Search Documents

By A. Koster, V. Maurel, S. Dezecot, Szmytka. F.

The aim of this work is to clarify the role of microstructure heterogeneity in the initiation and growth of cracks in a lost foam cast A319 for low cycle fatigue (LCF) loading condition. Because 2D analysis fail to establish the scenario of damage events, this study is based on 3D in situ analysis using synchrotron X-ray tomography during LCF test performed at 200°C. If X-ray tomography is now an established technique to study damage development in 3D, its application for relatively high temperature cyclic tests has never been done so far. Initial 3D observations of damage show that the cracks that lead to fracture initiate near large pores and propagate into the hard particles 3D network of the eutectic regions.

Jan 1, 2015

By T. Iwasaki

This paper points out two key elements in resource trade in general and the Canada-Japan relationship in particular. The first is that the advanced countries have a more important role than one would expect in the supply of resources in world trade. Canada 's dual role as a major resource supplier in conjunction with an advanced economy will continue to increase. The second point is the heavy reliance on foreign resource supplies in some advanced economies, particularly in Japan. Finally, as regard the future of the Canada-Japan economic relationship, particularly .in resource development, it is suggested that trade could be enhanced by an accelerated exchange of various types of resources between the two countries. These include natural resource commodities as well as the more abstract capital, technological and human resources.

Jan 1, 1978

By Norman Marr

Introduction In Canada, the mining industry and water-power development are intimately associated in that mining, which ranks second among the country's primary industries, depends principally upon hydro-electric energy for its large power requirements. On the whole, the Dominion has been very favourably endowed with water-power resources; generally speaking it is a well-watered country with numerous rivers and lakes located in are as where the topography favours water-power development. Precipitation, the raw material of water power, varies from an annual fall of more than l00 inches on the Pacific coast to about 12 inches in sections of the Prairies and the Northwest Territories; in Ontario and Quebec the annual average is 24 to 40 inches and in Nova Scotia about 45 inches. In its descent to the sea, the resulting run-off, much of it from considerable altitudes, creates sources of potential energy at every rapid and fall along the country's many streams and rivers. Many of the innumerable lakes in the Dominion provide storage basins for the regulation of stream flow, thus enhancing the potential power of available sites. While water-power resources are fairly well distributed across the Dominion, as is shown on the accompanying map of Canada showing power sites (Figure 1), it is particularly fortunate that those areas which are lacking in indigenous fuels have been compensated in large degree for this scarcity by being favoured with a high proportion of the total potential water power. This has an important bearing on the mining industry in that extensive mining operations can be economically carried out in the great Canadian Shield, which is lacking in commercial coal deposits but is rich in water-power resources. This Precambrian formation, which forms a wide belt around Hudson bay and in which many metalliferous ores are found, was 'subject to severe glaciation in a recent geological period, so that its river systems are comparatively young and are characterized by numerous lakes joined by short reaches of fast water, rapids, and falls which offer frequent opportunities for power development. The western Cordilleran region, which also is important in mining, has abundant water power. The accompanying geological map (Figure 2), prepared by the Geological Survey of Canada, shows the great extent of the Precambrian and Cordilleran regions and may be compared with the map of water-power sites to show the high incidence of water-power resources in these potential mining areas in which important mineral discoveries have already been made.

Jan 1, 1949

By P. Cain, B. Martens

"Grande Cache Coal (GCC), an investor-owned Alberta company, is in the final stages of the regulatory process leading to the resumption of coal mining in the Smoky River Coal Field of Alberta. Although many opportunities for low-cost, high-yield mining remained on the property, GCC opted for a long-term production plan that ensures stability for the local economy, sustainable use of the resources in the area, environmental responsibility and a satisfactory return for its investors.GCC entered the Alberta coal approval process in late 2000 with a public disclosure document. In October 2001, GCC formally submitted an application for mining approval and an environmental impact assessment (EIA) to the government and the public. The application covered the proposed Grande Cache Coal project, which includes the No. 7 underground mine, No. 8 surface mine and coal processing operations. The EIA provided a comprehensive investigation of environmental sensitivities in the project area, matched with environmental protection programs. The project is based on commencement of operations in late 2002. GCC’s plans are founded on a commitment to sustainable development and has framed this commitment in the context of a long-range mine development plan that will sustain the community of Grande Cache over the next 25 years. The Grande Cache coalfields offer extensive coal reserves and opportunities, for both surface and underground mining. Combining highly productive U.S.-style room and- pillar underground mining methods and conventional truck-and-shovel open pit mining, GCC’s approach to sustainable development encompasses community involvement and reclamation of mine sites to productive land uses after mining."

Jan 1, 2002

By Marcel Vallee, Fernand Dubuc

"The St-Honoré carbonatite complex, located 8 miles north of Chicoutimi, Quebec, was discovered in September 1967 as abnormal radioactivity was detected in the course of SOQUEM's aerial surveys. The complex, covered by a shallow layer of Trenton limestone, has been explored by aeromagnetic, ground gravimetric and magnetic surveys, and 12,013 feet of diamond drilling. Its age, from potassium-argon dating, is 650 million years. The carbonatite is approximately kidney-shaped and has a surface area of 6 square miles, 20 per cent of which is explored. It shows a central core of coarse-grained massive dolomitic carbonatite and an outer ring of foliated dolomitic carbonatite.The exploration work to date has resulted in the discovery, in the foliated carbonatite, of an incompletely drilled niobium (columbium) zone of pyrochlore-bearing carbonatite, at least 1,000 by 800 feet in size. This zone contains 5,000 tons per vertical foot grading 0.86 per cent Nb205 or at least 15,000 tons per vertical foot grading 0.66 per cent Nb205 or 45,000 tons grading 0.48 per cent Nb20s. The pyrochlore contains an average of 64 per cent Nb,Os. The central core contains a zone of rare-earth-bearing carbonatite (as monazite), grading up to 4.5 per cent rare-earth oxide, 3,500 ppm zinc and 290 ppm molybdenum. Stocks of nepheline syenite and magnetite diorite accompany the carbonatite. The total analysis and trace-element contents of typical rocks are presented."

Jan 1, 1970

By Witold J. S. Ostrowski

The shaft structure being part of an underground mine, depends on programned functional duties, and on geological and hydrological conditions. The majority of Canadian metal mine shafts are in hard competent igneous rocks, which are in an elastic state of equilibrium around the excavation. Others penetrate soft sedimentary or very weak water-bearing rock formations in which the equilibrium varies from plastic to hydrostatic. Knowledge of how to interpret the underground conditions, determine acting forces and design proper structures is essential for the production and safety of the future mine.

Jan 1, 1973

CONSTRUCTED WETLANDS (CWs) ?Human-Constructed ?Built Specifically to Remove Contaminants ?Can Treat a Wide Variety of Wastewaters Including Stormwater(SW) ?Three Major Kinds ?Pond Wetlands ?Free Water Surface Wetlands (FWS) ?Sub-Surface Flow Wetlands (SSF) ?HSSF & VSSF

May 1, 2009

By A. Ignatieff

This is the second review of developments in coal mining engineering (see C.I.M .M. Transactions, Vol. LI, 1948, pp. 262- 264) and covers the period from October, 1948, to January, 1950. Mechanization The period under review was characterized by the intensive development of appliances providing for complete mechanization of coal-face operations. A variety of machines are being evolved or have already been placed on the market which embody the principle of 'continuous mining'. This trend can be observed in all coal producing countries. In the United States, two continuous mining machines have been developed for entry and room application and by the end of 1 949 were being used in a number of mines. These are the Joy Continuous Miner in which the coal is ripped from the face by means of multiple cutter chains, and the Jeffrey Colmol employing cutters on rotating arms for chipping the coal from the face. The Joy machine is made in tw6l models, 34-in. and 48-in. high and designed for a range of seam thicknesses from 3-ft. -t-in. to 4-ft. 6-in. and from 4-ft. 6-in. to 8ft., respectively. Some experience has been gained with this machine and accounts of its performance are already appearing in the technical literature. The Jeffrey-Colmol has a more limited range of working height. The first model, 38-in. high, was designed for seams about 4 feet in thick11ess but more recently the 28-in. low model has been placed on the market for seams 2-ft. 6-in, to 3-ft. 4-in. in thickness. Conventional mobile loading machines of the gathering-arm type are continuing to yield high production under suitable conditions, and improvements or modifications of the basic principle are embodied in new machines as, for example, the Jeffrey mobile (conveyor) loader with extensible (gathering-arm) head developed for conveyor mining.

Jan 1, 1950

By S. L. Gertsman

Canadian steel foundry practice has made marked progress during the past decade. Equipment suppliers, development engineers, and foundry personnel have focussed their attention on every phase of the foundry operation, with a resulting lower demand on manpower and materials. Also, more rigid specification requirements as to dimensional tolerances and quality have necessitated improvement and increased control at every stage from the pattern shop to the cleaning room. The growing trend toward mechanization is clearly evident. Equipment such as sand mixers, sand reclamation systems, material handling devices, moulding machines, core blowers, etc., is being increasingly employed by the steel foundryman. This equipment not only increases production but also tends to lessen the human variable so prevalent and disconcerting in the early days of steel founding. The result has been an improved and more reliable steel casting, which is gradually obtaining wider acceptance by design engineers. The purpose of this paper is to discuss briefly some of the practices being used, and also the direction of development that is being pursued by Canadian steel foundrymen.

Jan 1, 1948

By C. M. Offenhauer

Abstract Zirconium markedly affects the formation of graphite in cast iron and may promote the formation of normal flake gaphite, fine flakes of eutectiform graphite, or spheroid nodular graphite, according to the composition of the Iron and the amount of the zirconium addition. Usually, it is employed in the form of a complex addition agent in order to facilitate its introduction and to guide its effect. The reported applications of zirconium as an inoculant for the production of pearlitic high-strength cast iron indicates that it is most effective as a silicon-manganese-zirconium alloy. Added in this form it reduces chill and minimizes zones of ferrite and eutectiform graphite. In low-sulphur cast iron, zirconium in amounts greater than 0.10 per cent tends to promote the development of eutectiform graphite. These irons are characterized by freedom from primary cementite or normal flake graphite and exhibit very little tendency to shrinkage on solidification. In hyper-eutectic low-sulphur cast iron, zirconium causes the formation of a partially nodular graphite structure. A combination of magnesium with silicon-zirconium alloy was found to produce completely nodular graphite structures without the hazards associated with the addition of elemental magnesium.

Jan 1, 1949

By F. O. Verret

Several grindability tests were developed over the years to design grinding circuits or optimize existing operations. Each test has its own strengths and weaknesses and it is imperative to select the proper test procedure(s) to meet project deliverables and minimize the risk of a project. Pilot plant testing of large bulk samples historically constituted the traditional approach for AG or SAG design, but was gradually replaced by small-scale tests. Nowadays, conducting grindability tests requiring only a few kilos of material on several samples is a more typical approach to grinding mill design. This paper summarises the requirements and deliverables of various bench-scale test procedures, their strengths and weaknesses, and cases where AG/SAG pilot testing should still be performed.

Jan 1, 2012

The principles and utility of in-situ coal gasification are discussed, and a first field test conducted by the Alberta Research Council in 1976 near Forestburg, Alberta, is described. The test was carried out in a 12-ft subbituminous coal seam under 60 feet of cover. Within this seam, a 30 by 60-foot block , containing approximately 650 tons of coal, was delineated by four injection/production holes which were oriented to take advantage of the natural fracture system in the coal. Linkage between holes was established by reverse combustion and gasification was accomplished by injecting air into the ignited coal. No steam was injected but operating pressures were adjusted to utilize formation waters for partial carbon -steam gasification. The coal gasification runs lasted six weeks and gasified an estimated 900 tons of coal ,' during sustained periods of gasification, a fuel gas with heating values of between 110 and 150 Btu/scf was obtained. Plans are now being developed for excavating the test site and inspecting the subsurface cavities created by gasification.

Jan 1, 1977

By J. Duby

"A description is given of a series of tests performed to determine the comparative effects which dynamic and static straining, in compression, have on the physical strength properties of mild steel and an aluminum alloy. The dynamic deformation was imposed during the passage of single stress pulses of about 100 micro-second duration. These pulses were recorded with strain gauges mounted near both ends of the specimen. The resulting records were analysed using a simple wave theory; there from the dynamic stress-strain curves for the respective metals were deter-mined and were then compared with the static stress-strain relation. The respective hardnesses of the metals after deformation are evaluates by means of static stress-strain curves in compression. The micro-structures of the metals before and after deformation are also shown. It is observed that dynamic de-formation considerably modifies the rate of strain hardening. This modified hardening appears to be persistent. The observed differences in physical strength properties and micro-structures are discussed in the light of the accepted dislocation theory for metals."

Jan 1, 1960

By M. G. Lipsett

"The Mining Information Technology User Group considers information to be a strategic enabler to improved business performance in mining. This ad hoc group has been meeting since 2000 to share knowledge and leverage their efforts in effectively using IT in mining. In this paper, core issues to mining IT are reviewed, along with initiatives to engage industry professionals and decision-makers in the potential for improved use of information in their operations. Relevance of IT to Canadian MiningMining operations always drive to improve their performance, and so far they have succeeded by using different technologies. While economies of scale have come in fragmentation and material handling, and energy usage has improved through conservation and design of integrated mineral processing plants, these systems have the net result of tightening operational constraints, through reduced excess capacity. There are higher opportunity costs of lost production when integrated, large-scale systems are operating in a sub-optimal way.The problem is that it is profoundly difficult to run a mine in an optimal way. Optimization requires a defined objective function (e.g., profit), which is hard to pose, let alone solve, because so many inter-related aspects of an operation affect the bottom line. Even for a small, well-defined process state, it is difficult to measure all the pertinent information with sufficient accuracy to ensure that the system is performing well in real time.The art of mining remains making good decisions with uncertainty: in the orebody delineation; in the allocation of resources; in the efficiency of the operation; in the reliability of components and systems; and in responding to the downstream market. As well, individual decision-makers need to know how their decisions affect other processes and systems, so that improvements in one part of an operation do not result in such degraded performance in the rest of the plant that overall profitability goes down."

Jan 1, 2003

By R. C. A. Thurston

Introduction A mechanical spring has been .defined by Wahl ( 1) as 'an elastic body whose ?primary function is? to deflect or distort under load, and which recovers its original shape when released after being distorted'. Most material bodies are elastic to some extent ? and will deform under load, but they are seldom regarded as springs since this is not their primary function. The principal applications of springs are the absorption of energy and the mitigation of shock, the support cf moving masses or the isolation of vibration, and the provision or measurement of definite loads or torques. A large number of spring types have been developed to serve these purposes and to meet the different operational requirements; they range from the large semi-elliptic leaf suspension spring to the delicate watch hairspring. The springs of most importance in machine design, however, are the helical round-wire compression or tension types. They are made in a wide variety of sizes and are used in tremendous quantities, mainly because of their low cost, their compactness, and their relatively high efficiency. Their field of application is as broad as that of machine design itself, but the bulk of production is almost certainly for suspension systems of vehicles such as automobiles, freight and passenger cars, and mine cars, and it is with the last of these applications that this paper is primarily concerned.

Jan 1, 1951

By Ian McC. Stewart

"Seam gas flow in coal mines takes place through a medium which has both capacity and resistance and can therefore be expressed in terms of the basic diffusion equation, provided that the characteristics of the system can be adequately described. It may be possible to lump the variations from point to point in a seam together as an effective diffusivity. The paper discusses the characteristic flow-time patterns for various types of openings and the particular features of coal and seam which influence the diffusivity.Two field experiments are described in which gas make to a heading and to a borehole were measured in a mine for which considerable data on coal sorption properties were available. Incremental gas flow measured from the borehole experiment predicted the actual flow from the heading measurements remarkably well. The effective permeability adjacent to the face was much higher than expected from the properties of the coal. The incremental flow measurements to a horizontal (in-seam) borehole showed a striking picture of advancing 'relaxation' behind the face which is not discernible by other experimental means."

Jan 1, 1971

By W. S. Hegler

Introduction The San Antonio mine is on the north shore of Rice lake, thirty miles east of lake Winnipeg and 120 miles northeast of the city of Winnipeg. Since production was started in 1932, about 2,000,000 tons of ore have been mined. Currently in progress is an extensive development programme which involves 11,500 feet of crosscuts, 3,800 feet of raises, 1,753 feet of shaft sinking, and 160,000 cubic feet of slashing, all in footwall waste rock. It is the purpose of this .paper to indicate the necessity for this work and to describe the methods employed to carry it out. Where unknown factors are as prevalent as they are in the average Canadian gold mine, a definite answer cannot be given as to what is the most economical and efficient system for mining dipping deposits. At San Antonio, the host rock for the orebodies, locally termed basalt, occurs as a sill some hundreds of feet in width and dipping at approximately 45 degrees from surface to an unknown depth. It may be assumed that it continues well below the lowest depth established to date by diamond drilling. At present, a vertical winze (No. 3 winze) hoists the ore from the 2,360-foot level to the 1,600-foot level, on which it is hauled about 900 feet to No. 3 shaft, also vertical, and there hoisted to the mill bins on surface. To maintain ore reserves at a five-year figure, at full production, additional deep exploration was required immediately. It was decided to sink No. 4 winze, a vertical opening of the same size as the other operating shafts, to provide ten additional levels (17 to 26) at 150-foot intervals, with additional depth to allow for an underground crusher installation and usual loading-pocket facilities for three-ton skip-hoisting. The winze was bottomed at 1,753 feet below the collar, at a depth of 4,117 feet below surface, and is the deepest man-sized opening in Manitoba.

Jan 1, 1949

By Marc Arpin

La Bolivie possède tout pour réussir. Son vaste territoire de plus d'un million de km2 et qui occupe une position stratégique au coeur du continent sud-américain recèle des ressources naturelles (forêts, minéraux, gaz naturel, etc) variées et abondantes. Elle a une frontière avec pas moins de 5 pays dont le géant que constitue le Brésil ainsi qu'avec l'Argentine, l'autre puissance régionale. Pourtant, malgré tous ces atouts, la Bolivie demeure l'un des pays les plus pauvres du continent. Ce paradoxe n'est nulle part mieux reflété que dans le secteur minier. Celui-ci fait face à une situation de crise en dépit d'une tradition minière de plus de quatre siècles et d'un potentiel géologique indiscutable ayant conduit à la découverte et à l'exploitation de fabuleux gisements d'argent et d'étain. Les habitants des districts miniers vivent dans des conditions de pauvreté extrême et les indicateurs de développement humain de ces régions sont parmi les plus bas en Amérique du Sud. La Bolivie réussit difficilement à attirer les compagnies minières alors que, chez les voisins, et particulièrement en Argentine, qui n'a pas de tradition minière, les investissements miniers majeurs affluent. Dans cette conférence, nous chercherons à expliquer les causes de cette situation et proposerons des solutions possibles.

May 1, 2001

By Hans Lundberg

Introduction Today, geophysical exploration is recognized as a special science wedged between geology and mining. Universities and technical institutes have special professors teaching geophysics applied to oil and ore prospecting. The list of literature on geophysical exploration has grown from practically nothing at all some twenty-five years ago to ~ several thousands of books, some of them very imposing volumes. Most of the methods now used have been developed since the first World War, and very large systematic exploration campaigns have been carried out in many places, in many countries. It has been rather difficult to obtain enough information as to what is going on in Canada. However, since the Associate Committee on Geodesy and Geophysics of the National Research Council became more actively engaged in promoting geophysical research, it may be easier to obtain information and, in the future, the quarterly issued Canadian Geophysical Bulletin may throw considerable light on the current geophysical activities in Canada. Some twenty crews have been engaged the last few years in geophysical prospecting for ore. In the United States, between 500 and 600 crews are employed exclusively in geophysical prospecting. Most of these, however, are engaged in oil exploration. During the winter 1942-1943, the German Government employed some fifty crews on geophysical exploration, and some ten crews were working for private enterprises.

Jan 1, 1948

By A. G. Eccles

"INTRODUCTIONWestern Mines' copper-lead-zinc operations are located in Strathcona Provincial Park, near the geographic centre of Vancouver Island. This park includes Buttle Lake, which flows into the Campbell River water system. The latter provides domestic water for the Town of Campbell River, approximately fifty-eight miles from the mine site.Operation of the concentrator commenced in December 1966, at which time the tailings were discharged into a small tailings pond near the plant. On May 8, 1967 Permit No. 185 was granted to the company, allowing discharge of the tailings, through a submerged outfall, to the bottom of Buttle Lake.Needless to say, the concept of operating a mine within a park, and the discharge of tailings into Buttle Lake generated considerable controversy. However, this has all but been eliminated over the years by the proven effectiveness of Western Mines' pollution control program. In 1973 this program was further upgraded with the addition of an alkaline chlorination plant. Effluent treatment by this method became necessary as a result of process modifications, and has been effective in maintaining the levels of characteristics in the tailings within the ever increasing pollution control requirements imposed on the industry."

Jan 1, 1977