Search Documents

The Hunter Fracture Zone can be traced into the Fiji group, and onshore SE Viti Levu in the form of NE-trending morphostructures. NW- trending morphostructures offset the NE elements. Structural mapping of Suva Harbour indicates that the NE elements are grabens bordered by faulted monoclines. Faulting is characterised by block-rotations and dip-slip displacements. The NW morphostructures are faults displaying elements of both dip-slip and strike-slip movement. Structural overprinting suggests that the NW faults represent the youngest phase of deformation, and current seismic activity occurs on this trend. A conceptual, geomechanical model of the deformation invokes toppling and wedge failure at the edge of the Fiji platform, translating material downslope into the Hunter Fracture Zone. The interference pattern produced by the superposition of the NW on the NE structures consists of a series of circular features bearing superficial resemblance to volcanic centres. Known mineral deposits in SE Viti Levu correspond closely to these features. The formation of the circular features postdates mineral genesis, suggesting that the features provide a focus for the enhanced exposure of mineral deposits rather than a source of mineralisation. There is a close association between mineralised exposures and interference patterns in extensional structures in SE Viti Levu, and a correlation between these structures onshore, and the Hunter Fracture Zone cum South New Hebrides Trench offshore. Future mineral exploration in the SW Pacific will benefit by closer consideration of the geologic structure of Pacific islands bordering the extensional regimes of deep oceanic trenches.

Jan 1, 1987

The need to solve the problems associated with spontaneous combustion, system of ventil- ation and methane drainage in gassy coal mines has brought about the development of mining and degassing methods which has made possible up to 80% gas recovery in retreating longwalls. Beneficial results also were obtained mostly in the double or multiple-entry systems, but for single-entry systems and for a seam thickness exceeding 3 m, gas recovery rate is still very low. With some single-heading systems, such as those where a return roadway is not maintained in the goaf behind the face line, a new methane drainage technology is practiced. Attempts were made to extract methane from roof holes drilled from offsets in the ribside of the longwall block. The inclinations and lengths of the boreholes were planned and designed on the basis of the geological and mining condit- ions encountered at the time and every second hole was terminated precisely at the point where the previous hole intersected the immed- iate roof goaf area above the face. There are mathematical relations approp- riate to the design of the above drainage systems to give optimum methane recovery under the given conditions. Some examples of drainage have reached 87% recovery and have attained 94% CH4 purity.

Jan 1, 1982

This paper describes the MillMapper technology developed for condition monitoring of liners and other operational parameters in grinding mills used for mineral comminution, by presenting a case study of its application. MillMapper provides maintenance engineers, operations managers and process and plant metallurgists with quantitative, accurate and reliable condition monitoring data for informed decision making regarding the maintenance and metallurgical aspects of such mills. MillMapper uses calibrated laser scanners for the capture of three-dimensional surface representations inside a mill during a shutdown so as to determine shell, feed and discharge liner thickness at a resolution of several million data points, a procedure that nominally takes five minutes to complete. Once several data sets over time have been collected inside a mill, MillMapper can be used for liner wear, liner wear zone, liner weight, ball charge volume, ball charge weight and intelligent profile tracking over time. Liner tracking in combination with site defined reline and failure criteria and with throughput tonnage data is utilised for change out prediction of each separate liner segment type.

Jan 1, 2008

By Lewis PC, Carr GR, Dean JA, Glen RA

The Lachlan Fold Belt (LFB) is a complex orogenic belt which developed in Early to Mid Palaeozoic time. A number of orogenies and more localised deformational events affected the region. A simplified classification scheme for the diverse gold deposit types is proposed, subdividing primary mineralizing processes into four categories: volcanism (epithermal and volcanogenic deposits), igneous intrusion (subvolcanic/porphyry style, skarn and magmatic deposits), metahydrothermal processes (deposits generated during metamorphism and regional deformation) and hydrothermal-distal processes (deposits generated by poorly understood, generally remote large scale hydrothermal processes). Major gold deposit associations include epithermal and porphyry style deposits in Ordovician-Early Silurian shoshonitic andesite sequences; volcanogenic base metal-gold deposits in Silurian rift or basin felsic sequences; vein deposits in Late Silurian and Early Devonian S and I-type granitoids; deposits in Early Devonian sedimentary rocks of the Cobar Basin probably generated by metahydrothermal processes during basin closure and cleavage formation; deposits associated with serpentinite; and metahydrothermal quartz vein deposits in folded sedimentary rocks.Studies of host rock geochemistry suggest a relationship between magma types, gold enrichment and mineralization particularly in shoshonitic sequences and Early Devonian granitoids of the Boggy Plain Supersuite. Structural studies indicate the importance of thrust type structures and detachment faults in generation and location of gold mineralization. Lead isotope initial ratios help define metallogenic associations and a number of distinctive isotope "signatures" have been established.

Jan 1, 1990

By B Andrew, L Krois

Ground control systems, including ground control management, play an integral role in the effective and efficient extraction of copper ore at the Xstrata Copper û Mount Isa Copper Operations (MICO). Rock mechanics engineers and support technicians at Xstrata Copper have undertaken a wide range of investigations and actions over the past few years. Outcomes from this work have resulted in the evolution of ground control management practices on the site. Specific areas of improvement include the installation of efficient one pass ground control systems, greater application of sprayed concrete for areas requiring rehabilitation and the addition of new improved products, the removal of obsolete and less efficient products used in standard ground control practice. In some areas underground, the most effective methods to manage ground control hazards continue to be a variation on proven methods that have been in use for many years in the MICO. Ground control systems for developing through the basement contact zone are very similar to that developed in the late 1980s. Similarly, ground control systems have gone through repetitive evolution, whereby some systems fall in and out of favour subject to perceived costs. For example the pouring of concrete shuttering around drawpoints in poor ground conditions has recently been re-accepted as an effective means to manage this poor environment û despite having been previously cast aside as too expensive. Ground control management systems continue to evolve towards the goal of creating a workplace that is free of rockfall-related injuries and provide for higher levels of efficient and effective techniques by which ore is extracted from the ground.

Jan 1, 2005

By Chapman G. J

Mining operations require detailed and precise methods and procedures for the optimum selection of ore from waste. A fundamental procedure applied to achieve this selection is accurate sampling. The key parameter to accurate sampling is an understanding of the degree of heterogeneity of the key element contained within a sampling mass. This paper will describe the methods applied for the calculation of the fundamental sampling error and the techniques used to achieve a representative sample in the Fimiston Open Pit, Kalgoorlie.The utilisation of Pierre Gy's sampling theory has optimised the blast hole sample quality and quantity for submission to the assay laboratory. This has resulted in reduced cost and optimised assay reliability in statistical terms. Similarly the analysis of exploration drill holes for resource definition has optimised drilling procedures in terms of the drilling method, sample length and sample quantity.

Jan 1, 1993

By Quast K

A series of laboratory flotation tests were conducted to evaluate the effectiveness of various depressants as arsenic (and zinc) depressants in the lead cleaner stage of the NBHC mill at Broken Hill. The depressants used included potassium cyanide, ferrous sulphate, sodium hypochlorite, potassium ferricyanide and two Cyanamid commerical depressants, Aerodepressants 610 and 633. A standard roughing stage was completed before the addition of the reagents in the cleaning stage. All reagents tested produced significant arsenic depression, with the best results being obtained with the addition of potassium cyanide and sodium hypochlorite. Some of the depressants activated the zinc in the process of arsenic depression. The best result was obtained with the addition of 90 g/t potassium cyanide at a pH of 10 when arsenic recovery was only 1/4 that of the value obtained for the standard test.

Jan 1, 1991

By D Hodder, M Hoskins, A Rofe

Pasminco Century MineÆs slurry pipeline was commissioned in November 1999. It currently transports zinc and lead concentrate slurries in batch form to the Port facility, 304 km away in the Gulf of Carpentaria. The Pipeline and the Port have gone through several stages of continuous improvement to match the successful ramp-up of the concentrator. Improvements in the Pipeline and Port Operations have included: commissioning of the first slurry pipeline that delivers two products in the same pipeline in batch mode; management of batches throughout the pipeline and port system to minimise cross contamination of both concentrates; operation of the slurry pipeline to achieve high availability of the system; operation of the pump station interfaced with preventive maintenance to minimise unplanned shutdowns; continuous monitoring of pressures throughout the single-station, 304 km slurry pipeline; redesign of the Rotary screw feeder; redesign of the Dryer Control System; installation of a larger Induced Draft Fan; optimisation of the dryer internals to achieve a product of narrow size distribution and pellet integrity; redesign of the stockpile ventilation system; and the development of a surface sealant. This paper describes the early commissioning of both the Port and the Pipeline and the continuous learning and Quality Improvement Project initiated at the Port to focus on concentrate quality given the propensity of the fine concentrate to self-heat during storage.

Jan 1, 2003

By Boland J

Prediction of rock cuttability by various excavation machines such as tunnel boring machines, road headers, rippers, picks, roller disc cutters, excavators, etc is of major concern to both civil and mining engineers and rock mechanics. In principle, the design of a rock cutting tool is based on achieving maximum excavation with minimum input energy, minimum applied force, minimum equipment weight and volume and, more importantly, minimum tool wear. When a rock material is indented by the force of a cutting tool and then unloaded several material zones form underneath and around the tool. As the tool moves into the rock the volume of its associated rock cavity (ie volume of displaced rock) expands and depending on the indenter's shape various phenomena may occur. Immediately beneath the tool a small zone in which the stress state is more or less hydrostatic, is formed which is underlain by an inelastic, or damaged, material zone. Both size and shape of this damaged zone control the magnitude of the indentation force and the chip formation mechanism during unloading. The rock is unable to store the whole strain energy induced by the tool and consequently the extra energy is expended either in forming new fracture surfaces and/or in plastic deformation in the damaged zone. Therefore, it is not surprising to see that both perfect-elastic and rigid-plastic constitutive models are not generally suitable for modelling indentation of rocks. In contrast elastoplastic constitutive models are more appropriate as they can include both elastic and plastic deformations (Kral et al, 1993). Elastic solutions for several half-space indentation problems can be found in most text books on elasticity and in particular in Timoshenko and Goodier (1951), Sneddon, (1951), Poulos and Davis (1974) and Johnson (1985a). If a failure criterion, eg the Mohr-Coulomb failure criterion, is applied to delimit elastic solutions for indentation problems, a lower bound limit of the applied indentation force (for a given indentation depth) can be estimated. It may be noted that elastic analyses, without any delimiting failure criteria, normally overestimate the indentation force. Plastic solutions for a few indentation problems may be found in Hill (1950), Johnson, (1985a) and Alehossein et al (1992). When analysing the behaviour of indented rocks the choice of an appropriate constitutive model describing effectively the behaviour of the rock at various stages and phases during indentation is a challenging issue. Several questions need to be answered before starting an effective analysis. The first question is of course: Which one of these is more appropriate for modelling zones underneath and around a cutter, elasticity or plasticity theory, continuum damage mechanics or fracture mechanics, and what is the bridging link between these various theories? Which mode is more dominant in fracturing rock, tensile or shear mode? What governs the mechanism of chip formation? What is the function, shape and the behaviour of the pulverised zone that forms just underneath a cutter? Is the hydrostatic stress state assumption reasonable for this zone? How does the rock change during the absorption and dissipation of the input energy and how does the indentation energy vary with rock type and depth of penetration? How can we model the damaged zone under the indenter? Furthermore does a plastic material form beneath the pulverised zone? When and how do radial and ring cracks form around and under an indenter?

Jan 1, 1995

By K Kinnunen

A strong correlation between the reduction degradation index (RDI) of production sinter and the titanium content of the sinter mix was identified at the Ruukki sintering plant between 2000 and 2004. The titanium distribution in different mineral phases was studied using samples from pot sintering tests. Titanium additions were made using two different materials: rutile and crushed titanium-bearing haematite pellets. While both titanium additions clearly increased the RDI, titanium seemed to favour secondary haematite. The study focused on the effect of titanium in haematite, because haematite is reduced to magnetite in the RDI test. During the haematite-magnetite reduction, reduction degradation was observed. To increase accuracy, the phenomenon was investigated first by sintering and then reducing synthetic minerals under controlled laboratory conditions at the University of Oulu. The effect of titanium oxide in solid solution in magnetite on the magnetite to haematite transformation rate was studied first in order to simulate the final stage of the sintering process. In other experiments, haematite samples doped with 0.5, 2.0 and 5.0 wt per cent titanium oxide were studied using thermogravimetry under a controlled gas atmosphere (CO/CO2/H2/N2). Sintered samples were reduced using the same gas composition as in the RDI test. Polished sections for optical microscopy and SEM-EDS analysis were prepared from both reduced and oxidised samples and unreduced sintered samples. The titanium oxide content of haematite had a clear effect on reduction degradation of the samples. Furthermore, increasing titanium oxide content in solid solution in magnetite radically accelerated the oxidation rate. Similar observations regarding the effects of titanium have been reported earlier, but this was the first time the effect of very small additions of titanium were shown to deteriorate blast furnace burden quality and a reason suggested behind the process.

Jan 1, 2007

Incidental to the progress of a geological survey of the Kalgoorlie goldfield during 1927-28 a number of specimens of telluride minerals were obtained, chiefly with the help of Mr. F. G. Brinsden, general manager of the South Kalgurli mine, and Mr. Ernest Williams, general manager of the Boulder Perseverance mine. This collection was supplemented by a number of small specimens, including the rare copper telluride, which were collected and preseryed from the Kalgurli mine by Mr. A. E. Paton, and also by a few miscellaneous specimens from the collection o{ Mr. S. F. C. Cook, of the Palace Hotel, Kalgoorlie.An extensive knowledge of the rare tellurium-bearing minerals was compiled during the last century from occurrences in Transylvania and Colorado. The recognition of different species has been based on chemical analyses and crystallographic measurements. In a few species there has been an absence of crystalline form, and these, together with the discoveries in this century of rickardite and "weissite" muthmannite and empressite, have depended chiefly on the chemical analysis for identification. On the other hand, the crystalline form of nagyagite and stiitzite has been described in detail, while their precise chemical formulae were doubtfully defined.

Jan 1, 1931

By S T. Jarvis

Colliery spoil is the major constituent of colliery spoil ærockpasteÆ which has been used to infill abandoned limestone mines in the West Midlands of England since the early-1980s. The other constituents of rockpaste are pulverised fuel ash, lime and water. A key property of the rockpaste is its ability to flow within the mine workings over considerable distances before setting. This paper describes the work carried out to identify suitable sites as sources of colliery spoil for making rockpaste and goes onto consider the flow properties of the material and the monitoring methods used on-site. A full-scale trial comprising infilling a 6600 m3 section of an abandoned mine was conducted prior to the infilling of the Littleton Street Mine which had a volume of about 500 000 m3. As well as describing the methods used for monitoring the movement of rockpaste material, a description is also given of a dip-meter developed specifically for the purpose of measuring the level of paste in the mine. This paper shows how a colliery spoil based paste has been successfully used for infilling abandoned mine workings. The monitoring systems developed for use in the two case studies presented in this paper are now being used extensively for infilling other abandoned mine workings. To-date over 11 mines with a total volume exceeding two million cubic metres have been backfilled.

Jan 1, 1998

By R Benton

Since commencement of underground production in March 2006 the Kencana K1 orebody has delivered over 0.9 Mt of ore containing 1.18 Moz Au until April 2009. The Kencana deposits are part of the Gosowong goldfield located on the island of Halmahera in eastern Indonesia. The district has produced over 2.3 Moz since mining commenced in 1999 with the first two deposits extracted by open pit methods. The K1 deposit is technically challenging being a vein style deposit with poor to very poor ground conditions and a relatively low overall dip of around 45 degrees to mine grid east. It is mined under geological control by underhand cut and fill methods utilising cemented paste backfill aiming for 100 per cent extraction. With these conditions the operation was mine limited in the initial two years of production resulting in low stockpile levels for mill feed blending and hand-to-mouth mine to mill production. Mill feed rates have increased from 30 t/h to 55 t/h over this period following business improvement projects while mine production has escalated to match this increase as deeper levels of the deposit are accessed. The operation has now become mill limited. Monthly mill gold production from Kencana has ranged up to 50 000 oz with head grades ranging between 8 g/t and 122 g/t Au on a daily basis. As individual grade control assays can extend into the per cent Au range there are challenges in sampling, modelling, mining, blending and milling the Kencana orebody. At the time of commencement of ore driving in K1 the national geology team had little prior experience in underground mining and systems were in early development. The variances in feed grade and tonnages have been reduced with time as the operation evolves and business improvement initiatives are undertaken to smooth peaks and troughs in ore supply. Two such initiatives in the geology department have added over US$20 M of additional revenue per annum.

Jan 1, 2009

The need for ventilation around mine workings derives from the various gases found in mine atmospheres and CH4, the principal diluent is in quantity depending upon several factors. Several of these are seam thickness, depth of cover and working method and the French Regulations typify controls on coal mine ventilation. There are many factors affecting production of CH4, in addition to coal production, such as the geological setting of the working seam, the geometry of workings and the rates of advance. The possibilities of spontaneous combustion should not be overlooked. The complexity of high production modern colliery layouts is such that sometimes there maybe 200 airway branches. There are specific differences in ventilation networks between the mining methods of rooms and pillars, shortwalls and longwalls as affecting resistance losses, as well as necessary airflows and ventilating

Jan 1, 1983

By G W. Scott, R C. Johnson

Hypogene alteration zones have been described as a precursor to high-grade haematite deposits in Australia, Brazil and elsewhere. This alteration is described as being below or distal and is typically magnetite-carbonate-silicates reflecting Mg - Fe metasomatism. This paper describes, without genetic implication, the mineral zonation and possible structural control on mineralogic variation within the Tilden Mine, a concentrating grade haematite deposit in Michigan, USA. In contrast to the high-grade deposits, these variations are not peripheral to the orebodies but are the ore. The deposit occurs within the Negaunee Iron Formation, along the southern margin of the Paleoproterozoic Marquette Range Supergroup basin. The regional structure is a fault-bounded west plunging syncline within the crustal scale Great Lakes Tectonic Zone, which forms the boundary between Archean granite-greenstone and gneissic terranes. Local structure consists of second-order anticlines and synclines with variable northwest and southwest plunges. The interaction of sedimentation and diagenesis within growth fault controlled basins, along with a possible metamorphic and/or hydrothermal overprint has resulted in a complex series of ore types. For modelling purposes, the deposit is divided into geologic domains based on both lithology and metallurgical response in the laboratory and in the plant. Mineralogic variation is recognised within individual mineral grains; at blast pattern (10 - 15 m) and development drill hole (100 m) scales.

Jan 1, 2007

The structural pattern of Victoria shows the presence of EW, NW, NE as well as the more readily recognised NNW factors commonly associated with the goldfields. ENE and WNW trends are also present. This structural lattice affects all rocks of the State. Landsat imagery shows that the EW, NW and NE structural elements are closely related spatially to the distribution of Palaeozoic igneous intrusives, Cainozoic volcanic vents as well as all historically important gold mines. It is suggested that the EW, NW and NE structural grid visible on landsat imagery is a reflection of the structure of a mid-crustal layer situated between 3.5 and 17 kms below the surface. The points of intersection of the structural elements of the mid-crustal layer offer most favourable loci for the escape of energy in the form of heat. The correlation between the distribution of igneous plutons, volcanic vents and centres of mineralisation, all reliant on high levels of energy for their formation, indicates the stability of the structures of the mid-crustal layer since early Palaeozoic times. The deep level crustal structures are believed to be, related to the release of stresses placed on the crust since early Palaeozoic times by the rotation of the Earth. A geological model that accommodates the presence of a mid-crustal layer as well as the complexities of the recognised orogenic cycles of southeast Australia is suggested. All 1 000 kg Au reef and deep lead mines fall within 1.5 and 2.5 km respectively of strong linears associated intimately with plutons and volcanic vents. Future exploration of the State is more likely to meet with success if it too is confined to the evaluation of these and similar linears. The mode of mineralisation of any one centre will depend upon the temperature, pressure and geochemical gradients operating on the migrating mineralising fluids as well as the structures in the host rocks. These factors are likely to have varied considerably from one centre of mineralisation to the next and consistency of mineral isation form and depth should not be expected along the length of any single Linear.

Jan 1, 1986

By Jankowski P

The Bannockburn gold deposit is located 67 km north-west of Leonora in a poorly exposed part of the Norseman-Wiluna belt of Western Australia. The deposit consists of narrow, complexly shaped orebodies which have presented a challenge to find successful grade control and mining methods. The deposit also presents an opportunity to examine in detail the geology of this part of the Norseman-Wiluna belt.This paper discusses the geology and structure of the Bannockburn gold deposit as well as the grade control and mining systems developed to define the ore and extract it with minimum dilution. We discuss the different techniques employed for grade control in the past and their shortcomings, and the evolution of the present system of doing grade control in cross section from blast hole assays.

Jan 1, 1993

By Weller KR, Lim IL

The high pressure grinding rolls is one of the few new comminution devices that offer substantial savings when compared with traditional crushing and grinding circuits and with SAG milling. The machine has been well accepted in the cement industry, but mining companies have been more cautious in adopting this technology, partly because of wear and availability problems, and partly because of uncertainties in designing circuits which will deliver the power savings without complicating downstream processing. This paper addresses the latter problem by providing a model structure for predicting power draft and throughput from measurements made with small pilot scale high pressure rolls. Three existing models for predicting product size distributions are assessed and suggestions made for future work. The model structure comprises a power equation, incorporating measurements of torque and rolls speed previously used by the authors. Transport through the mill is assumed to be plug flow. Throughput is governed by the equilibrium gap between the rolls, which is determined both by machine settings and the physical properties of the feed material, including its size distribution. Therefore some form of physical testing in a model machine is required to determine throughput parameters. Results from copper and nickel ore experiments covering a wide range of machine conditions are presented and compared with model predictions. Model assumptions are discussed and directions for future work Suggested.

Jan 1, 1993

By R Graber, R Johnson

North American steelmaking practices have evolved based on access to iron ore raw materials containing very low phosphorus contents, typically less than 0.025 per cent P. Cleveland-Cliffs managed Tilden iron ore operation produces iron ore pellets exceeding 0.030 per cent P, which by global standards would be considered low phosphorus, but has limited penetration in the North American iron ore market due to phosphorus content. Recently cathodoluminescence microscopy has augmented more standard ore characterisation techniques enhancing our understanding of the genetic history and process mineralogy of TildenÆs complex martite ore. This paper highlights the unique capabilities that cathodoluminescence microscopy provides for phosphorus mineral identification in fine-grained iron ores.

Jan 1, 2005

The author describes 1. The classification and characteristics of various thick seam mining techniques in various Japanese coal mines. 2. Practices of thick seam mining methods experienced in Taiheiyo Coal Mine. Currently, thick single lift, simultaneous multi lift and non simul- taneous multi lift mining methods are adopted as underground flat thick seam excavations in Japan. These are now reliable and effective in increasing the extraction ratio. At Kushiro Colliery of Taiheiyo Coal Mining Co., these three thick seam mining methods have been used. According to the results, if solidification of the top lift goaf is essential, the non simul- taneous multi lift mining method is the most effective in increasing the extraction ratio without minimising productivity of each lift and it points out that further development of this method is necessary.

Jan 1, 1976