Search Documents

By Tony Lipiec, Chris Fleming, Larry Urbanoski

In 2009, the Canadian Mineral Processors (CMP) became aware that Canadian securities regulators were amending the contents of National Instrument 43-101. NI 43-101 is a set of regulations which establish how ore resources and reserves are presented to the investing public. The documents produced under NI 43-101 are central to the ability of many companies to raise financing for their projects. With the increase of metallurgical complexity, and decrease of head grades encountered in new deposits, the role of the Qualified Person (QP) in determining process performance has become increasingly critical in determining the classification category of resources and reserves. Given the challenges confronted by those involved in defining the concentration and extraction of minerals and metals, there is a need to provide support to these QPs. To address these concerns, the CMP established a sub-committee in 2010 to create a set of guideline documents to assist the QP involved in process matters as to what should be included at the various levels of study supporting the establishment of resources and reserves in NI 43- 101. The results of the sub-committee work are presented and the considerations in the writing of the documents are discussed.

Jan 1, 2011

By Tom Olsen, Tom Ohrling, Peter Taggart, Chris Martin

"North American Palladium commissioned the new concentrator at the Lac des Iles mine in the summer of 2001. The 15,000 tonnes per day mill replaced the existing 2,400 tonnes per day facility, as part of a major mine expansion.At Lac des Iles, the grain size distribution of the platinum group minerals (PGM) is bi-modal. Roughly two-thirds of the PGM are relatively coarse-grained, and often associated with fast floating copper and nickel sulphides. The remainder is ultra-fine, and locked in silicates, which poses a special challenge to the metallurgist. The previous mill typically recovered just the fast-floating mineralisation, but to achieve target recoveries, the new mill has to recover a substantial amount of the ultra-fine PGM. The metallurgical challenges associated with the recovery of fine-grained PGM in the talcous Lac des Iles ores, are described.The paper describes the approach used in circuit optimisation, and how metallurgical and operational optimisation raised palladium recoveries by more than 6% in six months, by tuning the circuit to recover some of the ultra-fine PGM mineralisation.BACKGROUNDThe Lac des Iles mine, owned and operated by North American Palladium Limited, is located about 115 kilometres north of Thunder Bay, Ontario. The mine originally opened in December 1993, and prior to 2001 included a mill capable of handling 2,400 tonnes per day of ore delivered from the nearby Roby pit.Following an intensive exploration programme conducted in 1999, and a detailed feasibility study, conducted in 2000, North American Palladium initiated a mine expansion project, the objective being to expand milling throughput from 2,400 tonnes per day to 15,000 tonnes per day. This required construction of an entirely new mill, which was commissioned in May 2001."

Jan 1, 2003

By Daniel Hodouin, Claude Bazin, René del Villar

"A traditional linkage has long been established at Laval University's Department of Mining & Metallurgy between the Mineral Process (MP) and the Mining Exploitation (Min) on one hand, and between the Extractive Metallurgy (EM) and the Materials Engineering (Mat) on the other. This academic separation of Mineral Processing from Extractive Metallurgy at the educational level has become increasingly at odds with today's industrial practice in which both disciplines are not only complementary but also often intertwined. For instance, in gold ore processing, comminution, flotation, and gravity separation units are interfaced with atmospheric or pressure leaching modules and with carbon adsorption and electrowinning units. The new copper plants in South America combine comminution and flotation circuits with heap leaching, solvent extraction and electrowinning processes.In order to reflect this new industrial reality and to harmonise the options offered in both its engineering programs, the Department of Mining and Metallurgy of Laval University has introduced major changes in its curriculum in 1996. These changes reflect also the recognition that the somewhat secondary status given so far to Mineral Processing and to Extractive Metallurgy within their ""mother"" programs, Mining/Mineral Engineering and Materials metallurgical Engineering respectively, was in sharp contrast with their actual significance for the Canadian economy. Leading industrial voices have raised similar concerns and the Canadian Engineering Accreditation Board has also addressed this problem in its latest program evaluation.The changes implemented at Laval aimed at a) better representing MP and EM within the two undergraduate programs; b) training top-level versatile and multidisciplinary engineers, fluent in all aspects of MP and EM, irrespectively of which of the two ((mother)) programs they had chosen and capable of meeting today's industrial requirements; c) training students in process analysis, optimisation and automatic control using state-of-the-art software, and d) taking into account the co-operative nature of both undergraduate programs.Results are very encouraging in terms of student enrolment and industrial response. However, some concern is expressed on the sustainability of the renewed curriculum considering the drastic budget restrictions in effect at Laval as in most other Canadian universities."

Jan 1, 1999

By Dave Bulled, Jim Thompson, Tim Leriche, Mark Blake, Troy Wilkie

"A commitment to a core testing, plant modeling and reconciling technique has shown substantial economic benefits to IOC in terms of accurate production forecasting, smoother operation of the mill, improved expectations of throughput and co-operation across production departments from geology, planning, mining, and processing, to shipping of concentrate to market.This paper describes a successful seven year program of forecasting throughput of the autogenous milling circuit at the Carol Lake concentrator of IOC. Work started with audits of the grinding circuit in 2001 and benchmarking of the data collected from samples of mill feed and plant operation to the CEET mill design and throughput forecasting model.Initially 390 drill core samples were tested for SAG Power Index (SPI) to measure the energy required in milling, and the data distributed using a geostatistical technique across the two operating pits, so that hardness was estimated in each of the 40,000 blocks (or 1500 million tons) of potential ore. In 2004 a forecast of energy requirement, i.e. forecast of throughput for a given power availability at the mill, was produced for each ore block using the CEET model and used for mine planning to smooth plant throughput. The forecast for blocks mined on a monthly basis was reconciled with plant results over the next 2 years and minor changes made to the CEET model. The forecasting exercise was repeated in 2006 and in 2008 with the latest model based on the testing of almost 1300 samples of drill core at closer spacing.INTRODUCTIONThe contracting of sales to clients and the timely supply of products to meet those contracts is a cornerstone of good business practice. Ensuring the correct scheduling of production is a major concern of mining companies where the supply and qualities of the raw material is uncertain and production facilities are not flexible. This is particularly challenging when the product is of high volume and produced far from the customer, such as iron ore.Apart from the metal content of the ore being mined, the greatest impact on production scheduling is the throughput of the comminution section of the extraction plant; most notably when size reduction is achieved by autogenous grinding. The response of the mills to variability in the hardness of the ore can change throughput by as much as 50% from day to day at some plants."

Jan 1, 2009

By G. D. West, J. D. Purdue

"Marked Ball Wear Testing (MBWT) employs identified grinding balls which are placed in an operating mill for a period of time, retrieved from the mill, and then measured to determine the amount of wear experienced. This is an excellent method to evaluate the relative differences in the wear rates of various grinding ball materials and/ or manufacturing process variables simultaneously and under actual production milling conditions. This paper outlines the methods of ball identification, testing and evaluation procedures and discusses the strengths, weaknesses, and proper application of marked Ball Wear Test results. INTRODUCTIONThe consumption of grinding media in the mineral processing industry represents a substantial cost to the comminution process. Grinding media is most often found to be the second highest consumable cost next to energy. To determine the selection of the most cost effective media, one must determine the specific wear mechanisms present in a given grinding application and decide which media system addresses these mechanisms most economically.A MBWT has definite advantages over other methods used to evaluate the relative consumption rates of grinding media. It allows the comparative testing of a large number of different ball types under identical operating conditions in a very short period of time. In addition, production wear rates can be accurately predicted directly from MBWT results. Typical MBWT test periods are in the order of 350 to 700 operating hours for high wear rate application and upwards of 2000 or 3000 hours for low wear rate applications. These times are much less than the 5000 or more hours required to purge a mill of the incumbent ball charge (to convert it to the test ball) and then provide even a minimal test period in which to conduct a full production test, for just one type of ball. Under production test conditions the evaluation of competitive product or the development of improved grinding balls is necessarily slow."

Jan 1, 1991

By Barrie Robb

Outline 1. Mackenzie Aboriginal Corporation (MAC) 2. ACR background 3. ?Learning from Experience? project - What - Why - lessons 3. How Industry could contribute to sustainable Aboriginal communities 4. Concluding words What is the Mackenzie Aboriginal Corporation (MAC)? ? Aboriginal owned ? Established construction capabilities ? Commitment to development of northern resources ? Partners have extensive experience

May 1, 2008

A key point in the manufacture of cemented backfill is the dewatering and settlement of the total tailings product. A new technology characterized by rapid non-mechanical settlement of total tailings has been developed based on a large number of laboratory and field tests, where dynamic settlement and continual slurry preparation of total tailings in a vertical sand silo are realized by the addition of an effective flocculating agent named NPA. It has been shown that the sedimentation velocity of the interface between total tailings and water after NPA was added is 10 to 20 times higher than that without any flocculating agent, that the mass fraction of sand slurry deposited at the bottom of the vertical sand silo reaches 70%, and that the solid particle content in effluent waste water meets national water quality standards. The simple devices used to add flocculants have little deleterious effects on the current preparation tank and have been tested in an industrial environment. The processing cost of total tailings by the new technology is only 10% to 20% of that required for mechanical settlement.

May 1, 2007

By R. S. Fukuhara, M. J. Allan

"Highmont, a wholly owned subsidiary of Teck Corporation, operates a 25,000 ton/day mine and concentrator located in the Highland Valley of British Columbia. Construction of the plant commenced in the spring of 1979, and production from one grinding line began in late December 1980. The second grinding line began production in March 1980.The ore body consists of two main zones, the east and west pits, containing 134 million tons of ore, averaging 0.26% Cu and 0.27% Mo. Mineralization consists mainly of chalcopyrite (2/3), bornite (1/3), and molybdenite.The concentrator design incorporates an A-B-C grinding circuit (auto mill ball mill - crusher), followed by bulk flotation, copper-moly separation and leaching for moly concentrates. The two grinding and bulk flotation circuits are parallel and independent. Concentrate storage is provided between bulk flotation and copper¬moly separation and also ahead of molybdenite leaching. The plant design has been previously described in some detail. (""THE HIGHMONT CONCENTRATOR"" by C. V. Sibbald, CIMM Bulletin, March 1981).This paper will outline some of the problems associated with the construction, startup and early operation phases of the concentrator. The objective is to help others avoid some of the potential pitfalls by outlining those areas where problems occurred, or where things went well. Criticism of design or equipment is not intended."

Jan 1, 1982

By K. Gie Tan, Frank Wright

"Misty Mountain Gold Limited (MGL - TSE VSE, MGLCF - NASDAQ) of Vancouver, owns the Harmony Gold Project located in the Queen Charlotte Islands of British Columbia. The deposit contains a mineable reserve of 2.3 million ounces of gold, at a 1.2 g/t cut-off and an average grade of 2.1 1 g/t Au.Discovered in 1970 and frequently investigated by previous owners, full-scale production has not yet occurred because of the complex metallurgy of the deposit. Recent process studies that were completed in six months at Process Research Associates Ltd. (PRA) of Vancouver resulted in significant improvements to the project viability. The work involved detailed mineral processing studies aimed at achieving a marketable concentrate. An option for bio-oxidation and cyanidation to allow on-site dor6 production was also investigated.The main findings at PRA followed the front-end recovery of finely divided free gold (Au) by gravity concentration. Approximately 20% of Au reported to less than 0.2% of the mass, resulting in a grade exceeding 500g/t Au. The resulting gravity tailing provided a uniform feed for flotation evaluation. The optimization of this step allowed for a reasonable primary grind size of 80% passing (&) 50pm. Efficient slime’s rejection was made possible by flotation at a reduced pulp density, and pre-oxidized sulphides were reactivated with Na,S. The regrinding of the bulk flotation concentrate followed by up to five stages of cleaning resulted in a combined gravity + flotation product of 50g/t Au with 82% recovery in less than 4% of the feed mass.Further studies indicated that the flotation concentrate was amenable also to tank bio-oxidation. At 65% sulphide oxidation the gold recovery improved from less than 70% to 90% by cyanide extraction using CIL (carbon in leach). This compares to less than 45% gold recovery from whole-ore cyanidation in several previous studies. Heap leaching may also be considered for lower grade material. PRA’s methodical approach and consistent results dispelled the uncertainty about predicting the material behavior for the Harmony Property."

Jan 1, 2000

By Mario E. Rossi

The full economic evaluation of a mining project requires a block model that provides an estimate of the tons and grades of available resources. The model must be representative of the mineralization to be found at the time of mining for specified extraction periods and within acceptable error margins. In an operating mine, there may be a reasonable understanding and estimates of actual dilution and ore loss. This paper discusses the issue from the perspective of a project at a feasibility or preproduction level of development. Three types of dilution are discussed. Internal dilution (or change of support) is function of the spatial distribution of the mineralization and its relation to the operation?s selectivity. Geologic contact dilution is the unavoidable mixture at contacts or boundaries of material with different geologic characteristics, grades, or metallurgical performance. Operational planned and unplanned dilution should also be considered, sometimes incorporated by factoring the resource model, but more accurately by mimicking the grade control process. The resource estimation process always carries uncertainty, which is sometimes significant, and usually caused by several factors. These include quantity and quality of drill hole information; quantity and quality of geologic data; grade estimation methodology; dilution and mining recovery factors applied; etc. A key decision is to whether estimate as accurately as possible the in-situ geologic resource or to estimate the tons and grade of the material to be fed to the processing plant. The geologic modeling and grade estimation methods used are conditioned by this decision.

May 1, 2009

By D. A. Cormode

"INTRODUCTIONPine Point Mines, operated by Cominco Ltd., is located approximately 55 miles east of Hay River, N.W.T. by the southern shore of Great Slave Lake.The milling operation commenced in the fall of 1965 at a design capacity of 5,000 tpd. An addition which came on stream late in 1968 raised the nominal capacity to 8,000 tpd. Currently the milling rate is 11,000 tpd.The lead and zinc sulphides occur in dolomite host rock. Typical feed grades at present are 2% lead, 5.5% zinc and 5 % iron. When dolomite is present even in relatively minor amounts in the zinc concentrate, it presents serious treatment problems and causes inefficient operation of electrolytic zinc refineries.By 1972, it had become apparent that magnesium rejection in the form of dolomite was deteriorating because of increased plant throughput of less amenable ore. This paper will briefly outline the Pine Point zinc flotation circuit and will discuss the two phase program for reducing the magnesium level in the zinc concentrate. The program included changes and alterations to the flotation circuit and the construction of an acid leaching plant."

Jan 1, 1977

By R. W. Lawrence

"In the past year, BioteQ Environmental Technologies Inc. have initiated design and construction of new plants to add to an existing list of plants that utilize the BioSulphide® and ChemSulphide™ process technologies for metal recovery and water treatment. In these plants, low cost biogenic sulfide or, in some cases, chemical sulfide reagent is used to selectively remove metals from contaminated water. The process produces high grade, marketable, metal sulfide products even from low grade feed solutions. The revenues generated from the sale of products can allow for water treatment at a profit in some cases, offset treatment costs in others, and generally reduce sludge disposal and management costs. The effluents produced from the process can meet stringent environmental standards. Current plants in operation and under construction range in sulphide demand from 50 kg/day to 3.7 tonnes/day, with the feasibility of larger plants with sulfide demands ranging from 6 to 43 tonnes/day under review.Biogenic sulfide reagent can also be considered for other applications in hydrometallurgy and mineral processing. Uses under consideration by a number of mining companies include: (1) replacement of sodium hydrosulphide in the SART process for cyanide regeneration and copper recovery in the processing of gold-copper ores, and (2) replacement of sodium hydrosulphide for use in the separation of copper and molybdenum in flotation. Biogenic sulphide, produced on demand at site, offers significant cost savings and provides the additional benefit of improved safety due to the elimination of the transportation, handling and storage required for chemical sulphide reagents.This paper reviews the applications of the BioSulphide® and ChemSulphide™ technologies for water treatment and metal recovery, and introduces projects where biogenic sulfide can be applied in hydrometallurgy and mineral processing."

Jan 1, 2007

By M. H. Attia

The concept of sustainable development has been evolved into a working framework for sustainable manufacturing, in which the environmental requirements are introduced into product development at the design stage. This keynote paper is discussing a number of issues pertaining to the impact of manufacturing on the environment. The conflicting requirements of sustainable development, sustainable manufacturing (SM) and economical growth are presented in the light of successful case studies that were able to convert conflicts into opportunities. Integration of SM into the product life cycle is also presented. A number of concepts that are related to Ecoefficiency, e.g., inverse manufacturing, demanufacturing and re-manufacturing are also discussed. The paper underlines the fact that the positive impact of this new philosophy is equally applicable and beneficial to both; developed and developing countries. The paper concludes with an overview of Global trends in environmentally benign manufacturing (EBM); e.g., product-take back and emerging material and processing technologies. The state-of-the-art approach to Life Cycle Impact Assessment and integration of design for the environment DfE principles are demonstrated through some case study.

Jan 1, 2006

By Mike Sapiro

"Heath Steele Mines is a base metal producer situated near Newcastle, N.B. presently treating 3500 TPD of complex Cu-Pb-Zn ore. The ore consists of massive fine grained sulfides averaging I. 1% Cu, 1.6% Pb and 4.5% Zn.The original mill started in 1956 at 750 TPD and was successively expanded through 1500 to 3000 TPD in 1969. In 1972 an expansion to 4000 TPD was initiated. It was planned to obtain the maximum benefit from equipment and manpower by adding some process equipment, instrumentation, an on stream analyser, and a process control system. The benefits from this approach could be greater than normally expected, because of the complex metallurgy of this ore.IntroductionThe crushing plant is of conventional design with two 5 ½ ft, Symons cone crushers with the crushed ore screened to -7/8 inch on a 61 x 16 1 Al I is Chalmers vibrating screen and stored in four 1000 Ion bins. There are two para I lei grinding circuits, each one consisting of the following: one Rod Mill in open circuit, one Ball Mill in closed circuit with two 20"" Krebs cyclones, and one Ball Mill in closed circuit with three 15"" Krebs cyclones, Al I the Mills are 9' x 121 Al I is Chalmers Mills. The secondary cyclone overflow from each grinding circuit is thickened and combined to form flotation feed. The final product is 65% - 400 Mesh. Two regrind mills have been installed as part of the expansion."

Jan 1, 1977

By Norman O. Lotter, André R. Laplante

"The pursuit of concentrator surveying for purposes of metal accounting or process optimization has not yet connected with the well-published realm of geostatistics. The reality of lognormality in time has seldom been discussed. One publication by Krige, 1962, examined such effects for a gold concentrator in South Africa, towards an information system that would provide feedback to the mining and surveying teams on grade control of ore mined.During present studies which are designing and testing a new survey model, called statistical benchmark surveying, it was found that the distributions of feed, concentrate and tailings bear significant residual signs of the parent lognormality in space. The multiple hosting of paymetals in different mineral species complicates the understanding of these distributions. These features have to be recognized and treated in order to perform appropriate quality control on the diagnostic sampling performed in the pursuit of statistical benchmark surveying.It is shown in this paper that the above two features can actually be used to advantage in the diagnosis of continuous periods of operations data ahead of such surveying, including the estimation of recoverable paymetals in flotation tailings from a graphical method.INTRODUCTIONAssessment of Concentrator PerformanceMilling and flotation, sometimes accompanied by gravity separation, are well-established unit processes, which have traditionally been used to treat ore that has been mined. This is because these processes liberate, then separate, the valuable minerals, which contain paymetals, from host gangue. This is often done by a combination of crushing and grinding processes, or autogenous grinding, to liberate the paymetal minerals, followed by gravity separation and/or flotation, to separate these valuable minerals into a concentrate, or several concentrates. These concentrate(s) have a lower bulk than the parent ore from which they are derived. Further, they contain a high percentage of the valuable minerals. Accordingly, they are more economically treated in subsequent beneficiation processes than the ore from which they were produced."

Jan 1, 2005

By H. Ewaschuk

"INTRODUCTIONRio Algom's involvement with the Enviro-Clear thickener began in May 1975, when tests on a laboratory waif were carried out by our Research and Development group. Commencing in June, further tests were carried out using a 3 foot diameter pilot unit. By December, a 30 foot full-scale thickener had been installed. In the near future, 3 more Enviro-Clear thickeners will be commissioned. With in the space of a year, almost $2.5 million had been committed to liquid/ solid separation facilities using the Enviro-Clear thickener. This paper briefly traces the extent and development of this commitment.BRIEF HISTORY OF QUIRKEQuirke Mine started operating in September 1956 at a rated capacity of 3,000 TOD. Because of market conditions, Quirke was shut down in December 1960. The facilities were re-opened at an increased capacity of 4,000 TPD in July 1968, by which time the demand for uranium had returned. Also, a second shaft was sunk, and by 1970, all of the ore treated in the concentrator was coming from the new Quirke II mine. The Quirke I stopes were allowed to fill with natural seepage. As well, acidic barren solution from the concentrator was pumped underground.With increasing demand for uranium, the capacity of Quirke will be further expanded to 7,000 TPD by 1978. Studies of how this expansion could best he carried out led to the consideration of a fairly new piece of equipment, the Enviro-Clear thickener, for certain operations in the concentrator. These operations are as follows:"

Jan 1, 1977

By J. Lee, R. G. Rosehart

"The basic problem of arsenic contamination from mine water is discussed. Effective methods of removal involving chemical precipitation, activated carbon adsorption, ion exchange and reverse osmosis are discussed. As well as an economic analysis, detail is also paid to other ions in solution which are removed simultaneously.INTRODUCTIONThe object of this paper is to review arsenic and its removal from gold extraction plant effluents. The first method considered is chemical precipitation. A second method is sorption processes, such as ion exchange resins and activated carbon adsorption. A third method is the possible application of reverse osmosis for the treatment of mine waste waters containing arsenic.Arsenic pollution in the gold mining communities of Canada and Ghana have been extensively studies (l, 2). Lynch(3) Shabunin, Gutman and Kogan( 4), Hollo, Troth, Vennes and Illinigi (5) and Hau(6) have reported their removal methods of arsenic by chemical precipitation, ion exchange and biological methods. Their conclusions were that the precipitation with Fe2+ and Fe3+ ions was most effective.Scope of the ProblemInitial aspects of this research program involved a detailed analysis of the operation of a gold extraction plant located in Canada. The name and location of the mine is proprietary information. Figure 1 gives a basic process schematic with the main tailing streams identified.Table 1 gives information as to the various mine streams and their physical and chemical composition. In this study, primary attention is paid to the removal of dissolved arsenic from waste waters. Solids from this type of operation can always be back-filled. As could be anticipated, the dissolved As content of the primary flotation tailing stream is very low. The dissolved As level in the secondary processing stream and the roasting quench water is quite high. The reason being that at this stage of the process, the arsenic has been freed from the arsenopyrite forms."

Jan 1, 1972

By Stephen L. Chryssoulis

"""Preg-robbing"" of gold by carbonaceous matter during the cyanidation of certain types of carbonaceous gold ores is well documented. Recent studies established that ""preg-robbing"" of gold is not limited to carbonaceous matter. Gold sorbed on the surface of pyrite grains was detected and quantified by TOF-LIMS (Time of Flight Laser Ionization Mass Spectrometry). Crystallites of pyrite from a number of ores from different geological environments have been shown to have gold on their surface apparently sorbed from the ore forming solutions. Surface gold accounts for significant fractions of the gold head assay. Preg-robbing of gold by pyrite from pregnant cyanide solutions was also documented, and accounts for significant losses to tailings. Preventative measures are discussed.1.0 IntroductionThe detection and subsequent quantification of gold sorbed on the surface of pyrite particulates came about during routine determinations of the deportment of gold employing the comprehensive mineralogical approach (Chryssoulis and Cabri, 1990). In some pyritic gold ores it was discovered that the sum of the various forms in which gold ""conventionally"" occurs, was short of the gold assay. The mineralogical procedure used involves the independent determination of each fraction of gold, in other words there is no form of gold which is calculated ""by difference"". The systematic shortfall after having added the forms of gold listed in Table 1 led to the inquiry for the 'missing' gold and its discovery on the surface of pyrite grains, such as crystal facets and fractured surfaces.Preg-robbing of gold by pyrite from pregnant solutions was first described by Lloyd. In his studies, preg-robbing was measured by changes in the solutions/solids gold assays. This paper describes the first application of a direct measurement method for surface gold on pyrite particles from untreated and processed samples, its impact on gold deportment and processing. The advantage of the direct measurement lies in the absence of interference from other forms of gold, leading to more accurate and precise determinations of this unconventional form of gold."

Jan 1, 1997

By A. Uribe-Salas, J. A. Finch, B. J. Huls

Froth depth or interface level is an important control variable in column flotation which can influence both grade and recovery. A common method of locating the level is based on sensing the hydrostatic pressure at one or more points along the column. The level position is then calculated from these pressure readings using an equation which includes the bulk density in the froth and bubbling zones. The precision with which the level is detected depends on how well these density values represent both zones. The calculation of these bulk densities from theoretical considerations is not possible and, therefore, the practice is to estimate them by calibration. Unfortunately, the calibration parameters often do not report the level with an acceptable accuracy. A portable conductivity probe has been developed to detect the position of the interface from conductance measurements across the interface. The location of the interface corresponds to the position where a large change in conductance is observed, which is primarily a consequence of the difference in gas holdup between the bubbling and froth zones. This probe can be used to detect the position of the interface to an accuracy of± 5 cm. The probe can be used while the column is in operation, which allows the on-line calibration of the level detection system. Results obtained in its application in a pilot-scale column (0.91 min diameter) are described.

Jan 1, 1989

By Dayang Datu Khalil, Charle Amoah, Fred Kock

Abosso Goldfields Limited has been optimizing the comminution circuit at the Damang Mine Operation for the treatment of 100% primary ore. The optimization process started at a base rate of 343 tph when treating primary crushed primary ore, and was increased to above 600 tph with partially crushed primary ore. Abosso Goldfields engaged Orway Mineral Consultants (OMC) to assist with the optimization process in 2009 and the two companies have been working together since, to further refine the process. Continuous improvement was achieved through crushing circuit modifications, changes in operating processes and grinding control system utilization. This paper discusses the improvements developed for the increase in milling capacity and improvements in final product size.

Jan 1, 2012