Search Documents

By D J. Williams

Tailings management is typically constrained by many factors that are taken as given. These include the tailings production rate that must be accommodated, the desire to deliver the tailings cheaply and easily as a slurry using centrifugal pumps, and a tailings footprint limited by the desire to minimise capital costs leading to a rapid tailings rate of rise and a low settled density. Other constraints include wall raises being delayed due to limited capital, inadequate tailings water and rainfall run-off management, and the net present value (NPV) approach to capital expenditure that puts off expenditure at the expense of performance. All of these constraints result in the tailings occupying much more volume than is necessary, being difficult to rehabilitate, and not being capable of supporting a beneficial post-mining land use or function. Ultimately, such constrained tailings storage facilities will assume very large dimensions, but each will typically be developed as a series of smaller storages that are filled rapidly and added to progressively. The optimal stage to efficiently recover process water is in the process plant, but this is limited by the desire to use centrifugal pumps rather than the more costly positive displacement pumps, which also require greater management of tailings deposition. Process water can also be recovered from the tailings storage facility (TSF) decant. Tailings water that is not recovered from the plant or the decant will be lost to entrainment within the tailings, seepage to the foundation or through the wall, or evaporation. However, tailings water is not always suitable for reuse in the plant, particularly when it becomes contaminated by the processing, and it may simply be stored on the TSF. This will exacerbate the seepage of contaminated water to the environment, and will limit the densification of the tailings that would otherwise occur due to desiccation of the tailings on exposure. If a larger tailings footprint were developed early, cycling of tailings deposition in thin lifts between a number of cells could occur, maintaining the dormant cells dry to enhance desiccation and densification, and ultimate rehabilitation. The end result would be a much reduced stored volume of tailings, the potential for upstream raising, and ease of rehabilitation to a high level. The higher initial capital cost would be overtaken by reduced ongoing capital, operating and closure costs.CITATION:Williams, D J, ?2014. An alternative whole-of-life approach to tailings management, in Proceedings Life-of-Mine 2014 , pp 285–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

By J Jeffrey, G W. Wilson, L Gilbert, C

Prior to the commencement of mining, the acid rock drainage (ARD) potential of the waste rock to be produced by an open cut mining operation is assessed by a variety of techniques carried out on drill-hole samples. These include, among others, acid base accounting (ABA), net acid generation (NAG) testing, and kinetic testing. Based on the results obtained, a strategy for the identification, separation and selective placement of waste rock having different potentials to form ARD is developed. During the course of mining, the waste rock classification scheme will be re-assessed periodically to confirm that it is appropriate. This re-evaluation may result in a change in classification scheme, and waste rock dump samples may be obtained for ARD assay purposes to confirm the appropriateness of the revised scheme. The paper describes the evolution over time of the scheme used to classify waste rock at a major open pit gold operation in New South Wales, Australia, including the development of a hydrological model. To confirm the appropriateness of the revised scheme, ARD assay testing was carried out on drill-hole samples collected from dumps having different ARD potential designations, including Non-Acid Forming (NAF), Potentially Acid Forming (PAF), and Low Grade Ore stockpiles. The results of the ARD assay testing and water quality monitoring confirmed the appropriateness of the ARD potential designations and the revised classification scheme, which has been adopted.

Jan 1, 2003

The green field discovery of a two million ounce high-grade refractory gold ore deposit in the Indonesian Province of Sulawesi Utara, led Newmont to utilise its proven technical expertise in dry grinding and whole ore roasting to develop a 2000 tonne per day, 160 000 ounce per year operation in this remote and picturesque location.Located at an elevation of 250 in above sea level and ten kilometres to a deep water natural harbour, the hard rock open pit mine, process plant and infrastructure facilities were built to budget at a capital cost of US$132 million. The plant was commissioned with oxide ore, with the first gold poured in March 1996 and with refractory ore in January 1997. The operation rapidly met its production targets because of extensive forward planning and training programs developed for the local workforce. The presence of steep topography, fertile coastal plains, high rainfall, high seismicity of this location led to the decision to dispose of neutralised tailings in deep water off the coast instead of impounding tailings in a dam. This paper describes the development of the project and the challenges in developing a gold operation in a remote location which lacked infrastructure, the steps taken to ensure a smooth commissioning, and the selection of the workforce to operate a technically sophisticated facility.

Jan 1, 1997

By P Salmon, M Kennedy

Sun Metals Corporation Pty Ltd (SMC), a wholly owned subsidiary of Korea Zinc Co Ltd (KZC) is a company formed to develop, construct and operate a zinc refinery, 11 km south of Townsville in North Queensland. The project opportunity exists because of on-going consumption growth for refined zinc metal, technological, environmental and economic obsolescence of existing zinc processing plants, and a prolonged ædroughtÆ of new zinc processing capacity under construction. The Project will utilise proven technology developed by KZC at the Onsan refinery in Korea. The Townsville Refinery has been designed to be the most environmentally-friendly zinc refinery in the world, and in particular to resolve the issue of secure, long term treatment of the ironbearing content of the zinc raw materials.

Jan 1, 1998

By S M. Denn

The Cawse nickel-cobalt operation is situated 50 km NW of Kalgoorlie in Western Australia, at latitude30o22'30'' south and longitude 121o08'30'' east on the Kalgoorlie 1:250 000 geological map sheet (SH 51-9) (see Figure 1). The project is owned and operated by Centaur Nickel Pty Ltd (CTR) and was the first in Australia to commercially produce nickel metal and cobalt sulphide through pressure acid leach (PAL) technology. Cawse has a total resource base (all categories of resources + reserves) of 213 million tonnes Mt at 0.7 per cent Ni and 0.04 per cent Co, comprising 127 Mt at Cawse Central which is 100 per cent owned by CTR and 86 Mt at Cawse Extended where CTR has a 80 per cent equity. Cawse Extended is located immediately to the northwest of the Cawse Central leases. All current reserves (proved and probable) of 30 Mt at 1.0 per cent nickel are contained within Cawse Central. In addition the Siberia project area 20 kilometres to the NW has a resource of 63 Mt at 0.7 per cent Ni. Cawse is a dry laterite deposit, with nickel and cobalt hosted by iron and manganese oxides. Cawse Central mineralisation extends over a ten kilometre strike length, with three pits currently being mined. The Bunyip pit has the premier nickel and cobalt grades within Cawse Central. There are seven dominant lithology types forming mappable units within current pit exposures. Four of these units are host to nickel and cobalt mineralisation. Ore types are defined as Upgrade, Grind and Non-upgrade, depending on their physical characteristics with respect to the treatment route. Mining commenced in February 1998. To the end of calender 1999 the operation has produced 2100 tonnes nickel plate and 470 tonnes of cobalt as a cobalt sulphide product. Future production will target 9000 tonnes per annum Ni metal and up to 2000 tonnes per annum Co, based on processing 500 000 tonnes of ore per annum.

Jan 1, 2000

By White L. R, Boger D. V

The paper describes the surface chemistry and particle physics that control the fundamental flow properties (Theology) of mineral particle slurries. We further address, through a series of case studies, the design data that emerges from experimental studies of the flow properties of complex, high volume fraction mineral slurries. The case studies are drawn from mineral oxide concentrate processes, tailings dewatering operations and from filter cake production and management. The paper emphasises the essential links between design of process slurry handling systems and the control of the flow of such slurries by control of the pulp chemistry.

Jan 1, 1992

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

Valuers of mineral properties should be aware that accountants are a major user of their opinions of value. Reliance by accountants can range from obtaining comfort that book values in balance sheets are not overstated to establishing values by which to assess the fairness of a takeover offer. Accountants using mineral property valuations clearly can't be expected to have the same level of expertise as the valuer and ""second guess"" the valuation. But they do have an obligation, under the ASC guidelines and their own professional standards, to'check the logic and reasonableness of the valuation before being able to rely on it. This means reviewing the valuation report for general sensibility, discussing the methodologies and assumptions with the valuer and being satisfied as to his competence and independence. This paper outlines how accountants use mineral property valuations, the level of scrutiny applied to such valuations and the problems commonly encountered in practice by accountants seeking to rely on them. The paper also explains how values of-mineral properties are established in company balance sheets and why these often differ, quite validly, from fair market values.

Jan 1, 1994

By A Datar, D Mulligan

The extractive phase of broad-scale mining can have major impacts on landscapes and associated ecosystems. Post-mining ecological rehabilitation typically starts with reconstructing topography. A fairly common industry practice has been to use landform elements such as plateaus, terraces, and gentle slopes for stabilisation purposes. However, this approach can lead to the generation of fairly uniform landforms that do not necessarily reflect natural ecosystems. Previous research in undisturbed and agricultural landscapes shows that ecological attributes and diversity in microclimates is positively correlated with landform heterogeneity. An objective of this study was to investigate if those findings are still valid in post-mining rehabilitating landscapes on North Stradbroke Island, Queensland, Australia. We investigated the relationship between landform heterogeneity and status of ecological recovery. The landform heterogeneity is measured through variance in three landform characteristics (relief, slope, aspect) using remote-sensing data and the status of ecological recovery is represented by ecological indicators measured through field surveys. The results indicate strong correlations between landform heterogeneity indices and native vegetation species richness with sensitivity to the spatial scale of investigation. It is recognised that climate, substrate and rehabilitation practices act as primary drivers of rehabilitation success. However, the results indicate that, in some examples, landform heterogeneity (heterogeneity in relief and slope angles) contributes up to 30 to 50?per?cent of the variance in native vegetation species richness. While the primary drivers of ecological recovery are difficult to control over extensive areas and extended time periods, landform heterogeneity provides a tool to indirectly control the micro-environmental parameters to improve ecological recovery. Reducing the uncertainties in the choice of ecological and landform indices and the degree of landform heterogeneity suitable for particular rehabilitating landscapes would be site specific. The introduction of desired landform heterogeneity may provide a very effective tool for significant improvement in ecological rehabilitation across broad-scale post-mine landscapes, an outcome of benefit to industry, government and local communities.CITATION:Datar, A and Mulligan,?D,?2014. Do we need to change the way we set up the stage?, in Proceedings Life-of-Mine 2014 , pp 29–46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 16, 2014

We all live in professional silos û comfort zones, where we talk to like-minded people with the same training, experience and view of the world. We note in passing the existence of other disciplines, but they are tolerated rather than embraced. To the geologist, the metallurgist is a mad scientist conjuring gold out of some foul solution about which the less said the better. To the metallurgist, the geologist is a bearded, self-appointed sage who guesses what is under our feet by sniffing the air, and drives a Land Rover badly. As to the view of mining engineers held by both geologists and metallurgists, this is best left to the imagination. And of course we are all confused by the term æmetallurgistÆ. I am called a metallurgist though my skills are in mineral processing not metal processing, but I canÆt be called a mineralogist because that definition is already taken. *Please note that this is available as an extended abstract only*

Jan 1, 2005

By R Ulusay

Rock mechanics involves characterizing the mechanical properties and behaviour of rock material and the natural discontinuities of the rock mass, while rock engineering is concerned with specific engineering circumstances, for example, how much load will the rock support and whether reinforcement is necessary. Rock engineering models developed depend considerably on the input data such as boundary conditions, the properties of rock material and rock mass. Correct evaluation of these properties frequently requires laboratory and in-situ tests, supplemented with a high degree of experience and judgment. Accordingly, since 1974, the ISRM Commission on Testing Methods has spent considerable effort in developing a succession of the ISRM Suggested Methods (SMs) for different aspects of rock mechanics and rock engineering with the contribution of a number of working groups and cooperation of some other ISRM Commissions. This paper emphasizes the need and importance of standardization of rock testing methods within the context of the ISRM SMs, gives a guideline for developing ISRM SMs and finally discusses on some implementation and contractual issues associated with rock testing and experienced in practice, and briefly introduces main future trends in rock characterization, testing and monitoring. This is an extended abstract only. CITATION:Ulusay, R, 2018. Standardisation on rock characterisation, testing and monitoring with emphasis on ISRM suggested methods, practical issues and difficulties, and future trends, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 17–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By M Cooksey, Z Zhu, N Langrené, W Chen, T Tarnopolskaya

"Dynamic decision-making can significantly increase the value of mining projects and deliver better sustainability outcomes under conditions of uncertainty. Despite its benefits, dynamic decision-making is rarely used by the mining industry, possibly because of the complexity of the algorithms used to make sequential decisions under uncertainty and difficulties in visualising the optimal strategies. To achieve better outcomes in practice, decision-makers in industry would benefit from a tool that would help them to understand and implement the results of the analysis.CSIRO is developing innovative dynamic decision support tools that include an intuitive graphical display of the boundaries between the regions of different optimal decisions, which would significantly assist optimal sequential decision-making under uncertainty. The dynamic decision support tool is based on novel stochastic optimal control methodologies that can be used to optimise decisions in situations with multiple uncertain variables and decisions (Tarnopolskaya, Chen and Bao, 2015; Chen et al, 2015; Langrené et al, 2015). The types of market uncertainties that can be considered include commodity prices, interest rates and exchange rate, while the key orebody uncertainties include the reserves, boundaries between ore types and even geometallurgical parameters.The dynamic decision support tools have a number of benefits and can be used to:construct optimal operational strategies and to optimally manage resources projectsgain insight into optimal strategies under different market conditions and project settings compare expected project values under different project settings and to select the setting that provides best sustainability outcomes.This extended abstract demonstrates the use and benefits of the dynamic decision support tools using a synthetic case study of a gold mine.CITATION:Chen, W, Langrené, N, Tarnopolskaya, T, Zhu, Z and Cooksey, M, 2016. Dynamic decisions under uncertainty – a case study on a gold mine, in Proceedings Life-of-Mine 2016 Conference, pp 20–23 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By M J. Cole, J Zhou, D J. Borrow, S M. Iveson, K P. Galvin, J L. Sutherland

New technologies can easily take around ten years to commercialise. Strong research support is needed in parallel with the process of innovation and commercialisation, in building a deeper understanding of the underpinning physicochemical and hydrodynamic forces that deliver the separations, in achieving improvements, in the deployment of a new technology, and in expanding the innovation platform to create new IP. External investment beyond the research, derived from the genuine value proposition of transformational change, funds the pathway for traversing the so-called Valley of Death.

Aug 24, 2022

By D Craw, C Smith, C Martin

The Wangaloa coal mine closed in 1989, and an attempt to grow Pinus radiata on quartz-rich overburden dumps was not successful. The site is currently being rehabilitated with re-profiling and native plant establishment. Plants are being established in a range of substrates that consist of variably disaggregated Tertiary coal measure sediments derived from the mine sequence. This material has low organic matter content (typically <10 %), originating from coal fines or carbonaceous sediment. Substrate samples were collected during December 2003 from a range of sites varying in age, slope, and parent material. Nutrient analysis includes nitrate, ammonia, total N, total P, available P and readily exchangeable base cations. Total nitrogen and phosphorus are low on areas of recently disturbed, quartz-rich overburden, with total N =1200 mg/kg, and total P =200 mg/kg. Background forested areas have total N ranging between 2800 - 3300 mg/kg and total P of 420 - 500 mg/kg. Quartz-rich overburden sites contain available nitrogen levels of less than 6 mg/kg, while background forested areas are generally >20 mg/kg. The soils and water runoff are generally acid, with pH down to three. Water samples have been collected from both ground and surface resources on a monthly basis since December 2003. The main lake on the site had pH of 4.6 in 1999, and this remained relatively unchanged when 850 tonnes of lime were added in 2002. However, the lake pH changed to 6.4 within a one month period in 2004, and has fluctuated since that time.

Jan 1, 2004

Mining is a global industry. The conference is a good example of this, as itÆs jointly organised by professional associations from Canada, Australia and South Africa, and has attracted speakers and delegates from around the world. I commend the organisers for their initiative. I am pleased to be asked to participate in this panel û although I would hasten to add I see myself as perhaps an informed observer rather than an expert. It wonÆt be news to most in this room that AustraliaÆs mining sector is booming. As one of the most productive and diversified mineral regions in the world, this activity is also something that has not escaped the attention of CanadaÆs largest mining companies! This means that I follow what is happening in the industry and more specifically what might be occurring here. Two-way investment between Canada and Australia stood at $9.8 billion in 2005 with Canada as the seventh largest overall investor in Australia with $8.22 billion in investments. The majority of this investment is by Canadian minerals and metals companies. In recognition of the importance of Canadian investment in this sector in Australia, I maintain close contact with our companies. By way of example, in the past two months I spent a week in Western Australia visiting Perth and meeting with companies for example, like Teck Cominco and LionOre as well as seeing various Barrick Gold operations in Kalgoorlie. I attended the opening of AlcanÆs new Asia Pacific Headquarters in Brisbane in August and just two weeks ago was in Cowal, NSW for the opening of BarrickÆs new mine there. Having met with BHP Billiton in Vancouver, IÆm equally aware of active Australian mining interests in Canada. This is not designed to indicate how active I am but rather to demonstrate the dynamism in the mining industry and the diversity of Canadian mining interests in this country and Australian interests in Canada.

Jan 1, 2006

By Rokot M

In a little over three years, Chevron Niugini has built up a team of relatively young, hard working men and women, mostly Papua New Guineans, who spend most of their working days out among people in the Southern Highlands and Gulf Provinces who are directly affected by the Kutubu Petroleum Development Project. These are Land and Community Relations officers, or LACROs. They take on a huge responsibility, not only representing Chevron but also being friend, advisor and negotiator, frequently dispensers of medicines, and agricultural advice and more. When things go well, others get the praise, when things go wrong, LACROs are the martyrs. Just as the geologists who locate the oil, the drillers who find it, the engineers who design the facilities, the construction gangs who build them, the landowners who claim it, and the Government who monitor it, so are the LACROs part of a team.

Jan 1, 1991

Gold mineralisation at Wapolu lies within an exposed arcuate zone at the decollement contact between a basement dome of high grade metamorphics and an overlying ophiolite sequence. This contact was originally a thrust fault which has since become a decollement zone for gravity sliding in association with basement doming. Hydrothermal models for the gold mineralisation postulate an epithermal system in which fluids were channelled up the decollement with boiling of those fluids causing hydrothermal brecciation and subsequent gold deposition. The alteration assemblages, fluid inclusion data and geochemistry indicate that the upper levels of the system are exposed.

Jan 1, 1987

By K Whelan

The Land Access Branch of the Mines Division of the Northern Territory Department of Mines and Energy is responsible for Aboriginal Liaison and cross-cultural matters that affect the Department. In essence, it exists to provide a basis for communication between the Department, industry. Aboriginal organisations and Traditional Owners. The paper outlines the various ways in which this is accomplished including the preparation of detriment submissions for pending land claim hearings, the use of promotional material to support access to Aboriginal Land for NTGS Mapping Programs and field work, and advice/assistance on exploration and mining issues.

Jan 1, 1994

By N Wharmby

In recent years in New Zealand there have been a number of tunnelling and deep directionally drilled pipelines projects that have required access shafts. Often these shafts are in urban environmentswhere vibration and high noise levels are not tolerable. There are a number of methodologies that can be adopted dependent upon the shaft plan area, depth and geology.This paper will describe some different methodologies that can be adopted that use piling methods such as large diameter piles, and secant piles. The paper will use case studies to highlight:· construction methodology,· specific methodology issues and constraints,· lessons learnt, and· recommended specifications.The development of piling technologies in New Zealand has enabled the development of cost effective solutions for the construction of deep shafts in sensitive urban environments.

Mar 8, 2011

Exploration and mining title administration in the Northern Territory has changed dramatically over the last 20 years. These changes have occurred due to legislative amendments, technological developments, and the changing face of the mining industry. The first legislation to control mining in the Northern Territory was the Northern Territory Gold Mining Act (1873) of South Australia. In 1911, control of the Northern Territory was passed from South Australia to the Commonwealth. As a result of the mining boom which followed the discovery of gold in Tennant Creek in 1932, the Commonwealth passed the Mining Ordinance of 1939. This legislation was amended 39 times and stayed in force until July 1982, when the self-governing Northern Territory passed the Mining Act 1980. This Act is still in force and is continuously under review. The first computerised mining titles system, REGIS, was created in 1984/85 and was, to all intents and purposes, just a computerised index. Various modifications ensued, and in 1989 the Titles Database was unveiled. The database has developed to be one of the most sophisticated yet user-friendly mining titles databases in Australia. In excess of 50 companies have access to the database from their own offices. Work continues on its development and fine-tuning. The paper outlines the development of the database since inception.

Jan 1, 1994