Search Documents

By Jiaxin Zhou

Acid mine drainage is a serious and chronic environmental problem of mining. This paper discusses the factors affecting the rate of acid generation by mine rocks and illustrates the relevance of these factors to the mines of the Northern Territory, Australia. The factors may be divided into two groups: internal factors and external factors. The first group covers characteristics of ores, mine waste rocks, tailings, etc and the second group covers surrounding conditions. The latter is further divided into four sub-groups, viz surrounding temperature and pressure, chemical conditions (ferrous/ferric adsorption ratio, total iron concentration, oxygen concentration and pH), surrounding biological conditions and mechanical conditions. Special attention is given to the surrounding P-T conditions, especially water partial pressure, and its relevance to the Northern Territory mines.

Jan 1, 1994

By R-H Yoon

The thin film pressure balance (TFPB) technique was used to measure the kinetics of thinning of single foam films and disjoining pressures in the presence of sodium dodecyl sulfate (SDS) and electrolyte (NaCl). The results were analysed in view of the Reynolds equation to determine the role of surface forces in film thinning. It was found that film thinning is controlled by surface forces at thicknesses below approximately 200 nm. It was also found that hydrophobic force plays an important role particularly at low SDS and NaCl concentrations. The values of the hydrophobic force constant (K232) estimated from the film thinning experiments were used to predict the disjoining pressure isotherm using the extended DLVO theory, which were found to be in excellent agreement with experiment. The TFPB technique was also used to measure the equilibrium thicknesses (He) of the foam films stabilised by a non-ionic surfactant, n-octanol, in the presence of NaCl. At a given ionic strength, He increased noticeably with increasing octanol concentration at very low concentrations. This observation suggests that hydrophobic force is at its maximum level in the absence of surfactant and decreases with increasing surfactant concentration. The results obtained with the single foam films were used to explain the stability of the three-dimensional foams.

Jan 1, 2005

By K Muller, T Oosthuizen

Blast exclusion zones are instrumental in protecting equipment and personnel. When there is no constraint in footprint, the exclusion zone can be enormous, practically eliminating the hazard of flyrock. Unfortunately, this may not always be the case and in many circumstances the blast design needs to be altered to suite such scenarios. When a conservative design approach is taken, it could completely eliminate any form of ejection, whether it is from the free face or the bench itself. The degree to which typical flyrock models describe fragment motion through air with ballistic flight equations are not justified when such a high level of control is applied. This paper examines various methods of risk analysis and suggests an approach to be used for controlled blasting.The outcome of principles discussed in this paper can be seen in video form (Mavmedia, 2014).CITATION:Muller, K and Oosthuizen, T, 2015. Should the blast exclusion zone be based on a qualitative or quantitative analysis? A practical implementation conundrum, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 425–428 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By I Lipton

The existence of metalliferous mineral deposits on the deep-sea floor has been known since manganese nodules were discovered in the Arctic Kara Sea in 1868. Modern exploration to define commercially viable base and precious metal deposits began in the 1970s and gained further momentum in the last decade. High grade deposits have been delineated but investors remain cautious, many considering deep sea mining projects to be riskier than terrestrial projects. This paper compares opportunities and risks presented by terrestrial mining projects with those presented by deep sea mineral deposits (Table 1). The Solwara 1 volcanic-hosted massive Cu-Au-Ag sulphide deposit, the Atlantis II Deeps sedimentary base metal sulphide deposit, and the Mn-Ni-Cu-Co nodule deposits of the north-eastern Pacific Ocean are used as examples. These are advanced deep-sea projects with published Mineral Resource estimates, on the cusp of development. Off-shore diamond mines in Namibia are also considered. These examples provide a basis for comparing exploration and geological uncertainty, the technical risks of proposed mining systems, and the potential environmental and social impacts. CITATION: Lipton, I, 2018. A comparison of opportunity and risk in deep-sea and terrestrial mining projects, in Proceedings Complex Orebodies Conference 2018, pp 102–105 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

By O Handayani, R Barr, E Isaaks

The mining industry has focused a great deal of attention recently on the impact of blast movement on grade control. Although the problem of blast movement and its contribution to dilution and ore loss is well known, solutions to the problem are less than satisfactory. Perhaps the most recent innovation is the application of blast movement monitoring (BMM) devices to quantify blast movement. These devices emit an electronic signal and are planted at surveyed locations within the preblast material. Following the blast, their new locations are found using an electronic scanner. The magnitude and direction of the blast movement is given by the vectors between the pre- and post-blast BMM locations. However, it’s not clear how the BMM vector data can be best used to minimise dilution and ore loss. One common solution is to displace preblast dig line polygons by distances indicated by the BMM vectors. However, studies of BMM vectors show that blast movement not only displaces material laterally but also mixes material internally within the bench (Thornton, 2009a).This paper presents a method for modelling the post-blast muck pile that accounts for displacement and internal dilution using simulated annealing. The preblast ore control block model is re-blocked to 1?×?1?×?1?m sub-blocks. Each sub-block is displaced by simulated BMM vectors conditional to post-blast surface topography and blast initiation sequence data in addition to BMM vector data. The displaced sub-blocks are aggregated into new ore control model blocks whose grades are calculated from the contained sub-blocks. New dig lines are then designed on the post-blast muck pile model using the new ore control block model grades. A case study based on actual data is provided.CITATION:Isaaks, E, Barr, R and Handayani, O, 2014. Modelling blast movement for grade control, in Proceedings Ninth International Mining Geology Conference 2014 , pp 433–440 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 18, 2014

By J Rose, D O’Toole, D Grant

Orepasses are a critical element in the transport of ore from the stope drawpoint to the surface ore stockpile, making them an integral part of an underground mine’s ore-handling system. Well-designed and operated orepasses improve productivity and lower operating costs over a long period of time.The Olympic Dam mine, as part of a 6 Mt/a expansion project in 1997, constructed a large network of orepasses feeding a rail haulage system to facilitate the movement of approximately 8 Mt/a to the Clark crusher and hoisting shaft. The orepass network comprises 14 orepasses and currently includes 59 individual tip points. The orepass network has been in operation for over 15 years and in excess of 110 Mt of ore has been moved through the system.Olympic Dam’s management of mine infrastructure includes a program of assessing the condition of the Clark system orepasses. A comprehensive program was initiated in 2011 and consisted of systemically performing volumetric surveys to determine the integrity of the various sections of the orepasses. The current geometrical state of the orepasses provides essential information for comparison of geotechnical and operational parameters and a baseline for understanding the key causes of orepass deterioration to assist in the planning of both usage and potential replacement options.The collection of geotechnical and operating data allowed the review of the current condition, potential longevity and associated risks with the various orepass sections. Initial studies have also reviewed options for rehabilitation and/or replacement.CITATION:Rose, J, Grant, D and O’Toole, D, 2016. Orepass monitoring and management at Olympic Dam Mine, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 609–616 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By C McGuire

As mobile equipment electrification in underground mining continues to gain popularity, control ofheat and humidity in the workplace is becoming a key driver in sizing of ventilation and mine aircooling systems. For design and sizing of ventilation and cooling systems to be accurate, and for themine mobile equipment fleet to be sized appropriately to meet production goals, vehicle productivitymetrics, heat modelling, and energy balances for electrified fleets need to consider operation througha realistic duty cycle that is reflective of various tasks performed during a shift.The authors conducted a real-world comparison of two 8 cubic yard (14 metric tonne) class Load-Haul-Dump (LHD) machines – one diesel and one battery-electric vehicle (BEV) – performingidentical muck-haul-dump operations on consecutive days at an underground nickel/copper hardrock mine in Ontario, Canada.The battery-electric LHD averaged 8.9 per cent faster cycle time than the diesel vehicle (gross,without accounting for charging time), and was able to transport 25 per cent more material per cycledue to a larger bucket capacity. When including the charging time, average net cycle times wereequivalent for the two vehicles over the 200 cycles. The BEV carried more payload over the eighthour period due to the increased capacity per cycle.The testing identified an approximately five-fold reduction in heat output from the BEV in comparisonto the diesel LHD on a basis of heat output per tonne of rated bucket capacity. Heat output from thefast charger was found to be approximately 4 per cent of the charging rate, with negligibletemperature change observed in the main drift. External noise levels in the mine were found to be14 dB lower for the BEV during transit and 11 dB lower during bucket loading. Fuel/energy costs forBEV electricity input were approximately four times lower per operating hour than diesel fuel costbased on typical 2021 electrical and diesel unit rates for a grid-connected mine in Ontario, Canada.

Oct 12, 2022

By H Kurth, L Balzan

The potential for bulk diversion was identified and quickly implemented following the development of bulk sensing technologies applied to conveyed flows. In the early 1980s real time analysis of ash in coal was intended to improve the understanding and control of quality variability. By the end of the 1980s approximately 5% of coal analysers installed were being utilised for bulk sorting; diverting flows to create stockpiles to improve blending flexibility and boiler feed consistency, diverting waste material, or bypassing the beneficiation process when the coal met product quality criteria. In the 1990s bulk sensing and sorting utilising natural gamma detection was applied to conveyed waste in gold-uranium mineralisation and allowed ore to be recovered and processed that would otherwise have been discarded. Further applications developed in the iron ore sector where product quality ore could be diverted to bypass beneficiation and save significant unnecessary processing costs and improve recovery by avoiding process inefficiency losses. Plant capacity was freed up to be utilised by material that required processing. Similar benefits became evident in the phosphate industry and in base metals where multi-elemental analysis using Prompt Gamma Neutron Activation Analysis provides ideal opportunities to representatively measure 30 second conveyed increments at high accuracies. This has been successfully adopted in copper, nickel, platinum and lead-zinc to improve waste removal after primary crushing to eliminate unnecessary expense and improve plant efficiency. The benefits include increased output from existing operating capacity, significant reductions in consumable costs and generation of fewer detrimental waste streams. The paper outlines the technologies and discusses case studies covering the above commodities, demonstrating the immense value that representative real time measurement of conveyed flows can create. Measurement data concurrently provides multiple benefits in operational performance besides sorting, through ore reconciliation, ore blending, feedforward control and metal accounting, adding further value.

Nov 10, 2020

By J Jackson

The term geometallurgy (or geometallurgical) first appeared in the literature some 40 years ago and has a wide range of definitions and perspectives which increases the barriers of communication between practitioners and across functional groups and management levels within organisations. However the consistent theme running through the diversity of definitions and perspectives is the requirement for close collaboration between the relevant disciplines. This concept of geometallurgy arguably goes back to the earliest days of the exploitation of mineral deposits, through the mid-1500s to the beginning of the 20th century.This holistic and integrated view was diminished during the 20th century due to a number of factors which included the commencement and continuing upward trend of large-scale mining and the expansion in production, the rise of scientific and classical management theories and methodologies, increase in specialisation and the development of traditional project planning. The re-emergence of geometallurgy in the late 20th century required the relevant functional units and disciplines to collaborate as a team. This necessitates a common understanding that the geometallurgical program’s goals must be obtained, which requires clear and consistent communication, particularly with the modern trend of virtual teams.A multi-dimensional construct is proposed to assist in providing a consistent approach in the communication of the context and purpose of both general and specific geometallurgical programs, thus simplifying communication. This geometallurgical construct consists of the dimensions of process span, response knowledge, variability knowledge, spatial knowledge, application and project phase in relation to extraction process(es) applied to geological materials from a mineral deposit. These dimensions are then linked to the phase of mineral project development in which the geometallurgical program is being applied, which ranges from advanced exploration through to operational execution. This paper outlines the multi-dimensional construct with examples of how the context, purpose and scope of geometallurgical programs can be clearly delineated and communicated.

Sep 5, 2011

By D Maldonado

BlueScope Steel’s Port Kembla sinter machine underwent a major upgrade during mid-2009. The mixing and rolling drum (MRD) was thoroughly cleaned during the upgrade. Space factor measurements taken in October 2009 showed that the drum was operating in the cataract regime in the dry mixing section and the cascading regime in the rolling section, which is optimal for granulation. Sampling carried out during an entry into the MRD showed that both the Sauter mean diameter and the predicted bed voidage increase rapidly during wetting, and then decrease in the wet mixing section. In the rolling section, the granule properties remained constant untilthe drum discharge. Frozen particle analysis, using liquid nitrogen as the quenching agent, were carried out on material collected from the MRD discharge. The results, expressed as a Granulation Index, showed there had been a significant improvement in the granulating performance of the MRD following the upgrade. The plant studies were also complemented with laboratory scale experiments which aimed to optimise the granulation process. The effect of burnt lime on green feed permeability was quantifi ed using the laboratory scale drum at different moisture contents. A significant increase in permeability was apparent once the burnt lime dosing rates doubled from 1.1 - 2.2 per cent w/w (feed basis). The capacity of the burnt lime system at the sinter machine will be increased in order to benefi t from the expected higher permeability, permeability, which will enable the machine to sinter at deeper bed heights.

Jul 11, 2011

Cannington Mine is an underground, hard rock, metalliferous mine located in North-Western Queensland, Australia. Weld mesh is installed to prevent the failure of rock from between the installed reinforcement elements. Corrosion reduces the capacity and life expectancy of mesh and presents a real hazard to underground personnel and equipment as it reduces the effectiveness of the support system. Corrosion influences the economics of the mining operation through the need to conduct rehabilitation of the ground support which involves re-installing new mesh or shotcreting over the affected mesh to protect it from further corrosion. The requirement for rehabilitation is determined by the geotechnical engineer based on an individual visual assessment with little or no engineering input. It was identified that a more quantitative method was required that considered the safety and economic risks involved. A project was undertaken to develop a simple method to evaluate corroded mesh and to provide selection criteria for rehabilitation. A weld mesh corrosion classification has been developed that relates the average wire diameter of corroded mesh to the remaining capacity of the mesh. Accompanying selection criteria provides recommendations as to when rehabilitation may be required based on the estimated residual mesh capacity, the remaining development life, and the level of personnel exposure.

Nov 25, 2010

By I Neilsen, A Walker, A Hooper

Final landform planning in Deswik software was used to determine if integration into the mine plans could achieve better closure outcomes. Using the dump surface outputs from the Deswik Landform and Haulage Simulation (LHS) and the Reshape Landform tool, the project intended to:1.Review costs to achieve the final landform for several grade criteria scenarios;2.Quantify reshape volumes at several stages of the mines development with the objective to contribute to margin ranking inputs; and3.Identify rehabilitation cost reduction measures such as backfilling ramps and pits.CITATION:Neilsen, I, Walker, A and Hooper, A, 2018. Case studies for integrating rehabilitation planning with mine planning in strip mining, in Proceedings Life-of-Mine 2018, pp 93–95 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By A G. Guinea

Every person in an organisation has what could be called ‘a different take’ on what it means to be a safety leader. The directors will tell you they are ultimately responsible for everyone’s safety and that they can be imprisoned as a consequence of a workplace fatality. Managers, take more of a focused approach and would explain that they are totally responsible for the safety of their teams. And then there are front-line leaders. Those that not only have the responsibility (like directors and managers) but they also have the accountability, and the ability, to influence how safely their teams work. But it is not just physical safety that leaders should be concerned with.

May 5, 2022

By P Card

“Let’s get discipline and quality into easy to understand evaluations!” Project Managers and MetPlant Operators accept poor quality evaluations because they are generally unaware of what they should expect.The 2010 draft AusIMM ‘Guidelines for Techno-Economic Evaluations’ were collated by a subcommittee of practitioners and are regarded as best practice.They apply directly to projects and metallurgical plant evaluations, including those with a heavy technical basis. They can be applied to technical problem solving where there are no monetary computations. Project Managers and MetPlant Operators should demand that economic models and evaluations follow the six principles. They should become working tools which are easy to understand, fit for purpose, consistent, rigorous, record sources of input data, have key graphs and are rapid to audit.

Aug 8, 2011

By B Hawkins, S Durkin, V Lawrence

The requirement for secondary egress from underground workings has long been regulated in Australia. Escape way systems have evolved from simple airleg rising ladders and timber ladders to steel galvanised ladders and more recently fully enclosed polyethylene ladders.The polyethylene ladder, Safescape Laddertube, was introduced to the underground mining industry in 2010. It is an enclosed cylindrical modular plastic ladder designed for use in underground escape ways and access ways. Since its first installation in May 2010, the Laddertube has been installed in 43 mines across four countries, totalling 8800 m of ladders installed to December 2013.The Cracow Gold mine is one operation using Laddertube, located 500 km north-west of Brisbane, Queensland, Australia. Upon discovering and developing both the Empire and Roses Pride orebodies, a safe and economically viable secondary egress system and surface primary ventilation exhaust shafts were necessary to support development and production activities to these workings. The need arose to merge these two critical requirements together between surface and underground mine workings some 200 m and 400 m respectively for each orebody. Neither egress has intermediate access points within their full service length from top to bottom. Several options were considered, the preferable and most feasible method adopted was Laddertube.The longest egress length requiring Laddertube within the two vertical surface exhaust shafts was 400 m long, within a 3.5 m diameter shaft. Due to the length of the vertical Laddertube system in both egresses, personnel are to be assisted by mechanical means using the Extended Ladder Climb Assist system.The Gossan Hill mine also uses Laddertube for their escape ways. Part of the Golden Grove operation, Gossan Hill is an underground sublevel open stoping mine located in the mid-west of Western Australia.With a considerable mine life remaining and a history of acidic water and stress related deterioration in vertical openings, the mine operators sought an escape way solution that would provide for the long-term needs of Gossan Hill. Laddertube was selected due to its non-corrosive properties and the ability to fill in around the ladder way to provide stability to the raise opening.Laddertube is a recent development in escape way systems, and is effectively being applied in a variety of operations, meeting the specific needs of underground mines.CITATION:Durkin, S, Hawkins, B and Lawrence, V, 2014. The application of Safescape Ladders at the Cracow and Golden Grove operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 311–318 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By S C. Dominy

Gravity amenable gold ores are those that after comminution produce liberated particles, composites and/or carriers that can be recovered by gravity separation means. Recovery depends upon mineralisation type and the comminution and concentration method used. Any in situ ore with more than 20 per cent of gold greater than 100 µm in size is likely to have a strong gravity recoverable component. A less traditional approach is where the gold is sulfide-locked and the gold carrier plus any liberated gold is recovered via continuous gravity recovery following fine crushing. Specific tests are undertaken to determine the level of gravity amenable gold within a deposit. The principal methodology is the gravity recoverable gold (GRG) test, which consists of three sequential liberation and recovery stages. For continuous gravity recovery (CGR), the sample is fed over a laboratory Wilfley table to simulate continuous recovery of the gold. Tails from the feed can be progressively re-ground and re-tabled to develop a grade-recovery curve. Primary geology and gold particle size-distribution have a strong effect on the mass of sample required to provide representative results for both tests. Where low-grade ore contains very coarse gold, substantially larger sample masses are required. Experience has shown that GRG and CGR values can vary throughout an orebody, particularly within different geological-grade domains. A testing regime must consider sample frequency and support.

Sep 5, 2011

By G Anderson, V Lawson, P Voigt

Glencore operates zinc concentrators at both Mount Isa and McArthur River. Both orebodies have a history of complexity and required the development of new technologies to maximise the value from these long-life assets. The Mount Isa orebodies were plagued since operations started in 1931 with complex mineral textures making separation challenging and many areas uneconomic. Examples are given in Figure 1 with different grain sizes from the same orebody in different areas. The McArthur River deposit, located in the Northern Territory, was discovered by Mount Isa Mines geologists in 1955 (Logan, Murray and Williams 1990). The extremely fine-grained nature of the ore was quickly recognised and the difficult separation of the minerals was soon obvious. The geographical, metallurgical and economic factors resulted in the orebody not being developed until the technologies for the mineral separation had been developed. The development of the IsaMill allowed for an economic mineral separation flowsheet to be developed and ore treatment commenced in May 1995 (Nihill, Stewart and Bowen 1998). CITATION: Lawson, V, Anderson, G and Voigt, P, 2018. Developing technologies for a complex orebody, in Proceedings Complex Orebodies Conference 2018, pp 116–118 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 21, 2018

Two characteristics of the modern mining industry are that there is a skill shortage and that young professional people rise rapidly into highly responsible supervisory positions. With this responsibility comes the burden of identifying and managing health and safety risks. Without the benefit of a comprehensive health and safety training program, these young professionals may be putting both themselves and those under their supervision at risk. The Moura Mine explosions and the asbestos health disaster should not be just artifacts of history, but highly valued lessons that impress the need for comprehensive health and safety risk management strategies on young professionals. From the perspective of the former secretary of the Committee to implement the findings of the Moura (Disaster) Inquiry and as the former coordinator of the Coal Workers Health Scheme, key issues in occupational health and safety management systems are explored.

Jan 1, 2005

By X Hu, Z Pokrajcic, R Embry, P C. Stewart, J Carpenter, E Jones

Whilst the value of Pit to Plant and Mine to Mill optimisation has been proven since the 1990s, sustaining the productivity and efficiency gains typically requires ongoing test work, blast trials, plant surveys, and model calibration services. In contrast, the input to digital twin Pit to Plant or Mine to Mill optimisation is tens to hundreds of millions of tonnes of standard mine operating data. This paper presents a series of digital twin case studies from across the mine value chain, including machine learning testing methodology, model accuracy statistics and the application of Shapley Additive Explanations (SHAP) for model interpretation. These case studies demonstrate how machine learning and data fusion ore tracking connects hundreds of millions of tonnes of downstream performance data to produce digital twin models (operating models that are continuously updated and integrated into the wider Mine to Mill/Pit to Plant ore tracking system). Digital twin modelling software has been used to add block model variables for dig-rate, crusher and mill throughput, recovery (tailings grade), lump yield, product grade and product quality, fines yield and fines in lump. Block-by-block predictions are added to the geological resource and grade control block models as new block model variables. These new block model variables are used across all mine planning time horizons from life-of-mine planning to daily schedules. In addition to the materials handling and geometallurgical prediction case studies, the paper also presents digital twin case studies for drill and blast simulation and plant set point optimisation. The case studies show how digital twin simulation enables drill and blast engineers to simulate the effect of different blast designs in different blast domains using the mines operating data. Plant set point optimisation applies mathematical optimisation algorithms to the machine learning model to provide live operational decision support to metallurgists and plant operators. The digital twin machine learning case studies demonstrate a digital and sustainable paradigm for Mine to Mill and Pit to Plant optimisation.

Jun 22, 2022

By K White, C Ferguson, M Harding

Understanding watercourses and river processes at a landscape scale is vital for managing risk to mining infrastructure and operations as well as minimising future environmental impacts beyond the life of the mine. Recognising this, Iluka Resources Limited engaged Alluvium Consulting Australia to identify and characterise watercourses across several neighbouring mineral tenements in the Eucla Basin, South Australia (Alluvium, 2013, 2014a, 2014b). The objective of the studies was to inform planning for risk management during mine planning and operation and appropriate landscape rehabilitation for mine closure.Mining operations in the area are by open cut extraction of mineral sands. The extracted resource is processed on-site before leaving the site for export. Several pits are to be developed in stages with simultaneous backfilling and surface reinstatement. Mining is initially taking place in the Jacinth tenement, where up to 100 km of watercourses may be directly or indirectly impacted (refer to Figure 1).The total study area (shown in Figure 1) is approximately 330 km2 and spans three smaller areas that were the focus of separate investigations during mine planning.CITATION:Ferguson, C, White, K, Harding, M and Hardie, R, 2016. Landscape-scale assessment of watercourses in remote arid South Australia to inform mine planning to mine closure, in Proceedings Life-of-Mine 2016 Conference, pp 200–204 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016