satisfy a large number of constraints. A schedule optimization tool (SOT) for underground mine planning is described, and its use for investigating strategic decisions is illustrated through a case study. The maincomponents of the SOT include (a) a genetic algorithm that searches for optimal schedules, (b) guidance for the application of heuristic rules, and (c) sliding, which implements just-in-time development. Findings indicated that preliminary scheduling performed before invoking the SOT, intended to provide a good starting point for the search, did not ultimately lead to higher value schedules.

Jan 1, 2010

By D. D. Liu

This paper proposes a charge induction dust measurement method based on detrended fluctuation analysis (DFA) for use in coal mine environments, based upon electrostatic interference, dust properties, wind speed, particle size, moisture content and other factors. In this methods, sequence x(t) is first obtained through a dust concentration sensing probe, and then the cumulative deviation y(t) is calculated, and y(t) is divided into same lengths. Secondly, a first-order linear fit is used for data of each interval, and mean-square deviation filtered DFA was calculated for each interval. Finally, the dust mass concentration of the corresponding time is obtain by supplemented calibration coefficient and fitted the data point which is the mean and square root for all lengths of interval. Simulation and verification experiments showed that the charge induction dust measurement method based on DFA can reduce coal mine electrostatic interference effects with high accuracy. The design has been successfully applied to select areas.

Aug 1, 2013

By Juan Asalgado

The JORC and NI43-101 codes impose that mineralized material has a reasonable prospect of economical extraction to be classified as Mineral Resource. For deposits close to surface and amenable to open pit mining, it is easy to show reasonable prospect of economic extraction running a Lerch-Grossman optimization. The Lerch-Grossman pit provides a transparent and repeatable way of separating the Mineral Resource (within the pit) from the remainder of the mineral inventory (outside the pit). Deposits amenable to underground mining are more challenging because of the variety of the underground methods. AMEC developed a stand-alone software package that outlines the material which has reasonable prospect of economic extraction for open stoping, block caving, sublevel caving and room and pillar. The software takes a block model file in ASCII and exports a 3D surface outlining the part of the mineralization that has a reasonable prospect of economic extraction, and which the Qualified Person can smooth out manually if required.

Oct 1, 2009

By B. Tiryaki, M. Ayhan, O. Z. Hekimoglu

Coal shearers are one of the major sources of dust and fines in underground coal mines. Despite considerable research investigations, no comprehensive in situ investigations coupled with extensive laboratory studies on the effects of drum design on generation of dust and fines have been found. It may be for this reason that many major shearer drum manufacturers persistently employ a certain drum-lacing pattern on current coal shearers, which is believed to cause excessive dust and fines in coal mines. This paper shows how respirable dust and fines are minimized under near-identical conditions when the drum lacing pattern was changed from a triple-tracking to a single tracking arrangement. A series of laboratory trials simulating in full scale the practical cutting action of tools was followed by extensive long-term underground trials during production operations in OAL (Cayirhan) Lignite mine in Turkey. The results are presented and discussed, and recommendations for proper drum-lacing in terms of respirable dust and fines are made.

Jan 1, 2002

By M. Lindgren, M. Latva-Kokko

Process performance can be significantly influenced by proper design of hydrometallurgical reactors. Optimal reactor configuration is case specific and depends on process requirements such as reaction rate limiting factor and particle size distribution. Choice of materials and manufacturing methods also play important roles in highly corrosive and abrasive environment often involved in hydrometallurgical industry. In this paper performance of different reactor designs has been compared in some typical hydrometallurgical applications. Results show that significant improvement in energy consumption, gas utilization efficiency and equipment lifetime can be achieved with process specific reactor design.

Jan 1, 2014

By Leslie Gertsch

Outline First progress report ? ?Introduction ?Non-terrestrial mining ?Near-term targets ?Stages of mining ?Study procedure Capabilities needed for non-terrestrial mining ?Mining methods ?Mining unit operations ?Typical surface mine operations sequence ?Results to date General effects of gravity ?On fragmentation ?On excavation ?On transport ?Conclusions / Recommendations

May 1, 2013

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By Mary Kama, Kaul Gena

"Magnetic skarn ore (MSO) is one of the major copper bearing ore extracted by the Ok Tedi Copper Mine in Papua New Guinea. Copper minerals are recovered by flotation while the iron not associated with copper are discarded as tailings. The objective of this investigation was to determine the iron ore reduction kinetics for the Ok Tedi MSO and ascertain if it can be processed to produce sponge iron for a mini steel plant in Papua New Guinea.SEM-EDAX analyses of the Ok Tedi MSO indicated 10.1% C, 30% O, 0.6% Mg, 1.1% Si, 21.1% S, 0.8% Ca and 36.2% Fe. Most of the iron is in sulfide form. Both naturally occurring and roasted sinters of Ok Tedi MSO samples of different particle sizes were reduced by charcoal carbon at three different temperatures and seven different reduction times. Analyses of the reduced products indicated a metallic iron content of more than 65 wt.% on average.Results showed that there was no significant difference in reduction between fluxed and control materials. Only a slight increase in kinetics with reduced particle size, hence the reaction rate constant (K) did not vary much within the temperatures investigated. Reaction kinetics increases with increasing reduction time at 900°C. Therefore, more iron reduction is observed with particles of 106 µm size. In addition, the results also confirmed that the reduction energy used was higher at 800°C and lower at 1,000°C. In summary, iron reduction can be improved but close monitoring of temperature and reduction times are essential to determine the reaction kinetics of the Ok Tedi MSO. INTRODUCTIONMost mines in Papua New Guinea mine large quantities of iron in the form of sulfides, carbonates, oxides and sulfates that are eventually disposed off as tailings. The Ok Tedi magnetic skarn ore (MSO) contains a significant amount of hematite, magnetite, siderite, ilmenite and pyrite that can be a source of iron. The mineralogical compositions of Ok Tedi MSO reveals more iron minerals than copper, yet all iron containing minerals are collected in the tails from the main copper production stream. Therefore, this study is conducted to investigate the possibility of producing direct reduced iron (DRI), or sponge iron, from the MSO. Such sponge iron may serve as the feedstock for electric arc/induction furnace based mini steel plants in Papua New Guinea."

Jan 1, 2016

By Lang Tao, Jun Wang, Wei Xiao, Wenqing Qin, Pan Cao, Guanzhou Qiu, Key Lab of Biohydrometallurgy of Ministry of Education, Central South University

"The effect of metal cations on the rutile flotation using styryl phosphoric acid (SPA) as the collector was investigated by micro-flotation test, bench scale flotation test, zeta-potential measurements and adsorption measurements. The micro-flotation results indicated that Fe (?) and Al (?) ions in low concentrations had obvious activation on the rutile flotation, and Pb (?) ions in low concentrations had smaller activation of rutile, but Fe (?), Al (?), Pb (?), Ca (?) and Mg (?) have strong inhibition of rutile flotation in high concentrations. The bench scale flotation results indicated ethylene diamine tetraacetic acid (EDTA), boracic acid, and sodium hexametaphospate can decrease the metal ions concentrations, and increase the recovery of rutile flotation. Adsorption measurements and zeta-potential measurements revealed that Fe (?), Al (?) and Pb (?) ions were adsorbed on the rutile surface, and had interaction with SPA. But when these ions concentration were over the largest adsorption capacity, residual metal ions could occur chemical reaction with SPA.INTRODUCTIONRutile is one of the favored minerals for production of titanium dioxide white pigment, primarily through the chloride manufacturing process (Stanaway 1994; Hou et al., 2013) However, the majority of rutile ores belong to refractory ores, while flotation is one of the most efficient methods to separate fine rutile from gangue (Dolbear et al., 1937). With the flotation development, many effective collectors were successfully applied in the oxide ore. Many reviews have indicated that organic phosphonic acid collectors showed good selectivity on oxide ores such as ilmenite and rutile (Bulatovic & Wyslouzil 1999; Liu & Peng 1999).It is inevitable that many types of metal cations are present in ore pulp. These metal cations significantly influence the flotation of minerals. Liu et al. (2015) showed that Ca2+ and Mg2+ could improve the floatability of spodumene at pH 12.5 and 10.0, respectively. The authors proposed that Ca2+ and Mg2+ ions readily form hydroxy complexes (CaOH(l) and MgOH(l)) and precipitates as (Ca(OH)2 and Mg(OH)2) in strongly alkaline solutions. Fan and Rowson (2000) investigated the effect of Pb(NO3)2 addition as an activator on ilmenite flotation and showed that it could improve ilmenite floatability. The addition of Pb(NO3)2 resulted in an increase of ilmenite zeta potential in both weakly alkaline and acidic aqueous solutions. Mehdilo, Irannajad, and Rezai (2015) studied three kinds of ilmenite of different origins and discovered that both Mg and V had a negative correlation with ilmenite flotation, while the Mn content seemed to correlate positively with flotation efficiency. A number of studies have also showed that Fe3+ can improve the floatability of ilmenite (Fan et al., 2009; Nuri, Mehdilo, & Irannajad, 2014)."

Jan 1, 2016

By D. J. Xue

Four kinds of coal-rock combination were subjected to three kinds of stress waves in the SHPB numerical simulation. The wave propagation and the changes of the strain energy in the coal-rock combination during the dynamic impact process were recorded as well as the contact force. The dynamic response law of coal-rock combination was obtained. It was found that the coal had better reflectivity than the rock because of coal with larger impedance. In contrast the rock had better transmissivity. As the crest value of the incident wave increased, the increment in the crest value of the transmitted wave weakened in the coal-coal group, coal-rock group and rock-coal group, in contrast, the increment in the rock-rock group increased.

Aug 1, 2013

By G. W. Poling

Sedimentation behaviour of siliceous mill tailings derived from a magnetite-chalcopyrite ore in fresh water, fresh water - sea water mixtures and full-salinity sea waters are compared. Results of batch settling tests are presented in the form of settling curves and solids flux curves. The addition of a few per cent of sea water markedly enhanced the zone sedimentation rate due to particle agglomeration caused by a reduction in zeta potential of the suspended solids. The presence of a small amount of residual, previously magnetized magnetite in the tailings also enhanced agglomeration and sedimentation. The significance of these results to submarine disposal of mill tailings is discussed.

Jan 1, 1973

By H. A. Kee

In the mining industry, as in other business, one of the more satisfactory results of sincere but cheerful effort lies in the proper completion of undertakings and problems, which, to be successful, must continually hold the interest of all concerned in the work. In most undertakings, genuine interest and satisfaction is largely dependent on the proper appraisal of opportunities presented, and the opportunity to associate ourselves with sinking operations at McIntyre central shaft, from the surface to a depth of 4,133 feet, was genuinely appreciated. This opportunity was made possible by the previous persistent and successful leadership of Mr. J. P. Bickell, President, with the assistance of his associates, and of the general manager, Mr. R.J. Ennis, in the development of the McIntyre Porcupine mine, and I beg to state that any success in this sinking operation was very largely due to the congenial co-operation and splendid workmanship of Captain Martin C. Horne, his shift bosses, leaders, and all those who worked with us . Our slogan throughout was " Safety First for Pleasant and Efficient Workmanship," and this general policy made it possible to sink and timber 2.,123 feet during the first year without a serious accident.

Jan 1, 1928

By M. Turner-Jones, N. Steenekamp

"The Lonmin Base Metal Refinery treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode as well as a concentrate containing the platinum group (PGM) metals. The original process employed a Sherritt design and utilizes atmospheric and pressure leaches for the dissolution of base metals. This paper describes the original flow sheet and the improvements made to enhance PGM recoveries, product quality and to increase capacity. Changes include the introduction of flash recycle cooling on the autoclave, batch leaches to improve the quality of the PGM concentrate and the implementation of solid-liquid separation with centrifuges. INTRODUCTIONThe Lonmin Base Metal Refinery (BMR) is about 100 km north-west of Johannesburg and treats converter matte from the Lonmin Smelter to produce nickel sulphate crystals, copper cathode and a concentrate containing the PGMs. The plant was commissioned in 1985 based on a Sherritt design to treat 12 tonnes converter matte per day. The original flow sheet consists of a milling circuit, an atmospheric leach and a pressure leach to produce a PGM concentrate which is despatched by helicopter to the Lonmin Platinum refinery in Brakpan, about 40 km east of Johannesburg. The liquor from the atmospheric leach is treated by crystallization to produce a nickel sulphate hexa-hydrate crystal. The leach liquor from the pressure leach is treated by a selenium removal step followed by electro-winning to produce copper cathode. The spent solution from the copper electro-winning is recycled to both the atmospheric and pressure leach steps to provide sulphuric acid for the leaching reactions.Modifications were made to the original circuit to increase the plant capacity, to improve the PGM recoveries and to improve the quality of the PGM concentrate. Capacity increases included all the unit operations, new mill, new first stage, additional autoclaves, additional nickel sulphate crystallizers, new copper electro-winning and new batch leach reactors for upgrading the PGM concentrate. The current circuit is described in this paper and not the detailed history of each plant change."

Jan 1, 2012

By A. van As, J. McGaughey, M. J. Mol, R. Tosen

Geotechnical monitoring is a key element of the successful management of a block cave mine. The interrelationships between production and various monitoring datasets are often not realized due to a lack of data integration and appropriate 3D visualization. Timely delivery of information to ensure best cave management practices is only possible with an integrated cave management system. At Rio Tinto, a state-of-the-art cave management system (CaveCAD) has been designed and developed in cooperation with Mira Geoscience to integrate and analyze vast datasets and report this as instructive information regarding the current \u201cstatus\u201d of the cave.

Jan 1, 2014

By M. Askari, A. Ahmadi

"This study was conducted to establish the possible application of bioleaching in the pilot scale to recover valuable metals from the sulfidic tailings of Golgohar Iron Mine (Kerman, Iran). Using bioleaching processes, solvent extraction and sulfide precipitation recovery of valuable metals including, copper, cobalt and nickel from the tailing was investigated. The results showed that the optimum pH and temperature conditions relative to the bioleaching step was 1.5 and 45°C. The extraction of the metals from the low grade polymetal resource with complex mineralogy is very important from economic, environmental and technical point of views. Moreover, the proposed method has some advantages from energy saving, tailing management and creating added value from waste materials aspects.INTRODUCTION The growing demand for base metals and strategic such as: copper, nickel and cobalt as well as high-grade resource depletion has caused them, the mining industry to extract metals from low-grade resources and driven by complex mineralogy (Xie et al., 2005). Economic extraction of metals with low grade sources requires low-cost and efficient processing methods. A source with enormous potential for metals in future, secondary sources, such as: tailings mineral industries which the lack of appropriate technology and the high cost of processing weren't recoverable with previous procedures in the past. But it is possible that with develop new and efficient technologies have the economic exploitation ability. Recovery of metals from tailings resources is very important not only in terms of precious metals but also in terms of reducing environmental problems (due to heavy metals). The metals of copper, nickel and cobalt are mainly like sulfide compounds in the nature, usually for their recovery, first they make ore with flotation method to obtain the sulfide concentrate that containing valuable metals. then for the metal production, it will be melt and purification. Due to the environmental aspects, technical problems in the recovery of base metals from low grade ore and mixes, the presence of small reserves, in the past three decades they pay much attention to the use of hydrometallurgical processes for the recovery of base metals from these resources. These processes are classified according to the solver agent to leaching sulfates, chlorides, nitrates and amines (Hackl, 1995). Early, chloride leaching under oxidation condition in acidic or alkaline solutions was recognized the best process to produce sulfide concentrates. But then the basic processes sulfates was considered as the superior process because of being easier, a better understanding of the chemistry of leaching and recovery of base metals, especially copper from the environment easier sulfate solution with an organic solvent extraction and electro winning. The bioleaching is shown its ability on a commercial scale of low-grade sulfide minerals and ore that because of environmental reasons, the possibility of melting is not possible to them. The existing industrial base factories are based on primarily on the bioleaching and pressure leaching and recovery of cathode copper sulfate solution by extraction with organic solvents (SX) and electrowinning (EW) (Wang, 2005). Preliminary analysis has shown that valuable elements such as copper, nickel and cobalt are in the float flotation unit. Hence the plan to extract these metals from the wet tailing stream has been done."

Jan 1, 2017